Rear windscreen

In this manual: Rear windscreen
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
6steps
~36min
2/5difficulty
Done 0 of 6
  • Assembly overview - rear window
  • Removing and installing rear window

Assembly overview - rear window

  1. Rear window - ZX1-
  • With heated rear window - Z1-
  • With glass breakage sensor for rear window - G304- depending on model
  • ⇒ Rep. gr. 64 ; Removing and installing rear window
  • ⇒ General information - body; Rep.gr. 52 ; General notes - windows; Removing broken window
  1. Body flange
  2. Spacer
  • Depending on model
  1. Electrical connector for heated rear window - Z1-
  • Negative wire
  1. Frequency modulation (FM) frequency filter in negative wire - R178-
  2. Electrical connector for glass breakage sensor for rear window - G304-
  • Depending on model
  • Depending on equipment/ installation version
  1. Side spoiler
  • Depending on model
  • ⇒ ; Rep. gr. 66 ; Spoiler; Removing and installing side spoiler
  1. Centring pin
  • Depending on equipment/installation version
  • Qty. 2
  1. Electrical connector for heated rear window - Z1-
  • Positive wire
  1. Frequency modulation (FM) frequency filter in positive wire - R179-
  2. Electrical connector for window aerial
  • Negative wire
  1. Electrical connector for window aerial
  • Positive wire
Volkswagen ID.4. Assembly overview - rear window

Removing and installing rear window

Special tools and workshop equipment required

  • awl - V.A.G 1474/2-
  • cutting cord - VAS 861 001/1A-
  • plastic strip - V.A.G 1474/15-
  • pull handle - V.A.G 1351/1-
  • reel device - V.A.G 1654 A-
  • removal kit for flush bonded windows - V.A.G 1474B-
  • removal kit for flush bonded windows - VAS 6452-
  • setting gauge - 3371-
  • wedge - V.A.G 1474/5-
  • windscreen removal set - VAS 861 001A

Removing

The description for the removal of the rear window is based on the removal kit for flush bonded windows - V.A.G 1474B- .

Alternatively, removal kit for flush bonded windows - VAS 6452- or windscreen removal set - VAS 861 001A- can also be used.

Important

  • When reusing the rear window - ZX1- , make sure not to damage the electrical connectors for the heated rear window - Z1- , the window aerials and the glass breakage sensor for rear window - G304- .
  • Disconnect electrical connectors for heated rear window - Z1- , window aerials and glass breakage sensor for rear window - G304- .

CAUTION

Risk of injury to hands and eyes due to glass splinters.

Danger of cutting yourself.

  • Put on safety goggles.
  • Put on protective gloves.

NOTICE

Risk of damage to surfaces of components.

  • Mask off surrounding components in the visible area with commercially available adhesive tape.
  • Pull cutting cord - VAS 861 001/1A- -1- with awl - V.A.G 1474/2- -4- at marked position -arrow A- towards inside through adhesive sealant.
  • Secure end of cutting cord with pull handle - V.A.G 1351/1- to prevent it from being pulled out.
  • Place cutting cord around rear window -2- and guide 2nd end of cutting cord inwards.
  • Secure end of cutting cord to reel device - V.A.G 1654 A- -3-.
Volkswagen ID.4. Removing and installing rear window
  • Push in plastic strip - V.A.G 1474/15- between rear window and body flange.
  • Fit reel device -3- in position shown, and cut free rear window in upper area towards both sides.
  • Reposition reel device -3- and cut free rear window in lower area.
  • Use wedge - V.A.G 1474/5- -2- to press cutting cord -1- against rear window while cutting it free to ensure sufficient clearance to body flange.
Volkswagen ID.4. Removing and installing rear window

Important

  • The aid of an additional person is required for the subsequent work steps.
  • Use 2 suction lifters to remove rear window.

Installing

Install in reverse order of removal, observing the following:

Undamaged windscreen

  • ⇒ General information - body; Rep. gr. 52 ; Use of adhesives; Preparing undamaged windows for installation .

All vehicles (continued)

New windscreen

  • ⇒ General information - body; Rep. gr. 52 ; Use of adhesives; Preparing new windows for installation .

All vehicles (continued)

  • ⇒ General information - body; Rep. gr. 52 ; Use of adhesives; Preparing body flange for installation .
  • ⇒ General information - body; Rep. gr. 52 ; Use of adhesives; Installation instructions for bonded windows .
  • ⇒ General information - body; Rep. gr. 52 ; Use of adhesives; Minimum drying times for bonded windows .
  • Apply window adhesive all around to rear window ⇒ General information - body; Rep. gr. 52 ; Use of adhesives; Installation instructions for bonded windows; Materials for bonded windows .

Dimensions for cross-section of adhesive bead:

  • Height = 10 mm +-1 mm
  • Width = 6.5 mm +-0.5 mm

Spoiler design depends on model.

  • Guide rear window -1- at a distance to body flange in direction of -arrow A- under spoiler -2-.
  • Place rear window -1- with centring pins -3- in direction of -arrow B- on rear lid -4-.

Important

  • If the rear window has no centring pins, it must be secured against slipping.
Volkswagen ID.4. Removing and installing rear window
  • Check gaps with setting gauge - 3371- , observing ⇒ Rep.gr. 00 ; rear gaps while doing so.