Door & Lock - Hood
Exploded View

| 1. | Hood | 2. | Hood support rod grommet | 3. | Hood secondary latch |
| 4. | Hood support rod | 5. | Bumper rubber | 6. | Radiator core seal |
| 7. | Hood seal | 8. | Hood insulator | 9. | Hood hinge (LH) |
| 10. | Hood hinge (RH) | : Clip |
- Hood Assembly
- Hood Hinge
- Hood Support Rod
Hood Assembly Nissan Pathfinder
Removal and Installation
REMOVAL
Support hood assembly using a suitable tool.
Remove washer tube from hood assembly. Refer to Exploded View.
Remove hood assembly mounting nuts, and then remove hood assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
Adjustment
WITHOUT ROCK CREEK® 
| 1. | Hood | 2. | Front grill | 3. | Front combination lamp |
| 4. | Front fender | 5. | Hood hinge | 6. | Hood bumper rubber |
| 7. | Hood lock |
Check the clearance and the surface height between hood and each part by visual inspection and tactical feel.
If the clearance and the surface height are out of specification, adjust them according to the adjustment procedures.
Unit: mm (in)
| Portion | Standard | Parallelism | |||
|---|---|---|---|---|---|
| Hood – Front grill | A – A | E | Clearance | 6.0 ± 2.5 (0.236 ± 0.098) | < 3.0 [0.118] |
| Hood – Front combination lamp | B – B | F | Clearance | 6.0 ± 2.0 (0.236 ± 0.079) | < 3.9 [0.154] |
| Hood – Front fender | C – C | G | Surface height | 0.5 ± 1.5 (0.020 ± 0.059) | < 2.0 [0.079] |
| H | Clearance | 5.0 ± 2.0 (0.20 ± 0.08) | < 2.0 (0.08) | ||
| Hood – Front fender | D– D | J | Clearance | 5.1 ± 1.0 (0.201 ± 0.039) | < 1.5 [0.059] |
| K | Surface height | 0.0 ± 1.5 (0.00 ± 0.059) | — | ||
WITH ROCK CREEK® 
| 1. | Hood | 2. | Front grill | 3. | Front combination lamp |
| 4. | Front fender | 5. | Hood hinge | 6. | Hood bumper rubber |
| 7. | Hood lock |
Check the clearance and the surface height between hood and each part by visual inspection and tactical feel.
If the clearance and the surface height are out of specification, adjust them according to the adjustment procedures.
Unit: mm (in)
| Portion | Standard | Parallelism | |||
|---|---|---|---|---|---|
| Hood – Front grill | A – A | E | Clearance | 6.0 ± 2.0 (0.236 ± 0.079) | ≤ 3.0 [0.118] |
| Hood – Front combination lamp | B – B | F | Clearance | 6.0 ± 2.0 (0.236 ± 0.079) | < 3.9 [0.154] |
| Hood – Front fender | C – C | G | Surface height | 0.5 ± 1.5 (0.020 ± 0.059) | < 2.0 [0.079] |
| H | Clearance | 5.0 ± 2.0 (0.20 ± 0.08) | < 2.0 (0.08) | ||
| Hood – Front fender | D– D | J | Clearance | 5.1 ± 1.0 (0.201 ± 0.039) | < 1.5 [0.059] |
| K | Surface height | 0.0 ± 1.5 (0.00 ± 0.059) | — | ||
HEIGHT ADJUSTMENT
Loosen the hood lock bolts.
Adjust the surface height of hood to front bumper fascia and front fender according to the specified values by rotating hood bumper rubber.
Temporarily tighten hood lock bolts.
Adjust (A) and (B) as shown to the following value with hood's own weight by dropping it from approximately 200 mm (7.87 in) height.

| 1. | Primary striker | 2. | Primary latch | 3. | Secondary latch |
| 4. | Secondary striker | A. | 20 mm (0.79 in) | B. | 6.8 mm (0.27 in) |
After adjustment, tighten hood hinge nuts and bolts to the specified torque.
CLEARANCE ADJUSTMENT
Loosen hood hinge nuts and bolts.
Loosen the hood lock bolts.
Adjust the hood so the clearance measurements are within specifications.
Tighten the hood hinge nuts and bolts to specified torque.
Tighten the hood lock bolts to specified torque.
Hood Hinge Nissan Pathfinder SUV
Removal and Installation
REMOVAL
Remove hood assembly. Refer to Removal and Installation.
Remove front fender. Refer to Removal and Installation.
Remove hood hinge mounting bolts, and then remove hood hinge.
INSTALLATION
Installation is in the reverse order of removal.
Hood Support Rod Nissan Pathfinder Fifth generation
Removal and Installation
REMOVAL
Support hood assembly with a suitable material to prevent it from falling.
Remove hood support rod from hood support rod grommet.
Disengage hood support rod grommet fixing pawls, and then remove hood support rod grommet from radiator core support.
INSTALLATION
Installation is in the reverse order of removal.