Valve unit of heat pump, R744

In this manual: Valve unit of heat pump, R744
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
19steps
~114min
4/5difficulty
0102030405086N·mlb·ft
Tightening torque found on this page
Done 0 of 19
  • Assembly overview - heat pump valve unit
  • Removing and installing heat pump valve unit
  • Removing and installing refrigerant expansion valve 1 N636
  • Removing and installing refrigerant expansion valve 2 N637
  • Removing and installing refrigerant shut-off valve 2 [N640]
  • Removing and installing refrigerant shut-off valve 4 [N642]

Assembly overview - heat pump valve unit

Volkswagen ID.4. Assembly overview - heat pump valve unit
  1. Guide sleeve
  • 3x
  1. Rubber bush
  • 3x
  1. Bolt
  • 11x
  • 8 N·m
  1. Bracket
  2. Bolt
  • 3x
  • 20 N·m
  1. Refrigerant expansion valve 1 - N636-
  • ⇒ Rep. gr. 87 ; Removing and installing refrigerant expansion valve 1 N636
  1. Refrigerant shut-off valve 1 - N696-
  • ⇒ Rep. gr. 87 ; Removing and installing refrigerant shut-off valve 1 N696
  1. Refrigerant expansion valve 3 - N638-
  • ⇒ Rep. gr. 87 ; Removing and installing refrigerant expansion valve 3 N638
  1. Refrigerant expansion valve 2 - N637-
  • ⇒ Rep. gr. 87 ; Removing and installing refrigerant expansion valve 2 N637
  1. Electrical wiring for refrigerant pressure and temperature sender 4 - G828-
  2. Refrigerant shut-off valve 5 - N643-
  • ⇒ Rep. gr. 87 ; Removing and installing refrigerant shut-off valve 5 N643
  1. Refrigerant shut-off valve 4 - N642-
  • ⇒ Rep. gr. 87 ; Removing and installing refrigerant shut-off valve 4 N642
  1. Electrical wiring for heat pump valve unit
  2. Refrigerant shut-off valve 2 - N640
  • ⇒ Rep. gr. 87 ; Removing and installing refrigerant shut-off valve 2 N640
  1. Refrigerant shut-off valve 3 - N641-
  • ⇒ Rep. gr. 87 ; Removing and installing refrigerant shut-off valve 3 N641
  1. Electrical wiring for refrigerant pressure and temperature sender 2 - G826-
  2. Electrical wiring for refrigerant pressure and temperature sender 5 - G829-
  3. High-voltage battery heat exchanger
  • ⇒ Rep. gr. 87 ; Removing and installing heat exchanger for high-voltage battery
  1. Dryer
  • ⇒ Rep. gr. 87 ; Removing and installing dryer
  1. Retainer
  2. Flexible joint
  • 3 N·m
  1. Nut
  • 15 N·m

Assembly overview - refrigerant lines inside heat pump valve unit

Volkswagen ID.4. Assembly overview - refrigerant lines inside heat pump valve unit
  1. Refrigerant line
  2. Bolt
  • Applies to all connections in illustration
  • Renew after removing
  • Hexagon bolt: 13 N·m
  • Twelve-point bolt: 5 N·m +90º
  1. Seal
  • Applies to all connections in illustration
  • Renew after removing
  1. Retaining element
  • Applies to all connections in illustration
  • Renew after removing
  1. Refrigerant line
  2. Dryer
  • ⇒ Rep. gr. 87 ; Removing and installing dryer
  1. Refrigerant line
  2. Refrigerant line
  3. Refrigerant line
  4. Heat pump valve unit
  • ⇒ Rep. gr. 87 ; Removing and installing heat pump valve unit
  1. High-voltage battery heat exchanger
  • ⇒ Rep. gr. 87 ; Removing and installing heat exchanger for high-voltage battery
  1. Refrigerant line

Assembly overview - refrigerant lines at heat pump valve unit

Volkswagen ID.4. Assembly overview - refrigerant lines at heat pump valve unit
  1. Refrigerant line
  • ⇒ Rep. gr. 87 ; Removing and installing refrigerant line between expansion valve N636/ N696 and heat condenser
  1. Refrigerant line
  • ⇒ Rep. gr. 87 ; Removing and installing refrigerant line between expansion valve N638/ N637 and evaporator
  1. Refrigerant line
  • ⇒ Rep. gr. 87 ; Removing and installing refrigerant line between condenser/gas cooler and refrigerant shut-off valve 2 N640
  1. High-voltage battery heat exchanger
  • ⇒ Rep. gr. 87 ; Removing and installing heat exchanger for high-voltage battery
  1. Refrigerant line
  • ⇒ Rep. gr. 87 ; Removing and installing refrigerant line between refrigerant shutoff valve 3 N641 and heat condenser
  1. Refrigerant line
  • ⇒ Rep. gr. 87 ; Removing and installing refrigerant line between air conditioner compressor VX81 and valve block N641/N640
  1. Retaining element
  • Applies to all connections in illustration
  • Renew after removing
  1. Seal
  • Applies to all connections in illustration
  • Renew after removing
  1. Bolt
  • Applies to all connections in illustration
  • Renew after removing
  • 5 N·m +90º
  1. Heat pump valve unit
  • ⇒ Rep. gr. 87 ; Removing and installing heat pump valve unit
  1. Refrigerant line
  • ⇒ Rep. gr. 87 ; Removing and installing refrigerant line between heat pump valve unit and evaporator

Removing and installing heat pump valve unit

Special tools and workshop equipment required

  • ESD workplace - VAS 6613-
  • engine bung set - VAS 6122-

Removing

Immediately seal open lines and connections with clean plugs from engine bung set - VAS 6122- .

When renewing several components of heat pump valve unit at the same time:

  • Observe procedure for renewing components in refrigerant circuit ⇒ General information - air conditioning systems with refrigerant R744; Rep. gr. 87 ; Renewing components .

Continued

  • Carry out function "Open electrically actuated valves to drain, evacuate or charge refrigerant circuit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .
  • ⇒ Air conditioning systems with refrigerant R744 - General notes; Rep. gr. 87 ; Working with air conditioner service station; Draining refrigerant circuit .
  • Remove lock carrier ⇒ General body repairs, exterior; Rep.

    gr. 50 ; Lock carrier; Removing and installing lock carrier .

  • ⇒ Rep. gr. 19 ; Cooling system/coolant; Draining coolant .
  • Remove air intake box of heater and air conditioning unit ⇒ Rep. gr. 87 ; Removing and installing air intake unit of heater and air conditioning unit .
  • Detach coolant expansion tank, and lay it aside ⇒ Rep.

    gr. 19 ; Cooling system/coolant; Removing and installing coolant expansion tank .

  • Remove front underbody cladding ⇒ General body repairs, exterior; Rep. gr. 66 ; Underbody cladding; Removing and installing front underbody cladding .
  • Separate coolant hose -1- and lay to one side.

CAUTION

Risk of frostbite from escaping pressurised refrigerant Risk of frostbite on skin and other parts of the body

  • Put on protective gloves.
  • Put on safety goggles.
  • Extract/drain refrigerant and then immediately open up refrigerant circuit.
  • Extract/drain refrigerant again if more than 10 minutes have passed since initial extraction and refrigerant circuit has not been opened up. Renewed evaporation has created pressure in the refrigerant circuit.
Volkswagen ID.4. Removing and installing heat pump valve unit
  • Unscrew bolt -2-.
  • Pull off refrigerant line -3-.

Right-hand drive vehicles:

  • Remove lock carrier bar ⇒ General body repairs, exterior; Rep. gr. 50 ; Lock carrier; Removing and installing lock carrier bar .
  • Remove air conditioner compressor ⇒ Rep. gr. 87 ; Removing and installing air conditioner compressor .

All vehicles (continued)

Left-hand drive vehicles:

  • Mark (to avoid interchanging) and disconnect electrical connector -3-.
  • Unscrew bolt -2-.
  • Pull off refrigerant line -1-.
Volkswagen ID.4. Removing and installing heat pump valve unit

All vehicles (continued)

  • Unscrew bolts -3-.
  • Pull off refrigerant line -1- and -2-, and collect escaping oil.

Important

  • Amount of refrigerating oil that has escaped must be taken into account when filling refrigerant circuit.
Volkswagen ID.4. Removing and installing heat pump valve unit
  • Loosen clamps -3-.
  • Pull off coolant hoses -1- and -2-.
Volkswagen ID.4. Removing and installing heat pump valve unit
  • Mark (to avoid interchanging) and disconnect electrical connectors -1- and -2-.
Volkswagen ID.4. Removing and installing heat pump valve unit
  • Unscrew bolts -1- through -4-.
  • Pull off refrigerant lines.
Volkswagen ID.4. Removing and installing heat pump valve unit
  • Unscrew bolts -2- through -4- from bracket of heat pump valve unit -1-.
Volkswagen ID.4. Removing and installing heat pump valve unit
  • Remove valve unit of heat pump -1- upwards.
Volkswagen ID.4. Removing and installing heat pump valve unit

NOTICE

Risk of damage to electrical components.

Electrostatic charge may damage electrical components.

  • Work on electrical components must always be carried out at an ESD workplace.
  • Place heat pump valve unit onto ESD workplace - VAS 6613- .

Installing

Install in reverse order of removal, observing the following:

  • Install seals and captive fasteners free of oil.

After renewal of several components of heat pump valve unit at the same time:

  • Carry out adaption routine for refrigerant oil capacity in refrigerant circuit ⇒ General information - air conditioning systems with refrigerant R744; Rep. gr. 87 ; Renewing components .

Continued

  • Carry out function "Open electrically actuated valves to drain, evacuate or charge refrigerant circuit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .
  • ⇒ Air conditioning systems with refrigerant R744 - General notes; Rep. gr. 87 ; Working with air conditioner service station; Charging refrigerant circuit .
  • ⇒ Rep. gr. 19 ; Cooling system/coolant; Filling cooling system

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - heat pump valve unit
  • ⇒ Rep. gr. 87 ; Assembly overview - refrigerant lines
  • ⇒ Rep. gr. 87 ; Assembly overview - air intake box of heater and air conditioning unit

Removing and installing refrigerant expansion valve 1 N636

Special tools and workshop equipment required

  • ESD workplace - VAS 6613-

Available versions

Variante A - up to approx. 10/2023, identifiable by pressure sender aligned horizontally in refrigerant line -1-

Variante B - as of approx. 11/2023, identifiable by pressure sender aligned vertically -2-

Volkswagen ID.4. Removing and installing refrigerant expansion valve 1 N636

Removing and installing, version A

Removing

Refrigerant expansion valve 1 - N636- and refrigerant shut-off valve 1 - N696- cannot be renewed individually.

  • Remove heat pump valve unit ⇒ Rep. gr. 87 ; Removing and installing heat pump valve unit .

NOTICE

Risk of damage to electrical components.

Electrostatic charge may damage electrical components.

  • Work on electrical components must always be carried out at an ESD workplace.
  • Place heat pump valve unit onto ESD workplace - VAS 6613- .
  • Unscrew bolts -1-, -2- and -3-.
Volkswagen ID.4. Removing and installing, version A
  • Mark (to avoid interchanging) and disconnect electrical connectors -2-.
  • Unscrew bolts -3-.
  • Remove refrigerant expansion valve 1 - N636- and refrigerant shut-off valve 1 - N696- -1-.
Volkswagen ID.4. Removing and installing, version A

Installing

Install in reverse order of removal, observing the following:

Install seals and captive fasteners free of oil.

When renewing expansion valve/shut-off valve:

  • Carry out function "Addressing routine for refrigerant valves" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - heat pump valve unit

Removing and installing, version B

Removing

Refrigerant expansion valve 1 - N636- and refrigerant shut-off valve 1 - N696- cannot be renewed individually.

  • Remove heat pump valve unit ⇒ Rep. gr. 87 ; Removing and installing heat pump valve unit .

NOTICE

Risk of damage to electrical components.

Electrostatic charge may damage electrical components.

  • Work on electrical components must always be carried out at an ESD workplace.
  • Place heat pump valve unit onto ESD workplace - VAS 6613- .
  • Unscrew bolts -1-, -2- and -3-.
Volkswagen ID.4. Removing and installing, version B
  • Mark (to avoid interchanging) and disconnect electrical connectors -2-.
  • Unscrew bolts -3-.
  • Remove refrigerant expansion valve 1 - N636- and refrigerant shut-off valve 1 - N696- -1-.
Volkswagen ID.4. Removing and installing, version B

Installing

Install in reverse order of removal, observing the following:

  • Install seals and captive fasteners free of oil.

When renewing expansion valve/shut-off valve:

  • Carry out function "Addressing routine for refrigerant valves" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - heat pump valve unit

Removing and installing refrigerant expansion valve 2 N637

Special tools and workshop equipment required

  • ESD workplace - VAS 6613-

Removing

Refrigerant expansion valve 2 - N637- and refrigerant expansion valve 3 - N638- cannot be renewed separately.

  • Remove heat pump valve unit ⇒ Rep. gr. 87 ; Removing and installing heat pump valve unit .

NOTICE

Risk of damage to electrical components.

Electrostatic charge may damage electrical components.

  • Work on electrical components must always be carried out at an ESD workplace.
  • Place heat pump valve unit on ESD workplace - VAS 6613- .
  • Remove bolts -1-, -2- and -3-.
Volkswagen ID.4. Removing and installing refrigerant expansion valve 2 N637
  • Mark electrical connectors -2- to avoid interchange and unplug them.
  • Remove bolts -3-.
  • Detach refrigerant expansion valve 2 - N637- and refrigerant expansion valve 3 - N638- -1-.
Volkswagen ID.4. Removing and installing refrigerant expansion valve 2 N637

Installing

Installation is carried out in reverse order; note the following:

  • Install seals and retaining elements, making sure they are free of oil.

If expansion valves have been renewed:

  • Perform function "Addressing refrigerant valves" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Starting diagnosis .

Continued

Tightening torques

  • ⇒ Rep. gr. 87 ; Exploded view - heat pump valve unit

Removing and installing refrigerant expansion valve 3 N638

Removing and installing

Refrigerant expansion valve 3 - N638- is removed together with refrigerant expansion valve 2 - N637- and cannot be renewed separately ⇒ Rep. gr. 87 ; Removing and installing refrigerant expansion valve 2 N637 .

Removing and installing refrigerant shut-off valve 1 N696

Removing and installing

Refrigerant shut-off valve 1 - N696- is removed together with refrigerant expansion valve 1 - N636- and cannot be renewed separately ⇒ Rep. gr. 87 ; Removing and installing refrigerant expansion valve 1 N636 .

Removing and installing refrigerant shut-off valve 2 [N640]

Special tools and workshop equipment required

  • ESD workplace - VAS 6613-
  • counterhold tool - T10630-

Available versions

Variante A - up to approx. 10/2023, identifiable by pressure sender aligned horizontally in refrigerant line -1-

Variante B - as of approx. 11/2023, identifiable by pressure sender aligned vertically -2-

Volkswagen ID.4. Removing and installing refrigerant shut-off valve 2 [N640]

Removing and installing, version A

Removing

Refrigerant shut-off valve 2 - N640- and refrigerant shut-off valve 3 - N641- cannot be renewed individually.

  • Remove heat pump valve unit ⇒ Rep. gr. 87 ; Removing and installing heat pump valve unit .

NOTICE

Risk of damage to electrical components.

Electrostatic charge may damage electrical components.

  • Work on electrical components must always be carried out at an ESD workplace.
  • Place heat pump valve unit onto ESD workplace - VAS 6613- .
  • Insert counterhold tool - T10630- -4-.
  • Unscrew bolts -1-, -2-, -3- and -5-.
  • Pull off refrigerant lines
Volkswagen ID.4. Removing and installing, version A
  • Mark (to avoid interchanging) and disconnect electrical connectors -2-.
  • Unscrew bolts -3-.
  • Remove refrigerant shut-off valve 2 - N640- and refrigerant shut-off valve 3 - N641- -1-.
Volkswagen ID.4. Removing and installing, version A

Installing

Install in reverse order of removal, observing the following:

  • Install seals and captive fasteners free of oil.
  • When tightening bolts -3-, use counterhold tool - T10630- .
Volkswagen ID.4. Removing and installing, version A

If shut-off valve have been renewed:

  • Carry out function "Addressing routine for refrigerant valves" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Tightening torques

⇒ Rep. gr. 87 ; Assembly overview - heat pump valve unit

Removing and installing, version B

Removing

Refrigerant shut-off valve 2 - N640- and refrigerant shut-off valve 3 - N641- cannot be renewed individually.

  • Remove heat pump valve unit ⇒ Rep. gr. 87 ; Removing and installing heat pump valve unit .

NOTICE

Risk of damage to electrical components.

Electrostatic charge may damage electrical components.

  • Work on electrical components must always be carried out at an ESD workplace.
  • Place heat pump valve unit onto ESD workplace - VAS 6613- .
  • Unscrew bolts -1-, -2-, -3- and -4-.
  • Remove refrigerant lines.
Volkswagen ID.4. Removing and installing, version B
  • Mark (to avoid interchanging) and disconnect electrical connectors -2-.
  • Unscrew bolts -3-.
  • Remove refrigerant shut-off valve 2 - N640- and refrigerant shut-off valve 3 - N641- -1-.
Volkswagen ID.4. Removing and installing, version B

Installing

  • Install seals and captive fasteners free of oil.

If shut-off valve have been renewed:

  • Carry out function "Addressing routine for refrigerant valves" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses

Tightening torques

  • Rep. gr. 87 ; Assembly overview - heat pump valve unit

Removing and installing refrigerant shut-off valve 3 N641

Removing and installing

Refrigerant shut-off valve 3 - N641- is removed together with refrigerant shut-off valve 2 - N640- and cannot be renewed separately ⇒ Rep. gr. 87 ; Removing and installing refrigerant shut-off valve 2 N640 .

Removing and installing refrigerant shut-off valve 4 [N642]

Special tools and workshop equipment required

  • ESD workplace - VAS 6613-

Available versions

Variante A - up to approx. 10/2023, identifiable by pressure sender aligned horizontally in refrigerant line -1-

Variante B - as of approx. 11/2023, identifiable by pressure sender aligned vertically -2

Volkswagen ID.4. Removing and installing refrigerant shut-off valve 4 [N642]

Removing and installing, version A

Removing

Refrigerant shut-off valve 4 - N642- and refrigerant shut-off valve 5 - N643- cannot be renewed individually.

  • Remove heat pump valve unit ⇒ Rep. gr. 87 ; Removing and installing heat pump valve unit .

NOTICE

Risk of damage to electrical components.

Electrostatic charge may damage electrical components.

  • Work on electrical components must always be carried out at an ESD workplace.
  • Place heat pump valve unit onto ESD workplace - VAS 6613- .
  • Unscrew bolts -2-, -3- and -4-.
  • Pull off refrigerant line -1-.
Volkswagen ID.4. Removing and installing, version A
  • Unscrew bolts -1- and -2-.
Volkswagen ID.4. Removing and installing, version A
  • Mark (to avoid interchanging) and disconnect electrical connectors -2-.
  • Unscrew bolts -3-.
  • Remove refrigerant shut-off valve 4 - N642- and refrigerant shut-off valve 5 - N643- -1-.
Volkswagen ID.4. Removing and installing, version A

Installing

Install in reverse order of removal, observing the following:

  • Install seals and captive fasteners free of oil.

If shut-off valve have been renewed:

  • Carry out function "Addressing routine for refrigerant valves" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - heat pump valve unit

Removing and installing, version B

Removing

Refrigerant shut-off valve 4 - N642- and refrigerant shut-off valve 5 - N643- -1- cannot be renewed individually.

  • Remove heat pump valve unit ⇒ Rep. gr. 87 ; Removing and installing heat pump valve unit .

NOTICE

Risk of damage to electrical components.

Electrostatic charge may damage electrical components.

  • Work on electrical components must always be carried out at an ESD workplace.
  • Place heat pump valve unit onto ESD workplace - VAS 6613- .
  • Unscrew bolts -2-, -3- and -4-.
  • Pull off refrigerant line -1-.
Volkswagen ID.4. Removing and installing, version B
  • Unscrew bolts -1- and -2-.
Volkswagen ID.4. Removing and installing, version B
  • Mark (to avoid interchanging) and disconnect electrical connectors -2-.
  • Unscrew bolts -3-.
  • Remove refrigerant shut-off valve 4 - N642- and refrigerant shut-off valve 5 - N643- -1-.
Volkswagen ID.4. Removing and installing, version B

Installing

Install in reverse order of removal, observing the following:

  • Install seals and captive fasteners free of oil.

If shut-off valve have been renewed:

  • Carry out function "Addressing routine for refrigerant valves" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - heat pump valve unit

Removing and installing refrigerant shut-off valve 5 N643

Removing and installing

Refrigerant shut-off valve 5 - N643- is removed together with refrigerant shut-off valve 4 - N642- and cannot be renewed separately ⇒ Rep. gr. 87 ; Removing and installing refrigerant shut-off valve 4 N642 .