Luggage compartment floor
- Assembly overview - sealing channel support
- Assembly overview - centre luggage compartment floor
- Assembly overview - luggage compartment floor cross member
- Renewing floor panel reinforcement
- Renewing centre luggage compartment floor
- Renewing rear luggage compartment floor
- Renewing luggage compartment floor cross member
Assembly overview - sealing channel support
Overview shown for left side of vehicle as an example
- Support
- Sealing channel
- ⇒ Rep. gr. 53; Renewing sealing channel support
- Bonded areas

Assembly overview - floor panel reinforcement
Overview shown for left side of vehicle as an example
- Floor panel reinforcement
- ⇒ Rep. gr. 53; Renewing floor panel reinforcement
- Bonded areas

Assembly overview - centre luggage compartment floor
- Centre luggage compartment floor
- ⇒ Rep. gr. 53; Renewing centre luggage compartment floor
- Separating cut
- Bonded area
- Separating cut
- Rear floor cross member

Assembly overview - rear luggage compartment floor
- Rear luggage compartment floor
- ⇒ Rep. gr. 53; Renewing rear luggage compartment floor
- Bonded area

Assembly overview - luggage compartment floor cross member
- Luggage compartment floor cross member
- ⇒ Rep. gr. 53; Renewing luggage compartment floor cross member
- Bonded area

Renewing sealing channel support
WARNING
Gases/vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.
- Do not weld, solder or cut closer than 15 mm to moulded foam inserts.
- Use an extraction system during work.
NOTICE
If separating cuts are made too deep, underlying reinforcement could be damaged.
- Only make separating cuts with body saw.
- Rewelding of reinforcements is not permitted due to safety reasons.
Observe safety information ⇒ Rep. gr. 00; Safety information
Only tools and workshop equipment authorised by Volkswagen AG may be used ⇒ 2.1
Removal and installation are described for left side of vehicle as an example.
Removing
- Separate original joint.

- Detach sealing channel support -1-.
- Remove remaining material.

- Completely remove remaining adhesive.
- Grind bonding surfaces and welding surfaces back to bare metal and clean.
Installing
- Drill or alternately punch 8 mm holes for SG plug weld seam in new part -1-.

- Adapt new part -1- to fit and fix in position.

- Check fit with add-on parts.
- Weld in new part -1-, SG plug weld seam.
Renewing floor panel reinforcement
WARNING
Gases/vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.
- Do not weld, solder or cut closer than 15 mm to moulded foam inserts.
- Use an extraction system during work.
NOTICE
If separating cuts are made too deep, underlying reinforcement could be damaged.
- Only make separating cuts with body saw.
- Rewelding of reinforcements is not permitted due to safety reasons.
Observe safety information ⇒ Rep. gr. 00; Safety information Only tools and workshop equipment authorised by Volkswagen AG may be used ⇒ 2.1
Removal and installation are described for left side of vehicle as an example.
Removing
- Separate original joint.

- Remove floor panel reinforcement -1-.
- Remove remaining material.

- Completely remove remaining adhesive.
- Grind bonding surfaces and welding surfaces back to bare metal and clean.
Installing
- Drill 8 mm diameter holes for SG plug weld seam in new part -1-.

- Adapt new part -1- to fit and fix in position.

- Check fit with add-on parts.
- Weld in new part -1-, SG plug weld seam.
Renewing centre luggage compartment floor
WARNING
Gases/vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.
- Do not weld, solder or cut closer than 15 mm to moulded foam inserts.
- Use an extraction system during work.
NOTICE
If separating cuts are made too deep, underlying reinforcement could be damaged.
- Only make separating cuts with body saw.
- Rewelding of reinforcements is not permitted due to safety reasons.
NOTICE
If welds are positioned too far on outside, strength could be impaired
- RP weld points must be placed as far as possible from outer edge of welding flange.
NOTICE
If adhesive is applied prematurely, bond could be impaired
- New part must be welded in within 90 minutes.
Observe safety information ⇒ Rep. gr. 00; Safety information Only tools and workshop equipment authorised by Volkswagen AG may be used ⇒ 2.1
Removing
Rear luggage compartment floor removed ⇒ Rep. gr. 53; Renewing rear luggage compartment floor.
Floor panel reinforcement removed ⇒ Rep. gr. 53; Renewing floor panel reinforcement.
- Make separating cut -2- in a straight line.

- Separate original joint.
- Remove centre luggage compartment floor -1-.
- Remove remaining material.

- Completely remove remaining adhesive.
- Grind bonding surfaces and welding surfaces back to bare metal and clean.
Installing
- For allocation of 2-pack body adhesive, see ⇒ Electronic parts catalogue (ETKA)
Important
- New parts must be adapted and attached with the vehicle standing on its wheels or straightening bracket set.
- Transfer separating cut -2- to new part -1-, and cut in a straight line.

- Drill or alternately punch 8 mm holes for SG plug weld seam in new part -1-.
- Grind welding surfaces and bonding surfaces on new part -1- down to bare metal and clean.
- Apply 2-component body adhesive to entire surface.

- Adapt new part -1- to fit and fix in position.

- Weld in new part -1-, SG plug weld seam and RP spot weld seam.
- Install rear luggage compartment floor ⇒ Rep. gr. 53; Renewing rear luggage compartment floor.
- Install floor panel reinforcement ⇒ Rep. gr. 53; Renewing floor panel reinforcement.
Renewing rear luggage compartment floor
WARNING
Gases/vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.
- Do not weld, solder or cut closer than 15 mm to moulded foam inserts.
- Use an extraction system during work.
NOTICE
If separating cuts are made too deep, underlying reinforcement could be damaged.
- Only make separating cuts with body saw.
- Rewelding of reinforcements is not permitted due to safety reasons.
NOTICE
If welds are positioned too far on outside, strength could be impaired
- RP weld points must be placed as far as possible from outer edge of welding flange.
NOTICE
If adhesive is applied prematurely, bond could be impaired
- New part must be welded in within 90 minutes.
Observe safety information ⇒ Rep. gr. 00; Safety information Only tools and workshop equipment authorised by Volkswagen AG may be used ⇒ 2.1
Removing
Rear cross panel removed ⇒ Rep. gr. 53; Renewing rear cross panel.
- Separate original joint.

- Remove rear floor panel -1-.
- Remove remaining material.

- Completely remove remaining adhesive.
- Grind bonding surfaces and welding surfaces back to bare metal and clean.
Installing
- For allocation of 2-pack body adhesive, see ⇒ Electronic parts catalogue (ETKA)
Important
- New parts must be adapted and attached with the vehicle standing on its wheels or straightening bracket set.
- Grind welding surfaces and bonding surfaces on new part -1- down to bare metal and clean.

- Apply 2-component body adhesive to entire surface.

- Adapt new part -1- to fit and fix in position.

- Weld in new part -1-, RP spot weld seam.
- Install rear cross panel ⇒ Rep. gr. 53; Renewing rear cross panel.
Renewing luggage compartment floor cross member
WARNING
Gases/vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.
- Do not weld, solder or cut closer than 15 mm to moulded foam inserts.
- Use an extraction system during work.
NOTICE
If separating cuts are made too deep, underlying reinforcement could be damaged.
- Only make separating cuts with body saw.
- Rewelding of reinforcements is not permitted due to safety reasons.
NOTICE
If welds are positioned too far on outside, strength could be impaired
- RP weld points must be placed as far as possible from outer edge of welding flange.
NOTICE
If adhesive is applied prematurely, bond could be impaired
- New part must be welded in within 90 minutes.
Observe safety information ⇒ Rep. gr. 00; Safety information Only tools and workshop equipment authorised by Volkswagen AG may be used ⇒ 2.1
Removing
Centre luggage compartment floor part section removed ⇒ Rep.
gr. 53; Renewing centre luggage compartment floor.
- Separate original joint.

- Remove luggage compartment floor cross member -1-.
- Remove remaining material.

- Completely remove remaining adhesive.
- Grind bonding surfaces and welding surfaces back to bare metal and clean.
Installing
- For allocation of 2-pack body adhesive, see ⇒ Electronic parts catalogue (ETKA)
Important
- New parts must be adapted and attached with the vehicle standing on its wheels or straightening bracket set.
- Grind welding surfaces and bonding surfaces on new part -1- down to bare metal and clean.

- Apply 2-component body adhesive to entire surface.

- Adapt new part -1- to fit and fix in position

- Check fit with add-on parts.
- Weld in new part -1-, RP spot weld seam.
- Install centre luggage compartment floor part section ⇒ Rep.
gr. 53; Renewing centre luggage compartment floor.