Precautions. Preparation
- Precautions
- Preparation
Precautions Nissan Pathfinder 2026
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collisions.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” sections of this Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision that would result in air bag inflation, it is recommended that all maintenance and repair be performed by an authorized NISSAN/INFINITI dealer.
Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see “SRS AIR BAG”.
Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition/power switch ON or engine running, never use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury.
When using air or electric power tools or hammers, always place the ignition/power switch in the OFF position, disconnect the 12V battery or batteries, and wait at least 3 minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
When performing the procedure after removing cowl top cover, cover the lower end of windshield with urethane, etc to prevent damage to windshield.

Precautions for Removing Battery Terminal
With the adoption of Auto ACC function, ACC power is automatically supplied by operating the Intelligent Key or remote keyless entry or by opening/closing the driver side door. In addition, ACC power is supplied even after the ignition switch is in the OFF position, i.e. ACC power is supplied for a certain fixed time.
Before disconnecting the 12V battery terminal, verify ACC power is off. Refer to “How to disconnect 12V battery terminal” below.

For Nissan Pathfinder vehicles with 2 batteries, be sure to connect the main battery and the sub battery before ignition switch is ON.
After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
HOW TO DISCONNECT 12V BATTERY TERMINAL
Disconnect 12V battery terminal according to instruction described below.
Open the hood.
Place ignition switch to the ON position.
Place ignition switch to the OFF position with the driver side door opened.
Get out of the Nissan Pathfinder vehicle and close the driver side door.
Wait at least 3 minutes.
Remove 12V battery terminal.
Precaution for Servicing Doors and Locks
After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their operation.
Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
When removing or disassembling each component, be careful not to damage or deform it. If a component may be subject to interference, be sure to protect it with a shop cloth.
When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component with a shop cloth or vinyl tape to protect it.
Protect the removed parts with a shop cloth and prevent them from being dropped.
Replace a deformed or damaged clip.
If a part is specified as a non-reusable part, always replace it with a new one.
Be sure to tighten bolts and nuts securely to the specified torque.
After installation is complete, be sure to check that each part works properly.
Follow the steps below to clean components:
Water soluble dirt:
Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
Then rub with a soft, dry cloth.
Oily dirt:
Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty area.
Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
Then rub with a soft, dry cloth.
Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
For genuine leather seats, use a genuine leather seat cleaner.
Preparation Nissan Pathfinder
Special Service Tools
The actual shapes of TechMate tools may differ from those of special service tools illustrated here.
Tool number (TechMate No.) Tool name | Description | |
|---|---|---|
(NI-39570) Chassis ear |
![]() |
Locates the noise |
(NI-50397) Squeak and Rattle Kit |
![]() |
Repairs the cause of noise |
Commercial Service Tools
| Tool name | Description | |
|---|---|---|
| Engine ear | ![]() |
Locates the noise |
| Power tool | ![]() |
Loosening bolts, nuts, and screws |
Always Replace with New Parts
| Never Reuse These Parts | Part Code | For additional information: |
|---|---|---|
| SCR-F HD,W/WASH | 80053D | FRONT DOOR EXPLODED VIEW |
| SCR-F HD,W/WASH | 82053D | REAR DOOR EXPLODED VIEW |
| SCR-F HD,W/WASH | 90050D | BACK DOOR EXPLODED VIEW |
| SCR-MACH,SPL | 80050D | FRONT DOOR LOCK EXPLODED VIEW |
| SCR-MACH,SPL | 82050D | REAR DOOR LOCK EXPLODED VIEW |



