Removing and installing rear motor

In this manual: Removing and installing rear motor
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
22steps
~132min
4/5difficulty
0102030405086N·mlb·ft
Tightening torque found on this page
Done 0 of 22
  • Assembly overview - rear motor
  • Removing rear motor
  • Securing motor to engine and gearbox support, rear motor
  • Installing rear motor

Assembly overview - rear motor

  1. Electrical connector
  • High voltage
  1. Wiring guide
  2. Bolt
  • Qty. 6
  • 8 N·m
  1. O-ring
  2. Retaining clip
  3. Coolant hose
  4. Clip
  5. Clamp
  6. Bolt
  • Qty. 2
  • Renew after removing
  • 8 N·m +90º
  1. O-ring
  • Renew after removing
  1. Union
  2. Three-phase current drive - VX54-
  • With power and control electronics for electric drive - JX1-
  • ⇒ Rep. gr. 93 ; Removing and installing power and control electronics for electric drive
  • ⇒ Rep. gr. 10 ; Removing rear motor
  • ⇒ Rep. gr. 10 ; Installing rear motor
  1. Coolant pipe
  • To remove, remove high-voltage battery ⇒ Rep. gr. 93 ; High-voltage battery unit
  1. O-ring
  2. Bleeder valve
  • Special lubricant for sealing seat ⇒ Electronic parts catalogue (ETKA)
  • Renew after removing
  1. Bolt
  • Qty. 2
  • Renew after removing
  • 130 N·m +180º
  1. Bolt
  • Qty. 3
  • Renew after removing
  • 70 N·m +180º
  1. Engine support
  2. Bolt
  • Renew after removing
  • 130 N·m +180º
  1. Temperature sensor - G18-
  • ⇒ Rep. gr. 19 ; Removing and installing temperature sensor [G18]
  1. O-ring
  • Renew after removing
  1. Coolant hose
  2. Retainer
  • Contact point for potential equalisation line
  • Secured to centre hex stud
  • Centre hex stud: 8 N·m +45º
  1. Nut
  • 8 N·m
  1. O-ring
  2. Breather line
  3. Bolt
  • 8 N·m
  1. Electrical connector
Volkswagen ID.4. Assembly overview - rear motor

Removing rear motor

Special tools and workshop equipment required

  • Hook - 3282/049-
  • Pin - 3282/34-
  • Pin - 3282/45-
  • bit XZN 16 - T10198-
  • engine and gearbox jack - VAS 6931-
  • engine bung set - VAS 6122-
  • gearbox support - 3282-

Three-phase current drive - VX54- with power and control electronics for electric drive - JX1- is referred to hereafter as motor.

Removing

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) de-energise the high-voltage system.
  • ⇒ Rep. gr. 93 ; De-energise high-voltage system .
  • Remove rear centre underbody cladding -1- ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing rear centre underbody cladding .
  • Remove rear underbody cladding -2- ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing rear underbody cladding .
  • Remove stone deflector for spring control arm -4- ⇒ Running gear, axles, steering; Rep. gr. 42 ; Suspension link, track rod; Removing and installing stone deflector for spring control arm .
Volkswagen ID.4. Removing rear motor
  • Remove left and right drive shaft ⇒ Running gear, axles, steering; Rep. gr. 42 ; Drive shaft; Removing and installing drive shaft .
  • Remove rear left and right wheel housing liner ⇒ General body repairs, exterior; Rep. gr. 66 ; Wheel housing liner; Removing and installing rear wheel housing liner .
  • ⇒ Rep. gr. 19 ; Drain coolant .

Note

For the bolt of the gearbox mounting to be renewed it is necessary to remove the charger.

  • Remove charging unit 1 for high-voltage battery - AX4- ⇒ Rep. gr. 93 ; Removing and installing charging unit 1 for high-voltage battery [AX4] .
  • Open hose clip -arrow-, and pull off coolant hose -1-.
  • Disconnect electrical connector -2-.
Volkswagen ID.4. Removing rear motor
  • Unscrew nut -arrow-, and remove bracket -1- for potential equalisation line.
Volkswagen ID.4. Removing rear motor
  • Unclip coolant hose -1- as shown -arrow-.
Volkswagen ID.4. Removing rear motor
  • Unclip gearbox breather line -1- in rear left wheel housing -arrows-.
Volkswagen ID.4. Removing rear motor
  • On gearbox side, unscrew bolts -arrows- for high-voltage cable duct -1-.
Volkswagen ID.4. Removing rear motor
  • Place gearbox support - 3282- -D- on engine and gearbox jack - VAS 6931- -E-.
  • Position engine and gearbox jack -E- centrally under motor and gearbox -2-.
  • Screw in adapters into supports as follows:
  1. Pin - 3282/34-
  2. Pin - 3282/45- with screwed on nut -1-
  3. Hook - 3282/049-
  • Align mountings -A- and -B- to mounting points in motor and gearbox.
  • Position mounting -C- under power and control electronics for electric drive - JX1- .
  • Raise motor with gearbox to relieve load on motor mountings.
Volkswagen ID.4. Removing rear motor
  • Use bit XZN 16 - T10198- to unscrew bolts -1- for left and right motor mountings through opening -arrow- in longitudinal member.
Volkswagen ID.4. Removing rear motor
  • Unscrew gearbox mounting bolt -arrow-.
Volkswagen ID.4. Removing rear motor
  • Lower motor with gearbox approx. 150 mm
Volkswagen ID.4. Removing rear motor
  • Detach high-voltage cable -1- from power and control electronics for electric drive - JX1- . To do this, unscrew bolts -2- and -3- above the gearbox.
  • Open locking bracket -A- on high-voltage connector -4-, and pull off high-voltage connector ⇒ Rep. gr. 93 ; Disconnecting high-voltage connectors .
Volkswagen ID.4. Removing rear motor
  • Unclip coolant hose -1- above gearbox -arrow A-.
  • Lift catch -2- and pull off coolant hose.
  • Unclip gearbox breather line -3- -arrow B-, and pull it off gearbox.

NOTICE

Risk of damage to lines and hoses when lowering the motor/ gearbox assembly.

  • Make sure that all connections between the motor/gearbox and the vehicle body have been disconnected.
  • When lowering, carefully guide motor/gearbox assembly out of motor compartment.
  • Lower motor with gearbox.
  • Seal any open connections on motor and gearbox with plugs from engine bung set - VAS 6122- .

Securing motor to engine and gearbox support, rear motor

Special tools and workshop equipment required

  • Motor bracket - VAS 6095A/1-21-
  • engine and gearbox support - VAS 6095A-
  • lifting tackle - VAS 501 019-
  • retaining plate - VW309A-
  • workshop hoist - VAS 6100-

CAUTION

Risk of injury from moving parts.

Body parts could suffer contusions.

  • Never reach or step into the hazard zone.

Assembling lifting tackle - VAS 501 019- -A-

  • Fit bow - VAS 501 019/1- -1- and bow - VAS 501 019/2- -2- to lifting tackle. Screw in bolts -5-.
  • Secure shackle -4- in hole shown in illustration.
Volkswagen ID.4. Securing motor to engine and gearbox support, rear motor
  • Align bows -1- and -2- with markings -arrows-.
  • Tighten bolts -5-.
Volkswagen ID.4. Securing motor to engine and gearbox support, rear motor

Securing motor on engine and gearbox support

  • Insert bows -1- and -2- of lifting tackle -A- into holes -arrows B-.
  • Screw bolt -3- by hand to stop into hole -arrow C-.
  • Attach workshop hoist - VAS 6100- to shackle -4-, and raise motor.
Volkswagen ID.4. Securing motor to engine and gearbox support, rear motor
  • Mount motor bracket - VAS 6095A/1-21- -A- on retaining plate - VW309A- -B- and tighten bolts.
  • Position motor bracket -A- on motor -1-, and tighten bolts.
Volkswagen ID.4. Securing motor to engine and gearbox support, rear motor
  • Secure motor -1- with motor bracket -A- and support plate -B- to engine and gearbox support - VAS 6095A- -C-.
Volkswagen ID.4. Securing motor to engine and gearbox support, rear motor

Installing rear motor

Special tools and workshop equipment required

  • bit XZN 16 - T10198-
  • engine and gearbox jack - VAS 6931-
  • gearbox support - 3282-

Three-phase current drive - VX54- with power and control electronics for electric drive - JX1- is referred to hereafter as motor.

Installing

Important

  • Motor and gearbox are secured to gearbox support - 3282- and engine and gearbox jack - VAS 6931- ⇒ Rep. gr. 10 ; Removing rear motor .
  • Raise motor with gearbox -1- up to 150 mm before installation position.
Volkswagen ID.4. Installing rear motor
  • Fit electrical connector -1- above gearbox, and close locking bracket in direction of -arrow A-.
  • Tighten bolts -2- and -3-.
Volkswagen ID.4. Installing rear motor
  • Fit coolant hose -1- above gearbox, and close locking element -2-. Ensure proper engagement by pulling.
  • Attach breather line -3-.
  • Close clips -arrow A- and -arrow B-.
Volkswagen ID.4. Installing rear motor
  • Raise motor with gearbox -1- until bolts for motor and gearbox mountings can be started.
  • Tighten bolts for engine and gearbox mounting using bit XZN 16 - T10198- .
Volkswagen ID.4. Installing rear motor
  • Mount bracket -1- for potential equalisation line on gearbox and tighten nut -arrow-.
Volkswagen ID.4. Installing rear motor
  • Install left and right drive shafts ⇒ Running gear, axles, steering; Rep. gr. 42 ; Drive shaft; Removing and installing drive shaft .

If the power and control electronics for electric drive - JX1- has been renewed:

  • Carry out function "power and control electronics for electric drive [JX1], commissioning" ⇒ Rep. gr. 00 ; Access to diagnoses .

Note

At the end of the diagnosis, the function "Calibrate electric drive motor" is carried out automatically.

Continued

If the three-phase current drive - VX54- was renewed:

  • Carry out function "Calibrate electric drive motor" ⇒ Rep.

    gr. 93 ; Calibrating electric drive motor [VX54] .

Continued

Further installation is carried out in reverse order of removal, observing the following:

WARNING

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) re-energise the high-voltage system.
  • ⇒ Rep. gr. 93 ; Re-energise high-voltage system

Tightening torques

  • ⇒ Rep. gr. 10 ; Assembly overview - motor
  • ⇒ Rep. gr. 93 ; Assembly overview - electric drive motor, rear motor
  • ⇒ Rep. gr. 93 ; Assembly overview - charging unit for high-voltage battery
  • ⇒ Running gear, axles, steering; Rep. gr. 42 ; Drive shaft; Assembly overview - drive shaft
  • ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Assembly overview - underbody cladding