High-voltage cables, rear-wheel drive

In this manual: High-voltage cables, rear-wheel drive
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
~10min read
0204060801005037N·mlb·ft
Tightening torque found on this page
  • Overview of fitting locations - high-voltage wires, charging unit, high-voltage battery, charging socket
  • Overview of fitting locations - high-voltage wiring, electric drive control units, high-voltage battery
  • Overview of fitting locations - high-voltage wires, voltage converter, high-voltage heater, air conditioner compressor, rear-wheel drive
  • Removing and installing high-voltage wiring harness for power and control electronics for electric drive
  • Removing and installing high-voltage wiring harness for high-voltage heater
  • Removing and installing high-voltage wiring harness for voltage converter, high-voltage heater, air conditioner compressor
  • Unplugging high-voltage connectors

Overview of fitting locations - high-voltage wires, charging unit, high-voltage battery, charging socket

Volkswagen ID.4. Overview of fitting locations - high-voltage wires, charging unit, high-voltage battery, charging socket
  1. High-voltage battery 1 - AX2-
  • Depending on equipment
  • ⇒ High-voltage battery; Rep. gr. 93 ; High-voltage battery unit; Exploded view - installed high-voltage battery
  1. High-voltage wiring harness with high-voltage battery charging socket 1 - UX4-
  • To charging unit 1 for high-voltage battery - AX4- / high-voltage battery 1 - AX2-
  • ⇒ Rep. gr. 93 ; Removing and installing high-voltage battery charging socket 1 UX4
  1. Charging unit 1 for highvoltage battery - AX4-
  • ⇒ Electric drive motor 0EH, 0EJ; Rep. gr. 93 ; Charging unit for high-voltage battery; Removing and installing charging unit 1 for high-voltage battery AX4

Overview of fitting locations - high-voltage wiring, electric drive control units, high-voltage battery

Volkswagen ID.4. Overview of fitting locations - high-voltage wiring, electric drive control units, high-voltage battery
  1. Power and control electronics 2 for electric drive - JX4-
  • Depending on vehicle equipment: vehicles with all-wheel drive
  • ⇒ Rep. gr. 93 ; Removing and installing power and control electronics 2 for electric drive JX4
  1. High-voltage battery 1 - AX2-
  • Depending on equipment
  • ⇒ High-voltage battery; Rep. gr. 93 ; Highvoltage battery unit; Assembly overview - installed high-voltage battery
  1. Power and control electronics for electric drive - JX1-
  • ⇒ Rep. gr. 93 ; Removing and installing power and control electronics for electric drive JX1
  1. High-voltage wiring harness for power and control electronics for electric drive - JX1-
  • Depending on equipment
  • ⇒ Rep. gr. 93 ; Removing and installing high-voltage wiring harness for power and control electronics, rear-wheel drive
  1. High-voltage wiring harness for power and control electronics for electric drive - JX1- and power and control electronics 2 for electric drive - JX4-
  • Depending on vehicle equipment: vehicles with all-wheel drive
  • ⇒ Rep. gr. 93 ; Removing and installing high-voltage wiring harness for power and control electronics, all-wheel drive
  1. Passage
  • ⇒ "23.4 Assembly overview - passage"

Overview of fitting locations - high-voltage wires, voltage converter, high-voltage heater, air conditioner compressor, rear-wheel drive

Volkswagen ID.4. Overview of fitting locations - high-voltage wires, voltage converter, high-voltage heater, air conditioner compressor, rear-wheel drive
  1. PTC heater element 3 - Z132-
  • ⇒ Heating, air conditioning; Rep. gr. 87 ; Coolant circuit; Removing and installing heater element 3 Z132
  1. Electrical air conditioner compressor - V470-
  • ⇒ Heating, air conditioning; Rep. gr. 87 ; Air conditioner compressor; Removing and installing air conditioner compressor VX81
  1. High-voltage wire to highvoltage heater (PTC) - ZX17-
  • ⇒ "23.6 Removing and installing high-voltage wiring harness for highvoltage heater"
  1. High-voltage heater (PTC) - ZX17-
  • ⇒ Heating, air conditioning; Rep. gr. 87 ; Front heater and air conditioning unit; Removing and installing high-voltage heater (PTC) ZX17
  1. Charging unit 1 for highvoltage battery - AX4-
  • ⇒ Rep. gr. 93 ; Assembly overview - charging unit for highvoltage battery, rearwheel drive
  1. High-voltage wiring harness for ancillaries
  • ⇒ "24.3 Overview of fitting locations - high-voltage wires, voltage converter, high-voltage heater, air conditioner compressor, rear-wheel drive"
  1. High-voltage battery 1 - AX2-
  • Depending on equipment
  • ⇒ High-voltage battery; Rep. gr. 93 ; High-voltage battery unit; Assembly overview - installed highvoltage battery
  1. Passage
  • ⇒ "23.4 Assembly overview - passage"
  1. Voltage converter - A19-
  • ⇒ Rep. gr. 93 ; Assembly overview - voltage converter

Assembly overview - passage

Volkswagen ID.4. Assembly overview - passage
  1. Bolt
  • 2x
  • 50 N·m + 90º
  1. Passage
  • Front section
  1. Passage
  • Rear section
  1. Bolt
  • 2x
  • 8 N·m
  1. Bolt
  • 2x
  • 20 N·m
  1. Bolt
  • 20 N·m
  1. Bracket
  • For passage

Removing and installing high-voltage wiring harness for power and control electronics for electric drive

Removing

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) de-energise the high-voltage system.
  • ⇒ Rep. gr. 93 ; De-energise high-voltage system .
  • Disconnect high-voltage system connection -4- ⇒ Rep. gr. 93 ; Disconnecting high-voltage connectors .
Volkswagen ID.4. Removing and installing high-voltage wiring harness for power and control electronics for electric drive
  • Open spreader rivet -2-, and release high-voltage cable retainer -3-.
Volkswagen ID.4. Removing and installing high-voltage wiring harness for power and control electronics for electric drive
  • Remove electric drive motor for rear axle ⇒ Rep. gr. 10 ; Removing rear motor .
  • Lower rear axle ⇒ Running gear, axles, steering; Rep.gr. 42 ; Rear axle; Lowering rear axle .
  • Move aside high-voltage cable of electric drive motor -1-, and guide it through towards front.
  • Detach high-voltage cable -1-.
Volkswagen ID.4. Removing and installing high-voltage wiring harness for power and control electronics for electric drive

Installing

Install in reverse order of removal, observing the following:

WARNING

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) re-energise the high-voltage system.
  • ⇒ Rep. gr. 93 ; Re-energise high-voltage system .

Tightening torques

  • ⇒ "23.4 Assembly overview - passage"
  • ⇒ Rep. gr. 19 ; Assembly overview - electric coolant pump

Removing and installing high-voltage wiring harness for high-voltage heater

Removing

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) de-energise the high-voltage system.
  • ⇒ Rep. gr. 93 ; De-energise high-voltage system .
  • Remove bulkhead ⇒ General body repairs, exterior; Rep.gr. 50 ; Bulkhead; Removing and installing bulkhead .Remove air intake box of heater and air conditioning unit ⇒ Heating, air conditioning system; Rep. gr. 87 ; Front heater and air conditioning unit; Removing and installing air intake box of heater and air conditioning unit .Disconnect high-voltage connectors -3- ⇒ Rep. gr. 93 ; Disconnecting high-voltage connectors .
  • Loosen cable holders -arrows- on bulkhead.
  • Expose high-voltage cable -2- as far as leadthrough -1-.
Volkswagen ID.4. Removing and installing high-voltage wiring harness for high-voltage heater
  • Remove front right footwell vent ⇒ Heating, air conditioning system; Rep. gr. 87 ; Air duct; Assembly overview - air duct and air distribution in passenger compartment .
  • Disconnect electrical connector -7-, and loosen retaining clip -5-.
  • Expose high-voltage cable as far as leadthrough.
Volkswagen ID.4. Removing and installing high-voltage wiring harness for high-voltage heater
  • Release fasteners -6- of grommet -5-.
  • Guide high-voltage cable -7- out of air intake cowling -4-.
  • Unscrew bolts -1- and -3-.
Volkswagen ID.4. Removing and installing high-voltage wiring harness for high-voltage heater
  • Remove high-voltage cable -2- upwards.
Volkswagen ID.4. Removing and installing high-voltage wiring harness for high-voltage heater

Installing

Install in reverse order of removal, observing the following:

WARNING

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) re-energise the high-voltage system.
  • ⇒ Rep. gr. 93 ; Re-energise high-voltage system .

Removing and installing high-voltage wiring harness for voltage converter, high-voltage heater, air conditioner compressor

Removing

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) de-energise the high-voltage system.
  • ⇒ Rep. gr. 93 ; De-energise high-voltage system .
  • Remove air intake box of heater and air conditioning unit ⇒ Heating, air conditioning system; Rep. gr. 87 ; Front heater and air conditioning unit; Removing and installing air intake box of heater and air conditioning unit .
  • Remove PTC heater element 3 - Z132- ⇒ ; Rep. gr. ; Removing and installing PTC heater element 3 [Z132] .
  • Disconnect upper of electrical connectors indicated by -2-, and move aside cables ⇒ Electric drive motor; Rep. gr. 93 ; High-voltage cables; Disconnecting high-voltage connectors .
Volkswagen ID.4. Removing and installing high-voltage wiring harness for voltage converter, high-voltage heater, air conditioner compressor
  • Disconnect high-voltage connectors -3- ⇒ Rep. gr. 93 ; Disconnecting high-voltage connectors .
Volkswagen ID.4. Removing and installing high-voltage wiring harness for voltage converter, high-voltage heater, air conditioner compressor
  • Disconnect high-voltage electrical connector -3- from voltage converter.
  • Move aside high-voltage cable leading to voltage converter.
Volkswagen ID.4. Removing and installing high-voltage wiring harness for voltage converter, high-voltage heater, air conditioner compressor

For reasons of clarity, the following work procedures are shown with the subframe -4- removed.

  • Pull off retaining clip -8-, and move aside high-voltage cable at subframe.
  • Move aside high-voltage cable at subframe, and guide it through towards rear.
Volkswagen ID.4. Removing and installing high-voltage wiring harness for voltage converter, high-voltage heater, air conditioner compressor
  • Remove front underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing front underbody cladding .
  • Unscrew bolts -1- for coolant pump bracket.
  • Pull corresponding electrical wire -arrow- off retainer.
Volkswagen ID.4. Removing and installing high-voltage wiring harness for voltage converter, high-voltage heater, air conditioner compressor
  • Remove high-voltage battery; do not reattach passage ⇒ High-voltage battery; Rep. gr. 93 ; High-voltage battery unit; Removing and installing high-voltage battery 1 [AX2] .
  • Unscrew bolts -4- and -5-.
  • Remove support plate -3-.
  • Unscrew bolts -2- and -6-.
  • Remove support plate -1-.
Volkswagen ID.4. Removing and installing high-voltage wiring harness for voltage converter, high-voltage heater, air conditioner compressor
  • Open spreader rivet -2-, and release high-voltage cable retainer -3-.
  • Unscrew bolts -arrows-, and pull passage -1- downwards slightly.
  • Unclip high-voltage cable -5-, and guide it through towards rear.
Volkswagen ID.4. Removing and installing high-voltage wiring harness for voltage converter, high-voltage heater, air conditioner compressor
  • Secure media duct -1- with screws -2- ⇒ Electronic parts catalogue (ETKA) .
Volkswagen ID.4. Removing and installing high-voltage wiring harness for voltage converter, high-voltage heater, air conditioner compressor
  • Remove electric drive motor for rear axle ⇒ Rep. gr. 10 ; Removing rear motor .
  • Lower rear axle ⇒ Running gear, axles, steering; Rep.gr. 42 ; Rear axle; Lowering rear axle .
  • Push high-voltage cable of electric drive motor -1- to one side.
  • Unscrew nuts -arrows-, and push wiring duct -3- to one side.
  • Move aside high-voltage cable -2-.
Volkswagen ID.4. Removing and installing high-voltage wiring harness for voltage converter, high-voltage heater, air conditioner compressor
  • Loosen cable clips -arrows-.
  • Push electrical wire -1- to one side.
  • Move aside high-voltage cable -2-, and guide it through towards front.
  • Remove high-voltage cable for ancillaries.
Volkswagen ID.4. Removing and installing high-voltage wiring harness for voltage converter, high-voltage heater, air conditioner compressor

Installing

Install in reverse order of removal, observing the following:

WARNING

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) re-energise the high-voltage system.
  • ⇒ Rep. gr. 93 ; Re-energise high-voltage system .

Tightening torques

  • ⇒ "23.4 Assembly overview - passage"
  • ⇒ Rep. gr. 19 ; Assembly overview - electric coolant pump

Unplugging high-voltage connectors

Version 1 for electrical connector of auxiliary consumers

  • Release locking element -1- in direction of -arrow A-.
  • Insert a suitable screwdriver -5- between locking element -1- and electrical connector for auxiliary consumers -3- to release and disconnect electrical connector in direction of -arrow B-.
Volkswagen ID.4. Unplugging high-voltage connectors

All vehicles (continued)

Version 2 for electrical connector of auxiliary consumer

  • Release locking element -1- in direction of -arrow A-.
  • Using a suitable screwdriver -5-, release electrical connector for auxiliary consumers -2- in direction of -arrow B- and disconnect.
Volkswagen ID.4. Unplugging high-voltage connectors

All vehicles (continued)

Version 1 for electrical connector of high-voltage system connection/ DC charging connection

  • Release locking element -3- by turning it in direction of -arrow A-.
  • Press locking bracket -4- in direction of -arrow B-, and disconnect high-voltage system connection -1- and DC charging connection -1-.
Volkswagen ID.4. Unplugging high-voltage connectors

All vehicles (continued)

Version 2 for electrical connector of high-voltage system connection/ DC charging connection

  • Use suitable screwdriver to release locking element -2- by pushing it upwards.
  • Release locking element -2- in direction of -arrow A-.
  • Press locking bracket -4- in direction of -arrow B-, and disconnect high-voltage system connection -1- and DC charging connection -1-.
Volkswagen ID.4. Unplugging high-voltage connectors