Lower suspension link, swivel joint

In this manual: Lower suspension link, swivel joint
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
13steps
~78min
3/5difficulty
0204060801006044N·mlb·ft
Tightening torque found on this page
Done 0 of 13
  • Assembly overview - suspension link, swivel joint
  • Removing and installing suspension link
  • Removing and installing swivel joint
  • Removing and installing stone deflector for suspension link
  • Renewing front suspension link bush
  • Renewing suspension link bush, rear

Assembly overview - suspension link, swivel joint

The overview is shown for the left side of the vehicle as an example.

Volkswagen ID.4. Assembly overview - suspension link, swivel joint
  1. Wheel bearing housing
  • ⇒ Rep. gr. 40 ; Assembly overview - wheel bearing
  • ⇒ Rep. gr. 40 ; Removing and installing wheel bearing housing
  1. Nut
  • Renew after removing
  • M12 × 1.5
  • Nut M12: 60 N·m
  • Nut M14: 110 N·m
  1. Bush
  2. Swivel joint
  • ⇒ Rep. gr. 40 ; Removing and installing swivel joint
  1. Nut
  • Qty. 3
  • Renew after removing
  • Nut M10: 40 N·m + 45º
  • Nut M12: 100 N·m
  1. Suspension link
  • ⇒ Rep. gr. 40 ; Removing and installing suspension link
  1. Stone deflector for suspension link
  2. ⇒ Rep. gr. 40 ; Removing and installing stone deflector for suspension link
  3. Spreader rivet
  • Qty. 3
  1. Bolt
  • Renew after removing
  • M14 × 1.5 × 85
  • 130 N·m +180º
  1. Bolt
  • Renew after removing
  • M 12 × 1.5 × 80
  • 70 N·m +180º
  1. Suspension link mounting, front
  • ⇒ Rep. gr. 40 ; Renewing front suspension link bush
  1. Suspension link mounting, rear
  • ⇒ Rep. gr. 40 ; Renewing suspension link bush, rear
  1. Subframe
  • ⇒ Rep. gr. 40 ; Assembly overview - subframe
  1. Nut
  • Renew after removing
  • M12 × 1.5
  1. Weld nut

Removing and installing suspension link

Front left speed sensor - G47- and front right speed sensor - G45- will henceforth be referred to as "speed sensor".

Front left vehicle level sender - G78- and front right vehicle level sender - G289- will henceforth be referred to as "vehicle level sender".

Removal and installation are described for the left side of vehicle as an example

Removing

  • Remove wheel ⇒ Rep. gr. 44 ; Removing and installing wheel .
  • Remove stone deflector for suspension link ⇒ Rep. gr. 40 ; Removing and installing stone deflector for suspension link .

Vehicles with vehicle level sender

  • Remove vehicle level sender from suspension link ⇒ Rep. gr. 43 ; Removing and installing front vehicle level sender [G78]/[G289] .

All vehicles (continued)

  • Unscrew nuts -3-.
  • Pull suspension link -2- downwards -arrow A- off swivel joint.
  • Pull wheel bearing housing -1- outwards in direction of -arrow B-.
  • Swing wheel bearing housing -1- outwards to relieve tension from suspension link -2-.
Volkswagen ID.4. Removing and installing suspension link
  • Unscrew bolt -4- while counter-holding at nut -2-.
  • Unscrew bolt -5-.
  • Pull suspension link -1- out of subframe -3-.
Volkswagen ID.4. Removing and installing suspension link

Installing

Install in reverse order of removal, observing the following:

Vehicles with vehicle level sender

  • Carry out required function/functions using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

All vehicles (continued)

Tightening torques

  • ⇒ Rep. gr. 40 ; Assembly overview - suspension link, swivel joint

Removing and installing swivel joint

Special tools and workshop equipment required

  • ball joint puller - 3287AFront

left vehicle level sender - G78- and front right vehicle level sender - G289- will henceforth be referred to as "vehicle level sender".

Removal and installation are described for the left side of vehicle as an example.

Tools and auxiliary equipment required:

  • Torx T40, commercially available

Removing

Vehicles with all-wheel drive:

  • Loosen threaded connection of drive shaft ⇒ Running gear, axles, steering; Rep. gr. 40 ; Drive shafts; Loosening and tightening threaded connections of drive shaft .

All vehicles (continued)

  • Remove wheel ⇒ Rep. gr. 44 ; Removing and installing wheel .
  • Remove stone deflector for suspension link ⇒ Rep. gr. 40 ; Removing and installing stone deflector for suspension link .

Vehicles with vehicle level sender

  • Unbolt left vehicle level sender from suspension link ⇒ Rep.

    gr. 43 ; Removing and installing front vehicle level sender [G78]/[G289] .

All vehicles (continued)

Vehicles with all-wheel drive:

  • Loosen threaded connection of drive shaft.
  • Press drive shaft out of wheel bearing unit ⇒ Running gear, axles, steering; Rep. gr. 40 ; Drive shaft; Removing and installing drive shaft .

All vehicles (continued)

  • Unscrew nuts -3-.
  • Pull suspension link -2- in direction of -arrow A- off swivel joint.
  • Pull wheel bearing housing -1- in direction of -arrow B-.
  • Swing wheel bearing housing -1- outwards to relieve tension from suspension link -2-.
  • Push suspension link upwards.
Volkswagen ID.4. Removing and installing swivel joint
  • Loosen nut -4- of swivel joint -2- without unscrewing it completely.

Important

  • To protect threads, nut -4- must remain screwed onto pin a few turns.
  • Counterhold with commercially available Torx T40 in the process.

NOTICE

Damage to wheel bearing housing from loosened bushes due to incorrectly applied ball joint puller.

  • Ball joint puller must be supported on bush and not on wheel bearing housing.
Volkswagen ID.4. Removing and installing swivel joint
  • Fit ball joint puller - 3287A- -A- with bottom support against bush -3-.
  • Press swivel joint -2- off wheel bearing housing -1- using ball joint puller - 3287A- -A-.
  • Unscrew nut -4-.

Installing

Install in reverse order of removal, observing the following

Vehicles with front vehicle level sender

  • Carry out required function/functions using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00 ; Access to diagnoses .

All vehicles (continued)

Tightening torques

  • ⇒ Rep. gr. 40 ; Assembly overview - suspension link, swivel joint

Removing and installing stone deflector for suspension link

Removing

Removal and installation are described for the left side of vehicle as an example.

Spreader rivets with pins for pressing inwards

  • Press pins -arrows- in all spreader rivets -2- inwards.
  • Lever off spreader rivets with commercially available plastic wedge, and detach stone deflector for front suspension link -1-.
  • Remove pins -arrows- from suspension link from above.
Volkswagen ID.4. Removing and installing stone deflector for suspension link

All vehicles (continued)

Spreader rivets with pins for pulling out

  • Pull out pins -arrows- of all spreader rivets -2-.
  • Lever off spreader rivets using commercially available plastic wedge, and detach stone deflector for suspension link -1-.
Volkswagen ID.4. Removing and installing stone deflector for suspension link

All vehicles (continued)

Installing

Install in reverse sequence of removal.

Renewing front suspension link bush

Special tools and workshop equipment required

  • Assembly tool - T10642-
  • centring pin - T10642/3-
  • press tool - VW412-
  • thrust piece - T10642/4-
  • thrust plate - VW401ARenewal

Renewal procedure is described for left side of vehicle as an example.

Removing

  • Remove suspension link ⇒ Rep. gr. 40 ; Removing and installing suspension link .
  • Note allocation of suspension link bushes.
Volkswagen ID.4. Renewing front suspension link bush
  1. Subframe
  2. Suspension link
  3. Suspension link mounting, rear
  4. Suspension link mounting, front
  • Screw centring element - T10642/3- -C- into gripping piece - T10642/1- -A-.
Volkswagen ID.4. Renewing front suspension link bush

For greater clarity, the illustration shows both sides of the vehicle.

-I- = left side of vehicle, -II- = right side of vehicle.

  • Position thrust piece - T10642/4- -A- on front suspension link bush -Figure I-.
Volkswagen ID.4. Renewing front suspension link bush

Important

  • Guide -1- must engage in recess in thrust piece - T10642/4- -A-.
  • Guide -1- faces towards vehicle exterior -C-.
  • Arrow on suspension link bush -2- must be aligned with notch in thrust piece - T10642/4- -A-.
  • Notch in thrust piece - T10642/4- on left suspension link faces in opposite direction of travel -B-.
  • Notch in thrust piece - T10642/4- on right suspension link faces in direction of travel -B-.
  • Insert centring pin - T10642/3- -B- through thrust piece - T10642/4- -A- into suspension link bush of suspension link -1- up to seat stop.
Volkswagen ID.4. Renewing front suspension link bush

For greater clarity, the illustration shows both sides of the vehicle.

-I- = left side of vehicle, -II- = right side of vehicle.

  • Use a commercially available felt-tip pen to make a marking -arrow- that is aligned with notch -C- in thrust piece - T10642/4- -A- on left and right -I and II- suspension link -1-.
Volkswagen ID.4. Renewing front suspension link bush
  • Position tube - T10642/2- -B- on thrust plate - VW401A- -G-.
  • Fit suspension link -2- with thrust piece - T10642/4- -D- onto tube - T10642/2- -B-.
Volkswagen ID.4. Renewing front suspension link bush

Important

  • Bevelled edges of suspension link -2- must face upwards.
  • Insert gripping piece - T10642/1- -A- with centring element - T10642/3- -C- into thrust piece - T10642/4- -D-.
  • Press out front bonded rubber bush -1- using press tool - VW412- -H-.

Installing

For greater clarity, the illustration shows both sides of the vehicle.

-I- = left side of vehicle, -II- = right side of vehicle.

  • Position suspension link bush -3- on left -I- suspension link -2-.

Important

  • Marking -1- on suspension link bush must be aligned with previously made marking -arrow- on left or right suspension link -2-.
Volkswagen ID.4. Renewing front suspension link bush
  • Position tube - T10642/2- -A- on thrust plate - VW401A- -G-.
  • Fit suspension link -2- with thrust piece - T10642/4- -F- onto tube - T10642/2- -A-.

Important

  • Bevelled edges on suspension link -2- must face downwards.
  • Insert gripping piece - T10642/1- -D- with centring element - T10642/3- into thrust piece - T10642/4- -F-.
  • Press in front suspension link bush -1- using press tool - VW412- -E-.
Volkswagen ID.4. Renewing front suspension link bush
  • Install suspension link ⇒ Rep. gr. 40 ; Removing and installing suspension link .

Renewing suspension link bush, rear

Special tools and workshop equipment required

  • Assembly tool - T10642-
  • press tool - VW412-
  • thrust plate - VW401AID.

Removing

  • Remove suspension link ⇒ Rep. gr. 40 ; Removing and installing suspension link .
  • Note allocation of suspension link bushes.
  1. Subframe
  2. Suspension link
  3. Suspension link mounting, rear
  4. Suspension link mounting, front
    Volkswagen ID.4. Renewing suspension link bush, rear
  • Screw centring element - T10642/5- -E- into gripping piece - T10642/1- -A-.
Volkswagen ID.4. Renewing suspension link bush, rear
  • Position tube - T10642/2- -B- on thrust plate - VW401A- -G-.
  • Fit suspension link -2- with thrust piece - T10642/6- -F- onto tube - T10642/2- -B-.
Volkswagen ID.4. Renewing suspension link bush, rear

Important

  • Bevelled edges of suspension link -2- must face downwards.
  • Insert gripping piece - T10642/1- -A- with centring element - T10642/5- -E- into thrust piece - T10642/6- -F-.
  • Press out rear suspension link bush -1- with press tool - VW412- -H-.
Volkswagen ID.4. Renewing suspension link bush, rear

Installing

  • Position tube - T10642/2- -B- on thrust plate - VW401A- -G-.
  • Fit suspension link -2- with thrust piece - T10642/6- -F- onto tube - T10642/2- -B-.

Important

  • Bevelled edges of suspension link -2- must face downwards.
  • Insert gripping piece - T10642/1- -A- with centring element - T10642/5- -E- into thrust piece - T10642/6- -F-.
  • Press in rear suspension link bush -1- with press tool - VW412- -H-.
  • Install suspension link ⇒ Rep. gr. 40 ; Removing and installing suspension link .