Compartments/covers

In this manual: Compartments/covers
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
2steps
~12min
1/5difficulty
010203040501.51N·mlb·ft
Tightening torque found on this page
Done 0 of 2
  • Overview of fitting locations - storage compartments/covers/trim panels
  • Assembly overview dash panel cover on driver side
  • Assembly overview - dash panel cover (passenger side)
  • Assembly overview - glove compartment
  • Removing and installing dash panel cover on driver side
  • Removing and installing gap cover for dash panel insert
  • Removing and installing lower steering column trim
  • Removing and installing glove compartment with dash panel trim
  • Removing and installing glove compartment cover
  • Service position of glove compartment

Overview of fitting locations - storage compartments/covers/trim panels

The overview shows a left-hand drive vehicle as an example.

Volkswagen ID.4. Overview of fitting locations - storage compartments/covers/trim panels
  1. Dash panel
  • ⇒ Rep. gr. 70 ; Assembly overview - dash panel
  • ⇒ Rep. gr. 70 ; Removing and installing dash panel
  1. Cover for dash panel/cover for head-up display
  • ⇒ Rep. gr. 70 ; Removing and installing cover for dash panel/ head-up display
  1. Information electronics cover
  • ⇒ Rep. gr. 68 ; Removing and installing information electronics cover
  1. Dash panel trim on front passenger side
  • ⇒ Rep. gr. 70 ; Removing and installing dash panel trim
  1. Glove compartment with dash panel trim
  • ⇒ Rep. gr. 68 ; Assembly overview - dash panel cover (passenger side)
  • ⇒ Rep. gr. 68 ; Removing and installing glove compartment with dash panel trim
  1. Glove compartment cover
  • ⇒ Rep. gr. 68 ; Assembly overview - glove compartment
  • ⇒ Rep. gr. 68 ; Removing and installing glove compartment cover
  1. Centre console
  • ⇒ Rep. gr. 68 ; Assembly overview - centre console
  • ⇒ Rep. gr. 68 ; Removing and installing centre console
  1. Tunnel support cover
  • ⇒ Rep. gr. 70 ; Removing and installing tunnel support cover
  1. Steering column trim
  • Upper and lower
  • ⇒ Rep. gr. 68 ; Assembly overview - steering column trim
  • ⇒ Rep. gr. 68 ; Removing and installing upper steering column trim
  • ⇒ Rep. gr. 68 ; Removing and installing lower steering column trim
  1. Driver side footwell cover
  • ⇒ Rep. gr. 68 ; Removing and installing footwell cover (driver side)
  1. Dash panel cover on driver side
  • ⇒ Rep. gr. 68 ; Assembly overview - dash panel cover (driver side)
  • ⇒ Rep. gr. 68 ; Removing and installing dash panel cover on driver side
  1. Dash panel trim on driver side
  • ⇒ Rep. gr. 70 ; Removing and installing dash panel trim

Assembly overview dash panel cover on driver side

Assembly overview dash panel cover on driver side, left-hand drive vehicles

Volkswagen ID.4. Assembly overview ? dash panel cover on driver side, left-hand drive vehicles
  1. Dash panel end cover
  • ⇒ Rep. gr. 70 ; Removing and installing dash panel end cover
  1. Retaining clip
  • Qty. 2
  1. Dash panel cover on driver side
  • ⇒ "2.6.1 Removing and installing dash panel cover on driver side, left-hand drive vehicles", page 9
  1. Bolt
  • Qty. 3
  • 1,5 N·m
  1. Fuse box cover
  2. Spreader rivet
  • Qty. 3
  1. Driver side footwell cover
  • ⇒ Rep. gr. 68 ; Removing and installing footwell cover on driver side

Assembly overview dash panel cover on driver side, right-hand drive vehicles

Volkswagen ID.4. Assembly overview ? dash panel cover on driver side, right-hand drive vehicles
  1. Dash panel cover on driver side
  • ⇒ "2.6.2 Removing and installing dash panel cover on driver side, right-hand drive vehicles", page 10
  1. Bolt
  • Qty. 2
  • 1,5 N·m
  1. Retaining clip
  • Qty. 2
  1. Dash panel end cover
  • ⇒ Rep. gr. 70 ; Removing and installing dash panel end cover
  1. Spreader rivet
  • Qty. 3
  1. Driver side footwell cover
  • ⇒ Rep. gr. 68 ; Removing and installing footwell cover on driver side

Assembly overview - dash panel cover (passenger side)

The overview shows a left-hand drive vehicle as an example.

Volkswagen ID.4. Assembly overview - dash panel cover (passenger side)
  1. Glove compartment with dash panel trim
  • ⇒ Rep. gr. 68 ; Removing and installing glove compartment with dash panel trim
  1. Bolt
  • Qty. 7
  • 1,5 N·m
  1. Glove compartment cover
  • ⇒ Rep. gr. 68 ; Removing and installing glove compartment cover

Assembly overview - steering column trim

The overview shows a left-hand drive vehicle as an example.

Volkswagen ID.4. Assembly overview - steering column trim
  1. Gap cover for dash panel insert
  • ⇒ Rep. gr. 68 ; Removing and installing gap cover for dash panel insert
  1. Upper steering column trim
  • ⇒ Rep. gr. 68 ; Removing and installing upper steering column trim 3 - Lower steering column trim ❑ ⇒ Rep. gr. 68 ; Removing and installing lower steering column trim
  1. Bolt
  • 2,5 N·m
  1. Steering column electronics control unit - J527-
  • ⇒ Electrical system; Rep. gr. 94 ; Steering column switch module; Removing and installing steering column electronics control unit [J527]

Assembly overview - glove compartment

The overview shows a left-hand drive vehicle as an example.

Volkswagen ID.4. Assembly overview - glove compartment
  1. Glove compartment with dash panel trim
  • ⇒ Rep. gr. 68 ; Assembly overview - dash panel cover (passenger side)
  • ⇒ Rep. gr. 68 ; Removing and installing glove compartment with dash panel trim
  1. Bolt
  • Qty. 4
  • 1,5 N·m
  1. Glove compartment cover
  • ⇒ Rep. gr. 68 ; Removing and installing glove compartment cover
  1. Restrictor in glove compartment
  • ⇒ Rep. gr. 68 ; Removing and installing restrictor for glove compartment
  1. Glove compartment cover
  • ⇒ Rep. gr. 68 ; Removing and installing glove compartment cover
  • ⇒ Rep. gr. 68 ; Service position of glove compartment
  1. Glove compartment opener
  • ⇒ Rep. gr. 68 ; Removing and installing glove compartment opener
  1. Bolt
  • 1,5 N·m

Removing and installing dash panel cover on driver side

Removing and installing dash panel cover on driver side, left-hand drive vehicles

Removing

  • Remove dash panel end cover on driver side ⇒ Rep.

    gr. 70 ; Removing and installing dash panel end cover .

  • Unclip fuse box cover -3-.
  • Unscrew bolts -2-.
  • Release dash panel cover on driver side -1-.
  • Disconnect electrical connector.
  • Remove dash panel cover on driver side -1-.
Volkswagen ID.4. Removing and installing dash panel cover on driver side

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ "2.2.1 Assembly overview dash panel cover on driver side, left-hand drive vehicles",

Removing and installing dash panel cover on driver side, right-hand drive vehicles

Removing

  • Remove dash panel end cover on driver side ⇒ Rep. gr. 70 ; Removing and installing dash panel end cover .
  • Unscrew bolts -2-.
  • Release dash panel cover on driver side -1-.
  • Disconnect electrical connector.
  • Remove dash panel cover on driver side -1-.
Volkswagen ID.4. Removing and installing dash panel cover on driver side, right-hand drive vehicles

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ "2.2.2 Assembly overview dash panel cover on driver side, right-hand drive vehicles",

Removing and installing gap cover for dash panel insert

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

  • Pull out steering wheel as far as possible, and move it to lowest position. Use the full range of the steering column adjustment for this purpose.
  • Unclip gap cover for dash panel insert -2- together with dash panel trim on driver side -1- using commercially available plastic wedge.
Volkswagen ID.4. Removing and installing gap cover for dash panel insert

Installing

Install in reverse sequence of removal.

Removing and installing upper steering column trim

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

  • Remove steering wheel ⇒ Running gear, axles, steering; Rep. gr. 48 ; Steering wheel; Removing and installing steering wheel .
  • Using commercially available plastic wedge, lever upper steering column trim -2- in direction of -arrow- off steering column electronics control unit - J527- -1-.
Volkswagen ID.4. Removing and installing upper steering column trim

Installing

Install in reverse sequence of removal.

Removing and installing lower steering column trim

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

Remove upper steering column trim ⇒ Rep. gr. 68 ; Removing and installing upper steering column trim .

  • Unscrew bolt -2-.
  • Swing lower steering column trim -1- in direction of -arrow A-, and unclip it.
  • Disconnect electrical connector.
  • Remove lower steering column trim -1- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing lower steering column trim

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 68 ; Assembly overview - steering column trim

Removing and installing glove compartment opener

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

  • Open glove compartment cover.
  • Unscrew bolt -3-.
  • Push glove compartment opener -2- in direction of -arrow A-.
  • Remove glove compartment opener -2- together with mounting frame -1- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing glove compartment opener

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 68 ; Assembly overview - glove compartment

Removing and installing glove compartment with dash panel trim

Glove compartment with dash panel trim will henceforth be referred to as "glove compartment".

Removal and installation are described for a left-hand drive vehicle as an example.

  • Remove dash panel end cover ⇒ Rep. gr. 70 ; Removing and installing dash panel end cover .
  • Remove glove compartment cover ⇒ Rep. gr. 68 ; Removing and installing glove compartment cover .
  • Remove dash panel trim on front passenger side ⇒ Rep.

    gr. 70 ; Removing and installing dash panel trim .

  • Remove centre vent ⇒ Rep. gr. 70 ; Removing and installing steering centre vent .
  • Remove dash panel trim on driver side ⇒ Rep. gr. 68 ; Removing and installing dash panel trim on driver side .
  • Remove tunnel support cover ⇒ Rep. gr. 70 ; Removing and installing tunnel support cover .
  • Unscrew bolts -2-.
  • Remove glove compartment -1-.
Volkswagen ID.4. Removing and installing glove compartment with dash panel trim
  • Disconnect electrical connectors.

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 68 ; Assembly overview - dash panel cover (passenger side)

Removing and installing glove compartment cover

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

  • Bring glove compartment cover to service position ⇒ Rep.

    gr. 68 ; Glove compartment, service position .

  • Push centring pins -3- in direction of -arrow-, and remove glove compartment cover -1- from glove compartment with dash panel trim -2-.
Volkswagen ID.4. Removing and installing glove compartment cover

Installing

Install in reverse order of removal.

Removing and installing glove compartment cover

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

  • Remove glove compartment cover ⇒ Rep. gr. 68 ; Removing and installing glove compartment cover .
  • Unscrew bolts -1-.
  • Remove glove compartment cover -2-.
Volkswagen ID.4. Removing and installing glove compartment cover

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 68 ; Assembly overview - glove compartment

Removing and installing restrictor for glove compartment

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

  • Bring glove compartment cover to service position ⇒ Rep.

    gr. 68 ; Glove compartment, service position .

  • Disconnect electrical connector -3-.
  • Twist restrictor -2- in direction of -arrow-.
  • Remove restrictor -2-.
Volkswagen ID.4. Removing and installing restrictor for glove compartment

Installing

Install in reverse order of removal.

Service position of glove compartment

Moving to service position

  • Open glove compartment cover -2-.
  • Push buffer stops -1- in direction of -arrow A-, and fold out glove compartment cover -2- as far as stop in direction of -arrow B-.
  • Unclip push rod from restrictor at side of glove compartment cover -2-.
Volkswagen ID.4. Service position of glove compartment

Moving from service position

  • Slowly close glove compartment cover until cover can be heard to engage.

Removing and installing information electronics cover

Removing

  • Use commercially available plastic wedge to unclip -arrowsinformation electronics cover -1-.
Volkswagen ID.4. Removing and installing information electronics cover

Installing

Install in reverse order of removal.

Removing and installing footwell cover on driver side

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

  • Pull out spreader rivets -2-.
  • Remove footwell cover on driver side -1-.
Volkswagen ID.4. Removing and installing footwell cover on driver side

Installing

Install in reverse order of removal, observing the following:

  • Make sure that footwell cover on driver side is properly engaged in guide.