Control motors, vehicles without air conditioner operating unit at rear

In this manual: Control motors, vehicles without air conditioner operating unit at rear
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
6steps
~36min
2/5difficulty
010203040501.51N·mlb·ft
Tightening torque found on this page
Done 0 of 6
  • Overview of fitting locations - control motors (front)
  • Exploded view - control motors (front)
  • Removing and installing control motor for front left temperature flap [VX34], LHD vehicles
  • Removing and installing control motor for front left temperature flap [VX34], right-hand drive vehicles
  • Removing and installing control motor for front right temperature flap [VX35], left-hand drive vehicles
  • Removing and installing control motor for front right temperature flap [VX35], right-hand drive vehicles
  • Removing and installing control motor for defroster flap VX47
  • Removing and installing control motor for front left air distribution flap [VX93], left-hand drive vehicles
  • Removing and installing control motor for front left air distribution flap [VX93], right-hand drive vehicles
  • Removing and installing control motor for front right air distribution flap [VX94], left-hand drive vehicles
  • Removing and installing control motor for front right air distribution flap [VX94], right-hand drive vehicles
  • Removing and installing control motor for fresh air and air recirculation flap [VX96]
  • Removing and installing actuator for left air distribution flap

Overview of fitting locations - control motors (front)

Volkswagen ID.4. Overview of fitting locations - control motors (front)
  1. Control motor for fresh air and air recirculation flap - VX96-
  • With fresh air/air recirculation, air flow flap control motor - V425-
  • With potentiometer for fresh air/air recirculation, air flow flap control motor - G644-
  • ⇒ Rep. gr. 87 ; Removing and installing control motor for fresh air and air recirculation flap VX96

Control motor for front left temperature flap - VX34-

  • With left temperature flap control motor - V158-
  • With potentiometer for left temperature flap control motor - G220-
  • ⇒ Rep. gr. 87 ; Removing and installing front left temperature flap VX34
  1. Control motor for front left air distribution flap - VX93-
  • With front left air distribution flap control motor - V706-
  • With potentiometer for front left air distribution flap control motor - G1105-
  • Rep. gr. 87 ; Removing and installing front left air distribution flap control motor VX93
  1. Control motor for rear temperature flap - VX95-
  • Depending on equipment/vehicle version
  • With rear temperature flap control motor - V137-
  • With potentiometer for rear temperature flap motor - G479-
  • ⇒ Rep. gr. 87 ; Removing and installing control motor for rear temperature flap VX95
  1. Control motor for front right air distribution flap - VX94-
  • With front right air distribution flap control motor - V707-
  • With potentiometer for front right air distribution flap control motor - G1106-
  • ⇒ Rep. gr. 87 ; Removing and installing control motor for front right air distribution flap VX94
  1. Control motor for front right temperature flap - VX35-
  • With right temperature flap control motor - V159-
  • With potentiometer for right temperature flap control motor - G221-
  • ⇒ Rep. gr. 87 ; Removing and installing control motor for front right temperature flap VX35
  1. Control motor for defroster flap - VX47-
  • With defroster flap control motor - V107-
  • With potentiometer for defroster flap control motor - G135-
  • ⇒ Rep. gr. 87 ; Removing and installing control motor for defroster flap VX47

Exploded view - control motors (front)

Exploded view - control motors (front left)

  1. Control motor for front left temperature flap - VX34-
  • ⇒ Rep. gr. 87 ; Removing and installing control motor for front left temperature flap VX34
  1. Bolt
  • 1,5 N·m
  1. Control motor for front left air distribution flap - VX93-
  • ⇒ Rep. gr. 87 ; Removing and installing control motor for front left air distribution flap VX93 - left-hand drive vehicles
  1. Actuator
  2. Heater and air conditioning unit
  • ⇒ Rep. gr. 87 ; Removing and installing heater and air conditioning unit
Volkswagen ID.4. Exploded view - control motors (front left)

Exploded view - control motors (front right)

  1. Heater and air conditioning unit
  • ⇒ Rep. gr. 87 ; Removing and installing heater and air conditioning unit
  1. Bolt
  • 1,5 N·m
  1. Control motor for defroster flap - VX47-
  • ⇒ Rep. gr. 87 ; Removing and installing control motor for defroster flap VX47
  1. Actuator
  2. Control motor for front right air distribution flap - VX94-
  • ⇒ Rep. gr. 87 ; Removing and installing control motor for front right air distribution flap VX94
  1. Control motor for front right temperature flap - VX35-
  • ⇒ Rep. gr. 87 ; Removing and installing control motor for front right temperature flap VX35
Volkswagen ID.4. Exploded view - control motors (front right)

Exploded view - control motors (front), air intake box of heater and air conditioning unit

  1. Bolt
  • 1,5 N·m
  1. Control motor for fresh air and air recirculation flap - VX96-
  • ⇒ Rep. gr. 87 ; Removing and installing control motor for fresh air and air recirculation flap VX96
  1. Actuator
  2. Heater and air conditioning unit
  • ⇒ Rep. gr. 87 ; Removing and installing heater and air conditioning unit
Volkswagen ID.4. Exploded view - control motors (front), air intake box of heater and air conditioning unit

Removing and installing control motor for front left temperature flap [VX34], LHD vehicles

Removing

The front left temperature flap - VX34- with left temperature flap control motor - V158- and potentiometer for left temperature flap control motor - G220- will henceforth be referred to as control motor.

Mark position of control motors and connectors prior to removal to avoid interchanging control motors at reinstallation.

  • Deactivate function "Stationary air conditioning" ⇒ Owner's manual .
  • Release mounting bracket ⇒ Brake system; Rep. gr. 46 ; Brake pedal; Removing and installing mounting bracket .
  • Disconnect electrical connector -3-.
  • Unscrew bolts -2- and -4-.
  • Remove control motor -1-.
Volkswagen ID.4. Removing and installing control motor for front left temperature flap [VX34], LHD vehicles

Installing

Install in reverse order of removal, observing the following:

  • Check position of shaft -A- relative to mounting -B-.

Important

If teeth are not properly aligned, actuator -C- cannot be fitted.

Volkswagen ID.4. Removing and installing control motor for front left temperature flap [VX34], LHD vehicles
  • If control motor has been renewed or installed at different position:

Carry out function "Adapt flap limit stops of control motors" ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - front control motors

Removing and installing control motor for front left temperature flap [VX34], right-hand drive vehicles

Removing

Front left temperature flap - VX34- with left temperature flap control motor - V158- and potentiometer for left temperature flap control motor - G220- are referred to hereafter as control motor.

Mark position of control motors and connectors prior to removal to avoid interchanging control motors at reinstallation.

  • Deactivate function "Stationary air conditioning" ⇒ Owner's manual .
  • Remove footwell vent on front passenger side ⇒ Rep.

    gr. 87 ; Removing and installing footwell vent on front passenger side .

  • Remove fan for control unit - V274- ⇒ Electrical system; Rep. gr. 97 ; Control units; Removing and installing fan for control unit [V274] .
  • Disconnect electrical connector -3-.
  • Unscrew bolts -2-.
  • Remove control motor -1-.
Volkswagen ID.4.  Removing and installing control motor for front left temperature flap [VX34], right-hand drive vehicles

Installing

Install in the reverse sequence of removal, observing the following:

  • Check position of shaft -A- relative to mounting -B-.

Important

  • If teeth are not properly aligned, actuator -C- cannot be fitted.
Volkswagen ID.4.  Removing and installing control motor for front left temperature flap [VX34], right-hand drive vehicles

If control motor has been renewed or installed at different position:

  • Carry out function "Adapt flap limit stops of control motors" ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - front control motors
  • ⇒ Rep. gr. 87 ; Assembly overview - air ducts and air distribution in passenger compartment

Removing and installing control motor for front right temperature flap [VX35], left-hand drive vehicles

Removing

The front right temperature flap - VX35- with right temperature flap control motor - V159- and potentiometer for right temperature flap control motor - G221- will henceforth be referred to as control motor.

Mark position of control motors and connectors prior to removal to avoid interchanging control motors at reinstallation.

  • Deactivate function "Stationary air conditioning" ⇒ Owner's manual .
  • Remove footwell vent on front passenger side ⇒ Rep.

    gr. 87 ; Removing and installing footwell vent on front passenger side .

  • Unscrew bolts -2-
  • Disconnect electrical connector -3-.
  • Remove control motor -1-.
Volkswagen ID.4. Removing and installing control motor for front right temperature flap [VX35], left-hand drive vehicles

Installing

Install in reverse order of removal, observing the following:

Check position of shaft -A- relative to mounting -B-.

Important

  • If teeth are not properly aligned, actuator -C- cannot be fitted.
Volkswagen ID.4. Removing and installing control motor for front right temperature flap [VX35], left-hand drive vehicles

If control motor has been renewed or installed at different position:

  • Carry out function "Adapt flap limit stops of control motors" ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - front control motors
  • ⇒ Rep. gr. 87 ; Assembly overview - air duct and air distribution in passenger compartment

Removing and installing control motor for front right temperature flap [VX35], right-hand drive vehicles

Removing

Front right temperature flap - VX35- with right temperature flap control motor - V159- and potentiometer for right temperature flap control motor - G221- are referred to hereafter as control motor.

Mark position of control motors and connectors prior to removal to avoid interchanging control motors at reinstallation.

  • Deactivate function "Stationary air conditioning" ⇒ Owner's manual .
  • Remove footwell cover on driver side ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing footwell cover on driver side .
  • Move clear electrical wire -3-.
  • Disconnect electrical connector -4-.
  • Unscrew bolts -2-.
  • Remove control motor -1-.
Volkswagen ID.4. Removing and installing control motor for front right temperature flap [VX35], right-hand drive vehicles

Installing

Install in the reverse sequence of removal, observing the following:

  • Check position of shaft -A- relative to mounting -B-.

Important

  • If teeth are not properly aligned, actuator -C- cannot be fitted.
Volkswagen ID.4. Removing and installing control motor for front right temperature flap [VX35], right-hand drive vehicles
  • Route electrical wire so that it cannot come into contact with any moving parts (e.g. actuating arm on control motor).

If control motor has been renewed or installed at different position:

  • Carry out function "Adapt flap limit stops of control motors" ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - front control motors

Removing and installing control motor for defroster flap VX47

Removing

Defroster flap - VX47- with defroster flap control motor - V107- and potentiometer for defroster flap control motor - G135- are referred to as "control motor" in the following.

Mark positions of control motors and connectors before removing in order to avoid interchanging control motors.

  • Deactivate auxiliary air conditioner function ⇒ Owner's Manual .
  • Remove dash panel ⇒ General body repairs, interior; Rep.

    gr. 70 ; Dash panel; Removing and installing dash panel .

  • Remove bolts -2-.
  • Unplug electrical connector -3-.
  • Detach control motor -1-.
Volkswagen ID.4. Removing and installing control motor for defroster flap VX47

Installing

Installation is carried out in reverse order; note the following:

  • Check position of shaft -A- relative to actuator socket -B-.

Important

  • If the splines are not aligned correctly, it will not be possible to fit the control motor -C-.
Volkswagen ID.4. Removing and installing control motor for defroster flap VX47

If a control motor has been renewed or has been installed in a different location:

  • Perform function "Adapting end stops of actuator motor flaps" ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Starting diagnosis .

Continued

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - front control motors

Removing and installing control motor for front left air distribution flap [VX93], left-hand drive vehicles

Removing

The front left air distribution flap - VX93- with front left air distribution flap control motor - V706- and potentiometer for front left air distribution flap control motor - G1105- will henceforth be referred to as "control motor".

Mark position of control motors and connectors prior to removal to avoid interchanging control motors at reinstallation.

  • Deactivate function "Stationary air conditioning" ⇒ Owner's manual .
  • Remove tunnel support cover ⇒ General body repairs, interior; Rep. gr. 70 ; Dash panel; Removing and installing tunnel support cover .
  • Remove footwell vent on driver side ⇒ Rep. gr. 87 ; Removing and installing footwell vent on driver side .
  • Raise control unit for head-up display - J898- -3- approx.

    35 mm, and support it there until control motor bolts become accessible ⇒ Electrical system; Rep. gr. 90 ; Dash panel insert; Removing and installing control unit for head-up display [J898] .

  • Unscrew bolts -2-
  • Disconnect electrical connector -4-.
  • Remove control motor -1-.
Volkswagen ID.4. emoving and installing control motor for front left air distribution flap [VX93], left-hand drive vehicles

Installing

Install in reverse order of removal, observing the following:

  • Check position of shaft -A- relative to mounting -B-.

Important

  • If teeth are not properly aligned, actuator -C- cannot be fitted.
Volkswagen ID.4. emoving and installing control motor for front left air distribution flap [VX93], left-hand drive vehicles

If control motor has been renewed or installed at different position:

  • Carry out function "Adapt flap limit stops of control motors" ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - front control motors

Removing and installing control motor for front left air distribution flap [VX93], right-hand drive vehicles

Removing

The front left air distribution flap - VX93- with front left air distribution flap control motor - V706- and potentiometer for front left air distribution flap control motor - G1105- will henceforth be referred to as "control motor".

Mark position of control motors and connectors prior to removal to avoid interchanging control motors at reinstallation.

  • Deactivate function "Stationary air conditioning" ⇒ Owner's manual .
  • Remove holder of control unit 1 for information electronics [J794] ⇒ Communication; Rep. gr. 91 ; Components/control units; Control unit 1 for information electronics [J794] .
  • Disconnect electrical connector -3-.
  • Unscrew bolts -2-.
  • Remove control motor -1-.
Volkswagen ID.4. Removing and installing control motor for front left air distribution flap [VX93], right-hand drive vehicles
  • Disconnect electrical connector -3-.
  • Unscrew bolts -2-.
  • Remove control motor -1-.

Installing

Install in the reverse sequence of removal, observing the following:

  • Check position of shaft -A- relative to mounting -B-.

Important

  • If teeth are not properly aligned, actuator -C- cannot be fitted.
Volkswagen ID.4. Removing and installing control motor for front left air distribution flap [VX93], right-hand drive vehicles

If control motor has been renewed or installed at different position:

  • Carry out function "Adapt flap limit stops of control motors" ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - front control motors

Removing and installing control motor for front right air distribution flap [VX94], left-hand drive vehicles

Removing

The front right air distribution flap - VX94- with right air distribution flap control motor - V707- and potentiometer for front right air distribution flap control motor - G1106- will henceforth be referred to as control motor.

Mark position of control motors and connectors prior to removal to avoid interchanging control motors at reinstallation.

  • Deactivate function "Stationary air conditioning" ⇒ Owner's manual .
  • Remove holder of control unit 1 for information electronics [J794] ⇒ Communication; Rep. gr. 91 ; Components/control units; Control unit 1 for information electronics [J794] .
  • Disconnect electrical connector -3-.
  • Unscrew bolts -2-
  • Remove control motor -1-.
Volkswagen ID.4. Removing and installing control motor for front right air distribution flap [VX94], left-hand drive vehicles

Installing

Install in reverse order of removal, observing the following:

  • Check position of shaft -A- relative to mounting -B-.

Important

  • If teeth are not properly aligned, actuator -C- cannot be fitted.
Volkswagen ID.4. Removing and installing control motor for front right air distribution flap [VX94], left-hand drive vehicles

If control motor has been renewed or installed at different position:

  • Carry out function "Adapt flap limit stops of control motors" ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - front control motors

Removing and installing control motor for front right air distribution flap [VX94], right-hand drive vehicles

Removing

The front right air distribution flap - VX94- with right air distribution flap control motor - V707- and potentiometer for front right air distribution flap control motor - G1106- will henceforth be referred to as control motor.

Mark position of control motors and connectors prior to removal to avoid interchanging control motors at reinstallation.

  • Deactivate function "Stationary air conditioning" ⇒ Owner's manual .
  • Remove footwell vent on driver side ⇒ Rep. gr. 87 ; Removing and installing footwell vent on driver side .
  • Disconnect electrical connector -3-.
  • Unscrew bolts -2-.
  • Remove control motor -1-.
Volkswagen ID.4. Removing and installing control motor for front right air distribution flap [VX94], right-hand drive vehicles

Installing

Install in the reverse sequence of removal, observing the following:

  • Check position of shaft -A- relative to mounting -B-.

Important

  • If teeth are not properly aligned, actuator -C- cannot be fitted.
Volkswagen ID.4. Removing and installing control motor for front right air distribution flap [VX94], right-hand drive vehicles

If control motor has been renewed or installed at different position:

  • Carry out function "Adapt flap limit stops of control motors" ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - front control motors
  • ⇒ Rep. gr. 87 ; Assembly overview - air ducts and air distribution in passenger compartment

Removing and installing control motor for fresh air and air recirculation flap [VX96]

Removing

Fresh air and air recirculation flap - VX96- with fresh air/air recirculation, air flow flap - V425- and potentiometer for fresh air/air recirculation, air flow flap control motor - G644- are referred to hereafter as control motor.

Mark position of control motors and connectors prior to removal to avoid interchanging control motors at reinstallation.

  • Deactivate function "Stationary air conditioning" ⇒ Owner's manual .
  • Remove air intake box of heater and air conditioning unit ⇒ Rep. gr. 87 ; Removing and installing air intake unit of heater and air conditioning unit .Unscrew bolts -2-.
  • Remove cover -1- in direction of -arrow-.
Volkswagen ID.4. Removing and installing control motor for fresh air and air recirculation flap [VX96]
  • Unscrew bolts -2-.
  • Disconnect electrical connector -3-.
  • Remove control motor -1-.
Volkswagen ID.4. Removing and installing control motor for fresh air and air recirculation flap [VX96]

Installing

Install in reverse order of removal, observing the following:

  • Check position of shaft -A- relative to mounting -B-.

Important

  • If teeth are not properly aligned, actuator -C- cannot be fitted.
Volkswagen ID.4. Removing and installing control motor for fresh air and air recirculation flap [VX96]

If control motor has been renewed or installed at different position:

  • Carry out function "Adapt flap limit stops of control motors" ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - front control motors

Removing and installing actuator for left air distribution flap

Removing

Mark positions of control motors and connectors before removing in order to avoid interchanging control motors.

  • Remove dash panel ⇒ General body repairs, interior; Rep.

    gr. 70 ; Dash panel; Removing and installing dash panel .

  • Remove control motor for front left temperature flap - VX34- ⇒ Rep. gr. 87 ; Removing and installing control motor for front left temperature flap VX34 .
  • Remove front left air distribution flap control motor - VX93- ⇒ Rep. gr. 87 ; Removing and installing front left air distribution flap control motor VX93 .
  • Move electrical wire clear.
  • Detach actuating lever -2-.
  • Remove bolts -3-.
  • Detach actuator for air distribution flap -1-.
Volkswagen ID.4. Removing and installing actuator for left air distribution flap

Installing

Installation is carried out in reverse order; note the following:

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - front control motors

Removing and installing right air distribution flap actuator

Removing

Mark position of control motors and connectors prior to removal to avoid interchanging control motors at reinstallation.

  • Remove dash panel ⇒ General body repairs, interior; Rep.

    gr. 70 ; Dash panel; Removing and installing dash panel .

  • Remove control motor for front right temperature flap - VX35- ⇒ Rep. gr. 87 ; Removing and installing control motor for front right temperature flap [VX35] .
  • Remove front right air distribution flap control motor - VX94- ⇒ Rep. gr. 87 ; Removing and installing front right air distribution flap control motor [VX94] .
  • Move clear electrical wire.
  • Remove actuating lever -1-.
  • Unscrew bolts -3-.
  • Remove air distribution flap actuator -2-.
Volkswagen ID.4. Removing and installing right air distribution flap actuator

Installing

Install in the reverse sequence of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - front control motors