Front brake

In this manual: Front brake
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
8steps
~48min
2/5difficulty
060120180240300200148N·mlb·ft
Tightening torque found on this page
Done 0 of 8
  • Assembly overview - front brake
  • Removing and installing brake pads
  • Removing and installing brake caliper
  • Removing and installing brake disc

Assembly overview - front brake

The overview is shown for the left side of the vehicle as an example.

  1. Ribbed bolt
  • Qty. 2
  • 200 N·m
  1. Wheel bearing housing
  • ⇒ Running gear, axles, steering; Rep. gr. 42; Wheel bearing, trailing arm; Assembly overview - wheel bearing
Volkswagen ID.4. Assembly overview - front brake
  1. Brake pads
  • Depending on equipment/ installation period, with front right brake pad wear sender -G35-
  • Check thickness of brake linings ⇒ Maintenance; Booklet ; Front and rear brake pads/ linings: Checking thickness
  • Wear limits ⇒ Rep.

    gr. 00; Test and adjustment values

  • ⇒ Rep. gr. 46; Removing and installing brake pads
  1. Bolt
  • Qty. 2
  • Renew after removing
  • 65 N·m
  1. Brake caliper
  • Depending on equipment/ installation period, single or dual piston brake
  • ⇒ Rep. gr. 46; Removing and installing brake caliper
  1. Bleeder valve
  • 11 N·m
  1. Dust cap
  2. Line for front brake pad wear sender
  3. Brake carrier
  4. Pad retainer
  • Renew after removing
  1. Brake disc
  • Wear limits ⇒ Rep. gr. 00; Test and adjustment values
  • ⇒ Rep. gr. 46; Removing and installing brake disc
  1. Torx bolt
  • 8 N·m
  1. Torx bolt
  • Qty. 3
  • 12 N·m
  1. Cover plate
  2. Brake hose with banjo union and banjo bolt
  • Banjo bolt on brake caliper: 38 N·m
  1. Retaining clip
  2. Brake line
  • 14 N·m
  1. Bolt
  • 8 N·m
  1. Bracket

Removing and installing brake pads

Special tools and workshop equipment required

  • Piston resetting appliance -T10145-
  • hook -VAS 281 007-

WARNING

Health hazard due to poisonous dust from brake system.

Risk of irreversibly deposited dust particles in the lungs. Risk of respiratory health problems.

  • Do not blow out brake system with compressed air.

NOTICE

Opened brake system.

Damage to brake system.

  • Do not depress brake pedal during the procedure.

Removing

Removal and installation are described for left side of vehicle as an example

  • ⇒ Running gear, axles, steering; Rep. gr. 44; Wheels, tyres; Removing wheel

Right side of vehicle

  • Disconnect electrical connector of front right brake pad wear sender -G35-.

All vehicles (continued)

  • Unscrew bolts -2- from brake carrier -1-. Counterhold on guide pin -3- when doing this.
Volkswagen ID.4. All vehicles (continued)
  • Remove brake caliper -1-.
Volkswagen ID.4. All vehicles (continued)
  • Secure brake caliper -1- with hook -VAS 281 007- to prevent it from falling down
  • Use a screwdriver -A- to lever off brake pad retaining springs -arrows-.
Volkswagen ID.4. All vehicles (continued)

Important

  • Do not bend brake pad retaining springs when doing this.
  • Mark used brake pads when removing, and reinstall them in the same position.
Volkswagen ID.4. All vehicles (continued)
  • Turn brake pad -1- in direction of -arrow A-, and remove it in direction of -arrow B-.
  • Use a screwdriver -A- to lever off pad retainers -1- at positions marked with -arrows-.
Volkswagen ID.4. All vehicles (continued)
  • Thoroughly clean contact surfaces of brake pads on brake carrier using suitable workshop means, and remove corrosion.

CAUTION

Risk of injury from chemical cleaning agents. Chemical cleaning agents can be highly flammable and can cause eye and skin irritation.

  • Wear safety goggles, safety gloves and a respirator mask.
  • Observe safety data sheet and instructions for use of the cleaning agent.
  • Clean brake caliper.

Important

  • Use only commercially available methylated spirits for cleaning the brake caliper.

Installing

Important

  • Before pushing the brake piston back into the cylinder using the piston resetting appliance -T10145-, brake fluid must be extracted from the brake fluid reservoir so that no brake fluid that has been refilled in the meantime can drain out.

For a better view, the following work procedure is shown with the brake caliper removed.

  • Press back piston with piston resetting appliance -T10145- -A-.
Volkswagen ID.4. All vehicles (continued)
  • Press pad retainers -arrows- into brake carrier.
Volkswagen ID.4. All vehicles (continued)

For directional brake pads

  • Install directional brake pads marked with "OUTSIDE"-1- on the outer side and those marked with "INSIDE"-2- on the inner side.
Volkswagen ID.4. For directional brake pads

All vehicles (continued)

Important

  • Bake pads must be renewed on both sides of axle.
  • Push brake pad -1- in direction of -arrow A- against resistance of brake pad retaining springs -2- into recess in brake carrier.
Volkswagen ID.4. All vehicles (continued)
  • Simultaneously, push brake pad -1- in direction of -arrow Binto recess in brake carrier and against brake disc (direction of -arrow C-)
  • Press brake pad retaining springs -arrows- onto brake carrier.
Volkswagen ID.4. All vehicles (continued)
  • Make sure that all brake pad retaining springs -arrows- are firmly seated.
  • Place brake caliper onto brake carrier.
  • Secure brake caliper to brake carrier -1- using new self-locking bolts -2- while counterholding on guide pin -3-.
Volkswagen ID.4. All vehicles (continued)

Right side of vehicle

  • Connect electrical connector of front right brake pad wear sender -G35-.

All vehicles (continued)

  • ⇒ Running gear, axles, steering; Rep. gr. 44; Wheels, tyres; Installing wheel.
  • Firmly depress brake pedal several times with vehicle stationary so that the brake pads/linings are properly seated in their normal operating position.
  • Check brake fluid level.
Volkswagen ID.4. All vehicles (continued)

Important

  • Brake fluid level must be between "MIN." -2- and "MAX." -1-.
  • Ensure that brakes work properly before the vehicle is driven.

Tightening torques

  • ⇒ Rep. gr. 46; Assembly overview - front brake

Removing and installing brake caliper

Special tools and workshop equipment required

  • brake pedal actuator -V.A.G 1869/2-
  • hook -VAS 281 007-

WARNING

Health hazard due to poisonous dust from brake system.

Risk of irreversibly deposited dust particles in the lungs. Risk of respiratory health problems.

  • Do not blow out brake system with compressed air

CAUTION

Brake pads that are reused.

Uneven braking efficiency.

  • Mark brake pads when removing, and reinstall them in the same position.

NOTICE

Opened brake system.

Damage to brake system.

  • Do not depress brake pedal during the procedure.

The work procedure applies only for renewal of the brake caliper.

Removal and installation are described for left side of vehicle as an example.

Removing

  • Remove wheel ⇒ Running gear, axles, steering; Rep. gr. 44; Wheels, tyres; Removing wheel.

Right side of vehicle

  • Disconnect electrical connector of front right brake pad wear sender -G35-.

All vehicles (continued)

  • Connect hose of bleeder bottle -1- to bleeder valve of brake caliper.
Volkswagen ID.4. Removing and installing brake caliper
  • Open bleeder valve.
  • Fit brake pedal actuator -V.A.G 1869/2-.
Volkswagen ID.4. Removing and installing brake caliper
  • Close bleed valve and remove bleed bottle.
  • Unscrew brake hose.
  • Unscrew bolts -2- while counterholding on guide pin -3-.
Volkswagen ID.4. Removing and installing brake caliper
  • Pull brake caliper off brake carrier -1-.
  • Secure brake caliper -1- with hook -VAS 281 007- to prevent it from falling down.

Installing

Important

  • The piston is pressed back.
  • The retaining springs of the brake pads are seated in the recesses in the brake carrier.
  • Place brake caliper onto brake carrier.
  • Secure brake caliper to brake carrier -1- with bolts -2- while counterholding on guide pin -3-.
Volkswagen ID.4. Removing and installing brake caliper
  • Screw brake hose into brake caliper, and tighten it.
  • Remove brake pedal actuator -V.A.G 1869/2-.

Right side of vehicle

  • Connect electrical connector of front right brake pad wear sender -G35-.

All vehicles (continued)

  • ⇒ Rep. gr. 47; Bleed hydraulic system.
  • Install wheel ⇒ Running gear, axles, steering; Rep. gr. 44; Wheels, tyres; Installing wheel.

Firmly depress brake pedal several times with vehicle stationary so that the brake pads/linings are properly seated in their normal operating position.

  • Check brake fluid level.
Volkswagen ID.4. Firmly depress brake pedal several times with vehicle stationary so that the brake pads/linings are properly seated in their normal operating position.

Important

The brake fluid level must be between "Min." -2- and "Max." -1-.

Continued

Tightening torques

  • ⇒ Rep. gr. 46; Assembly overview - front brake

Removing and installing brake disc

Removing

Removal and installation are described for the left side of vehicle as an example.

  • Remove brake pads ⇒ Rep. gr. 46; Removing and installing brake pads.
  • Unscrew bolts -2-, and remove brake carrier -1-.
Volkswagen ID.4. Removing and installing brake disc
  • Unscrew bolt -2-, and hold brake disc -1- when doing this.
Volkswagen ID.4. Removing and installing brake disc
  • Remove brake disc -1-.
  • Thoroughly clean contact surface of brake disc and wheel hub. Remove corrosion with suitable workshop equipment.
  • Clean brake discs.

Important

  • Use only commercially available methylated spirits to clean brake discs.

Installing

Install in reverse order of removal, observing the following:

Important

  • Bake discs must be renewed on both sides of axle.

Tightening torques

  • ⇒ Rep. gr. 46; Assembly overview - front brake