Front seats

In this manual: Front seats
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
39steps
~234min
4/5difficulty
0204060801004030N·mlb·ft
Tightening torque found on this page
Done 0 of 39
  • Overview of fitting locations electrical and electronic components
  • Assembly overview front seat
  • Assembly overview - front backrest
  • Assembly overview - head restraint
  • Assembly overview seat pan
  • Assembly overview seat height adjustment
  • Assembly overview lumbar support
  • Removing and installing front seat
  • Removing and installing trim for backrest with integrated head restraint
  • Removing and installing seat height adjuster
  • Removing and installing head restraint
  • Removing and installing head restraint
  • Removing and installing head restraint guide
  • Removing and installing lumbar support adjustment switch [E176]/[E177]
  • Removing and installing lumbar support
  • Removing and installing bracket for seat trim
  • Removing and installing outer seat trim
  • Removing and installing seat depth adjuster
  • Removing and installing seat adjustment control unit
  • Removing and installing wiring harness for seat frame

Overview of fitting locations electrical and electronic components

Overview of fitting locations - electrical and electronic components

Overview shown for left side of vehicle as an example

  1. Inner side airbag, driver side
  • With igniter for central airbag for occupant collision protection, driver side - N737-
  • Fitted on driver side
  • ⇒ Rep. gr. 69 ; Assembly overview - front side airbag, inner side
  • ⇒ Rep. gr. 69 ; Removing and installing front side airbag, inner side
  1. Backrest heating element
  • With heated backrest for front left seat - Z116- or heated backrest for front right seat - Z117-
  • Depending on equipment/ version
  • ⇒ Rep. gr. 74 ; Removing and installing backrest heating element [Z116]/[Z117]
  1. Lumbar support
  2. Depending on equipment/ version
  • Cannot be renewed individually
  • ⇒ Rep. gr. 72 ; Removing and installing lumbar support
  1. Front side airbag, outer side
  • With side airbag igniter on driver side - N199- or side airbag igniter on front passenger side - N200-
  • ⇒ Rep. gr. 69 ; Assembly overview - front side airbag, outer side
  • ⇒ Rep. gr. 69 ; Removing and installing front side airbag, outer side
  1. Compressor for multicontour driver seat - V439- / compressor for multicontour front passenger seat - V440-
  • Depending on equipment/version
  • Cannot be renewed individually
  • ⇒ Rep. gr. 72 ; Removing and installing lumbar support
  1. Seat height adjuster
  • With driver seat height adjustment motor - V245- or front passenger seat height adjustment motor - V246-
  • Depending on equipment/version
  • ⇒ Rep. gr. 72 ; Assembly overview - seat height adjustment
  • ⇒ Rep. gr. 72 ; Removing and installing seat height adjuster
  1. Driver seat adjustment operating unit - E470- / front passenger seat adjustment operating unit - E471-
  • Depending on equipment/version
  • ⇒ Rep. gr. 72 ; Removing and installing seat adjustment operating unit [E470]/[E471]
Volkswagen ID.4. Overview of fitting locations - electrical and electronic components
  1. Driver operating unit for memory settings - E464- / front passenger operating unit for memory settings - E465-
  • Depending on equipment/version
  • ⇒ "3.30 Removing and installing operating unit for memory settings [E464]/[E465]"
  1. Massage seat control unit
  • With control unit for front left massage seat - J803- or control unit for front right massage seat - J804-
  • Depending on equipment/version
  • Cannot be renewed individually
  • ⇒ Rep. gr. 72 ; Removing and installing lumbar support
  1. Left footwell light - W9- / right footwell light - W10-
  • ⇒ Electrical system; Rep. gr. 96 ; Lights; Removing and installing footwell light W9/W10
  1. Seat occupied sensor on driver side - G1067- / seat occupied sensor on front passenger side - G128-
  • ⇒ Rep. gr. 69 ; Removing and installing front seat occupied sensor [G1067]/[G128]
  1. Driver seat lumbar support adjustment switch - E176- / front passenger seat lumbar support adjustment switch - E177-
  • Depending on equipment/version
  • ⇒ Rep. gr. 72 ; Removing and installing lumbar support adjustment switch [E176]/[E177]
  1. Driver seat rake adjustment motor - V243- / front passenger seat rake adjustment motor - V244-
  • Depending on equipment/version
  • ⇒ Rep. gr. 72 ; Removing and installing seat rake adjustment motor [V243]/[V244]
  1. Electrical wire
  2. Seat and steering column adjustment control unit with memory - J136- / front passenger seat adjustment control unit with memory - J521-
  • Depending on equipment/version
  • ⇒ Rep. gr. 72 ; Removing and installing seat adjustment control unit
  1. Driver seat longitudinal adjustment motor - V28- / front passenger seat longitudinal adjustment motor - V31-
  • Depending on equipment/version
  • Cannot be renewed individually
  • ⇒ Rep. gr. 72 ; Removing and installing seat longitudinal adjustment motor [V28]/[V31]
  1. Front left seat heating - ZX11- / front right seat heating - ZX13-
  • Depending on equipment/version
  • ⇒ Rep. gr. 74 ; Removing and installing seat heating element [ZX11]/[ZX13]
  1. Driver side belt switch - E24- / front passenger side belt switch - E25-
  • ⇒ Rep. gr. 69 ; Assembly overview - front belt buckle
  • ⇒ Rep. gr. 69 ; Removing and installing front belt buckle
  1. Driver seat backrest adjustment motor - V45- / front passenger seat backrest adjustment motor - V46-
  • Depending on equipment/version
  • Cannot be renewed individually
  • ⇒ Rep. gr. 72 ; Removing and installing front backrest

Overview of fitting locations - electrical and electronic components, NAR

Overview is shown for right side of vehicle as an example

  1. Front side airbag, outer side
  • With side airbag igniter on front passenger side - N200- .
  • ⇒ Rep. gr. 69 ; Assembly overview - front side airbag, outer side
  • ⇒ Rep. gr. 69 ; Removing and installing front side airbag, outer side
  1. Backrest heating element
  • With heated backrest for front right seat - Z117- or heated backrest for front left seat - Z116-
  • Depending on equipment/ version
  • ⇒ Rep. gr. 74 ; Removing and installing backrest heating element [Z116]/[Z117]
  1. Lumbar support
  • Depending on equipment/ version
  • Cannot be renewed individually
  • ⇒ Rep. gr. 72 ; Removing and installing lumbar support
  1. Front passenger seat backrest adjustment motor - V46-
  • Depending on equipment/version
  • Cannot be renewed individually
  • ⇒ Rep. gr. 72 ; Removing and installing front backrest
  1. Front passenger side belt switch - E25-
  • ⇒ Rep. gr. 69 ; Assembly overview - front belt buckle
  • ⇒ Rep. gr. 69 ; Removing and installing front belt buckle
  1. Front right seat heating - ZX13- / front left seat heating - ZX11-
  • Depending on equipment/version
  • ⇒ Rep. gr. 74 ; Removing and installing seat heating element [ZX11]/[ZX13]
  1. Front passenger seat longitudinal adjustment motor - V31-
  • Depending on equipment/version
  • Cannot be renewed individually
  • ⇒ Rep. gr. 72 ; Removing and installing driver seat longitudinal adjustment motor [V28]
  1. Seat and steering column adjustment control unit with memory - J136- / front passenger seat adjustment control unit with memory - J521-
  2. Depending on equipment/version
  • ⇒ Rep. gr. 72 ; Removing and installing seat adjustment control unit
  1. Front passenger side seat position sensor - G554-
  • ⇒ Rep. gr. 72 ; Assembly overview - seat pan
Volkswagen ID.4. Overview of fitting locations - electrical and electronic components, NAR
  1. Electrical wire
  2. Front passenger seat rake adjustment motor - V244-
  • Depending on equipment/version
  • ⇒ Rep. gr. 72 ; Removing and installing seat rake adjustment unit
  1. Front passenger seat lumbar support adjustment switch - E177-
  • Depending on equipment/version
  • ⇒ Rep. gr. 72 ; Removing and installing lumbar support adjustment switch [E176]/[E177]
  1. Driver seat adjustment operating unit - E470- / front passenger seat adjustment operating unit - E471-
  • Depending on equipment/version
  • ⇒ Rep. gr. 72 ; Removing and installing seat adjustment operating unit [E470]/[E471]
  1. Front passenger seat height adjustment motor - V246-
  • Depending on equipment/version
  • ⇒ Rep. gr. 72 ; Assembly overview - seat height adjustment
  • ⇒ Rep. gr. 72 ; Removing and installing seat height adjuster
  1. Compressor for multicontour passenger seat - V440-
  • Cannot be renewed individually
  • Depending on equipment/version
  • ⇒ Rep. gr. 72 ; Removing and installing lumbar support
  1. Front passenger operating unit for memory settings - E465-
  • Depending on equipment/version
  • ⇒ Rep. gr. 72 ; Removing and installing operating unit for memory settings [E464]/[E465]
  1. Control unit for front right massage seat - J804- / control unit for front left massage seat - J803-
  • Cannot be renewed individually
  • Depending on equipment/version
  • ⇒ Rep. gr. 72 ; Removing and installing lumbar support
  1. Left footwell light - W9- / right footwell light - W10-
  • ⇒ Electrical system; Rep. gr. 96 ; Lights; Removing and installing footwell light W9/W10
  1. Seat occupied recognition control unit - J706-
  • ⇒ Rep. gr. 69 ; Removing and installing seat occupied recognition control unit [J706]

Assembly overview front seat

Assembly overview - front seat, manually adjustable

Overview shown for left side of vehicle as an example

  1. Front backrest
  • ⇒ Rep. gr. 72 ; Assembly overview - front backrest
  • ⇒ Rep. gr. 72 ; Removing and installing front backrest
  1. Head restraint
  • ⇒ Rep. gr. 72 ; Assembly overview - head restraint
  • ⇒ Rep. gr. 72 ; Removing and installing head restraint
  1. Backrest adjustment handle
  • ⇒ Rep. gr. 72 ; Removing and installing backrest adjustment handle
  1. Outer side trim
  • ⇒ Rep. gr. 72 ; Removing and installing outer seat trim
  1. Handle for seat height adjustment
  • ⇒ Rep. gr. 72 ; Removing and installing seat height adjustment handle
  1. Seat rail cover
  • Qty. 4
  1. Seat longitudinal adjustment handle
  • ⇒ Rep. gr. 72 ; Removing and installing seat longitudinal adjustment handle
  1. Seat pan
  • ⇒ Rep. gr. 72 ; Assembly overview - seat pan
  1. Front belt buckle
  • ⇒ Rep. gr. 69 ; Assembly overview - front belt buckle
  • ⇒ Rep. gr. 69 ; Removing and installing front belt buckle
  1. Inner seat trim
  • ⇒ Rep. gr. 72 ; Removing and installing inner seat trim
  1. Bolt
  • Qty. 4
  • 40 N·m
  1. Centre armrest
  • ⇒ Rep. gr. 68 ; Assembly overview - front centre armrest
  • ⇒ Rep. gr. 68 ; Removing and installing front centre armrest
Volkswagen ID.4. Assembly overview - front seat, manually adjustable

Assembly overview - front seat, electric adjustment

Overview shown for left side of vehicle as an example

  1. Front backrest
  • ⇒ Rep. gr. 72 ; Assembly overview - front backrest
  • ⇒ Rep. gr. 72 ; Removing and installing front backrest
  1. Head restraint
  • ⇒ Rep. gr. 72 ; Assembly overview - head restraint
  • ⇒ Rep. gr. 72 ; Removing and installing head restraint
  1. Outer seat trim
  • ⇒ "3.26.1 Removing and installing outer seat trim"
  1. Driver operating unit for memory settings - E464- / front passenger operating unit for memory settings - E465-
  • ⇒ Rep. gr. 72 ; Removing and installing operating unit for memory settings [E464]/[E465]
  1. Driver seat adjustment operating unit - E470- / front passenger seat adjustment operating unit - E471-
  • ⇒ Rep. gr. 72 ; Removing and installing seat adjustment operating unit [E470]/[E471]
  1. Seat rail cover
  • Qty. 4
  1. Driver seat lumbar support adjustment switch - E176- / front passenger seat lumbar support adjustment switch - E177-
  • ⇒ Rep. gr. 72 ; Removing and installing lumbar support adjustment switch [E176]/[E177]
  1. Seat depth adjustment
  • ⇒ Rep. gr. 72 ; Assembly overview - seat depth adjustment
  • ⇒ Rep. gr. 72 ; Removing and installing seat depth adjuster
  1. Seat pan
  • ⇒ Rep. gr. 72 ; Assembly overview - seat pan
  1. Front belt buckle
  • ⇒ Rep. gr. 69 ; Assembly overview - front belt buckle
  • ⇒ Rep. gr. 69 ; Removing and installing front belt buckle
  1. Inner seat trim
  • ⇒ "3.25 Removing and installing inner seat trim"
  1. Bolt
  • Qty. 4
  • 40 N·m
Volkswagen ID.4. Assembly overview - front seat, electric adjustment
  1. Centre armrest
  • ⇒ Rep. gr. 68 ; Assembly overview - front centre armrest
  • ⇒ Rep. gr. 68 ; Removing and installing front centre armrest

Assembly overview - front seat, Top-Sport

Overview shown for left side of vehicle as an example

Volkswagen ID.4. Assembly overview - front seat, Top-Sport
  1. Front centre armrest
  • ⇒ Rep. gr. 68 ; Assembly overview - front centre armrest
  • ⇒ Rep. gr. 68 ; Removing and installing front centre armrest
  1. Front backrest
  • ⇒ Rep. gr. 72 ; Assembly overview - front backrest
  • ⇒ Rep. gr. 72 ; Removing and installing front backrest
  1. Bolt
  • Qty. 4
  • 40 N·m
  1. Bolt
  • Qty. 3
  • Renew after removing
  • 6,5 N·m
  1. Driver seat height adjustment motor - V245- / front passenger seat height adjustment motor - V246-
  • ⇒ Rep. gr. 72 ; Removing and installing seat height adjustment unit, electrically adjustable
  1. Outer seat trim
  • ⇒ Rep. gr. 72 ; Removing and installing outer seat trim
  1. Seat rail cover
  • Qty. 2 or 4 depending on model
  1. Driver operating unit for memory settings - E464- / front passenger operating unit for memory settings - E465-
  • ⇒ Rep. gr. 72 ; Removing and installing operating unit for memory settings [E464]/[E465]
  1. Driver seat adjustment operating unit - E470- / front passenger seat adjustment operating unit - E471-
  • ⇒ Rep. gr. 72 ; Removing and installing seat adjustment operating unit [E470]/[E471]
  1. Driver seat lumbar support adjustment switch - E176- / front passenger seat lumbar support adjustment switch - E177-
  • ⇒ Rep. gr. 72 ; Removing and installing lumbar support adjustment switch [E176]/[E177]
  1. Driver seat longitudinal adjustment motor - V28-
  • ⇒ Rep. gr. 72 ; Removing and installing seat longitudinal adjustment motor [V28]
  1. Seat depth adjustment handle
  • ⇒ Rep. gr. 72 ; Assembly overview - seat depth adjustment
  • ⇒ Rep. gr. 72 ; Removing and installing seat depth adjuster
  1. Seat depth adjuster trim
  • ⇒ Rep. gr. 72 ; Assembly overview - seat depth adjustment
  • ⇒ Rep. gr. 72 ; Removing and installing seat depth adjuster
  1. Seat pan
  • ⇒ Rep. gr. 72 ; Assembly overview - seat pan
  1. Front belt buckle
  • ⇒ Rep. gr. 69 ; Assembly overview - front belt buckle
  • ⇒ Rep. gr. 69 ; Removing and installing front belt buckle

Assembly overview - front backrest

Assembly overview - front backrest

Overview shown for left side of vehicle as an example

Volkswagen ID.4. Assembly overview - front backrest
  1. Head restraint
  • Depending on equipment/ version
  • ⇒ Rep. gr. 72 ; Assembly overview - head restraint
  • ⇒ Rep. gr. 72 ; Removing and installing head restraint
  1. Head restraint guide
  • Depending on equipment/ version
  • ⇒ Rep. gr. 72 ; Assembly overview - head restraint
  • ⇒ Rep. gr. 72 ; Removing and installing head restraint guide
  1. Front backrest
  • ⇒ Rep. gr. 72 ; Removing and installing front backrest
  1. Backrest adjustment handle
  • For vehicles without electric backrest adjustment
  • ⇒ Rep. gr. 72 ; Removing and installing backrest adjustment handle
  1. Bolt
  • Qty. 4
  • Renew after removing
  1. Centre armrest
  • ⇒ Rep. gr. 68 ; Assembly overview - front centre armrest
  • ⇒ Rep. gr. 68 ; Removing and installing front centre armrest

Specified torque and tightening sequence

Volkswagen ID.4. Assembly overview - front backrest

Assembly overview - front backrest, Top-Sport

Overview shown for left side of vehicle as an example

Volkswagen ID.4. Assembly overview - front backrest, Top-Sport
  1. Backrest padding
  • ⇒ Rep. gr. 74 ; Removing and installing backrest cover and padding
  • ⇒ Rep. gr. 74 ; Separating backrest cover from backrest padding
  1. Head restraint
  • ⇒ Rep. gr. 72 ; Removing and installing integrated head restraint
  1. Bolt
  • Qty. 4
  • 1 N·m
  1. Rear trim panel
  • ⇒ "3.11 Removing and installing trim for backrest with integrated head restraint", page 208
  1. Retainer
  • Qty. 2
  • ⇒ "3.11 Removing and installing trim for backrest with integrated head restraint", page 208
  1. Head restraint guide
  • ⇒ Rep. gr. 72 ; Removing and installing head restraint guide
  1. Front backrest
  • ⇒ Rep. gr. 72 ; Removing and installing front backrest
  1. Bolt
  • Qty. 2
  • 2 N·m
  1. Backrest frame
  2. Bolt
  • Qty. 4
  • Renew after removing
  1. Front trim panel
  • ⇒ "3.11 Removing and installing trim for backrest with integrated head restraint"

Specified torque and tightening sequence

Volkswagen ID.4. Assembly overview - front backrest, Top-Sport

Assembly overview - head restraint

Overview shows left-side of vehicle as an example

Volkswagen ID.4. Assembly overview - head restraint
  1. Head restraint
  • ⇒ Rep. gr. 72 ; Removing and installing head restraint
  1. Cover
  • Qty. 2
  1. Head restraint guide
  • ⇒ Rep. gr. 72 ; Removing and installing head restraint guide
  1. Head restraint release button
  2. Backrest frame
  3. Bolt
  • Qty. 2
  • 2 N·m

Assembly overview seat pan

Assembly overview - seat pan, manual adjustment

Overview shows left-side of vehicle as an example

  1. Padding
  • ⇒ Rep. gr. 74 ; Assembly overview - seat pan cover and padding
  • ⇒ Rep. gr. 74 ; Removing and installing seat pan cover and padding
  • ⇒ Rep. gr. 74 ; Separating seat pan cover from seat pan padding
  1. Seat pan
  2. Seat trim bracket
  • ⇒ Rep. gr. 72 ; Removing and installing bracket for seat trim
  1. Outer seat trim
  • ⇒ Rep. gr. 72 ; Removing and installing outer seat trim
  1. Backrest adjustment handle
  • ⇒ Rep. gr. 72 ; Removing and installing backrest adjustment handle
  1. Spreader rivet
  • Left and right
  1. Lever for seat height adjustment
  • ⇒ Rep. gr. 72 ; Removing and installing seat height adjustment unit, manually adjustable
  1. Retaining clip
  2. Handle for seat height adjustment
  • Renew after removing
  • ⇒ Rep. gr. 72 ; Removing and installing seat height adjustment handle
  1. Bolt
  • Qty. 2
  • 8 N·m
  1. Bolt
  • ⇒ Rep. gr. 69 ; Assembly overview - front belt buckle
  1. Front belt buckle
  • ⇒ Rep. gr. 69 ; Assembly overview - front belt buckle
  • ⇒ Rep. gr. 69 ; Removing and installing front belt buckle
  1. Inner seat trim
  • ⇒ Rep. gr. 72 ; Removing and installing inner seat trim
Volkswagen ID.4. Assembly overview - seat pan, manual adjustment

Assembly overview - seat pan, electric adjustment

Overview shown for left side of vehicle as an example

  1. Padding
  • ⇒ Rep. gr. 74 ; Assembly overview - seat pan cover and padding
  • ⇒ Rep. gr. 74 ; Removing and installing seat pan cover and padding
  • ⇒ Rep. gr. 74 ; Separating seat pan cover from seat pan padding
  1. Bolt
  • Qty. 4
  • 22 N·m
  1. Seat pan
  2. Seat trim bracket
  • ⇒ Rep. gr. 72 ; Removing and installing seat trim bracket
  1. Driver operating unit for memory settings - E464- / front passenger operating unit for memory settings - E465-
  • Driver operating unit for memory settings - E464- with seat memory position button 1 - E218- , seat memory position button 2 - E219- , seat memory position button 3 - E220- , driver seat memory function button - E283- , driver seat massage function button - E670-
  • Front passenger operating unit for memory settings - E465- with seat memory position button 1 - E218- , seat memory position button 2 - E219- , seat memory position button 3 - E220- , front passenger seat memory function button - E340- , front passenger seat massage function button - E671-
  • ⇒ Rep. gr. 72 ; Removing and installing operating unit for memory settings [E464]/[E465]
  1. Outer seat trim
  • ⇒ Rep. gr. 72 ; Removing and installing outer seat trim
  1. Spreader rivet
  • Qty. 2
  1. Driver seat adjustment operating unit - E470- / front passenger seat adjustment operating unit - E471-
  • ⇒ Rep. gr. 72 ; Removing and installing seat adjustment operating unit [E470]/[E471]
  1. Driver seat lumbar support adjustment switch - E176- / front passenger seat lumbar support adjustment switch - E177-
  • ⇒ Rep. gr. 72 ; Removing and installing lumbar support adjustment switch [E176]/[E177]
  1. Bolt
  • Qty. 5
  • 1 N·m
  1. Bolt
  • Qty. 2
Volkswagen ID.4. Assembly overview - seat pan, electric adjustment
  • 8 N·m
  1. Lower frame of seat pan
  • With driver seat longitudinal adjustment motor - V28- or front passenger seat longitudinal adjustment motor - V31-
  • ⇒ Rep. gr. 72 ; Removing and installing seat longitudinal adjustment motor [V28]/[V31]
  1. Bolt
  • Specified torque ⇒ Rep. gr. 69 ; Assembly overview - front belt buckle
  1. Front belt buckle
  • ⇒ Rep. gr. 69 ; Assembly overview - front belt buckle
  • ⇒ Rep. gr. 69 ; Removing and installing front belt buckle
  1. Inner seat trim
  • ⇒ Rep. gr. 72 ; Removing and installing inner seat trim

Assembly overview seat pan, fixed seat

The overview shows a left-hand drive vehicle as an example.

  1. Padding
  • ⇒ Rep. gr. 74 ; Assembly overview - seat pan cover and padding
  • ⇒ Rep. gr. 74 ; Removing and installing seat pan cover and padding
  • ⇒ Rep. gr. 74 ; Separating seat pan cover from seat pan padding
  1. Spreader rivet
  • Qty. 2
  1. Inner seat trim
  • ⇒ "3.25 Removing and installing inner seat trim"
  1. Belt buckle
  • ⇒ Rep. gr. 69 ; Assembly overview - front belt buckle
  • ⇒ Rep. gr. 69 ; Removing and installing front belt buckle
  1. Bolt
  • Specified torque ⇒ Rep. gr. 69 ; Assembly overview - front belt buckle
  1. Seat pan
  2. Outer seat trim
  • ⇒ "3.26.2 Removing and installing outer seat trim, front passenger seat without height adjustment"
  1. Backrest adjustment handle
  • ⇒ Rep. gr. 72 ; Removing and installing backrest adjustment handle
Volkswagen ID.4. Assembly overview   seat pan, fixed seat

Assembly overview - seat pan, NAR

Overview shown for left side of vehicle as an example

  1. Padding
  • ⇒ Rep. gr. 74 ; Assembly overview - seat pan cover and padding
  • ⇒ Rep. gr. 74 ; Removing and installing seat pan cover and padding
  • ⇒ Rep. gr. 74 ; Separating seat pan cover from seat pan padding
  1. Bolt
  • Qty. 4
  • 22 N·m
  1. Seat pan
  2. Seat trim bracket
  • ⇒ Rep. gr. 72 ; Removing and installing seat trim bracket
  1. Driver operating unit for memory settings - E464- / driver operating unit for memory settings - E464-
  • Driver operating unit for memory settings - E464- with seat memory position button 1 - E218- , seat memory position button 2 - E219- , seat memory position button 3 - E220- , driver seat memory function button - E283- , driver seat massage function button - E670-
  • Driver operating unit for memory settings - E464- with seat memory position button 1 - E218- , seat memory position button 2 - E219- , seat memory position button 3 - E220- , front passenger seat memory function button - E340- , front passenger seat massage function button - E671-
  • ⇒ Rep. gr. 72 ; Removing and installing operating unit for memory settings [E464]/[E465]
  1. Outer seat trim
  • ⇒ "3.26.1 Removing and installing outer seat trim"
  1. Spreader rivet
  • Qty. 2
  1. Driver seat adjustment operating unit - E470- / front passenger seat adjustment operating unit - E471-
  • ⇒ Rep. gr. 72 ; Removing and installing seat adjustment operating unit [E470]/[E471]
  1. Driver seat lumbar support adjustment switch - E176- / front passenger seat lumbar support adjustment switch - E177-
  • ⇒ Rep. gr. 72 ; Removing and installing lumbar support adjustment switch [E176]/[E177]
  1. Bolt
  • Qty. 5
  • 1 N·m
  1. Bolt
  • Qty. 2
Volkswagen ID.4. Assembly overview - seat pan, NAR
  • 8 N·m
  1. Bolt
  • 1,2 N·m
  1. Driver side seat position sensor - G553- / front passenger side seat position sensor - G554-
  • Cannot be renewed individually
  1. Lower frame of seat pan
  • With driver seat longitudinal adjustment motor - V28- or front passenger seat longitudinal adjustment motor - V31-
  • ⇒ Rep. gr. 72 ; Removing and installing seat longitudinal adjustment motor [V28]/[V31]
  1. Spreader rivet
  2. Bolt
  • Specified torque ⇒ Rep. gr. 69 ; Assembly overview - front belt buckle
  1. Inner seat trim
  • ⇒ "3.25 Removing and installing inner seat trim"
  1. Front belt buckle
  • ⇒ Rep. gr. 69 ; Assembly overview - front belt buckle
  • ⇒ Rep. gr. 69 ; Removing and installing front belt buckle

Assembly overview seat height adjustment

Assembly overview - seat height adjustment, manual

Overview shown for left side of vehicle as an example

Volkswagen ID.4. Assembly overview  seat height adjustment
  1. Handle for seat height adjustment
  • ⇒ Rep. gr. 72 ; Removing and installing seat height adjustment handle
  1. Retaining clip
  2. Operating lever for seat height adjustment
  3. Bolt
  • Qty. 3
  • 10 N·m
  1. Adjuster
  2. Bolt
  • Qty. 2
  • 8 N·m

Assembly overview seat height adjustment, electrical

The overview is shown for the left side of vehicle as an example.

  1. Bolt
  • Qty. 3
  • Renew after removing
  • 6,5 N·m
  1. Driver seat height adjustment motor - V245- / front passenger seat height adjustment motor - V246-
  • ⇒ "3.14.2 Removing and installing seat height adjustment unit, electrically adjustable"
  1. Seat pan

Assembly overview lumbar support

The overview is shown for the left side of vehicle as an example.

  1. Bolt
  • 1 N·m
  1. Compressor for multicontour driver seat - V439- / compressor for multicontour front passenger seat - V440-
  • Cannot be renewed individually
  • ⇒ Rep. gr. 72 ; Removing and installing lumbar support
  1. Backrest frame
  2. Bolt
  • 8 N·m
  1. Wire
  2. Wire
  3. Lumbar support
  • ⇒ Rep. gr. 72 ; Removing and installing lumbar support
Volkswagen ID.4. Assembly overview  lumbar support

Assembly overview seat rake adjustment

The overview is shown for the left side of vehicle as an example.

  1. Driver seat rake adjustment motor - V243- / front passenger seat rake adjustment motor - V244-
  • ⇒ Rep. gr. 72 ; Removing and installing seat rake adjustment motor [V243]/[V244]
  1. Bracket
  2. Bolt
  • Qty. 2
  • Renew after removing
  • 10 N·m
  1. Adjustment spindle
  2. Bolt
  • Renew after removing
  • 20 N·m
Volkswagen ID.4. Assembly overview  seat rake adjustment

Assembly overview seat depth adjustment

  1. Seat depth adjuster mounting plate
  • ⇒ Rep. gr. 72 ; Removing and installing seat depth adjuster
  1. Bolt
  • Qty. 4
  • 6 N·m
  1. Seat depth adjuster trim
  • ⇒ Rep. gr. 72 ; Removing and installing seat depth adjuster
  1. Seat depth adjustment handle
  • ⇒ Rep. gr. 72 ; Removing and installing seat depth adjuster
  1. Nut
  • Qty. 4
  • Renew after removing
  • 6 N·m
Volkswagen ID.4. Assembly overview  seat depth adjustment

Removing and installing front seat

Removal and installation are described for the left side of vehicle as an example.

Removing

  • Move front seat to foremost and highest position.
  • Unscrew bolts -1-.
  • Move front seat to rearmost and lowest position.
  • Unscrew bolts -2-.
  • Fold front seat backwards.
Volkswagen ID.4. Removing and installing front seat
  • Switch off ignition and electrical equipment.
  • Keep vehicle key and other entry and start authorisation devices (e.g. smartphone) outside vehicle.
  • Disconnect battery ⇒ Electrical system; Rep. gr. 27 ; Battery; Disconnecting and connecting battery
  • Open cover in floor covering.

CAUTION

It is possible to trigger pyrotechnic components unintentionally.

Risk of injury

  • Discharge static electricity by briefly touching door striker plate.
  • Disconnect electrical connectors.

NOTICE

Risk of damage to the front seat at lifting out or during transportation.

  • Do not grab the front seat by attachments when lifting (e.g.

    belt buckle, seat longitudinal adjustment lever, seat height adjustment lever or seat trim).

  • Use suitable means to protect attachments against damage.

Important

  • The aid of an additional person is required for the subsequent work steps.
  • Lift out front seat.

Installing

Install in reverse order of removal, observing the following:

  • Insert front seat.
  • First insert centring pin on front inner side -arrow-, and then insert centring pin on rear inner side -arrow-.
Volkswagen ID.4. Removing and installing front seat

Aign seat rails.

Important

  • Seat rails must have the same position in fastener.
  • Align front seat.
  • Connect electrical connector.
  • Connect battery earth cable ⇒ Electrical system; Rep.

    gr. 27 ; Battery; Disconnecting and connecting battery .

  • Switch on ignition.
  • Read and clear event memory using ⇒ Vehicle diagnostic tester.

NOTICE

Risk of damage to threads in the seat cross member mounting plate.

  • Proceed with caution when screwing the bolts in.
  • Screw in bolts -2- by hand.
  • Move front seat to foremost and highest position.
  • Screw in bolts -1- hand-tight.
  • Tighten bolts -1-.
  • Move front seat to rearmost and lowest position.
  • Tighten bolts -2-.
Volkswagen ID.4. Removing and installing front seat

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - front seat

Removing and installing trim for backrest with integrated head restraint

Trim for backrest with integrated head restraint is referred to hereafter as trim.

Removing

  • Use a commercially available plastic wedge to unclip rear trim -1-.
Volkswagen ID.4. Removing and installing trim for backrest with integrated head restraint
  • Unscrew bolts -2-.
  • Remove retainers -1-.
Volkswagen ID.4. Removing and installing trim for backrest with integrated head restraint
  • Unclip front trim -1-.
Volkswagen ID.4. Removing and installing trim for backrest with integrated head restraint

Installing

Install in reverse order of removal, observing the following:

  • Push on trim until it can be heard to engage.

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - front backrest, Top- Sport

Removing and installing seat longitudinal adjustment handle

Removal and installation are described for left side of vehicle as an example.

Removing

  • Disconnect seat longitudinal adjustment handle -1- from handle mounting using commercially available rubber-headed hammer.
Volkswagen ID.4. Removing and installing seat longitudinal adjustment handle

Installing

NOTICE

Risk of damage to seat longitudinal adjustment handle from excessive force.

  • Drive off seat longitudinal adjustment handle carefully.
  • Drive on seat longitudinal adjustment handle as far as stop using commercially available rubber-headed hammer.

Removing and installing seat height adjustment handle

Seat height adjustment handle is referred to hereafter as handle.

Removal and installation are described for the left-side of vehicle as an example.

Removing

  • Pull handle -1- as far as possible upwards, and hold it there.
  • Guide a commercially available screwdriver through handle -1- and outer seat trim -2- up to retaining clip -3-.
  • Release retaining clip -3- using the commercially available screwdriver.
  • Pull handle -1- in direction of -arrow- off seat height adjustment lever -4-.
Volkswagen ID.4. Removing and installing seat height adjustment handle

Installing

Install in reverse order of removal, observing the following:

Removing and installing seat height adjuster

Removing and installing seat height adjustment unit, manually adjustable

Removal and installation are described for the left-side of vehicle as an example.

Removing

  • Remove outer seat trim ⇒ Rep. gr. 72 ; Removing and installing outer seat trim
  • Unscrew bolts -2-.
  • Remove lever for seat height adjustment -1-.
Volkswagen ID.4. Removing and installing seat height adjustment unit, manually adjustable
  • Take out the lock washer -2-.
  • Unscrew bolts -1-.
  • Remove seat height adjustment unit.
Volkswagen ID.4. Removing and installing seat height adjustment unit, manually adjustable

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - front seat, manual adjustment

Removing and installing seat height adjustment unit, electrically adjustable

Driver seat height adjustment motor - V245- and front passenger seat height adjustment motor - V246- are referred to hereafter as height adjustment motor.

Removal and installation are described for the left-side of vehicle as an example.

Removing

  • Remove seat pan cover and padding ⇒ Rep. gr. 74 ; Removing and installing seat pan cover and padding .
  • Take out the lock washer -2-.
  • Unscrew bolts -1-.
Volkswagen ID.4. Removing and installing seat rake adjustment motor [V243]/[V244]
  • Disconnect electrical connector -2-.
  • Remove seat height adjustment motor -1-.
Volkswagen ID.4. Removing and installing seat rake adjustment motor [V243]/[V244]

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - front seat, electric adjustment

Removing and installing seat rake adjustment motor [V243]/[V244]

The driver seat rake adjustment motor - V243- and front passenger seat rake adjustment motor - V244- will henceforth be referred to as "rake adjustment motor".

Removal and installation are described for the left side of vehicle as an example

Removing

  • ⇒ Rep. gr. 72 ; Secure front seat to seat repair stand .
  • Disconnect connector -5-.
  • Unscrew bolt -3-.
  • Unscrew bolts -2-.
  • Remove seat rake adjustment motor -4-.
Volkswagen ID.4. Removing and installing seat rake adjustment motor [V243]/[V244]

Installing

Install in reverse order of removal, observing the following:

Tightening torques

⇒ "3.8 Assembly overview seat rake adjustment"

Removing and installing head restraint

Removing

  • Remove front seat ⇒ Rep. gr. 72 ; Removing and installing front seat .
  • Remove inner seat trim ⇒ Rep. gr. 72 ; Removing and installing inner seat trim .
  • Remove outer seat trim ⇒ Rep. gr. 72 ; Removing and installing outer seat trim .
  • Disconnect electrical connector -3-.
  • Unclip retaining clips -2- of electrical wire -1- on seat pan.
  • Guide out electrical wire -1- leading to side airbag on front outer side from braided sleeving.
Volkswagen ID.4. Removing and installing head restraint

Driver seat

  • Guide out electrical wire leading to side airbag on front inner side from braided sleeving.

All vehicles (continued)

  • Remove bolts -1-, -2-, -3- and-4-.
  • Tilt front backrest -5- forwards.
Volkswagen ID.4. Removing and installing head restraint
  • Push seat pan padding to one side.
  • Pull out electrical wire for side airbag on front outer side from seat pan.

Driver seat

  • Pull out electrical wire for side airbag on front inner side from seat pan.

All vehicles (continued)

  • Remove front backrest.

Installing

Install in reverse order of removal, observing the following:

  • Route electrical wire so that original wiring layout is restored.

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - front backrest

Removing and installing head restraint

Removal and installation are described for left side of vehicle as an example.

Removing

  • Move front seat to foremost and lowest position.
  • Tilt front backrest 45º forwards.
  • Press head restraint release button -2- and pull head restraint -1- in direction of -arrow- as far as stop.
Volkswagen ID.4. Removing and installing head restraint
  • Press down padding in area of head restraint guides.
  • Press button -arrow- on head restraint guide -2- down as far as stop.
  • Pull out head restraint -1-.
Volkswagen ID.4. Removing and installing head restraint

Installing

Install in reverse order of removal, observing the following:

  • Push head restraint as far as possible downwards.

Removing and installing integrated head restraint

Removing

  • Separate backrest cover from backrest padding ⇒ Rep.

    gr. 74 ; Separating backrest cover from backrest padding .

  • Press head restraint release button -arrow- and pull out integrated head restraint -1-.
Volkswagen ID.4. Removing and installing integrated head restraint

Installing

Install in reverse order of removal, observing the following:

  • Push integrated head restraint downwards until it can be heard to engage.

Removing and installing head restraint guide

Removing

  • Remove backrest cover and padding ⇒ Rep. gr. 74 ; Removing and installing backrest cover and padding .
  • Release head restraint guides -1- in direction of -arrow A-.
  • Pull out head restraint guides -1- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing head restraint guide

Installing

Install in reverse order.

Removing and installing head restraint guide, integrated head restraint

Removing

  • Remove backrest cover and padding ⇒ Rep. gr. 74 ; Removing and installing backrest cover and padding .
  • Remove integrated head restraint ⇒ Rep. gr. 72 ; Removing and installing integrated head restraint .
  • Unscrew bolts -2-.
Volkswagen ID.4. Removing and installing head restraint guide, integrated head restraint
  • Release locking devices -2-.
  • Push head restraint guide -1- in direction of -arrow A-, and pull it out in direction of -arrow B-.
Volkswagen ID.4. Removing and installing head restraint guide, integrated head restraint

Installing

Install in reverse order of removal, observing the following:

Important

  • Two lower locking devices must engage fully with backrest frame.

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - head restraint

Removing and installing lumbar support adjustment switch [E176]/[E177]

Removing

The driver seat lumbar support adjustment switch - E176- and front passenger seat lumbar support adjustment switch - E177- will hence forth be referred to as "lumbar support adjustment switch".

Removal and installation are described for the left side of vehicle as an example.

  • Remove outer seat trim ⇒ "3.26.1 Removing and installing outer seat trim"
  • Unscrew bolts -1-.
  • Disconnect electrical connector.
  • Remove lumbar support adjustment switch -2-.
Volkswagen ID.4. Removing and installing lumbar support adjustment switch [E176]/[E177]

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - seat pan

Removing and installing backrest adjuster

Special tools and workshop equipment required

  • assembly tool - 3399-

Removal and installation are described for the left-side of vehicle as an example.

Removing

  • Turn backrest adjuster -1- until detent -arrow A- is visible.
  • Insert assembly tool - 3399- -2- and lever backrest adjuster -1- in direction of -arrow B-.
  • Turn backrest adjuster -1- 120º further.
  • Insert assembly tool - 3399- -2- and lever backrest adjuster -1- in direction of -arrow B-.
  • Detach backrest adjuster -1-.
Volkswagen ID.4. Removing and installing backrest adjuster

Installing

Install in reverse order of removal, observing the following:

  • Check whether backrest adjuster is firmly attached by pulling on it.

Securing front seat to seat repair stand

Special tools and workshop equipment required

  • bracket for seat repairs - VAS 6136-
  • engine and gearbox bracket - VAS 6095A-
  • seat repair adapter - VAS 6136/1-
  • Remove front seat ⇒ Rep. gr. 72 ; Removing and installing front seat .
  • Attach bracket for seat repairs - VAS 6136- -B- to engine and gearbox bracket - VAS 6095A- -A-.
  • Secure front seat -1- with seat repair adapter - VAS 6136/1- -C- to bracket for seat repairs - VAS 6136- -B-.
Volkswagen ID.4. Securing front seat to seat repair stand

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - front seat

Removing and installing lumbar support

The compressor for multicontour driver seat - V439- or compressor for multicontour front passenger seat - V440- will henceforth be referred to as "compressor for multicontour seat".

Removal and installation are described for the left side of vehicle as an example.

Removing

  • Remove backrest cover and padding ⇒ Rep. gr. 74 ; Removing and installing backrest cover and padding .
  • Unscrew bolt -3-.
  • Disconnect electrical connector from compressor for multicontour seat -1-.
  • Detach compressor for multicontour seat -1- from backrest frame -2-.
Volkswagen ID.4. Removing and installing lumbar support
  • Unscrew bolt -4-.
  • Guide out wires -2- and -3-.
  • Remove lumbar support -1- along with compressor for multicontour seat.
Volkswagen ID.4. Removing and installing lumbar support

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ "3.7 Assembly overview lumbar support"

Removing and installing seat adjustment operating unit [E470]/[E471]

Special tools and workshop equipment required

  • release tool - T10236-

Removing

Driver seat adjustment operating unit - E470- and front passenger seat adjustment operating unit - E471- are referred to hereafter as seat adjustment operating unit.

Removal and installation are described for left side of vehicle as an example.

  • Remove outer seat trim ⇒ "3.26.1 Removing and installing outer seat trim"
  • Lever off buttons -3- and -4- using release tool - T10236- .
  • Unscrew bolts -2-.
  • Remove seat adjustment operating unit -1-.
Volkswagen ID.4. Removing and installing seat adjustment operating unit [E470]/[E471]

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - seat pan

Removing and installing bracket for seat trim

Removal and installation are described for the left-side of vehicle as an example.

Removing

  • Remove outer seat trim ⇒ Rep. gr. 72 ; Removing and installing outer seat trim .
  • Unscrew bolts -2-.
  • Detach seat trim bracket -1- in direction of -arrow-, and remove it from front seat -3-.
Volkswagen ID.4. Removing and installing bracket for seat trim

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - seat pan

Removing and installing inner seat trim

Removal and installation are described for the left side of vehicle as an example.

Removing

  • Remove front seat ⇒ Rep. gr. 72 ; Removing and installing front seat .
  • Press clamping pin in spreader rivet -1- inwards.
  • Lever off spreader rivet -1- using commercially available plastic wedge.
  • Release fastener -arrow-.
  • Remove inner seat trim -2- towards rear.
Volkswagen ID.4. Removing and installing inner seat trim

Installing

Install in reverse sequence of removal.

Removing and installing outer seat trim

Removal and installation are described for the left side of vehicle as an example.

Removing

  • Move front seat to foremost and highest position.

Manually adjustable front seat

  • Remove backrest adjustment handle ⇒ Rep. gr. 72 ; Removing and installing backrest adjustment handle .
  • Remove height adjustment handle ⇒ Rep. gr. 72 ; Removing and installing height adjustment handle .

All vehicles (continued)

  • Press clamping pin in spreader rivet -2- inwards.
  • Lever off spreader rivet -2- using commercially available plastic wedge.
  • Open locking element -4
Volkswagen ID.4. Removing and installing outer seat trim
  • Release fasteners -arrows-.
  • Detach outer seat trim -1- from seat trim bracket -2-.
Volkswagen ID.4. Removing and installing outer seat trim

Electrically adjustable front seat

  • Disconnect electrical connectors.

All vehicles (continued)

Installing

Install in reverse sequence of removal.

Removing and installing outer seat trim, front passenger seat without height adjustment

Removing

Removal and installation are described for a left-hand drive vehicle as an example.

  • Move front seat to foremost position.
  • Remove backrest adjustment handle ⇒ Rep. gr. 72 ; Removing and installing backrest adjustment handle .
  • Unscrew bolt -2-.
  • Press clamping pin in spreader rivet -3- inwards.
  • Lever off spreader rivet -3- using commercially available plastic wedge.
Volkswagen ID.4. Removing and installing outer seat trim, front passenger seat without height adjustment
  • Detach mounting points -2-.
  • Remove outer seat trim -1-.
Volkswagen ID.4. Removing and installing outer seat trim, front passenger seat without height adjustment

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - seat pan

Removing and installing seat longitudinal adjustment motor [V28]/[V31]

The driver seat longitudinal adjustment motor - V28- and front passenger seat longitudinal adjustment motor - V31- are removed together with the lower seat pan frame.

The driver seat longitudinal adjustment motor - V28- and front passenger seat longitudinal adjustment motor - V31- will henceforth be referred to as "seat longitudinal adjustment motor".

Removal and installation are described for the left side of vehicle as an example.

Removing

  • Remove front belt buckle ⇒ Rep. gr. 69 ; Removing and installing front belt buckle .
  • Disconnect electrical connector of seat longitudinal adjustment motor.
  • Unclip electrical wire from lower seat pan frame -3-, and lay it to one side.
  • Unscrew left-hand threaded bolt -2-.
  • Remove seat pan -1-.
Volkswagen ID.4. Removing and installing seat longitudinal adjustment motor [V28]/[V31]

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - seat pan

Removing and installing seat depth adjuster

Removal and installation are described for left side of vehicle as an example.

Removing

  • ⇒ Rep. gr. 72 ; Secure front seat to seat repair stand .
  • Remove seat adjustment control unit ⇒ Rep. gr. 72 ; Removing and installing seat adjustment control unit .
  • Move seat depth adjuster to foremost position.
  • Release fasteners -arrows- using commercially available plastic wedge.
  • Detach seat depth adjuster trim -2-.
  • Unclip seat depth adjuster handle -1-.
Volkswagen ID.4. Removing and installing seat depth adjuster
  • Detach seat pan cover -1- from front profile in direction of -arrow-.
Volkswagen ID.4. Removing and installing seat depth adjuster
  • Unscrew nuts -3-.
  • Release fasteners -4-.
Volkswagen ID.4. Removing and installing seat depth adjuster
  • Fold seat depth adjuster -1- upwards.
  • Disconnect electrical wire of seat heating element.
  • Release cover from side fasteners -2- in direction of -arrow-.
Volkswagen ID.4. Removing and installing seat depth adjuster
  • Detach fasteners -arrows- using commercially available plastic wedge.
  • Unclip padding -1- from seat depth adjuster -2-.
  • Remove seat depth adjustment unit -2-.
Volkswagen ID.4. Removing and installing seat depth adjuster

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - seat depth adjustment

Removing and installing seat adjustment control unit

Control unit for seat and steering column adjustment with memory function - J136- and control unit for front passenger seat adjustment with memory function - J521- will henceforth be referred to as "seat adjustment control unit".

Removing

  • ⇒ Rep. gr. 72 ; Secure front seat to seat repair stand .
  • Unclip electrical wire from retainer -2-.
  • Disconnect electrical connectors -3-.
  • Unclip seat adjustment control unit -1- at retaining tabs -arrows-.
  • Detach seat adjustment control unit -1- in direction of -arrow A-.
Volkswagen ID.4. Removing and installing seat adjustment control unit

Installing

Install in reverse order of removal, observing the following:

  • Route electrical wire so that original wiring layout is restored.

Removing and installing operating unit for memory settings [E464]/[E465]

The driver operating unit for memory settings - E464- and front passenger operating unit for memory settings - E465- will henceforth be referred to as "operating unit for memory settings".

Removal and installation are described for the driver side as an example.

Removing

  • Remove outer seat trim ⇒ Rep. gr. 72 ; Removing and installing outer seat trim .
  • Release locking devices -2-.
  • Remove operating unit for memory settings -1-.
Volkswagen ID.4. Removing and installing operating unit for memory settings [E464]/[E465]

Installing

Install in reverse order of removal, observing the following:

  • The operating unit for memory settings must be heard to engage.

Removing and installing wiring harness for seat frame

Special tools and workshop equipment required

  • release tool - T10236-
  • setting gauge - 3371-

If electrical wires are disconnected or removed and installed, it is useful to make corresponding drawings or photos. This guarantees that everything is re-installed in its original position.

Driver side seat position sensor - G553- and front passenger side seat position sensor - G554- are referred to hereafter as seat position sensor.

Removal and installation are described for left side of vehicle as an example.

Removing

  • ⇒ Rep. gr. 72 ; Secure front seat to seat repair stand .

Vehicles with seat position sensor

  • Unscrew bolt -2-.
  • Detach seat position sensor -1-.
Volkswagen ID.4. Removing and installing wiring harness for seat frame

All vehicles (continued)

  • Separate electrical connectors.
  • Use release tool - T10236- to unclip electrical wires.
  • Guide wiring harness for seat frame out of front seat, and remove it.

Installing

Install in reverse order of removal, observing the following:

  • Route electrical wire so that original wiring layout is restored

Vehicles with seat position sensor

  • Engage seat position sensor -1- in lower seat pan frame.
  • Place 4 mm plate from setting gauge - 3371- -4- between seat position sensor -1- and lower seat pan frame.
  • Tighten bolt -2-.
  • Remove setting gauge - 3371- -4-.
Volkswagen ID.4. Vehicles with seat position sensor

All vehicles (continued)

Tightening torques

  • ⇒ Rep. gr. 72 ; Assembly overview - seat pan