Driver Information & Multimedia :: Meter, Warning Lamp & Indicator

Dtc/circuit Diagnosis - Meter/m&a (combination Meter) ++

In this manual: Driver Information & Multimedia :: Meter, Warning Lamp & Indicator
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
210steps
~1260min
4/5difficulty
Done 0 of 210

B2202-11 Fuel Level Sensor

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2202-11

Fuel level sensor

(Fuel level sensor)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Fuel level sensor signal
Threshold Short circuit
Diagnosis delay time —

POSSIBLE CAUSE

  • Fuel level sensor unit and fuel pump

  • Combination meter

  • Harness or connectors

FAIL-SAFE

Low fuel level warning displays

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 1 minute or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B2202-11 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident .

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK FUEL LEVEL SENSOR SIGNAL CIRCUIT

Check the fuel level sensor signal circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

B2202-13 Fuel Level Sensor

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2202-13

Fuel level sensor

(Fuel level sensor)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Fuel level sensor signal
Threshold Open circuit
Diagnosis delay time —

POSSIBLE CAUSE

  • Fuel level sensor unit and fuel pump

  • Combination meter

  • Harness or connectors

FAIL-SAFE

Low fuel level warning displays

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 1 minute or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B2202-13 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK FUEL LEVEL SENSOR SIGNAL CIRCUIT

Check the fuel level sensor signal circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

B2205-29 Vehicle Speed

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2205-29

Nissan Pathfinder Vehicle SPEED

(Vehicle speed)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Nissan Pathfinder Vehicle speed display signal
Threshold An abnormal Nissan Pathfinder vehicle speed signal is input from ECM
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • ECM

  • ABS actuator and electric unit (control unit)

  • Wheel sensor

FAIL-SAFE

Reset to zero of the speedometer by suspending communication.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B2205-29 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident .

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS OF ECM

CONSULT

Select “Self Diagnostic Result” mode of “ENGINE.”

Is DTC detected?

YES>>

Perform diagnosis procedure on the detected DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

CONSULT

Select “Self Diagnostic Result” mode of “ABS.”

Is DTC detected?

YES>>

Perform diagnosis procedure on the detected DTC. Refer to DTC Index.

NO>>

Inspection End.

B2205-87 Vehicle Speed

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2205-87

Nissan Pathfinder Vehicle SPEED

(Vehicle speed)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Nissan Pathfinder Vehicle speed display signal
Threshold Nissan Pathfinder Vehicle speed display signal is not input from ECM
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

ECM

FAIL-SAFE

Reset to zero of the speedometer by suspending communication.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B2205-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS OF ECM

CONSULT

Select “Self Diagnostic Result” mode of “ENGINE.”

Is DTC detected?

YES>>

Perform diagnosis procedure on the detected DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

CONSULT

Select “Self Diagnostic Result” mode of “ABS.”

Is DTC detected?

YES>>

Perform diagnosis procedure on the detected DTC. Refer to DTC Index.

NO>>

Inspection End.

B220a-11 Illumination Output Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B220A-11

ILLUMINATION OUTPUT CIRCUIT

(Illumination output circuit)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Illumination control signal
Threshold Short circuit
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Combination meter

  • Harness or connectors

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B220A-11 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK ILLUMINATION CONTROL SIGNAL CIRCUIT

  1. Disconnect harness connector of the combination meter Nissan Pathfinder vehicle side and all the connectors connected to illumination control signal circuit.

  2. Check continuity between combination meter harness connector and ground.

    Combination meter Ground Continuity
    Connector Terminal
    M24 1 No

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

B220b-23 Trip Reset Sw

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B220B-23

Trip reset SW

(Trip reset switch)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Steering switch signal
Threshold Switch stuck ON 5 minutes
Diagnosis delay time 5 minutes or more

POSSIBLE CAUSE

  • Steering switch

  • Combination meter

  • Harness or connectors

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 5 minutes or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B220B-23 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK STEERING SWITCH SIGNAL CIRCUIT

Check the steering switch signal circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

B220c-23 Illumination up Sw

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B220C-23

Illumination up SW

(Illumination up switch)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Illumination control switch signal (+)
Threshold Switch stuck ON 5 minutes
Diagnosis delay time 5 minutes or more

POSSIBLE CAUSE

  • Rotary light switch (illumination control switch)

  • Combination meter

  • Harness or connectors

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 5 minutes or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B220C-23 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident .

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK ILLUMINATION CONTROL SWITCH SIGNAL CIRCUIT

Check the illumination control switch signal circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

B220d-23 Illumination Down Sw

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B220D-23

Illumination down SW

(Illumination down switch)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Illumination control switch signal (-)
Threshold Switch stuck ON 5 minutes
Diagnosis delay time 5 minutes or more

POSSIBLE CAUSE

  • Rotary light switch (illumination control switch)

  • Combination meter

  • Harness or connectors

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 5 minutes or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B220D-23 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK ILLUMINATION CONTROL SWITCH SIGNAL CIRCUIT

Check the illumination control switch signal circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

B2210-11 Outside Temp Sensor

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2210-11

Outside temp sensor

(Outside temperature sensor)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Ambient sensor signal
Threshold Short circuit
Diagnosis delay time —

POSSIBLE CAUSE

  • Ambient sensor

  • Combination meter

  • Harness or connectors (The sensor circuit is shorted)

FAIL-SAFE

“––” is displayed

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B2210-11 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK AMBIENT SENSOR SIGNAL CIRCUIT

Check the ambient sensor signal circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

B221a-23 Steering Sw Input1

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B221A-23

Steering SW input1

(Steering switch input1)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Steering switch signal
Threshold Switch stuck ON for 5 minutes
Diagnosis delay time 5 minutes or more

POSSIBLE CAUSE

  • Steering switch

  • Combination meter

  • Harness or connectors

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 5 minutes or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B221A-23 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK STEERING SWITCH SIGNAL A CIRCUIT

Check the steering switch signal A circuit. Refer to Component Function Check.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation

NO>>

Repair or replace malfunctioning parts.

B221b-23 Steering Sw Input2

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B221B-23

Steering SW input2

(Steering switch input2)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Steering switch signal
Threshold Switch stuck ON for 5 minutes
Diagnosis delay time 5 minutes or more

POSSIBLE CAUSE

  • Steering switch

  • Combination meter

  • Harness or connectors

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 5 minutes or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B221B-23 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK STEERING SWITCH SIGNAL B CIRCUIT

Check the steering switch signal B circuit. Refer to Component Function Check.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

B2223-1c Combination Meter

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2223-1C

Combination meter

(Combination meter)
Diagnosis condition When ignition switch is ON.
Signal (terminal) —
Threshold TFT error is detected
Diagnosis delay time —

POSSIBLE CAUSE

Combination meter

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B2223-1C detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Erase the self-diagnostic results.

  3. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Inspection End.

B2227-86 Av Communication

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2227-86

AV communication

(AV communication)
MISSING MESSAGE Diagnosis condition When ignition switch is ON.
Signal (terminal) AV communication
Threshold Abnormal communication is detected
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

Harness or connectors

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B2227-86 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK AV COMMUNICATION CIRCUIT

Check the AV communication circuit.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

B2227-87 Av Communication

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2227-87

AV communication

(AV communication)
MISSING MESSAGE Diagnosis condition When ignition switch is ON.
Signal (terminal) AV communication
Threshold Abnormal communication is detected
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

Harness or connector

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B2227-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK AV COMMUNICATION CIRCUIT

Check the AV communication circuit.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

B2231-16 Battery Voltage

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2231-16

Battery voltage

(Battery voltage)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Battery power supply
Threshold 8 V or less
Diagnosis delay time —

POSSIBLE CAUSE

  • Combination meter

  • Harness or connectors

  • Charging system

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B2231-16 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK BATTERY

Check battery. Refer to Work Flow.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the malfunctioning parts.

CHECK CHARGING SYSTEM

Check charging system condition. Refer to Work Flow (With 165-DSS-5000P) or Work Flow (Without 165-DSS-5000P).

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace the malfunctioning parts.

CHECK COMBINATION METER POWER SUPPLY CIRCUIT

Check combination meter power supply circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace the malfunctioning parts.

B2231-17 Battery Voltage

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2231-17

Battery voltage

(Battery voltage)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Battery power supply
Threshold 16 V or more
Diagnosis delay time —

POSSIBLE CAUSE

Battery voltage is too high.

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B2231-17 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK BATTERY

Check battery. Refer to Work Flow.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the malfunctioning parts.

CHECK CHARGING SYSTEM

Check charging system condition. Refer to Work Flow (With 165-DSS-5000P) or Work Flow (Without 165-DSS-5000P).

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace the malfunctioning parts.

CHECK COMBINATION METER POWER SUPPLY CIRCUIT

Check combination meter power supply circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace the malfunctioning parts.

B2267-29 Tacho Meter

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2267-29

TACHO METER

(Tacho meter)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Engine speed signal
Threshold ECM continuously transmits abnormal engine speed signals
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

Crankshaft position sensor (POS)

FAIL-SAFE

Reset to zero of the tachometer by suspending communication.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Start engine and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B2267-29 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS OF ECM

CONSULT

Select “Self Diagnostic Result” mode of “ENGINE.”

Is DTC detected?

YES>>

Perform diagnosis procedure on the detected DTC. Refer to DTC Index.

NO>>

Inspection End.

B2267-87 Tacho Meter

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2267-87

TACHO METER

(Tacho meter)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Engine speed signal
Threshold Engine speed signal is not input from ECM
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Crankshaft position sensor (POS)

  • ECM

FAIL-SAFE

Reset to zero of the tachometer by suspending communication.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Start engine and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B2267-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS OF ECM

CONSULT

Select “Self Diagnostic Result” mode of “ENGINE.”

Is DTC detected?

YES>>

Perform diagnosis procedure on the detected DTC. Refer to DTC Index.

NO>>

Inspection End.

B2268-29 Water Temp Meter

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2268-29

WATER TEMP METER

(Water temp meter)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Engine coolant temperature signal
Threshold ECM continuously transmits abnormal engine coolant temperature signals
Diagnosis delay time 60 seconds or more

POSSIBLE CAUSE

ECM

FAIL-SAFE

  • When reception time of an abnormal signal is 60 seconds or less, the last value received.

  • When reception time of an abnormal signal is more than 60 seconds, reset to zero.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 1 minute or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B2268-29 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS OF ECM

CONSULT

Select “Self Diagnostic Result” mode of “ENGINE.”

Is DTC detected?

YES>>

Perform diagnosis procedure on the detected DTC. Refer to DTC Index.

NO>>

Inspection End.

B2268-87 Water Temp Meter

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2268-87

WATER TEMP METER

(Water temp meter)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Engine coolant temperature signal
Threshold Engine coolant temperature signal is not input from ECM
Diagnosis delay time 60 seconds or more

POSSIBLE CAUSE

  • Engine coolant temperature sensor

  • ECM

FAIL-SAFE

  • When reception time of an abnormal signal is 60 seconds or less, the last value received.

  • When reception time of an abnormal signal is more than 60 seconds, reset to zero.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 1 minute or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B2268-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS OF ECM

CONSULT

Select “Self Diagnostic Result” mode of “ENGINE.”

Is DTC detected?

YES>>

Perform diagnosis procedure on the detected DTC. Refer to DTC Index.

NO>>

Inspection End.

B226a-82 Adas Clk

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B226A-82

ADAS CLK

(Advanced driver assistance systems clock)
Diagnosis condition When ignition switch is ON.
Signal (terminal) —
Threshold Abnormal ADAS clock signal is detected.
Diagnosis delay time —

POSSIBLE CAUSE

Abnormal ADAS clock signal is detected.

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC B226A-82 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM SELF-DIAGNOSIS OF ADAS CONTROL UNIT

CONSULT

Select “Self Diagnostic Result” mode of “ICC/ADAS 2”.

Is DTC detected?

YES>>

Perform diagnosis procedure on the detected DTC. Refer to DTC Index.

NO>>

Inspection End.

U1010-49 Control Unit (can)

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U1010-49

CONTROL UNIT (CAN)

[Control unit (CAN)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) —
Threshold When detecting error during the initial diagnosis
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

Combination meter

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U1010-49 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Erase the self-diagnostic results.

  3. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Inspection End.

U1321-55 Configuration Unfinished

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U1321–55

Config unfinished

(Configuration unfinished)
Diagnosis condition When ignition switch is ON.
Signal (terminal) —
Threshold Configuration is incomplete
Diagnosis delay time —

POSSIBLE CAUSE

The configuration for combination meter is not done.

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Select “Self Diagnostic Result” mode of “METER M&A”.

  4. Check DTC.

Is DTC "U1321-55" detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM CONFIGURATION OF COMBINATION METER

CONSULT

Perform configuration of combination meter. Refer to Work Procedure.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC "U1321-55" detected?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Inspection End.

U2118-87 Can Comm Err (intelligent Key)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2118-87

CAN comm err (Intelligent Key)

[CAN communication error (Intelligent key)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER M&A”.

  3. Check DTC.

Is DTC U2118-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2118-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U213d-87 Can Comm Err (adb)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U213D-87

CAN comm err (ADB)

[CAN communication error (ADB)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER M&A”.

  3. Check DTC.

Is DTC U213D-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U213D-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2140-87 Can Comm Err (ecm)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2140-87

CAN comm err (ECM)

[CAN communication error (Engine control module)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U2140-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2140-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2141-87 Can Comm Err (tcm)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2141-87

CAN comm err (TCM)

[CAN communication error (Transmission control module)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U2141-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2141-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2148-87 Can Comm Err (brake Control Unit)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2148-87

CAN comm err (brake control unit)

[CAN communication error (brake control unit)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U2148-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2148-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U214a-87 Can Comm Err (awd/4wd)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U214A-87

CAN comm err (AWD/4WD)

[CAN communication error (AWD/4WD)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U214A-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U214A-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U214f-87 Can Comm Err (bcm)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U214F-87

CAN comm err (BCM)

[CAN communication error (BCM)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U214F-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U214F-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2150-87 Can Comm Err (air Bag)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2150-87

CAN comm err (AIR BAG)

[CAN communication error (Air Bag)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U2150-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2150-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2152-83 Can Comm Err (adas Control Unit)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2152-83

CAN comm err (ADAS control unit)

[CAN communication error (Advanced driver assistant system control unit)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U2152-83 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2152-83 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2152-87 Can Comm Err (adas Control Unit)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2152-87

CAN comm err (ADAS control unit)

[CAN communication error (Advanced driver assistant system control unit)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U2152-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2152-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2153-87 Can Comm Err (hvac) Ch1

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2153-87

CAN comm err (HVAC) ch1

[CAN communication error (Heating ventilating and air-conditioning system) ch1]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U2153-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2153-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2154-87 Can Comm Err (miu)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2154-87

CAN comm err (MIU)

[CAN communication error (MIU)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U2154-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2154-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2159-87 Can Comm Err (steering Control Unit)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2159-87

CAN comm err (steering control unit)

[CAN communication error (Steering control unit)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U2159-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2159-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U215b-87 Can Comm Err (ipdm E/r)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U215B-87

CAN comm err (IPDM E/R)

[CAN communication error (Intelligent power distribution module engine room)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U215B-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U215B-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2165-87 Can Comm Err (sonar)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2165-87

CAN comm err (sonar)

[CAN communication error (sonar)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U2165-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2165-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2169-87 Can Comm Err (psd/mhb)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2169-87

CAN comm err (PSD/MHB)

[CAN communication error (PSD/MHB)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U2169-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2169-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U216b-87 Can Comm Err (front Camera)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U216B-87

CAN comm err (front camera)

[CAN communication error (front camera)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U216B-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U216B-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U216e-87 Can Comm Err (side Radar)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U216E-87

CAN comm err (side radar)

[CAN communication error (side radar)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U216E-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U216E-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2173-87 Can Comm Err (display)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2173-87

CAN comm err (display)

[CAN communication error (display)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U2173-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2173-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2175-87 Can Comm Err (avm)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2175-87

CAN comm err (AVM)

[CAN communication error (AVM)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U2175-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2175-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2176-87 Can Comm Err (ccm/st Angle Sensor)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2176-87

CAN comm err (CCM/ST angle sensor)

[CAN communication error (Chassis control module/ steering angle sensor)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U2176-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2176-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U2193-87 Can Comm Err (adp Driver Seat)

DTC Description

CAN (Controller Area Network) is a serial communication system for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication system with high data communication speed and excellent error detectability. Many electronic control units are equipped onto Nissan Pathfinder vehicles, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with two communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2193-87

CAN comm err (ADP driver seat)

[CAN communication error (Automatic driver positioner driver seat)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) CAN communication signal
Threshold When combination meter is not transmitting or receiving
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Refer to Fail-Safe.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “METER/M&A”.

  3. Check DTC.

Is DTC U2193-87 detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC U2193-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.