Power and control electronics for electric drive

In this manual: Power and control electronics for electric drive
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
~9min read
  • Assembly overview - power and control electronics for electric drive, front
  • Removing and installing power and control electronics for electric drive, front

Assembly overview - power and control electronics for electric drive, front

Assembly overview - power and control electronics for electric drive, front

  • Rep. gr. 93 ; Assembly overview - electric drive motor, front

Removing and installing power and control electronics for electric drive at rear

Special tools and workshop equipment required

  • Cleaning solution - D 291 091 A1-
  • anti-twist protection - T10614-
  • brass brush - VAS 294 025-
  • cover - T10643/1- ♦ cover - T10643/2- ♦ puller - T10611- ♦ scraper - VAS 294 027-

The power and control electronics for electric drive - JX1- will henceforth be referred to as "power electronics".

Three-phase current drive - VX54- will henceforth be referred to as "three-phase current drive".

Removing

  • ⇒ Rep. gr. 10 ; Removing motor .
  • ⇒ Rep. gr. 10 ; Secure motor to engine and gearbox support, rear motor .
  • Remove clamping washers -arrows- and take off noise insulation -1-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Unscrew centre hex studs -1- and bolts -arrows-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Lever off cover -1- at positions indicated by -arrows-.

Important

  • The sealing surfaces of the three-phase current drive must not be damaged.

Note

Due to the adhesive strength of the sealant, the cover is bent when being removed. For this reason, the cover needs to be renewed

Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear

Prepare anti-twist protection - T10614- for loosening bus bar bolts:

  • Loosen bolts -C- for retaining plates -B- 1 turn.

Important

  • It must be possible to move the retaining plates -B-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Secure anti-twist protection -A- hand-tight to three-phase current drive using bolts of cover -arrows-, as shown in illustration.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • To loosen bus bar bolts, push retaining plates -B- towards right, and screw in bolts -C- hand-tight.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Unscrew bolts -arrows- for bus bars -1-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Unscrew bolts -arrows-, and remove anti-twist protection -A-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Unscrew bolts -2- for power and control electronics -1- 5 mm -a-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Fit puller - T10611- -D- onto power and control electronics -1-, as shown in illustration.
  • Screw in bolts -E- hand-tight against bolt heads -2-
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear

Important

  • The aid of an additional person is required for the subsequent work steps.

NOTICE

Risk of damage to electrical connector.

  • Before pulling off the power and control electronics, have a second person release and hold the connector lock -arrow-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Release connector lock -arrow-, and hold it in place.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • With connector lock released -arrow-, screw in bolts -Eevenly, and pull off power and control electronics until contact is made with bolt heads -2-.
  • Insert a plastic wedge between the power electronics and three-phase current drive to prevent the electrical connector from re-engaging.
  • Remove puller -D-.
  • Completely unscrew bolts, and detach power and control electronics.

Installing

  • Seal openings on three-phase current drive -1- with cover - T10643/2- -A- and cover - T10643/1- -B-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear

Clean sealing surfaces:

CAUTION

Risk of injury from chemical cleaning agents. Chemical cleaning agents can be highly flammable and can cause eye and skin irritation.

  • Wear safety goggles, safety gloves and a respirator mask.
  • Observe safety data sheet and instructions for use of the cleaning agent.
  • Remove sealant using commercially available chemical sealant remover and scraper - VAS 294 027- .
  • Remove sealant residue using brass brush - VAS 294 025- .
  • Thoroughly clean opening for connecting piece on threephase current drive -arrow-.
  • Coat new connecting piece -2- with lithium grease, and fit it into power and control electronics -1-.

Lithium grease ⇒ Electronic parts catalogue (ETKA)

Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Detach cover - T10643/2- -A- and cover - T10643/1- -B-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Clean sealing surfaces on three-phase current drive -arrowand power and control electronics for electric drive using cleaning solution "D 291 091 A1".
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear

Note

The cleaning solution "D 291 091 A1" is used to activate the surface before the sealant is applied and is essential for the proper functionality of the sealing bond.

Important

  • Allow flash-off time of 10 minutes for sealing surfaces.

Apply sealant for three-phase current drive: Sealant ⇒ Electronic parts catalogue (ETKA)

  • Cut off nozzle on tube at front marking so that nozzle is 3 mm in diameter.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Apply sealant -arrow- onto clean sealing surface of threephase current drive, as shown in illustration.

Important

  • Thickness of sealant bead: 2 to 3 mm.
  • Install power electronics, and tighten bolts within 5 minutes after the sealant has been applied.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Position power electronics -1- on three-phase current drive.
  • Take note of electrical connector when doing this.
  • Screw in bolts -arrows- evenly and in diagonal sequence hand-tight.
  • Tighten bolts -arrows-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear

Prepare anti-twist protection - T10614- for tightening bus bar bolts:

  • Loosen bolts -C- for retaining plates -B- 1 turn.

Important

  • It must be possible to move the retaining plates -B-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Secure anti-twist protection -A- hand-tight to three-phase current drive using bolts of cover -arrows-, as shown in illustration.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • To tighten bus bar bolts, push retaining plates -B- towards left, and screw in bolts -C- hand-tight.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Tighten bolts -arrows- for bus bars -1-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Unscrew bolts -arrows-, and remove anti-twist protection -A-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear

Install cover:

  • Clean sealing surfaces on three-phase current drive -arrowand cover using cleaning solution "D 291 091 A1".

Note

The cleaning solution "D 291 091 A1" is used to activate the surface before the sealant is applied and is essential for the proper functionality of the sealing bond.

Important

  • Allow flash-off time of 10 minutes for sealing surfaces.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Apply sealant -arrow- onto clean sealing surface of threephase current drive, as shown in illustration.

Sealant ⇒ Electronic parts catalogue (ETKA)

Important

  • Thickness of sealant bead: 2 to 3 mm.
  • Install cover and tighten bolts within 5 minutes after the sealant has been applied.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Start centre hex studs -1- and bolts -arrows-, and tighten them. Tightening sequence ⇒ Rep. gr. 93 ; Assembly overview - power and control electronics for electric drive [JX1]
Volkswagen ID.4. Removing and installing power and control electronics for electric drive at rear
  • Carry out leakage test ⇒ Rep. gr. 93 ; Leakage test of electric drive motor, rear .

Continue installing in reverse sequence of removal, observing the following:

If the power and control electronics for electric drive - JX1- has been renewed:

  • Carry out required function/functions using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

Continued

Tightening torques

  • ⇒ Rep. gr. 93 ; Assembly overview - power and control electronics for electric drive, rear
  • ⇒ Rep. gr. 93 ; Assembly overview - electric drive motor, rear

Removing and installing power and control electronics for electric drive, front

Special tools and workshop equipment required

  • brass brush - VAS 294 025-
  • scraper - VAS 294 027-

Power and control electronics 2 for electric drive - JX4- will henceforth be referred to as "power electronics".

Three-phase current drive 2 - VX97- will henceforth be referred to as "three-phase current drive".

Removing

  • ⇒ Rep. gr. 10 ; Remove front motor .
  • ⇒ Rep. gr. 10 ; Secure motor to engine and gearbox support .
  • Unscrew bolts -arrows-, and detach cover -1-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive, front
  • Unscrew bus bar bolts -1-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive, front
  • Unscrew bolts -arrows- for power electronics -1-.
  • Detach power electronics -1- from three-phase current drive.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive, front

Installing

Power electronics sealed with gasket:

  • Renew gasket -1-.
  • Renew dowel pins -2-.
  • Detach coolant connecting piece -3- from three-phase current drive.
  • Thoroughly clean opening for coolant connecting piece on three-phase current drive and on power electronics.
  • Coat new coolant connecting piece -3- with lithium grease, and insert it into three-phase current drive.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive, front

Lithium grease ⇒ Electronic parts catalogue (ETKA)

All vehicles (continued) Power electronics sealed with liquid gasket:

Clean sealing surfaces:

  • Seal openings on three-phase current drive and power electronics.

CAUTION

Risk of injury from chemical cleaning agents. Chemical cleaning agents can be highly flammable and can cause eye and skin irritation.

  • Wear safety goggles, safety gloves and a respirator mask.
  • Observe safety data sheet and instructions for use of the cleaning agent.
  • Remove sealant using commercially available chemical sealant remover and scraper - VAS 294 027- .
  • Remove sealant residue using brass brush - VAS 294 025- .
  • Renew dowel pins -1-.
  • Detach coolant connecting piece -2- from three-phase current drive.
  • Thoroughly clean opening for coolant connecting piece on three-phase current drive and on power electronics.
  • Coat new coolant connecting piece -3- with lithium grease, and insert it into three-phase current drive.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive, front

Lithium grease ⇒ Electronic parts catalogue (ETKA)

  • Clean sealing surfaces on three-phase current drive and power electronics using cleaning solution "D 291 091 A1".

Note

The cleaning solution "D 291 091 A1" is used to activate the surface before the sealant is applied and is essential for the proper functionality of the sealing bond.

Important

  • Allow flash-off time of 10 minutes for sealing surfaces.

Apply sealant for three-phase current drive: Sealant ⇒ Electronic parts catalogue (ETKA)

  • Cut off nozzle on tube at front marking so that nozzle is 3 mm in diameter.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive, front
  • Apply sealant -1- onto clean sealing surface -arrow- of threephase current drive as shown in illustration.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive, front

Important

  • Width of sealant bead: 3 mm.
  • Install power electronics, and tighten bolts within 5 minutes after the sealant has been applied.

All vehicles (continued)

  • Position power electronics -1- on three-phase current drive.

    When doing this, note the dowel pins and coolant connecting piece -arrows-.

Volkswagen ID.4. Removing and installing power and control electronics for electric drive, front
  • Screw in bolts -arrows- evenly and in diagonal sequence hand-tight.
  • Tighten bolts -arrows- to specified tightening torque.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive, front
  • Tighten bus bar bolts -1-.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive, front
  • Fit new cover -1-, and tighten bolts -arrows- evenly and in diagonal sequence.
Volkswagen ID.4. Removing and installing power and control electronics for electric drive, front

Continue installing in reverse sequence of removal, observing the following:

If power and control electronics 2 for electric drive - JX4- has been renewed:

  • Carry out required function/functions using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses

Continued

Tightening torques

  • ⇒ Rep. gr. 93 ; Assembly overview - power and control electronics for electric drive, front ⇒ Rep. gr. 93 ; Assembly overview - electric drive motor, front

Assembly overview - power and control electronics for electric drive, rear

  • ⇒ Rep. gr. 93 ; Assembly overview - electric drive motor, rear .