Bumper, rear

In this manual: Bumper, rear
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
5steps
~30min
2/5difficulty
0102030405032N·mlb·ft
Tightening torque found on this page
Done 0 of 5
  • Assembly overview - bumper cover
  • Assembly overview - attachments
  • Removing and installing bumper cover
  • Removing and installing base plate for bumper cover
  • Removing and installing bottom section of bumper cover
  • Installing holder for park assist steering sender
  • Installing number plate
  • Removing and installing forced ventilation for passenger compartment

Assembly overview - bumper cover

Volkswagen ID.4. Assembly overview - bumper cover
  1. Dampers
  2. Guide profile
  3. Bolt
  • Qty. 12
  • 3 N·m
  1. Expansion nut
  • Qty. 12
  1. Guide profile
  2. Forced ventilation for passenger compartment
  • ⇒ Rep. gr. 63 ; Removing and installing forced ventilation for passenger compartment
  • ⇒ Rep. gr. 63 ; Checking forced ventilation for passenger compartment
  1. Expansion nut
  • Qty. 4
  1. Expansion nut
  • Qty. 4
  1. Bumper cover
  • ⇒ Rep. gr. 63 ; Removing and installing bumper cover
  • ⇒ Rep. gr. 63 ; Repairing bumper cover
  1. Bolt
  • Qty. 4
  • 2 N·m
  1. Bolt
  • Qty. 4
  • 2 N·m
  1. Spreader rivet
  • Qty. 2

Assembly overview - bumper carrier

  1. Bumper carrier
  • ⇒ Rep. gr. 63 ; Removing and installing bumper carrier
  1. Bolt
  • Qty. 7
  • 20 N·m
Volkswagen ID.4. Assembly overview - bumper carrier

Assembly overview - attachments

Volkswagen ID.4. Assembly overview - attachments
  1. Holder for park assist steering sender
  • Left
  • ⇒ Rep. gr. 63 ; Installing holder for park assist steering sender
  1. Bumper cover upper part
  • Left
  • ⇒ Rep. gr. 63 ; Removing and installing top section of bumper cover
  1. Bumper cover lower part
  • ⇒ Rep. gr. 63 ; Removing and installing bottom section of bumper cover
  1. Bumper cover upper part
  • Right
  • ⇒ Rep. gr. 63 ; Removing and installing top section of bumper cover
  1. Holder for park assist steering sender
  • Right
  • ⇒ Rep. gr. 63 ; Installing holder for park assist steering sender
  1. Rear fog light - X3-
  • Right-hand drive vehicles
  • ⇒ Electrical system; Rep. gr. 94 ; Tail lights; Removing and installing rear fog light [X3]
  1. Towing eye cap
  • Depending on equipment/installation period
  • ⇒ Rep. gr. 63 ; Removing and installing towing eye cap
  1. Bumper cover trim
  • Depending on equipment/installation period
  • ⇒ Rep. gr. 63 ; Removing and installing bumper cover trim
  1. Rear lid power opening control unit - J938-
  • Depending on equipment/installation period
  • ⇒ Rep. gr. 55 ; Removing and installing rear lid power opening control unit [J938]
  1. Holder for rear lid power opening control unit - J938-
  • Depending on equipment/installation period
  • ⇒ Rep. gr. 55 ; Removing and installing holder for rear lid power opening control unit [J938]
  1. Base plate for bumper cover
  • Depending on equipment/installation period
  • ⇒ Rep. gr. 63 ; Removing and installing base plate for bumper cover
  1. Rear lid power opening sender - G750- / rear lid power opening sender 2 - G760-
  • Depending on equipment/installation period
  • ⇒ Rep. gr. 55 ; Removing and installing rear lid power opening sender [G750]/[G760]
  1. Rear fog light - X3-
  • Left-hand drive vehicles
  • ⇒ Electrical system; Rep. gr. 94 ; Tail lights; Removing and installing rear fog light [X3]

Removing and installing bumper cover

Special tools and workshop equipment required

  • setting gauge - 3371-

Removing

Vehicles with hinged towing bracket - VX15- .

  • Swing in towing bracket.

All vehicles (continued)

Vehicles with removable towing bracket and mounting for trailer coupling ball head.

  • Unscrew bolt.
  • Remove mounting for trailer coupling ball head.
Volkswagen ID.4. Removing and installing bumper cover

All vehicles (continued)

  • Remove left tail light cluster - MX3- and right tail light cluster - MX4- ⇒ Electrical system; Rep. gr. 94 ; Tail light clusters; Removing and installing tail light cluster [MX3]/[MX4] .
  • Detach rear wheel housing liners in area of bumper cover ⇒ Rep. gr. 66 ; Removing and installing rear wheel housing liner .
  • Detach rear wheel arch covers in area of bumper cover ⇒ Rep. gr. 66 ; Removing and installing rear wheel arch cover .
  • Unscrew bolts -1- on both sides of vehicle.
Volkswagen ID.4. Removing and installing bumper cover
  • Remove spreader rivets -1- on both sides of vehicle.
Volkswagen ID.4. Removing and installing bumper cover

Important

  • A second person is required for the following steps.
  • Unclip bumper cover -1- in direction of -arrow A- from guide, and hold it there.
  • Pull off bumper cover -1- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing bumper cover
  • Disconnect electrical connector -2- of rear fog light - X3- -1-.
  • Disconnect electrical connectors -3- of rear left parking aid sender - G203- , rear centre left parking aid sender - G204- , rear centre right parking aid sender - G205- and rear right parking aid sender - G206- -4-.
Volkswagen ID.4. Removing and installing bumper cover

Vehicles with rear left park assist steering sender - G716- / rear right park assist steering sender - G717-

  • Disconnect electrical connectors of rear left park assist steering sender - G716- and rear right park assist steering sender - G717- .

All vehicles (continued)

Installing

Install in reverse order of removal, observing the following:

New bumper cover for vehicles with rear lid power opening control unit - J938-

  • Install rear lid power opening control unit - J938- ⇒ Rep. gr. 55 ; Rear lid power opening control unit [J938] .

All vehicles (continued)

  • Verify gaps using setting gauge - 3371- . Observe ⇒ Rep. gr. 00 ; Gaps - rear when doing this.

Tightening torques

  • ⇒ Rep. gr. 63 ; Assembly overview - bumper cover

Vehicles with removable towing bracket

  • ⇒ Rep. gr. 66 ; Assembly overview - towing bracket

Repairing bumper cover

Before the bumper cover is repaired, it must be determined whether repair is possible or whether the bumper cover must be renewed.

Observe notes and work instructions ⇒ General Information; Body Repairs, General Body Repairs ; Plastic repair procedures .

Removing and installing bumper carrier

Removing

  • Remove bumper cover ⇒ Rep. gr. 63 ; Removing and installing bumper cover .
  • Unscrew bolts -2-.
  • Lift bumper carrier -1- with guides -4- in direction of -arrowout of tabs -3-, and remove it.
Volkswagen ID.4. Removing and installing bumper carrier

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 63 ; Assembly overview - bumper carrier

Removing and installing base plate for bumper cover

Removing

  • Remove bumper cover trim ⇒ Rep. gr. 63 ; Removing and installing bumper cover trim .
  • Free off electrical lines.
  • Loosen fasteners -2- along entire width.
  • Pull off base plate for bumper cover -1- with centring pin -3- in direction of -arrow- from bottom section of bumper cover -4-.
Volkswagen ID.4. Removing and installing base plate for bumper cover

Installing

Install in reverse order of removal, observing the following:

  • Insert centring pin into recess.

Removing and installing base plate for bumper cover, GTX

Removing and installing base plate for bumper cover

Removing

  • Remove bumper cover ⇒ Rep. gr. 63 ; Removing and installing bumper cover .
  • Free off electrical lines.
  • Loosen fasteners -2- along entire width.
  • Pull base plate for bumper cover -1- in direction of -arrowoff bottom section of bumper cover -3-.
Volkswagen ID.4. Removing and installing base plate for bumper cover

Installing

Install in reverse order.

Removing and installing top section of bumper cover

Removing

  • Remove bumper cover ⇒ Rep. gr. 63 ; Removing and installing bumper cover .
  • Move electrical wiring aside.
  • Detach fasteners -2- on both sides of vehicle.
  • Pull top section of bumper cover -1- in direction of -arrow- off bumper cover -3-.
Volkswagen ID.4. Removing and installing top section of bumper cover

Installing

Install in reverse order of removal.

Removing and installing bottom section of bumper cover

Removing

  • Remove top section of bumper cover ⇒ Rep. gr. 63 ; Removing and installing top section of bumper cover .
  • Loosen fasteners -arrows- along entire width.
  • Pull bottom section of bumper cover -1- off base plate for bumper cover -2-.
Volkswagen ID.4. Removing and installing bottom section of bumper cover

Installing

Install in reverse order of removal.

Removing and installing bumper cover trim

Removing

  • Remove rear bumper cover ⇒ Rep. gr. 63 ; Removing and installing bumper cover .
  • Loosen fasteners -2- along entire width.
  • Pull bumper cover trim -1- off bumper cover -3-.
Volkswagen ID.4. Removing and installing bumper cover trim

Installing

Install in reverse order of removal.

Installing holder for park assist steering sender

Special tools and workshop equipment required

  • drill bit - VAS 6614/4-
  • screw-hole punch, 26.5 mm - VAS 895 003-

Installing

Holder for park assist steering sender is referred to hereafter as holder.

The installation is described for one of the holders as an example.

The holder is installed after the bumper cover has been painted.

Important

  • Components, adhesive and primer must have adjusted to room temperature.
  • Observe specifications with regard to temperature, minimum curing period, removal of adhesive residue and cleaning ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for self-adhesive components .

Markings -1- for bracket are located on inside of bumper cover -1-.

  • Predrill hole using drill bit - VAS 6614/4- -3-.
Volkswagen ID.4. Installing holder for park assist steering sender
  • Fit screw-hole punch, 26.5 mm - VAS 895 003- -2- with screw head, washer and counter-support -1- from inside of bumper cover -3-.
  • Screw on punch -4- until just before bumper cover -3-.
  • Press punch -4- against bumper cover -3-.
  • Tighten bolt head -1-.

NOTICE

Risk of damage to component surfaces due to turning the screw-hole punch.

  • Hold the screw-hole punch firmly.
Volkswagen ID.4. Installing holder for park assist steering sender
  • Turn screw head -1- to pull punch -4- in direction of -arrowthrough material of bumper cover -3-.
  • Release screw-hole punch 26.5 mm -2- from bumper cover -3-.

Note

Markings for correct position of bracket -1- are on inside of bumper cover -2-.

  • Align bracket.
  • Pull protective film off adhesive tape.
  • Attach holder -1- in direction of -arrow A- in bumper cover -2-.
  • Press retainer -1- forcefully against bonding surface.

Important

  • Do not carry out any further work on bumper cover or brackets until minimum curing period of 2 hours at 23ºC has expired.
Volkswagen ID.4. Installing holder for park assist steering sender

Installing number plate

Installing

  • Align number plate -1- between left number plate light - X4- and right number plate light - X5- -arrows-.
  • Make sure that number plate -1- is properly aligned with upper recess.
  • Make sure that outer edges of number plate -1- are properly aligned with outer edges of left number plate light - X4- and right number plate light - X5- -arrows-.
  • Mark positions of holes for number plate -1- on bumper cover -2-.
  • Secure number plate -1- to bumper cover -2- using thread cutting screws.
Volkswagen ID.4. Installing number plate

Removing and installing towing eye cap

Removing and installing towing eye cap, two-piece

The two-piece towing eye cap will henceforth be referred to as "cap".

Removing

  • Press cap -1- in area of -arrow-, and release it.
  • Detach cap -1-, and guide out tether -2-.
  • Remove cap -1-.
Volkswagen ID.4. Removing and installing towing eye cap, two-piece

Installing

Install in reverse order of removal, observing the following:

  • Insert cap into recess, and press it on until fastener can be heard to engage

Removing and installing towing eye cap, GTX

Removing and installing towing eye cap, one-piece

The one-piece towing eye cap will henceforth be referred to as "cap".

Shape of cap varies depending on model.

Removing

  • Press cap -1- in area of -arrow-, and release it.
  • Detach cap -1-, and guide out tether -2-.
  • Remove cap -1-.
Volkswagen ID.4. Removing and installing towing eye cap, one-piece

Installing

Install in reverse order of removal, observing the following:

  • Insert cap into recess, and press it on until fastener can be heard to engage.

Dismantling and assembling towing eye cap, two-piece, GTX

Dismantling and assembling towing eye cap, two-piece

The two-piece towing eye cap will henceforth be referred to as "cover".

Dismantling

  • Remove two-piece towing eye cap ⇒ Rep. gr. 63 ; Removing and installing towing eye cap,GTX .
  • Release fastener -2-.
  • Swing lower section of cover -3- in direction of -arrow A- out of upper section of cover -1-, and detach it in direction of -arrow B-.
Volkswagen ID.4. Dismantling and assembling towing eye cap, two-piece

Assembling

Assemble in reverse order of dismantling.

Removing and installing forced ventilation for passenger compartment

Removing

  • Remove bumper cover ⇒ Rep. gr. 63 ; Removing and installing bumper cover .
  • Release locking devices -arrows- using commercially available plastic wedge.
  • Remove forced ventilation for passenger compartment -1-.
Volkswagen ID.4. Removing and installing forced ventilation for passenger compartment

Installing

Install in reverse order.

Checking forced ventilation for passenger compartment

Forced ventilation for the passenger compartment is located in the side panels, behind the bumper cover.

  • Remove bumper cover ⇒ Rep. gr. 63 ; Removing and installing bumper cover .

Important

  • The ventilation openings must not be covered.
  • The sealing lips in the forced ventilation for passenger compartment must be free to move and close autonomously.