Side airbags
- Assembly overview front side airbag, outer side
- Assembly overview - front side airbag, inner side
- Removing and installing front outer side airbag
- Removing and installing front inner side airbag
Assembly overview front side airbag, outer side
The overview is shown for the left side of vehicle as an example.
- Front side airbag
- With side airbag igniter on driver side - N199- or side airbag igniter on front passenger side - N200-
- ⇒ "8.3 Removing and installing front outer side airbag"
- Bolt
- Renew after removing
- 8 N·m
- Electrical connector
- Front seat frame

Assembly overview - front side airbag, inner side
Overview shows a left-hand drive vehicle as an example
- Central airbag
- With igniter for central airbag for occupant collision protection, driver side - N737-
- Fitted on driver side
- ⇒ Rep. gr. 69 ; Removing and installing front side airbag, inner side
- Clip
- If damaged, central airbag must be renewed.
- Bolt
- Qty. 2
- 8 N·m
- Pop rivet nut
- Qty. 2
- Front seat frame
- Armrest holder
- Bolt
- Renew after removing
- 8 N·m
- Electrical connector

Removing and installing front outer side airbag
Side airbag with side airbag igniter on driver side - N199- or side airbag igniter on front passenger side - N200- are referred to hereafter as "side airbag".
Removal and installation are described for the left side of vehicle as an example.
Removing
- Disconnect battery earth cable ⇒ Electrical system; Rep.
gr. 27 ; Battery; Disconnecting and connecting battery .
- Remove backrest padding in area of side airbag ⇒ Rep.
gr. 74 ; Separating backrest cover from backrest padding .
CAUTION
It is possible to trigger pyrotechnic components unintentionally.
Risk of injury
- Discharge static electricity by briefly touching door striker plate.
- Release connector lock -3- in direction of -arrow-.
- Disconnect electrical connector -2-.
- Unscrew bolt -1-.
- Detach side airbag -4- from hook -5-, and remove it.

WARNING
Risk of injury due to unintended deployment of the airbag unit.
- Place the airbag unit with the airbag facing upwards.
- Place side airbag aside.
Installing
Install in reverse order of removal, observing the following:
CAUTION
It is possible to trigger pyrotechnic components unintentionally.
Risk of injury
- Discharge static electricity by briefly touching door striker plate.
- Connect electrical connector -1- in direction of -arrow A- until it engages audibly.
- Engage connector lock -2- in direction of -arrow B-.
- Make sure that electrical wire is not trapped.

- Connect battery earth cable ⇒ Electrical system; Rep.
gr. 27 ; Battery; Disconnecting and connecting battery .
CAUTION
It is possible to trigger pyrotechnic components unintentionally.
Risk of injury.
- Stay as far back as possible from pyrotechnic components when switching on the ignition
- Switch on ignition.
- Read and clear event memory using ⇒ Vehicle diagnostic tester.
Tightening torques
- ⇒ "8.1 Assembly overview front side airbag, outer side",
Removing and installing front inner side airbag
Special tools and workshop equipment required
- release tool - T10236-
Removing
Side airbag with igniter for central airbag for occupant collision protection, driver side - N737- will henceforth be referred to as "side airbag".
- Disconnect battery earth cable ⇒ Electrical system; Rep.
gr. 27 ; Battery; Disconnecting and connecting battery .
- Remove cover and padding in area of backrest ⇒ Rep.
gr. 74 ; Removing and installing backrest cover and padding .
CAUTION
It is possible to trigger pyrotechnic components unintentionally.
Risk of injury
- Discharge static electricity by briefly touching door striker plate.
- Release connector lock -2- in direction of -arrow-.
- Disconnect electrical connector -3-.
- Unscrew bolts -5-.
Important
- Removed bolts -5- must be coated with locking fluid. Locking fluid ⇒ Electronic parts catalogue (ETKA) .
- Remove clip -4- using release tool - T10236- .
- Unscrew bolt -8-.
- Guide side airbag -1- out of armrest holder -7-, and remove it.

WARNING
Risk of injury due to unintended deployment of the airbag unit.
- Place the airbag unit with the airbag facing upwards.
- Place side airbag aside
Installing
Install in reverse order of removal, observing the following:
CAUTION
It is possible to trigger pyrotechnic components unintentionally.
Risk of injury
- Discharge static electricity by briefly touching door striker plate.
- Connect electrical connector -1- in direction of -arrow A- until it engages audibly.
- Engage connector lock -2- in direction of -arrow B-.
- Make sure that electrical wire is not trapped.

- Connect battery earth cable ⇒ Electrical system; Rep.
gr. 27 ; Battery; Disconnecting and connecting battery .
CAUTION
It is possible to trigger pyrotechnic components unintentionally.
Risk of injury.
- Stay as far back as possible from pyrotechnic components when switching on the ignition.
- Switch on ignition.
- Read and clear event memory using ⇒ Vehicle diagnostic tester.