Bonnet

In this manual: Bonnet
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
10steps
~60min
3/5difficulty
0102030405097N·mlb·ft
Tightening torque found on this page
Done 0 of 10
  • Assembly overview - bonnet
  • Assembly overview - Bowden cable
  • Removing and installing bonnet
  • Adjusting hinges
  • Adjusting striker pin
  • Adjusting bonnet lock
  • Removing and installing striker pin
  • Removing and installing Bowden cable
  • Removing and installing bonnet stay

Assembly overview - bonnet

  1. Bonnet
  • ⇒ Rep. gr. 55 ; Removing and installing bonnet
  • ⇒ Rep. gr. 55 ; Adjusting bonnet
  1. Striker pin
  • ⇒ Rep. gr. 55 ; Removing and installing striker pin
  • ⇒ Rep. gr. 55 ; Adjusting striker pin
  1. Nut
  • Qty. 2
  • 9 N·m
  1. Adjusting buffer
  • Qty. 4
  • ⇒ Rep. gr. 55 ; Setting adjusting buffer
  1. Hinge
  • ⇒ Rep. gr. 55 ; Removing and installing hinge
  • ⇒ Rep. gr. 55 ; Adjusting hinges
  1. Nut
  • Qty. 4
  • 20 N·m
  1. Bolt
  • Qty. 4
  • 20 N·m
  1. Bonnet stay
  • ⇒ Rep. gr. 55 ; Removing and installing bonnet stay
  1. Bonnet lock
  • With bonnet contact switch - F266-
  • ⇒ Rep. gr. 55 ; Removing and installing bonnet
  • ⇒ Rep. gr. 55 ; Adjusting bonnet
  1. Bolt
  • Qty. 2
  • Renew after removing
  • 12 N·m
  1. Rubber grommet for bonnet stay
  2. Retainer for bonnet stay
  3. Bolt
  • Qty. 2
  • 8 N·m
  1. Bolt
  • Qty. 2
  • 2 N·m
Volkswagen ID.4. Assembly overview - bonnet
  1. Bonnet mounting
  • Qty. 2
  1. Bolt
  • Qty. 2
  • 4,5 N·m

Assembly overview - Bowden cable

Overview shows a left-hand drive vehicle as an example

  1. Bonnet lock operating lever
  • ⇒ Rep. gr. 55 ; Removing and installing bonnet lock operating lever
  1. Bolt
  • 2 N·m
  1. Mounting bracket
  2. Expansion nut
  3. Bowden cable
  • From mounting bracket -3- to Bowden cable coupling -7-
  • ⇒ Rep. gr. 55 ; Removing and installing Bowden cable
  1. Grommet
  2. Bowden cable coupling
  3. Electrical connector for bonnet contact switch - F266-
  4. Bowden cable
  • From Bowden cable coupling -7- to bonnet lock -10-.
  • ⇒ Rep. gr. 55 ; Removing and installing Bowden cable
  1. Bonnet lock
  • With bonnet contact switch - F266-
  • ⇒ Rep. gr. 55 ; Removing and installing bonnet lock
  1. Bolt
  • Qty. 2
  • 12 N·m
Volkswagen ID.4. Assembly overview - Bowden cable

Removing and installing bonnet

Removing

  • Remove spray jets -5- ⇒ Electrical system; Rep. gr. 92 ; Window washer system; Removing and installing spray jets .
  • Pull out washer fluid hose and electrical wires -4-.
  • Loosen nuts -2- of hinges -3-.

Important

  • A second person is required for the following steps.
  • Unhook bonnet stay -6- from bonnet -1-.
  • Unscrew nuts -2-.
  • Remove bonnet -1-.
Volkswagen ID.4. Removing and installing bonnet

Installing

Install in reverse order of removal, observing the following:

NOTICE

Risk of damage to electrical wire if not installed straight.

  • Do not kink electrical wire and route in a curve.
  • Install washer fluid hose and electrical wires.
  • ⇒ Rep. gr. 55 ; Adjust bonnet .

Tightening torques

  • ⇒ Rep. gr. 55 ; Assembly overview - bonnet

Adjusting bonnet

Special tools and workshop equipment required

  • setting gauge - 3371-

Important

  • The vehicle must be standing on its wheels and on a level surface to ensure proper adjustment of the bonnet.
  • Bonnet must engage in bonnet lock without excessive force.
  • Striker pin must enter bonnet lock in centre.

The bonnet is correctly adjusted when the following applies in closed condition:

  • Gaps are even
  • Contours are flush with each other
  • Bonnet does not protrude too far inwards or outwards
  • Adjust adjusting buffers ⇒ Rep. gr. 55 ; Adjusting adjusting buffers .
  • Adjust hinges ⇒ Rep. gr. 55 ; Adjusting hinges .
  • Adjust bonnet lock ⇒ Rep. gr. 55 ; Adjusting bonnet lock .
  • Adjust striker pin ⇒ Rep. gr. 55 ; Adjusting striker pin
  • Check gaps with setting gauge - 3371- , observing ⇒ Rep. gr. 00 ; front gaps while doing so.

Adjusting hinges

Special tools and workshop equipment required

  • setting gauge - 3371-

The procedure is described for the left side of vehicle as an example.

Note

The bonnet can be centred between the wings in direction of -arrow C- and in direction of -arrow D-.

  • Loosen nuts -2- to adjust hinge -1- in direction of -arrow Cor in direction of -arrow D-.

Note

The height of the bonnet relative to the wings can be adjusted in direction of -arrow B-.

Note

The bonnet can be adjusted relative to the bumper cover in direction of -arrow A-.

  • Loosen bolts -3- to adjust hinge -1- in direction of -arrow Aor in direction of -arrow B-.
  • Verify gaps using setting gauge - 3371- . Observe ⇒ Rep. gr. 00 ; Gaps - front when doing this.
  • Apply corrosion protection measures to hinges -1-, nuts -2- and bolts -3- ⇒ Corrosion protection on body, attachments and welded parts .
Volkswagen ID.4. Adjusting hinges
  • ⇒ Rep. gr. 55 ; Adjust adjusting buffers .

Tightening torques

  • ⇒ Rep. gr. 55 ; Assembly overview - bonnet

Adjusting striker pin

  • Adjust striker pin in direction of -arrow A- to align it centrally relative to bonnet lock.
  • Loosen nuts -2- to adjust striker pin -1- in direction of -arrow A-.

Important

  • Do not use striker pin to align bonnet centrally in direction of -arrow A-.
  • Striker pin must enter bonnet lock in centre
Volkswagen ID.4. Adjusting striker pin

Tightening torques

  • ⇒ Rep. gr. 55 ; Assembly overview - bonnet

Setting adjusting buffers

Adjusting buffers stabilise the bonnet and provide shock absorption.

  • Adjust bonnet lock ⇒ Rep. gr. 55 ; Removing and installing bonnet lock .
  • Adjust striker pin ⇒ Rep. gr. 55 ; Adjusting striker pin .

Note

Adjusting buffers offer stability and protect against impact. Applying too much pressure on the rubber buffer will result in a malfunction.

  • Turn adjusting buffer -1- in direction of -arrow A- or -arrow B-.

Important

  • When bonnet is closed, adjusting buffers -1- must have light contact with stop buffers.
Volkswagen ID.4. Setting adjusting buffers

Adjusting bonnet lock

Special tools and workshop equipment required

  • setting gauge - 3371-

Important

  • Do not use bonnet lock to align bonnet centrally in direction of -arrow A-.
  • Striker pin must enter bonnet lock in centre. ⇒ Rep. gr. 55 ; Adjusting striker pin

Note

The bonnet can be adjusted relative to the front bumper cover in direction of -arrow B-.

  • Loosen bolts -2- to adjust bonnet lock -1- in direction of -arrow A- or direction of -arrow B-.
  • Verify gaps using setting gauge - 3371- . Observe ⇒ Rep. gr. 00 ; Gaps - front when doing this.
  • Apply corrosion protection measures to bolts -2- ⇒ Corrosion protection on body, attachments and welded parts .
Volkswagen ID.4. Adjusting bonnet lock

Tightening torques

  • ⇒ Rep. gr. 55 ; Assembly overview - bonnet

Removing and installing bonnet lock

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

  • Remove lock carrier ⇒ Rep. gr. 50 ; Removing and installing lock carrier .
  • Unclip Bowden cable -2- and electrical wire -5- from retainers -7-.
  • Unscrew bolts -3-.
  • Remove bonnet lock -1- in direction of -arrow A- from lock carrier -6-.
  • Unclip electrical wire -5- from bonnet lock.
  • Slightly pull retainer -4- in direction of -arrow B- off bonnet lock -1-, and detach Bowden cable -2- in direction of -arrow C-.
Volkswagen ID.4. Removing and installing bonnet lock

Installing

Install in reverse order of removal, observing the following:

Tightening torques

  • ⇒ Rep. gr. 55 ; Assembly overview - Bowden cable

Removing and installing striker pin

Removing

  • Unscrew nuts -2-.
  • Remove striker pin -1- from bonnet.
Volkswagen ID.4. Removing and installing striker pin

Installing

Install in reverse order of removal, observing the following:

  • ⇒ Rep. gr. 55 ; Adjust striker pin .

Tightening torques

  • ⇒ Rep. gr. 55 ; Assembly overview - bonnet

Removing and installing bonnet lock operating lever

Bonnet lock operating lever is referred to hereafter as operating lever.

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

  • Pull operating lever -1-, and hold it in this position.
  • Using commercially available screwdriver, pull retaining clip -2- in direction of -arrow A- out of operating lever -1-.
  • Detach operating lever -1- from mounting bracket -3- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing bonnet lock operating lever

Installing

Install in reverse order.

Removing and installing hinge

Removal and installation are described for the right vehicle side as an example.

Removing

  • Remove bonnet ⇒ Rep. gr. 55 ; Removing and installing bonnet .
  • Unscrew bolts -2-.
  • Pull off hinge -1-.
Volkswagen ID.4. Removing and installing hinge

Installing

Install in reverse order of removal, observing the following:

  • Apply corrosion protection measures to bolts.

Observe instructions in the paintwork manual ⇒ Corrosion protection on body, attachments and welded parts .

  • ⇒ Rep. gr. 55 ; Adjust bonnet .

Tightening torques

  • ⇒ Rep. gr. 55 ; Assembly overview - bonnet

Removing and installing Bowden cable

Removal and installation are described for a left-hand drive vehicle as an example.

Removing

  • Remove lower A-pillar trim ⇒ General body repairs, interior; Rep. gr. 70 ; Trims, interior; Removing and installing lower A-pillar trim .
  • Remove footwell cover on driver side ⇒ General body repairs, interior; Rep. gr. 68 ; Compartments/covers; Removing and installing footwell cover on driver side .
  • Remove front wheel housing liner on driver side ⇒ Rep. gr. 66 ; Removing and installing front wheel housing liner .
  • Remove wiper motor - V- ⇒ Electrical system; Rep. gr. 92 ; Windscreen wiper system; Removing and installing wiper motor [V] .
  • Detach Bowden cable -1- in direction of -arrow A- from mounting bracket -2-.
Volkswagen ID.4. Removing and installing Bowden cable
  • Pull Bowden cable coupling -1- in direction of -arrow A- off carrier -3-.
  • Pretension Bowden cable -2- in direction of -arrow B-, and hold it in this position.
Volkswagen ID.4. Removing and installing Bowden cable
  • Open cap -1- of Bowden cable coupling -2- in direction of -arrow A-.
  • Remove Bowden cable -3- in direction of -arrow B- from Bowden cable coupling -2-.
Volkswagen ID.4. Removing and installing Bowden cable
  • Pull Bowden cable -1- together with grommet -2- in direction of -arrow A- off body, and remove it.
Volkswagen ID.4. Removing and installing Bowden cable

Installing

  • Guide Bowden cable -1- with grommet -2- in direction of -arrow A- through opening in body -3- towards vehicle interior.
  • Push grommet -2- into opening in body -3-.
  • Make sure that grommet -2- is seated correctly.
Volkswagen ID.4. Removing and installing Bowden cable

NOTICE

Risk of malfunction of the bonnet lock due to incorrect position of the Bowden cable in the Bowden cable coupling.

If the Bowden cable is installed in the wrong position, the bonnet can no longer be opened.

  • Make sure that the Bowden cable is correctly positioned in the Bowden cable coupling.
  • Always carry out a functional check before closing the bonnet.
  • Attach Bowden cable -1- in direction of -arrow A- to Bowden cable coupling -2-.
  • Use cap -3- of Bowden cable coupling -2- to fix Bowden cable -1- in position, but do not close cap -3-.
  • Pretension Bowden cable -1- in direction of -arrow B-, and hold it in this position.
  • Close cap -3- in direction of -arrow C-.
Volkswagen ID.4. Removing and installing Bowden cable
  • Relieve tension from Bowden cable -1- in direction of -arrow A-.
  • Secure Bowden cable coupling -3- in direction of -arrow Bon carrier -2-.
Volkswagen ID.4. Removing and installing Bowden cable
  • Attach Bowden cable -1- in direction of -arrow A- to mounting bracket -2-.
Volkswagen ID.4. Removing and installing Bowden cable

Further installation is carried out in reverse order of removal.

Observe the following when doing this:

  • Perform functional check.
  • Close bonnet.

Removing and installing bonnet stay

Special tools and workshop equipment required

  • bonnet support - VAS 501 003-

Removal and installation are described for vehicles with bonnet stay on right as an example.

Bonnet stay mounting design is model-specific.

Removing

NOTICE

Risk of damage to adjacent components caused by a loose bonnet.

Risk of paint damage.

  • Brace the bonnet open.
  • Support bonnet using bonnet support - VAS 501 003- .
  • Pull bonnet stay -1- out of clip -2-.
  • Swivel bonnet stay -1- out of mounting on lock carrier.
  • Remove bonnet stay -1- in direction of -arrow B-.
Volkswagen ID.4. Removing and installing bonnet stay

Installing

Install in reverse order.