Door

In this manual: Door
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
2steps
~12min
1/5difficulty
010203040502015N·mlb·ft
Tightening torque found on this page
Done 0 of 2
  • Assembly overview - door
  • Removing and installing inner door seal
  • Removing and installing outer door seal
  • Removing and installing door
  • Adjusting door
  • Adjusting striker pin
  • Removing and installing door hinge
  • Removing and installing door arrester

Assembly overview - door

Overview is shown for left side of vehicle as an example

Volkswagen ID.4. Assembly overview - door
  1. Door
  • ⇒ Rep. gr. 57 ; Removing and installing door
  • ⇒ Rep. gr. 57 ; Adjusting door
  1. Bolt
  • Renew after removing
  • 20 N·m +90º
  1. Lower section of door hinge
  • ⇒ Rep. gr. 57 ; Removing and installing door hinge
  1. Bolt
  • Renew after removing
  • 20 N·m +90º
  1. Threaded pin
  • 27 N·m
  1. Cap
  2. Bolt
  • 50 N·m
  1. Upper section of door hinge
  • ⇒ Rep. gr. 57 ; Removing and installing door hinge
  1. Bolt
  • Qty. 2
  • 8 N·m
  1. Door arrester
  • ⇒ Rep. gr. 57 ; Removing and installing door arrester
  1. Bolt
  • 30 N·m
  1. Bolt
  • Qty. 2
  • Specified torque and tightening sequence
  1. Striker pin
  • ⇒ Rep. gr. 57 ; Removing and installing striker pin
  • ⇒ Rep. gr. 57 ; Adjusting striker pin
  1. Bolt
  • Renew after removing
  • 20 N·m +90º
  1. Lower section of door hinge
  • ⇒ Rep. gr. 57 ; Removing and installing door hinge
  1. Bolt
  • Renew after removing
  • 20 N·m +90º
  1. Bolt
  • 50 N·m
  1. Upper section of door hinge
  • ⇒ Rep. gr. 57 ; Removing and installing door hinge

Specified torque and tightening sequence

Volkswagen ID.4. Assembly overview - door

Assembly overview - door seals

  1. Door joint seal
  • Renew after removing
  • ⇒ Rep. gr. 57 ; Removing and installing outer door seal
  1. Inner door seal
  • Renew after removing
  • ⇒ Rep. gr. 57 ; Removing and installing inner door seal
  1. Door
Volkswagen ID.4. Assembly overview - door seals

Removing and installing inner door seal

For reasons of clarity, the front door is not shown in the illustrations of the following work procedures.

Removal and installation are described for left side of vehicle as an example.

Removing

  • Remove front sill panel moulding ⇒ General body repairs, interior; Rep. gr. 70 ; Trims, interior; Removing and installing front sill panel moulding .
  • Remove upper A-pillar trim ⇒ General body repairs, interior; Rep. gr. 70 ; Trims, interior; Removing and installing A-pillar trim .
  • Remove lower A-pillar trim ⇒ General body repairs, interior; Rep. gr. 70 ; Trims, interior; Removing and installing lower A-pillar trim .
  • Remove upper B-pillar trim ⇒ General body repairs, interior; Rep. gr. 70 ; Trims, interior; Removing and installing B-pillar trim .
  • Remove lower B-pillar trim ⇒ General body repairs, interior; Rep. gr. 70 ; Trims, interior; Removing and installing lower B-pillar trim .
  • Pull off inner door seal -1- from body flange -2-.
Volkswagen ID.4. Removing and installing inner door seal

Installing

NOTICE

When the inner door seal is pulled off, the flanks of the seal may get bent up so that the inner door seal no longer provides the required sealing function at some points.

Water ingress or wind noise may result.

  • If the inner door seal has only been pulled off partially, compress the seal flanks, then install the inner door seal.
  • Make sure that adjacent trims are located in the beading of the inner door seal.
  • Start installing inner door seal -1- at top radius -arrow- of body flange -2-.

Important

  • Do not kink vulcanised point -3-.
  • Align vulcanised point -3- with threaded connection of door arrester.
  • Apply inner door seal -1- in lower area using plastic hammer.
  • Apply inner door seal -1- in upper area by hand.
Volkswagen ID.4. Removing and installing inner door seal

Continue installation in reverse order of removal.

Removing and installing outer door seal

Special tools and workshop equipment required

  • gasket shears - VAS 211 011-
  • punch tool - VAS 895 025-
  • roller - T40400-

Removal and installation are described for the left side of vehicle as an example.

Important

  • Instructions and specifications regarding temperature, minimum drying time, removal of adhesive residue and cleaning must be adhered to ⇒ General information - body; Rep.gr. 52 ; Self-adhesive components; Specifications for selfadhesive components .

Removing

  • Mark position of outer door seal -1- all around with adhesive tape -2-.
Volkswagen ID.4. Removing and installing outer door seal

NOTICE

Risk of damage to surfaces of components.

  • Mask off A-pillar in area of door arrester using commercially available adhesive tape.
  • Unscrew bolt -2- of door arrester -1-.
Volkswagen ID.4. Removing and installing outer door seal
  • Stretch outer door seal -1- incrementally in direction of -arrow A-.

Note

Stretching weakens bond of outer door seal.

  • Pull off outer door seal -1- in direction of -arrow B-.
  • Pull off outer door seal -1-.
Volkswagen ID.4. Removing and installing outer door seal

Installing

Install in reverse order of removal, observing the following:

If door is to be renewed

  • Copy bonding path of outer door seal from opposite door.

All vehicles (continued)

  • Starting below door arrester, mark water drain holes -1- on outer door seal -2- ⇒ "3.1 Dimensions of water drain holes in outer door seal"
Volkswagen ID.4. Removing and installing outer door seal
  • Remove adhesive residue, and clean bonding surfaces ⇒ General information - body; Rep. gr. 52 ; Self-adhesive components; Specifications for self-adhesive components .

NOTICE

Risk of damage to the door outer seal.

  • Do not stretch or compress the door outer seal.
  • Start installing door outer seal -1- below door arrester -arrow-.
  • Fir door outer seal -1- according to markings made before removal.
  • Pull off backing from outer door seal -1- all around incrementally.
  • Press on outer door seal -1- all around incrementally.
Volkswagen ID.4. Removing and installing outer door seal
  • Lay upper end of outer door seal -1- over lower end and mark joining point.
  • Cut outer door seal -1- flush at joining point using gasket shears - VAS 211 011- -2-.
Volkswagen ID.4. Removing and installing outer door seal

NOTICE

Risk of damage to the outer door seal when rolling on.

  • Only roll on outer door seal in area of adhesive tape.
  • With a force of at least 40 N on roller - T40400- -2-, fit outer door seal -1- in direction of -arrow B- in area of adhesive tape -3-. Press profile of outer door seal in direction of -arrow A- when doing this.

Important

Observe deviating minimum curing period:

  • Observe minimum curing period of 12 hours with door open.
Volkswagen ID.4. Removing and installing outer door seal
  • Use punch tool - VAS 895 025- -3- to punch water drain holes -1- and -2- at previously made markings.
Volkswagen ID.4. Removing and installing outer door seal

Tightening torques

  • ⇒ Rep. gr. 57 ; Assembly overview - door

Removing and installing door

Special tools and workshop equipment required

  • wedge - T10383/1-

Removing

Removal and installation are described for left side of vehicle as an example.

  • Disconnect battery earth cable ⇒ Electrical system; Rep. gr. 27 ; Battery; Disconnecting and connecting battery .
  • Push in wedge - T10383/1- -2- in direction of -arrow A- between boot -4- and locking element -3-.
  • Push locking element -3- in direction of -arrow B- using wedge - T10383/1- -1-, and disconnect boot -4- with electrical connector in direction of -arrow C-.
Volkswagen ID.4. Removing and installing door
  • Remove caps.
  • Loosen threaded pins -2-.
Volkswagen ID.4. Removing and installing door
  • Unscrew bolt -3-.

NOTICE

Risk of damage to the corrosion protection measures due to scratches.

The door arrester can damage the paint when lifting the door out and in.

  • Push door arrester into door.
Volkswagen ID.4. Removing and installing door
  • Push door arrester -2- inwards in direction of -arrow A- into door -1-.
  • Lift out door -1- in direction of -arrow A- by detaching upper sections of door hinges -2- from lower sections of door hinges -3-.
Volkswagen ID.4. Removing and installing door

Installing

Install in reverse order of removal, observing the following:

If a new door is installed, damping must be fitted on the outer door panel on the inside.

Position and dimensions ⇒ Rep. gr. 57 ; Assembly overview - door components .

  • Install damping for outer door panel on inside ⇒ General information - body; Rep. gr. 52 ; General operations; Removing and installing damping for outer door panel on inside .

All vehicles (continued)

NOTICE

Risk of damage to the corrosion protection measures due to scratches.

The door arrester can damage the paint when lifting the door out and in.

  • Push door arrester into door.
  • Hang door.

Important

  • Once the door is attached, the upper and lower door hinge sections must be flush with each other.
  • ⇒ Rep. gr. 57 ; Adjust door .
  • Adapt window regulator motor ⇒ Maintenance ; Booklet Elektrische Fensterheber: Positionierung prüfen

Tightening torques

  • ⇒ Rep. gr. 57 ; Assembly overview - door

Adjusting door

Adjusting door, left-hand drive vehicles

Special tools and workshop equipment required

  • door alignment tool - 3320-
  • setting gauge - 3371-

Preparation

Important

  • The vehicle must be standing on its wheels and on a level surface to ensure proper adjustment of the door.
  • The door must engage in the striker pin without excessive force.

The door is correctly adjusted when the following applies in closed condition:

  • The gaps are even.
  • The contours are flush with each other.
  • The door does not protrude too far inwards or outwards.

Adjusting shut lines

Left side of vehicle

  • Release and lower fuse holder C - SC- ⇒ Electrical system; Rep. gr. 97 ; Relay carriers, fuse holders, electronics boxes; Removing and installing fuse holder C [CS] .

All vehicles (continued)

Right-hand side of vehicle

  • Remove glove compartment ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing glove compartment .

All vehicles (continued)

  • Remove lower A-pillar trim ⇒ General body repairs, interior; Rep. gr. 70 ; Trims, interior; Removing and installing lower A-pillar trim .
  • Loosen bolts -1-, -2-, -3- and -4-.
  • Check gaps with setting gauge - 3371- , observing ⇒ Rep. gr. 00 ; centre gaps while doing so.
  • Tighten bolts -1-, -2-, -3- and -4-.
Volkswagen ID.4. Adjusting door

Adjusting flushness

  • Use door alignment tool - 3320- and corresponding socket to loosen bolts -1- and -2-.
  • Check gaps with setting gauge - 3371- , observing ⇒ Rep.

    gr. 00 ; centre gaps while doing so.

  • Tighten bolts -1- and -2-.
  • ⇒ Rep. gr. 57 ; Adjusting striker pin
Volkswagen ID.4. Adjusting flushness

Tightening torques

  • ⇒ Rep. gr. 57 ; Assembly overview - door

Adjusting door, right-hand drive vehicles

Special tools and workshop equipment required

  • door alignment tool - 3320-
  • setting gauge - 3371-

Preparation

Important

  • The vehicle must be standing on its wheels and on a level surface to ensure proper adjustment of the door.
  • The door must engage in the striker pin without excessive force.

The door is correctly adjusted when the following applies in closed condition:

  • The gaps are even.
  • The contours are flush with each other.
  • The door does not protrude too far inwards or outwards.

Adjusting shut lines

Left side of vehicle

  • Release and lower fuse holder C - SC- ⇒ Electrical system; Rep. gr. 97 ; Relay carriers, fuse holders, electronics boxes; Removing and installing fuse holder C [CS] .

All vehicles (continued)

Right-hand side of vehicle

  • Remove dash panel cover on driver side ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing dash panel cover on driver side; Removing and installing dash panel cover on driver side .

All vehicles (continued)

  • Remove lower A-pillar trim ⇒ General body repairs, interior; Rep. gr. 70 ; Trims, interior; Removing and installing lower A-pillar trim .
  • Loosen bolts -1-, -2-, -3- and -4-.
  • Check gaps with setting gauge - 3371- , observing ⇒ Rep. gr. 00 ; centre gaps while doing so.
  • Tighten bolts -1-, -2-, -3- and -4-.
Volkswagen ID.4. Adjusting door, right-hand drive vehicles

Adjusting flushness

  • Use door alignment tool - 3320- and corresponding socket to loosen bolts -1- and -2-.
  • Check gaps with setting gauge - 3371- , observing ⇒ Rep. gr. 00 ; centre gaps while doing so.
  • Tighten bolts -1- and -2-.
  • ⇒ Rep. gr. 57 ; Adjusting striker pin
Volkswagen ID.4. Adjusting door, right-hand drive vehicles

Tightening torques

  • ⇒ Rep. gr. 57 ; Assembly overview - door

Adjusting striker pin

Special tools and workshop equipment required

  • setting gauge - 3371-

Important

  • The vehicle must be standing on its wheels and on a level surface to ensure proper adjustment of the striker pin.
  • The door must engage in the striker pin without excessive force.

The striker pin is correctly adjusted when the following applies in closed condition:

  • Gaps are even
  • Contours are flush with each other
  • Door does not protrude too far inwards or outwards
  • Loosen bolts -2-.

Note

Increased forces must be applied so that striker pin can be adjusted with bolts loosened.

  • Push striker pin -1- in direction of -arrow A- or -arrow B- to adjust flushness.
  • Tighten bolts -2-.

Important

  • Tightening sequence must be followed ⇒ Rep. gr. 57 ; Assembly overview - door .
Volkswagen ID.4. Adjusting striker pin
  • Check gaps with setting gauge - 3371- , observing ⇒ Rep. gr. 00 ; centre gaps while doing so.
  • If the door is not adjusted correctly, loosen striker pin and ⇒ Rep. gr. 57 ; adjust door .

Tightening torques

  • ⇒ Rep. gr. 57 ; Assembly overview - door

Removing and installing door hinge

Removing and installing door hinge, left-hand drive vehicles

The upper and lower sections of the door hinge will henceforth be referred to as "door hinge".

Removing

Important

  • Upper and lower part of door hinge must be renewed together.

Preparing

  • Remove door ⇒ Rep. gr. 57 ; Removing and installing door .

Upper section of door hinge

  • Unscrew bolt -1-.
  • Remove door hinge -2-.
Volkswagen ID.4. Upper section of door hinge

Lower section of upper door hinge

Left side of vehicle

  • Release and lower fuse holder C - SC- ⇒ Electrical system; Rep. gr. 97 ; Relay carriers, fuse holders, electronics boxes; Removing and installing fuse holder C [CS] .

All vehicles (continued)

Right-hand side of vehicle

  • Remove glove compartment ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing glove compartment .

All vehicles (continued)

  • Unscrew bolts -1- and -2-.
  • Remove door hinge -3-.
Volkswagen ID.4. Upper section of door hinge

Lower section of lower door hinge

  • Remove lower A-pillar trim ⇒ General body repairs, interior; Rep. gr. 70 ; Trims, interior; Removing and installing lower A-pillar trim .
  • Unscrew bolts -1- and -2-.
  • Remove door hinge -3-.
Volkswagen ID.4. Lower section of lower door hinge

Installing

Install in reverse order of removal, observing the following:

  • ⇒ Rep. gr. 57 ; Adjust door .

Removing and installing door hinge, right-hand drive vehicles

The upper and lower sections of the door hinge will henceforth be referred to as "door hinge".

Removing

Important

  • Upper and lower part of door hinge must be renewed together.

Preparing

  • Remove door ⇒ Rep. gr. 57 ; Removing and installing door .

Upper section of door hinge

  • Unscrew bolt -1-.
  • Remove door hinge -2-.
Volkswagen ID.4. Upper section of door hinge

Lower section of upper door hinge

Left side of vehicle

  • Release and lower fuse holder C - SC- ⇒ Electrical system; Rep. gr. 97 ; Relay carriers, fuse holders, electronics boxes; Removing and installing fuse holder C [CS] .

All vehicles (continued)

Right-hand side of vehicle

  • Remove dash panel cover on driver side ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing dash panel cover on driver side; Removing and installing dash panel cover on driver side .

All vehicles (continued)

  • Unscrew bolts -1- and -2-.
  • Remove door hinge -3-.
Volkswagen ID.4. Lower section of upper door hinge

Lower section of lower door hinge

  • Remove lower A-pillar trim ⇒ General body repairs, interior; Rep. gr. 70 ; Trims, interior; Removing and installing lower A-pillar trim .
  • Unscrew bolts -1- and -2-.
  • Remove door hinge -3-.
Volkswagen ID.4. Lower section of lower door hinge

Installing

Install in reverse order of removal, observing the following:

  • ⇒ Rep. gr. 57 ; Adjust door .

Removing and installing door arrester

Removal and installation are described for the left vehicle side as an example.

Removing

  • Remove assembly carrier ⇒ Rep. gr. 57 ; Removing and installing assembly carrier .

NOTICE

Risk of damage to component surfaces.

  • Mask off A-pillar in area of door arrester using commercially available adhesive tape.
  • Unscrew bolt -2-.
  • Unscrew bolts -3-.
  • Remove door arrester -1- through opening in assembly carrier -arrow-.
Volkswagen ID.4. Removing and installing door arrester

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 57 ; Assembly overview - door