Adaptive cruise control

In this manual: Adaptive cruise control
Basic information on body repairs — 1Explanation of symbols — 1Overview of materials used — 1Joining and separating techniques — 1Surface repair — 1Corrosion protection — 1Noise insulation — 1Plastic repair — 1General notes - windows — 1Self-adhesive components — 1Noises — 1Resistance spot welding — 1Solid rivet — 1Pop rivet — 1Incorrect riveting — 1Overview of riveting attachments — 1Making a flow-drill screw connection, pre-drilled hole in upper part — 1Distinction of types of plastic — 1Processing instructions - original products — 1Preparing plastic repair — 1Repairing deformations — 1Bonding plastic attachments — 1Welding plastic attachments — 1Glass repair- Introduction — 1Carrying out glass repair — 1General notes on the use of adhesives — 1Preparing old undamaged windows for installing — 1Preparing new windows for installation — 1Installation instructions for bonded windows — 1Bonding log — 1Preparing gas strut for disposal — 1Preparing rear lid drive unit VX69/rear lid drive unit 2 VX77 for disposal — 1Causes of water ingress — 1Locating water ingress — 1Interior equipment — 1Compartments/covers — 1Equipment — 1Centre console — 1Front centre armrest — 1Interior mirror — 1Passenger protection — 1Seat belts — 1Child seat anchors — 1Airbag system — 1Airbag control unit — 1Front airbag, driver side — 1Front passenger airbag — 1Side airbags — 1Curtain airbags — 1Airbag crash sensors — 1Seat belt verification — 1Seat occupied recognition — 1Trim, insulation — 1Front door trims — 1Rear door trims — 1Dash panel — 1Central tube for dash panel — 1Interior trims — 1Luggage compartment trims — 1Roof trims — 1Seat frames — 1Overview of seat variants — 1Front seats — 1Rear seats — 1Seat - padding, covers — 1Front seat covers and padding — 1Rear seat covers and padding — 1Technical data — 1Body - front — 1Lock carrier — 1Wings — 1Technical data — 1Air conditioning system — 1Overview of fitting locations - air conditioning system, R134a/R1234yf — 1Overview of fitting locations - air conditioning system, R744 — 1Refrigerant circuit, R134a/R1234yf — 1Refrigerant circuit, R744 — 1Valve unit of heat pump, R744 — 1Air conditioner compressor, R134a/R1234yf — 1Air conditioner compressor, R744 — 1Control motors, vehicles without air conditioner operating unit at rear — 1Control motors, vehicles with air conditioner operating unit at rear — 1Front heater and air conditioning unit, R134a/R1234yf — 1Front heater and air conditioning unit, R744 — 1Air duct — 1Coolant circuit, rear-wheel drive — 1Coolant circuit, all-wheel drive — 1Operating and display unit — 1Other controlling and regulating components — 1Air quality improvement system — 1Technical data — 1Brake test — 1Electrical components — 1Anti-lock brake system — 1Control unit and hydraulic unit — 1Separating control unit from and connecting to hydraulic unit — 1Connecting brake lines to hydraulic unit — 1Sensors — 1Brakes - mechanism — 1Front brake — 1Rear brake — 1Parking brake — 1Brake pedal — 1Brakes - hydraulics — 1Brake servo and brake master cylinder — 1Hydraulic system — 1Technical data — 1Fitting locations — 1Senders/sensors/control units — 1Adaptive cruise control — 1Reversing camera system — 1Front camera for driver assist systems — 1Overhead view camera — 1Electric drive systems- Safety information and repair notes — 1Classifying high-voltage batteries — 1Packaging high-voltage batteries — 1Packaging critical high-voltage batteries with "Warning" status — 1Bulkhead — 1Bonnet, rear lid — 1Bonnet — 1Rear lid — 1Charging flap unit — 1Front doors, door components, central locking — 1Door — 1Door components — 1Central locking — 1Rear doors, door components — 1Door — 1Door components — 1Sunroof — 1Sliding sunroof — 1Water drain hoses — 1Bumpers — 1Bumper, front — 1Bumper, rear — 1Glazing — 1Windscreen — 1Rear windscreen — 1Side windows — 1Door windows — 1Exterior equipment — 1Spoiler — 1Mouldings, trims, extensions — 1Underbody cladding — 1Roof moulding and roof railing — 1Exterior mirror — 1Wheel housing liner — 1Lettering and emblems — 1Towing bracket — 1Technical data — 1Vehicle identification data — 1Safety information — 1Body parts and materials — 1Technical data — 1Alignment jig — 1Body - front — 1Overview of fitting locations — 1Longitudinal member cross panel — 1Longitudinal member — 1Assembly overview - front right longitudinal member, part section — 1Battery tray — 1Front wheel housing — 1Body - centre — 1Overview of fitting locations — 1Roof — 1A-pillar — 1B-pillar — 1Side member — 1Body - rear — 1Rear cross member — 1Rear cross panel — 1Luggage compartment floor — 1Rear longitudinal member — 1Side panel — 1Rear wheel housing — 1Technical data — 1Controls, housing — 1Removing and installing gearbox — 1Gearbox housing, clutch housing — 1Final drive - differential — 1Technical data — 1Controls, housing — 1Gearbox housing, clutch housing — 1Gear oil — 1Final drive - differential — 1Explanation of symbols — 1Paintwork structure — 1Areas exposed to stone chipping — 1Seam seals, front body — 1Seam seals, bonnet, inner side — 1Seam seals, doors — 1Seam seals, underbody — 1Underseal — 1Cavity sealing — 1Technical data — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Overview of fitting locations - components/control units in centre section of vehicle — 1Overview of fitting locations - components/control units in rear section of vehicle — 1Components/control units — 1Multifunction steering wheel — 1Technical data — 1Identification — 1Electrical components — 1Hazard classification of high-voltage system — 1Removing and installing engine — 1Removing and installing front motor — 1Removing and installing rear motor — 1Removing and installing rear motor — 1Front assembly mountings — 1Cooling — 1Cooling system/coolant — 1Coolant pump/coolant regulation — 1Radiator, radiator fan — 1Electric drive systems — 1High-voltage components, charging unit for high-voltage battery and voltage converter — 1High-voltage components, charging unit for high-voltage battery with integrated voltage converter — 1Warning stickers — 1High-voltage battery unit, edge of upper part of battery housing without wax — 1High-voltage battery components, edge of upper part of battery housing without wax — 1High-voltage battery unit, edge of upper part of battery housing with wax — 1High-voltage battery components, edge of upper part of battery housing with wax — 1Power and control electronics for electric drive — 1Electric drive motor — 1Electric drive motor — 1Motor control unit — 1De-energising high-voltage system — 1Potential equalisation lines — 1Charging socket, with charging cable — 1Charging socket, with separate charging cable — 1Charging unit for high-voltage battery — 1Charging unit for high-voltage battery, with integrated voltage converter — 1Vehicle noise/engine sound — 1Accelerator pedal — 1Voltage converter — 1High-voltage cables, all-wheel drive — 1High-voltage cables, rear-wheel drive — 1Technical data — 1Starter, current supply, CCS — 1Assembly overview - battery — 1Removing and installing battery [A] — 1Disconnecting and connecting battery — 1Removing and installing earth wire with battery monitor control unit [J367] — 1Gauges, instruments — 1Dash panel insert — 1Horn — 1Windscreen wash/wipe system — 1Windscreen wiper system — 1Windscreen washer system — 1Rear window wiper system ID4 — 1Rear window washer system — 1Lights, bulbs, switches - exterior — 1Headlights — 1Lights in exterior mirror — 1Tail lights — 1High-level brake light — 1Number plate light — 1Entry and start authorisation system — 1Steering column switch module — 1Towing bracket — 1Lights, bulbs, switches - interior — 1Lights — 1Controls — 1Anti-theft alarm system — 1Cigarette lighter, socket — 1Wiring — 1Relay carriers, fuse holders, electronics boxes — 1Control units — 1Technical data — 1Front suspension — 1Front axle — 1Subframe — 1Suspension strut, upper suspension link — 1Lower suspension link, swivel joint — 1Wheel bearing — 1Drive shaft — 1Anti-roll bar — 1Rear suspension — 1Rear axle — 1Subframe — 1Anti-roll bar — 1Suspension link, track rod — 1Suspension strut, shock absorber, spring — 1Wheel bearing assembly, trailing arm — 1Drive shaft — 1Self-levelling suspension — 1Electronic damping control — 1Vehicle level sender — 1Wheels, tyres, vehicle geometry — 1Wheel alignment — 1Wheels, tyres — 1Steering — 1Steering wheel — 1Steering column — 1Steering rack — 1
~6min read
  • Necessity of calibration
  • Adjusting/calibrating adaptive cruise control unit

Necessity of calibration

  • 1 Adaptive cruise control must be calibrated after the following work has been performed
  • 2 Front camera for driver assist systems must be calibrated after the following work has been performed
  • 3 The overhead view camera must be calibrated after the following work has been performed:
  • 4 The reversing camera must be calibrated after the following work has been performed:
  • 5 Vehicle
  • 6 Calibration environment:

1 Adaptive cruise control must be calibrated after the following work has been performed:

Important

Calibration is normally carried out dynamically.

  • Changes to wheel alignment on rear axle.
  • Ride height adjustment on one axle by more than 5 mm.
  • Ride height adjustment on both axles by more than 10 mm.
  • Removal and installation or renewal of front bumper cover.
  • After renewal of adaptive cruise control unit -J428-.

⇒ Rep. gr. 98; Adjusting/calibrating adaptive cruise control unit

2 Front camera for driver assist systems must be calibrated after the following work has been performed:

Important

Calibration is normally carried out dynamically.

  • Changes to wheel alignment on rear axle.
  • Ride height adjustment on one axle by more than 5 mm.
  • Ride height adjustment on both axles by more than 10 mm.
  • Removal and installation or renewal of camera.
  • Removal and installation of windscreen.
  • Repair work on components in which the camera is installed, or components which affect the installation position of the camera.
  • Event memory shows no or incorrect basic setting/adaptation.

⇒ Rep. gr. 98; Calibrating front camera for driver assist systems [R242]

3 The overhead view camera must be calibrated after the following work has been performed

  • Changes to wheel alignment on rear axle.
  • Ride height adjustment on one axle by more than 5 mm.
  • Ride height adjustment on both axles by more than 10 mm.
  • Removal and installation or renewal of front overhead view camera -R243-, left overhead view camera -R244-, right overhead view camera -R245- or rear overhead view camera.
  • Repair work on components in which front overhead view camera -R243-, left overhead view camera -R244-, right overhead view camera -R245- or rear overhead view camera -R246- is installed or that influence the camera installation position.
  • Renewal of control unit for overhead view camera.
  • Offset in overlapping area of individual camera images.
  • Flashing control unit for overhead view camera.
  • Writing datasets into control unit for overhead view camera.

4 The reversing camera must be calibrated after the following work has been performed:

  • Changes to wheel alignment on rear axle.
  • Ride height adjustment on one axle by more than 5 mm.
  • Ride height adjustment on both axles by more than 10 mm.
  • Removal and installation or renewal of camera.
  • Repair work on components in which the camera is installed, or components which affect the installation position of the camera.

3 Vehicle:

Important

  • The parking brake must be applied.
  • Steering wheel must be in centre position with wheels pointing straight ahead.
  • All doors, bonnet and rear lid must be closed.
  • There must be no-one in the vehicle.
  • The vehicle must not be loaded (kerb weight).
  • Vehicle's drive system must be activated.
  • System must active, and active status must be shown on display unit.
  • Vehicle must not be moved during calibration.
  • Exterior mirrors must be folded out.
  • Camera lenses must be clean.
  • Battery charger must be connected and switched on ⇒ Electrical system; Rep. gr. 27; Battery; Charging battery A.

4 Calibration environment:

Important

  • Calibration surface must be flat.
  • Calibration environment must be free of objects to prevent false detection of lines.
  • Lighting conditions in calibration environment must be consistent.

    Avoid significant lighting differences caused by spotlights or direct lighting.

Light reflections will impair the image recognition of the overhead view camera and might make calibration impossible.

Adjusting/calibrating adaptive cruise control unit

Dynamic calibration of adaptive cruise control

Preparation

Important

  • Observe ⇒ Rep. gr. 98; Necessity of calibration.
  • There must be no entries in the event memory that would hinder calibration.
  • Check sensors, holders and fasteners for damage, manipulation and secure fit.

Calibrating

Important

  • ⇒ Vehicle diagnostic tester connected.
  • Carry out function "Calibrate adaptive cruise control" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.

Static calibration of adaptive cruise control

Special tools and workshop equipment required

  • ACC reflective mirror -VAS 6430/10-
  • Setting device -VAS 6430-

Adaptive cruise control unit -J428- is called sensor in this document.

Preparation

Important

  • Observe ⇒ Rep. gr. 98; Necessity of calibration.
  • If the position of the ACC reflecting mirror -VAS 6430/10- on alignment beam is changed during the calibration, the setting of setting device -VAS 6430- must be checked again (e.g. spirit levels, individual toe values on alignment beam, etc.).
  • There must be no entries in the event memory that would hinder calibration.
  • Check sensors, holders and fasteners for damage, manipulation and secure fit.

Calibration without preceding wheel alignment

  • Select program on alignment computer.
  • Observe test prerequisites for wheel alignment ⇒ Running gear, axles, steering; Rep. gr. 44; Wheel alignment; Test prerequisites.
  • Verify whether there is sufficient space between vehicle and setting device.

Important

  • Distance between setting device and sensor must be 120 cm +- 2.5 cm.
  • If there is not enough space, move the vehicle backwards onto the wheel alignment platform as required to make space.
  • Drive vehicle straight onto wheel alignment platform.
  • Turn wheels to straight-ahead position.
  • Install quick-release clamps to rear wheels.
  • Install wheel alignment sensors to quick-release clamps.
  • Install reflector mirror centrally and parallel to setting device.

All vehicles (continued)

  • Install reflector mirror -1- centrally and parallel to setting device.
Volkswagen ID.4. All vehicles (continued)
  • Position setting device with reflector mirror -1- parallel to sensor at distance -a-.

Important

  • Dimension -a- = 120 cm +- 2.5 cm
  • Mount measurement transducers -1- of front wheels on alignment beam.
Volkswagen ID.4. All vehicles (continued)
  • Turn adjuster screws -1-, -2- and -3- until spirit levels -A- and -B- on reflector mirror -5- are horizontal.
Volkswagen ID.4. All vehicles (continued)

Vehicles with sensor behind badge:

  • Adjust reflector mirror on side of alignment beam so that laser beam contacts centre of badge.
  • ⇒ Rep. gr. 98; Overview of fitting locations - senders, sensors and control units in front section of vehicle

All vehicles (continued)

Vehicles with sensor behind bumper cover:

  • Adjust reflector mirror on side of alignment beam so that laser beam contacts centre below badge.
  • ⇒ Rep. gr. 98; Overview of fitting locations - senders, sensors and control units in front section of vehicle

All vehicles (continued)

  • Bring spirit levels of wheel alignment sensors into horizontal position.
  • Turn adjuster screw -4- until display on wheel alignment computer is within tolerance.
Volkswagen ID.4. All vehicles (continued)
  • Turn adjuster screws -1-, -2- and -3- until spirit levels -A- and -B- on reflector mirror -5- are horizontal.
  • Make sure that spirit levels -A- and -B- are horizontal and that the laser beam is centred on trim.

Important

  • If laser beam is not centred on trim, adjust reflector mirror -5- anew.

Calibrating

Important

  • ⇒ Vehicle diagnostic tester connected.
  • Carry out function "Calibrate adaptive cruise control" using ⇒ Vehicle diagnostic tester ⇒ Rep. gr. 00; Access to diagnoses.