Front heater and air conditioning unit, R744

In this manual: Front heater and air conditioning unit, R744
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
18steps
~108min
4/5difficulty
0102030405086N·mlb·ft
Tightening torque found on this page
Done 0 of 18
  • Assembly overview - heater and air conditioning unit
  • Assembly overview - air intake box of heater and air conditioning unit
  • Removing and installing heater and air conditioning unit
  • Removing and installing dust and pollen filter
  • Removing and installing fresh air blower control unit [J126]
  • Removing and installing condensation drain
  • Removing and installing air intake box of heater and air conditioning unit
  • Removing and installing air intake cowling
  • Removing and installing high voltage heater (PTC) [ZX17]

Assembly overview - heater and air conditioning unit

  1. Cover for high-voltage heater (PTC) - ZX17-
  2. High-voltage heater (PTC) - ZX17-
    Volkswagen ID.4. Assembly overview - heater and air conditioning unit
  • ⇒ Rep. gr. 87 ; Removing and installing high-voltage heater (PTC) ZX17
  1. Condensation drain
  • ⇒ Rep. gr. 87 ; Checking condensation drain
  • ⇒ Rep. gr. 87 ; Removing and installing condensation drain
  1. Potential equalisation line
  • ⇒ Electric drive motor; Rep. gr. 93 ; Potential equalisation lines; Overview of fitting locations - potential equalisation lines
  1. Nut
  • 8 N·m
  1. Bolt
  • 4x
  • 1,2 N·m
  1. Bolt
  • 3x
  • 1,2 N·m

Assembly overview - evaporator housing

Volkswagen ID.4. Assembly overview - evaporator housing
  1. Heater and air conditioning unit
  • ⇒ Rep. gr. 87 ; Assembly overview - heater and air conditioning unit
  • ⇒ Rep. gr. 87 ; Removing and installing heater and air conditioning unit
  1. Spacer

Renew after removing

  1. Evaporator
  • ⇒ Rep. gr. 87 ; Removing and installing evaporator
  1. Foam
  • Renew after removing
  1. Bolt
  • 2x
  • 1,2 N·m
  1. Cover for evaporator housing
  2. Condensation drain
  • ⇒ Rep. gr. 87 ; Checking condensation drain
  • ⇒ Rep. gr. 87 ; Removing and installing condensation drain
  1. Cover
  2. Cover
  3. Bolt
  • 2x
  • 1,2 N·m
  1. Heat condenser
  • With seal
  • ⇒ Rep. gr. 87 ; Removing and installing heat condenser

Assembly overview - air intake box of heater and air conditioning unit

Volkswagen ID.4. Assembly overview - air intake box of heater and air conditioning unit
  1. Cover for fresh air intake
  2. Fresh air intake
  • ⇒ Rep. gr. 87 ; Removing and installing fresh air intake
  1. Bolt
  • Observe tightening sequence ⇒ Rep.

    gr. 87 ; Removing and installing air intake cowling

  • 3x
  • 8 N·m
  1. Air intake cowling
  • See: "Mounting on air intake cowling for righthand drive vehicles"
  • ⇒ Rep. gr. 87 ; Removing and installing air intake cowling
  1. Nut
  • Observe tightening sequence ⇒ Rep.

    gr. 87 ; Removing and installing air intake cowling

  • 7x
  • 8 N·m
  1. Bolt
  • 4x
  • 1,2 N·m
  1. Cover
  2. Bolt
  • 3x
  • 1,2 N·m
  1. Fresh air blower control unit - J126-
  • ⇒ Rep. gr. 87 ; Removing and installing fresh air blower control unit J126
  1. Air intake box of heater and air conditioning unit
  • ⇒ Rep. gr. 87 ; Removing and installing air intake box of heater and air conditioning unit
  1. Nut
  • 5x
  • 3,5 N·m
  1. Bolt
  • ⇒ Rep. gr. 87 ; Assembly overview - control motors
  1. Control motor for fresh air and air recirculation flap - VX96-
  • With fresh air/air recirculation, air flow flap control motor - V425-
  • With potentiometer for fresh air/air recirculation, air flow flap control motor - G644-
  • ⇒ Rep. gr. 87 ; Removing and installing control motor for fresh air and air recirculation flap VX96
  1. Noise insulation
  2. Dust and pollen filter
  • ⇒ Rep. gr. 87 ; Removing and installing dust and pollen filter
  1. Dust and pollen filter
  • Depending on equipment/vehicle version
  • ⇒ Rep. gr. 87 ; Removing and installing dust and pollen filter
  1. Cover
  2. Bolt
  • Depending on equipment/vehicle version
  • 2 N·m
  1. Noise insulation
  2. Gasket
  3. Gasket

Mounting on air intake cowling for right-hand drive vehicles

Volkswagen ID.4. Assembly overview - air intake box of heater and air conditioning unit

Removing and installing heater and air conditioning unit

Special tools and workshop equipment required

  • engine bung set - VAS 6122-

Removing

Immediately seal open lines and connections with clean plugs from engine bung set - VAS 6122- .

If heater and air conditioning unit, evaporator or heat condenser has been renewed:

  • Observe procedure for renewing components in refrigerant circuit ⇒ General information - air conditioning systems with refrigerant R744; Rep. gr. 87 ; Renewing components .

Continued

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) de-energise the high-voltage system.
  • ⇒ Rep. gr. 93 ; De-energise high-voltage system .
  • Carry out function "Open electrically actuated valves to drain, evacuate or charge refrigerant circuit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .
  • ⇒ Air conditioning systems with refrigerant R744 - General notes; Rep. gr. 87 ; Working with air conditioner service station; Draining refrigerant circuit .
  • Remove air intake box of heater and air conditioning unit ⇒ Rep. gr. 87 ; Removing and installing air intake unit of heater and air conditioning unit .

CAUTION

Risk of frostbite from escaping pressurised refrigerant Risk of frostbite on skin and other parts of the body

  • Put on protective gloves.
  • Put on safety goggles.
  • Extract/drain refrigerant and then immediately open up refrigerant circuit.
  • Extract/drain refrigerant again if more than 10 minutes have passed since initial extraction and refrigerant circuit has not been opened up. Renewed evaporation has created pressure in the refrigerant circuit.
  • Unscrew bolts -1- through -4-.
  • Pull off refrigerant lines.
Volkswagen ID.4. Removing and installing heater and air conditioning unit
  • Remove dash panel cross member ⇒ General body repairs, interior; Rep. gr. 70 ; Dash panel cross member; Removing and installing dash panel cross member .
  • Remove rear footwell vent ⇒ Rep. gr. 87 ; Removing and installing rear footwell vent .
  • Detach air duct for rear centre console vent from heater and air conditioning unit ⇒ Rep. gr. 87 ; Removing and installing air duct for rear centre console vent .
  • Disconnect electrical connectors and electrical wire from heater and air conditioning unit.

NOTICE

Risk of damage to airbag control unit. Electrical connectors corrode when exposed to moisture.

  • After unplugging connectors for control unit, cover them or seal them off to prevent moisture from entering.
  • Place a cloth underneath condensation drain -1- to catch escaping condensate.
  • Pull condensation drain -2- off connection of heater and air conditioning unit -1- -arrow A-.
Volkswagen ID.4. Removing and installing heater and air conditioning unit
  • Disconnect electrical connector -7-.
  • Release retaining clip -5-.
  • Unscrew nut -8-, and detach potential equalisation line.
Volkswagen ID.4. Removing and installing heater and air conditioning unit

Important

  • The aid of an additional person is required for the subsequent work steps.
  • Remove heater and air conditioning unit -1-.
Volkswagen ID.4. Removing and installing heater and air conditioning unit

Installing

Install in reverse order of removal, observing the following:

If components of refrigerant circuit have been renewed:

  • Carry out adaption routine for refrigerant oil capacity in refrigerant circuit ⇒ General information - air conditioning systems with refrigerant R744; Rep. gr. 87 ; Renewing components .

Continued

  • Make sure that the condensation drain is properly seated ⇒ Rep. gr. 87 ; Removing and installing condensation drain .
  • Check screw connections of potential equalisation line, and clean them if necessary ⇒ Electrical system; Rep. gr. 97 ; Cleaning contact surfaces .

Important

  • Contact surfaces must be free of dirt, rust and grease.
  • Connect potential equalisation line, and tighten nut -8-.
  • Connect electrical connectors.
Volkswagen ID.4. Removing and installing heater and air conditioning unit
  • Install seals and captive fasteners free of oil.
  • Install air intake box of heater and air conditioning unit ⇒ Rep. gr. 87 ; Removing and installing air intake unit of heater and air conditioning unit .
  • Carry out function "Open electrically actuated valves to drain, evacuate or charge refrigerant circuit" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .
  • ⇒ Air conditioning systems with refrigerant R744 - General notes; Rep. gr. 87 ; Working with air conditioner service station; Charging refrigerant circuit .

WARNING

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) re-energise the high-voltage system.
  • ⇒ Rep. gr. 93 ; Re-energising high-voltage system .

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - refrigerant lines
  • ⇒ Rep. gr. 87 ; Assembly overview - heater and air conditioning unit
  • ⇒ Rep. gr. 87 ; Assembly overview - evaporator housing

Removing and installing evaporator

  • Evaporator is not available as a separate part ⇒ Electronic parts catalogue (ETKA) .

Dismantling and assembling heater and air conditioning unit

Heater and air conditioning unit must not be disassembled and reassembled separately ⇒ Electronic parts catalogue .

Removing and installing dust and pollen filter

Depending on the country, 2 dust and pollen filters -A- and -Bor 1 dust and pollen filter -B- may be installed.

Volkswagen ID.4. Removing and installing dust and pollen filter

Removing

  • Unscrew bolt -1-.
  • Release cover -2- -arrow-, and remove it.
Volkswagen ID.4. Removing and installing dust and pollen filter
  • Remove dust and pollen filter -1-.
Volkswagen ID.4. Removing and installing dust and pollen filter

Installing

  • Install in reverse order of removal, observing the following:
  • Observe installation position of dust and pollen filter.

Removing and installing fresh air blower control unit [J126]

Removing

  • Remove air intake box of heater and air conditioning unit ⇒ Rep. gr. 87 ; Removing and installing air intake unit of heater and air conditioning unit .
  • Unscrew bolts -2-.
  • Remove cover -1- in direction of -arrow-.
Volkswagen ID.4. Removing and installing fresh air blower control unit [J126]
  • Disconnect electrical connector -3-.
  • Unscrew bolts -2-.

CAUTION

Danger of burns due to hot cooling surface on fresh air blower control unit Take care not to burn your hands.

  • Put on protective gloves.
Volkswagen ID.4. Removing and installing fresh air blower control unit [J126]

NOTICE

Risk of damage to fresh air blower if handled incorrectly.

Risk of imbalance and operating problems.

  • Avoid any force or strain on fan wheel.
  • Do not move balancing weights on fan wheel.
  • Do not set fresh air blower down on fan wheel.
  • Remove fresh air blower control unit - J126- -1-.

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - air intake box of heater and air conditioning unit

Removing and installing evaporator temperature sensor [G308]

Removing

  • Remove tunnel support cover ⇒ General body repairs, interior; Rep. gr. 70 ; Dash panel; Removing and installing tunnel support cover .
  • Disconnect electrical connector -2-.
  • Remove evaporator temperature sensor - G308- -1- using commercially available plastic wedge -3-.
Volkswagen ID.4. Removing and installing evaporator temperature sensor [G308]

Installing

Install in reverse order of removal.

Removing and installing condensation drain

Removing

  • Remove floor covering ⇒ General body repairs, interior; Rep. gr. 70 ; Passenger compartment trim panels; Removing and installing floor covering .

NOTICE

Risk of damage to airbag control unit. Electrical connectors corrode when exposed to moisture.

  • After unplugging connectors for control unit, cover them or seal them off to prevent moisture from entering.
  • Place a cleaning cloth under connection for condensation drain -1- to catch escaping condensation.
  • Carefully pull condensation drain -2- off connection on heater and air conditioning unit -1-.
  • Take condensation drain -2- out of body opening -3-.
Volkswagen ID.4. Removing and installing condensation drain

Installing

Installation is carried out in reverse order; note the following:

Important

  • It must be possible to push condensation drain -2- onto connection of heater and air conditioning unit -1- without applying tension. Pay attention to retaining hook -arrow A-.
  • Sealing lip -4- must sit firmly on body opening -3- -arrow B-.
  • Fit condensation drain -2-, making sure to keep it straight.
  • Make sure that floor covering does not compress condensation drain -2-.
Volkswagen ID.4. Removing and installing condensation drain

Checking condensation drain

  • Remove floor covering ⇒ General body repairs, interior; Rep. gr. 70 ; Interior trim; Removing and installing floor covering .

NOTICE

Risk of damage to airbag control unit. Electrical connectors corrode when exposed to moisture.

  • After unplugging connectors for control unit, cover them or seal them off to prevent moisture from entering.
  • Check the condensation drain.

Important

  • Locking device -arrow A- must be engaged in connection on heater and air conditioning unit -1-.
  • Gasket -4- must sit firmly on body aperture -3- -arrow B-.
  • Condensation drain -2- must not be twisted or pinched.
  • Remove condensation drain -2- ⇒ Rep. gr. 87 ; Removing and installing condensation drain .
  • Check condensation drain -2- for bottleneck/blockage.
Volkswagen ID.4. Checking condensation drain

Installing

Install in reverse order.

Removing and installing air intake box of heater and air conditioning unit

Removing

  • Remove fresh air intake ⇒ Rep. gr. 87 ; Removing and installing fresh air intake .
  • Remove vibration isolation strut ⇒ General body repairs, exterior; Rep. gr. 50 ; Lock carrier; Removing and installing vibration isolation strut .
  • Release locking devices -3-.
  • Remove cover -2-.
  • Remove cover -1- from guide.
Volkswagen ID.4. Removing and installing air intake box of heater and air conditioning unit

Vehicles with all-wheel drive

  • Detach gearbox breather.

All vehicles (continued)

  • Disconnect electrical connectors -1-.
  • Release clamps -2-.
  • Lay electrical connector -3- to one side without disconnecting it.
Volkswagen ID.4. Removing and installing air intake box of heater and air conditioning unit
  • Unscrew fasteners -1-.
  • Remove adapter plate -2-.
Volkswagen ID.4. Removing and installing air intake box of heater and air conditioning unit
  • Unscrew nuts -2- from air intake box of heater and air conditioning unit -1-.
Volkswagen ID.4. Removing and installing air intake box of heater and air conditioning unit
  • Unscrew nuts -2- from air intake box of heater and air conditioning unit -1-.
  • Remove air intake box of heater and air conditioning unit -1-.
Volkswagen ID.4. Removing and installing air intake box of heater and air conditioning unit

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - air intake box of heater and air conditioning unit

Removing and installing air intake cowling

Removing

  • Remove air intake box ⇒ Rep. gr. 87 ; Removing and installing air intake box of heater and air conditioning unit .
  • Remove heater and air conditioning unit ⇒ Rep. gr. 87 ; Removing and installing heater and air conditioning unit .
  • Release fasteners -6- from grommet -5-.
  • Guide high-voltage wire -7- out of cowling -4-.
  • Unscrew bolts -1- to -3-.
Volkswagen ID.4. Removing and installing air intake cowling
  • Remove nuts -1- to -7-.
  • Detach air intake cowling -8-.
Volkswagen ID.4. Removing and installing air intake cowling

Installing

Installation is carried out in reverse order; note the following:

NOTICE

Water entering into heater and air conditioning unit and interior due to damaged gaskets/seals.

  • Fit gaskets/seals correctly.
  • Check gaskets/seals for damage.
  • Check seal -9- for damage.
  • Tighten nuts in sequence -1- to -7-.
Volkswagen ID.4. Removing and installing air intake cowling
  • Tighten bolts in sequence -1- to -3-.
  • Guide high-voltage wire -7- through opening in air intake cowling -4-, making sure it is routed correctly.
  • Clip in fasteners -6- of grommet -5-.
Volkswagen ID.4. Removing and installing air intake cowling

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - air intake box of heater and air conditioning unit
  • ⇒ Rep. gr. 87 ; Assembly overview - heater and air conditioning unit

Removing and installing high voltage heater (PTC) [ZX17]

Removing

DANGER

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) de-energise the high-voltage system.
  • ⇒ Rep. gr. 93 ; De-energise high-voltage system .
  • Remove tunnel support cover ⇒ General body repairs, interior; Rep. gr. 70 ; Dash panel; Removing and installing tunnel support cover .

Left-hand drive vehicles

  • Remove footwell vent on front passenger side ⇒ Rep.

    gr. 87 ; Removing and installing footwell vent on front passenger side .

  • Remove accelerator pedal module ⇒ Engine; Rep. gr. 93 ; Accelerator mechanism; Removing and installing accelerator pedal module [GX2] .

All vehicles (continued)

Right-hand drive vehicles

  • Remove footwell vent on driver side ⇒ Rep. gr. 87 ; Removing and installing footwell vent on driver side .
  • Remove footrest ⇒ General body repairs, interior; Rep.

    gr. 70 ; Trims, interior; Removing and installing footrest .

All vehicles (continued)

  • Disconnect electrical connector -4-.
  • Unscrew bolts -2- and -3- from high-voltage heater (PTC) - ZX17- -1-.
Volkswagen ID.4. Removing and installing high voltage heater (PTC) [ZX17]
  • Disconnect electrical connector -7-.
  • Release retaining clip -5-.
  • Unscrew nut -8-.
  • Detach potential equalisation line.
  • Unscrew bolts -2-, -3-, -4-, -6- and -9- from cover -1- and high-voltage heater (PTC) - ZX17- .
Volkswagen ID.4. Removing and installing high voltage heater (PTC) [ZX17]
  • Pull high-voltage heater (PTC) - ZX17- -1- as far as possible downwards out heater and air conditioning unit -arrow A-.
  • Loosen cover of heat condenser -2- in direction of -arrow B-, and remove it from upper holder towards side.
Volkswagen ID.4. Removing and installing high voltage heater (PTC) [ZX17]
  • Break off locking element -1- on heater and air conditioning unit.
  • Press down floor covering as far as possible.
  • Remove high-voltage heater (PTC) - ZX17- -2- in direction of -arrow
Volkswagen ID.4. Removing and installing high voltage heater (PTC) [ZX17]

Installing

Install in the reverse sequence of removal, observing the following:

Important

  • Contact surfaces must be free of dirt, rust and grease.
  • Check screw connections of potential equalisation line, and clean them if soiled ⇒ Electrical system; Rep. gr. 97 ; Cleaning contact surfaces .
  • Fit potential equalisation line.
  • Tighten nut -8-.
Volkswagen ID.4. Removing and installing high voltage heater (PTC) [ZX17]

WARNING

High voltage can cause fatal injury.

Danger of severe or fatal injuries from electric shock or electric arcs.

  • Have a high-voltage technician (HVT) or a high-voltage expert (HVE) re-energise the high-voltage system.
  • ⇒ Rep. gr. 93 ; Re-energising high-voltage system .

Tightening torques

  • ⇒ Rep. gr. 87 ; Assembly overview - heater and air conditioning unit
  • ⇒ Rep. gr. 87 ; Assembly overview - air ducts and air distribution in passenger compartment