Connecting brake lines to hydraulic unit
In this manual: Connecting brake lines to hydraulic unit
6steps
~36min
2/5difficulty
Done 0 of 6
- Connecting brake lines to hydraulic unit, left-hand drive vehicles
- Connecting brake lines to hydraulic unit, right-hand drive vehicles
Connecting brake lines to hydraulic unit, left-hand drive vehicles
To hydraulic unit:
- Hydraulic unit to rear right wheel brake cylinder
- 5.25 mm in diameter and union screw with short M12 × 1 thread
- Specified torque ⇒ Rep. gr. 45; Assembly overview - control unit and hydraulic unit
- From hydraulic unit to front left brake caliper
- 5.25 mm in diameter and union screw with M10 × 1 thread
- Specified torque ⇒ Rep. gr. 45; Assembly overview - control unit and hydraulic unit
- From hydraulic unit to front right brake caliper.
- 5.25 mm in diameter and union screw with short M12 × 1 thread
- Specified torque ⇒ Rep. gr. 45; Assembly overview - control unit and hydraulic unit

- Hydraulic unit to rear left wheel brake cylinder
- 5.25 mm in diameter and union screw with M10 × 1 thread
- Specified torque ⇒ Rep. gr. 45; Assembly overview - control unit and hydraulic unit
- From hydraulic unit to secondary piston circuit of brake master cylinder.
- 6 mm in diameter and union screw with M12 × 1 thread
- Specified torque ⇒ Rep. gr. 45; Assembly overview - control unit and hydraulic unit
- From hydraulic unit to primary piston circuit of brake master cylinder.
- 6 mm in diameter and union screw with M12 × 1 thread
- Specified torque ⇒ Rep. gr. 45; Assembly overview - control unit and hydraulic unit
On brake master cylinder:
- Brake servo and brake master cylinder
- Secondary piston circuit of brake master cylinder to hydraulic unit
- Specified torque⇒ Rep.
gr. 47; Assembly overview - brake servo/ brake master cylinder

- Primary piston circuit of brake master cylinder to hydraulic unit
- Specified torque⇒ Rep.
gr. 47; Assembly overview - brake servo/ brake master cylinder
Connecting brake lines to hydraulic unit, right-hand drive vehicles
To hydraulic unit:
- Hydraulic unit to rear right wheel brake cylinder
- 5.25 mm in diameter and union screw with short M12 × 1 thread
- Specified torque ⇒ Rep. gr. 45; Assembly overview - control unit and hydraulic unit
- From hydraulic unit to front left brake caliper
- 5.25 mm in diameter and union screw with M10 × 1 thread
- Specified torque ⇒ Rep. gr. 45; Assembly overview - control unit and hydraulic unit

- From hydraulic unit to front right brake caliper.
- 5.25 mm in diameter and union screw with short M12 × 1 thread
- Specified torque ⇒ Rep. gr. 45; Assembly overview - control unit and hydraulic unit
- Hydraulic unit to rear left wheel brake cylinder
- 5.25 mm in diameter and union screw with M10 × 1 thread
- Specified torque ⇒ Rep. gr. 45; Assembly overview - control unit and hydraulic unit
- From hydraulic unit to secondary piston circuit of brake master cylinder.
- 6 mm in diameter and union screw with M12 × 1 thread
- Specified torque ⇒ Rep. gr. 45; Assembly overview - control unit and hydraulic unit
- From hydraulic unit to primary piston circuit of brake master cylinder.
- 6 mm in diameter and union screw with M12 × 1 thread
- Specified torque ⇒ Rep. gr. 45; Assembly overview - control unit and hydraulic unit
- Clip
- Hydraulic unit
On brake master cylinder:

- Brake servo and brake master cylinder
- Secondary piston circuit of brake master cylinder to hydraulic unit
- Specified torque⇒ Rep.
gr. 47; Assembly overview - brake servo/ brake master cylinder
- Primary piston circuit of brake master cylinder to hydraulic unit
- Specified torque⇒ Rep.
gr. 47; Assembly overview - brake servo/ brake master cylinder
Was this page helpful?