Front airbag, driver side
In this manual: Front airbag, driver side
~3min read
Assembly overview - front airbag, driver side
- Steering wheel
- ⇒ Running gear, axles, steering; Rep.
gr. 48 ; Steering wheel; Removing and installing steering wheel
- Airbag unit
- With driver side airbag igniter - N95- .
- ⇒ Rep. gr. 69 ; Removing and installing airbag unit with airbag igniter on driver side [N95]
- Wire
- ⇒ Rep. gr. 69 ; Renewing connector on airbag

- Removing and installing airbag unit with igniter
- Renewing connector on airbag
Removing and installing airbag unit with igniter
Special tools and workshop equipment required
- release tool - T10610-
Airbag unit with airbag igniter on driver side - N95- is referred to hereafter as airbag unit.
Removing
- Deactivate vehicle's drive system.
- Turn steering wheel 90º from straight-ahead position.
- Insert release tool - T10610- -1- as far as stop into opening for locking bracket -2-.
- Pull release tool - T10610- -1- in direction of -arrow- and release locking bracket -2-.

- Turn steering wheel 180º.
- Repeat release procedure.
- Apply light pressure onto airbag unit in order to relieve tension from locking bracket.
- Bring steering wheel to straight-ahead position.
- Disconnect battery earth cable ⇒ Electrical system; Rep.
gr. 27 ; Battery; Disconnecting and connecting battery .
CAUTION
It is possible to trigger pyrotechnic components unintentionally.
Risk of injury
- Discharge static electricity by briefly touching door striker plate.

- Detach airbag unit -3- to gain access to electrical connector -1-.
- Pull out connector lock -2- in direction of -arrow-, press it down, and disconnect electrical connector -1-.
Installing
Install in reverse order of removal, observing the following:
CAUTION
It is possible to trigger pyrotechnic components unintentionally.
Risk of injury
- Discharge static electricity by briefly touching door striker plate.
- Ft electrical connector, and push it in until it audibly engages.
- Secure electrical connector on backside of airbag unit.
- Make sure that no wires are trapped.
- Bring steering wheel to straight-ahead position.
- Position airbag unit -1- in steering wheel and press on edge with both hands simultaneously until it audibly engages.
- Connect battery earth cable ⇒ Electrical system; Rep.
gr. 27 ; Battery; Disconnecting and connecting battery .
CAUTION
It is possible to trigger pyrotechnic components unintentionally.
Risk of injury.
- Stay as far back as possible from pyrotechnic components when switching on the ignition.
- Switch on ignition.
- Read and clear event memory using ⇒ Vehicle diagnostic tester.

Renewing connector on airbag
Removing
The airbag unit with airbag igniter on driver side - N95- will henceforth be referred to as "airbag unit with igniter".
- Remove airbag unit with igniter ⇒ Rep. gr. 69 ; Removing and installing airbag unit with airbag igniter on driver side [N95] .
CAUTION
It is possible to trigger pyrotechnic components unintentionally.
Risk of injury
- Discharge static electricity by briefly touching door striker plate.
- Unhook electrical wire -1- from retainers on airbag -2-.

- Release connector lock -2- in direction of -arrow-.
- Disconnect electrical connector -1-.

- Detach electrical wire.
Installing
CAUTION
It is possible to trigger pyrotechnic components unintentionally.
Risk of injury
- Discharge static electricity by briefly touching door striker plate.
- Connect electrical connector -1- for airbag unit with igniter in direction of -arrow A-.
- Press in connector lock -2- in direction of -arrow B-.
Continue installation in reverse order of removal, observing the following:
- Connect electrical connectors until they engage audibly.

Was this page helpful?