Transmission & Driveline :: Transaxle & Transmission

4006 P06b1-00 Sensor Power Supply a (tcm)

In this manual: Transmission & Driveline :: Transaxle & Transmission
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
103steps
~618min
5/5difficulty
Done 0 of 103
  • P06b1-00 Sensor Power Supply a (tcm)
  • P06b1-00 Sensor Power Supply a (electric Shift)
  • P0702-00 Transmission Control System
  • P0710-00 Transmission Fluid Temperature Sensor a
  • P0711-00 Transmission Fluid Temperature Sensor a
  • P0715-00 Input Speed Sensor a
  • P0729-00 6gr Incorrect Ratio
  • P072f-00 Stuck in Gear 4
  • P073e-00 Unable to Engage Neutral
  • P0742-00 Torque Converter

P06b1-00 Sensor Power Supply a (tcm) Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P06B1 00

SENSOR POWER SUPPLY A

(Sensor Power Supply "A" Circuit Low)
Diagnosis condition Ignition is switched on
Signal —
Threshold The signal voltage deviates from the specified value.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Harness or connector (Sensor power supply circuit is open or shorted.)

  • TCM

FAIL-SAFE

  • Unable driving

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

  • Neutral hold mode is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Ignition switch ON and wait for at least 5 seconds.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK BATTERY CONDITION

Check the battery condition. Refer to Diagnostic Work Sheet.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Charge or replace the battery.

INSPECT WIRING HARNESS

Inspect wiring harness for any damage.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace wiring harness.

INSPECT CONNECTOR TERMINAL

  1. Ignition switch OFF.

  2. Disconnect TCM harness connector and A/T unit harness connector.

  3. Inspect TCM connector and A/T unit connector for signs of water ingress, and pins for damage and/or corrosion.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace damaged parts.

CHECK SENSOR POWER SUPPLY CIRCUIT (PART 1)

Check continuity between TCM harness connector terminal and A/T unit harness connector terminal.

TCMA/T unitContinuity
ConnectorTerminalConnectorTerminal
F15 12 F46 24 Existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness connector.

CHECK SENSOR POWER SUPPLY CIRCUIT (PART 2)

Check continuity between TCM harness connector terminal and ground.

TCM—Continuity
ConnectorTerminal
F15 12 Ground Not existed

Is the inspection result normal?

YES>>

Replace TCM. Refer to Removal and Installation.

NO>>

Repair or replace harness connector.

P06b1-00 Sensor Power Supply a (electric Shift) Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P06B1* 00

SENSOR POWER SUPPLY A

(Sensor Power Supply "A" Circuit Low)
1 Diagnosis condition When the Ignition switch is ON
Signal (terminal) Electric shift sensor signal
Threshold Electric shift sensors No. 1, 3, 5 and 7 are stuck at OFF.
Diagnosis delay time 1.2 seconds
2 Diagnosis condition When the Ignition switch is ON
Signal (terminal) Electric shift sensor signal
Threshold Electric shift sensors No. 2, 4, 6 and 8 are stuck at OFF.
Diagnosis delay time 1.2 seconds
3 Diagnosis condition When the Ignition switch is ON
Signal (terminal) Electric shift sensor signal
Threshold Output voltage of electric shift sensor power supply 1 and 2 are 6 V or more, or 4 V or less.
Diagnosis delay time 1.2 seconds

*: This code is displayed as P0914 on GST.

Shift position judgement table
Select lever positionElectric shift sensor
No. 1No. 2No. 3No. 4No. 5No. 6No. 7No. 8
R ON ON OFF OFF OFF OFF OFF OFF
Nr ON ON ON ON ON OFF OFF OFF
H ON ON ON ON ON ON ON ON
Nd OFF OFF OFF ON ON ON ON ON
D/M OFF OFF OFF OFF OFF OFF ON ON

POSSIBLE CAUSE

  • Harness or connectors (Electric shift sensor circuits are open or shorted.)

  • Electric shift sensor

  • Electric shift control module

FAIL-SAFE

No impact to vehicle behavior

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 60 seconds before conducting the next test.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Ignition switch ON.

  2. Select “Data Monitor” in “SHIFT”.

  3. Select “Shift position judgment”.

  4. Shift the selector lever as follows. (Hold the selector lever at each position for 2 seconds or more.)

    H → Nr → R → Nd → D/M → H

  5. Repeat step 4 five times.

  6. Check DTC.

Is DTC detected?

YES>>

Go to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Go to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK ELECTRIC SHIFT SENSOR INPUT SIGNAL

With CONSULT

  1. Ignition switch ON.

  2. Select “Data Monitor” in “SHIFT”.

  3. Select “Shift sensor 1”, “Shift sensor 2”, “Shift sensor 3”, “Shift sensor 4”, “Shift sensor 5”, “Shift sensor 6”, “Shift sensor 7”, and “Shift sensor 8”.

  4. Operate the selector lever to identify a electric shift sensor of which value does not change.

    Monitor itemConditionValue / Status
    Shift sensor 1 Selector lever is held in H (Home), R, and Nr positions On
    Other than the above Off
    Shift sensor 2 Selector lever is held in H (Home), R, and Nr positions On
    Other than the above Off
    Shift sensor 3 Selector lever is held in H (Home) and Nr positions On
    Other than the above Off
    Shift sensor 4 Selector lever is held in H (Home), Nr, and Nd positions On
    Other than the above Off
    Shift sensor 5 Selector lever is held in H (Home), Nr, and Nd positions On
    Other than the above Off
    Shift sensor 6 Selector lever is held in H (Home) and Nd positions On
    Other than the above Off
    Shift sensor 7 Selector lever is held in H (Home), D/M, and Nd positions On
    Other than the above Off
    Shift sensor 8 Selector lever is held in H (Home), D/M, and Nd positions On
    Other than the above Off

Without CONSULT

  1. Ignition switch ON.

  2. Operate the selector lever.

  3. Check the voltage between the electric shift control module harness connector terminal and ground.

    Electric shift sensor+-Condition

    Voltage

    (Approx.)
    Electric shift control module
    ConnectorTerminal
    1 M36 23 Ground Selector lever is held in H (Home), R, and Nr positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V
    2 26 Selector lever is held in H (Home), R, and Nr positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V
    3 8 Selector lever is held in H (Home) and Nr positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V
    4 11 Selector lever is held inH (Home), Nr, and Nd positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V
    5 24 Selector lever is held in H (Home), Nr, and Nd positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V
    6 27 Selector lever is held in H (Home) and Nd positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V
    7 9 Selector lever is held in H (Home), D/M, and Nd positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V
    8 12 Selector lever is held in H (Home), D/M, and Nd positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V
>>

GO TO 2.

CHECK ELECTRIC SHIFT SELECTOR POWER SUPPLY CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect the electric shift selector harness connector.

  3. Ignition switch ON.

  4. Check the power circuit of the malfunctioning electric shift sensor identified at Step 1.

  5. Check the voltage between electric shift selector harness connector terminal and ground.

    Electric shift sensor+-

    Voltage

    (Approx.)
    Electric shift selector
    ConnectorTerminal
    1, 3, 5, 7 M208 1 Ground 5 V
    2, 4, 6, 8 13

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK HARNESS BETWEEN ELECTRIC SHIFT CONTROL MODULE AND ELECTRIC SHIFT SELECTOR

  1. Ignition switch OFF.

  2. Disconnect the electric shift control module harness connector.

  3. Check the continuity between the electric shift control module harness connector terminal and the electric shift selector harness connector terminal.

    Electric shift sensorElectric shift control moduleElectric shift selectorContinuity
    ConnectorTerminalConnectorTerminal
    1, 3, 5, 7 M36 25 M208 1 Existed
    2, 4, 6, 8 10 13
  4. Check the continuity between the electric shift control module harness connector terminal and ground.

    Electric shift sensorElectric shift control module—Continuity
    ConnectorTerminal
    1, 3, 5, 7 M36 25 Ground Not existed
    2, 4, 6, 8 10

Is the inspection result normal?

YES>>

Replace the electric shift control module. Refer to Removal and Installation.

NO>>

Repair or replace damaged parts.

CHECK ELECTRIC SHIFT SELECTOR GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect the electric shift control module harness connector.

  3. Check the continuity between the electric shift control module harness connector terminal and the electric shift selector harness connector terminal.

    Electric shift sensorElectric shift control moduleElectric shift selectorContinuity
    ConnectorTerminalConnectorTerminal
    1, 3, 5, 7 M36 28 M208 12 Existed
    2, 4, 6, 8 13 24
  4. Check the continuity between the electric shift control module harness connector terminal and ground.

    Electric shift sensorElectric shift control module—Continuity
    ConnectorTerminal
    1, 3, 5, 7 M36 28 Ground Not existed
    2, 4, 6, 8 13

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace damaged parts.

CHECK HARNESS BETWEEN ELECTRIC SHIFT CONTROL MODULE AND ELECTRIC SHIFT SELECTOR

  1. Check the continuity between the electric shift control module harness connector terminal and the electric shift selector harness connector terminal.

    Electric shift sensorElectric shift control moduleElectric shift selectorContinuity
    ConnectorTerminalConnectorTerminal
    1 M36 23 M208 2 Existed
    2 26 14
    3 8 3
    4 11 15
    5 24 4
    6 27 16
    7 9 5
    8 12 17
  2. Check the continuity between the electric shift control module harness connector terminals and ground.

    Electric shift sensorElectric shift control module—Continuity
    ConnectorTerminal
    1 M36 23 Ground Not existed
    2 26
    3 8
    4 11
    5 24
    6 27
    7 9
    8 12

Is the inspection result normal?

YES>>

Replace the electric shift selector. Refer to Removal and Installation.

NO>>

Repair or replace damaged parts.

P0702-00 Transmission Control System Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0702 00

CONTROL SYSTEM ELECTRICAL

(Transmission Control System Electrical)
1 Diagnosis condition Ignition is switched on
Signal —
Threshold When a reset code for low level software or under voltage condition has been stored in the non volatile RAM
Diagnosis delay time 2 seconds or more
2 Diagnosis condition While driving
Signal —
Threshold When a TCM reset occurs during an under voltage condition
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

TCM

FAIL-SAFE

Not changed from normal driving

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Drive the Nissan Pathfinder vehicle at 40 km/h and maintain vehicle speed for 10 seconds or more.

  3. Stop the vehicle.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

REPLACE TCM

Replace TCM. Refer to Removal and Installation.

>>

WORK END

P0710-00 Transmission Fluid Temperature Sensor a Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0710 00

FLUID TEMP SENSOR A

(Transmission Fluid Temperature Sensor "A" Circuit)
1 Diagnosis condition Engine running
Signal A/T fluid temperature sensor signal
Threshold A/T fluid temperature is less than the specified temperature.
Diagnosis delay time 65 seconds or more
2 Diagnosis condition Engine running
Signal A/T fluid temperature sensor signal
Threshold A/T fluid temperature is more than the specified temperature.
Diagnosis delay time 65 seconds or more

POSSIBLE CAUSE

  • Harness or connector (A/T fluid temperature sensor circuit)

  • Sensor unit (A/T fluid temperature sensor and internal harness)

  • TCM

FAIL-SAFE

Not changed from normal driving

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine and wait for at least 70 seconds.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

INSPECT CONNECTOR TERMINAL

  1. Ignition switch OFF.

  2. Disconnect TCM harness connector and A/T unit harness connector.

  3. Inspect TCM connector and A/T unit connector for signs of water ingress, and pins for damage and/or corrosion.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace damaged parts.

CHECK A/T FLUID TEMPERATURE SENSOR CIRCUIT (PART 1)

Check continuity between TCM harness connector terminal and A/T unit harness connector terminal.

TCMA/T unitContinuity
ConnectorTerminalConnectorTerminal
F15 17 F46 26 Existed
30 25

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness connector.

CHECK A/T FLUID TEMPERATURE SENSOR CIRCUIT (PART 2)

Check continuity between TCM harness connector terminal and ground.

TCM—Continuity
ConnectorTerminal
F15 17 Ground Not existed
30

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness connector.

CHECK A/T FLUID TEMPERATURE SENSOR CIRCUIT (PART 3)

  1. Ignition switch ON.

  2. Check voltage between TCM harness connector terminal and ground.

    +-Voltage
    TCM
    ConnectorTerminal
    F15 17 Ground 0 V
    30

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness connector.

CHECK A/T FLUID TEMPERATURE SENSOR

Check the resistance between A/T unit connector terminals.

A/T unitConditionResistance (Approx.)
Terminal
25 26 A/T fluid temperature: 25 °C 2 kΩ

Is the inspection result normal?

YES>>

Replace TCM. Refer to Removal and Installation.

NO>>

Replace sensor unit. Refer to Removal and Installation.

P0711-00 Transmission Fluid Temperature Sensor a Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0711 00

FLUID TEMP SENSOR A

(Transmission Fluid Temperature Sensor "A" Circuit Range/Performance)
1 Diagnosis condition While driving
Signal A/T fluid temperature sensor signal
Threshold

The DTC is detected if any of the following conditions is met:

  • The absolute value of the difference between the oil temperature sensor signal measured by the TCM and the calculated oil temperature is more than the specified value for a calibrated amount of time.

  • The A/T fluid temperature sensor signal is less than the specified value after having first reached another higher calibrated threshold in the same driving cycle.

  • The absolute value of the difference between the current transmission oil temperature and a previous oil temperature stored a calibrated time before is less than the specified value.

Diagnosis delay time 305 seconds or more
2 Diagnosis condition Engine running
Signal A/T fluid temperature sensor signal
Threshold The absolute value of the difference between two consecutive data samples of the measured oil temperature sensor signal is more than the specified value.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • A/T fluid level

  • Harness or connector (A/T fluid temperature sensor circuit)

  • Sensor unit (A/T fluid temperature sensor and internal harness)

  • TCM

FAIL-SAFE

  • Shifting is locked

    • While driving: Keeps the gear position when an abnormality is detected

    • When the Nissan Pathfinder vehicle is stopped: Locks in 4th gear position

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK (PART 1)

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PREPARATION BEFORE WORK (PART 2)

  1. Move the Nissan Pathfinder vehicle to a cool place.

  2. Ignition switch OFF and leave the Nissan Pathfinder vehicle for 12 hours.

>>

GO TO 3.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Drive the Nissan Pathfinder vehicle and maintain the following conditions for 7 minutes or more.

    Engine speed : 430 rpm or more

    Output speed : 250 rpm or more

  3. Stop the Nissan Pathfinder vehicle.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK A/T FLUID

Check A/T fluid level and condition. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>
  1. If A/T fluid is leaking, repair damaged part. Refer to Inspection.

  2. Refill or replace A/T fluid. Refer to Adjustment or Replacement.

INSPECT CONNECTOR TERMINAL

  1. Ignition switch OFF.

  2. Disconnect TCM harness connector and A/T unit harness connector.

  3. Inspect TCM connector and A/T unit connector for signs of water ingress, and pins for damage and/or corrosion.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace damaged parts.

CHECK A/T FLUID TEMPERATURE SENSOR CIRCUIT (PART 1)

Check continuity between TCM harness connector terminal and A/T unit harness connector terminal.

TCMA/T unitContinuity
ConnectorTerminalConnectorTerminal
F15 17 F46 26 Existed
30 25

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness connector.

CHECK A/T FLUID TEMPERATURE SENSOR CIRCUIT (PART 2)

Check continuity between TCM harness connector terminal and ground.

TCM—Continuity
ConnectorTerminal
F15 17 Ground Not existed
30

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness connector.

CHECK A/T FLUID TEMPERATURE SENSOR CIRCUIT (PART 3)

  1. Ignition switch ON.

  2. Check voltage between TCM harness connector terminal and ground.

    +-Voltage
    TCM
    ConnectorTerminal
    F15 17 Ground 0 V
    30

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness connector.

CHECK A/T FLUID TEMPERATURE SENSOR

Check the resistance between A/T unit connector terminals.

A/T unitConditionResistance (Approx.)
Terminal
25 26 A/T fluid temperature: 25 °C 2 kΩ

Is the inspection result normal?

YES>>

Replace TCM. Refer to Removal and Installation.

NO>>

Replace sensor unit. Refer to Removal and Installation.

P0715-00 Input Speed Sensor a Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0715 00

INPUT SPEED SENSOR A

(Input/Turbine Shaft Speed Sensor "A" Circuit)
1 Diagnosis condition
  • While driving

  • Transmission is in fixed gear

Signal Dual speed sensor (Input speed) signal
Threshold If the difference between input speed and output speed converted to input level is more than the specified speed and if the difference between input speed and wheel speed converted to input level is more than the specified speed
Diagnosis delay time 2 seconds or more
2 Diagnosis condition While driving
Signal Dual speed sensor (Input speed) signal
Threshold Transmission input speed is less than the specified speed.
Diagnosis delay time 2 seconds or more
3 Diagnosis condition
  • Engine speed < 100 rpm

  • Shift position: P

Signal Dual speed sensor (Input speed) signal
Threshold Transmission input speed is more than the specified speed.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Transaxle mounting

  • Drive shaft

  • Harness or connector [Dual speed sensor (input speed) circuit]

  • Sensor unit (Dual speed sensor and internal harness)

  • Wheel speed signal

  • TCM

FAIL-SAFE

  • Shifting is locked

    • While driving: Keeps the gear position when an abnormality is detected

    • When the Nissan Pathfinder vehicle is stopped: Locks in 4th gear position

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Drive the Nissan Pathfinder vehicle at 40 km/h for at least 5 seconds.

  3. Stop the vehicle.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

NO-1 >> To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC (ABS)

With CONSULT

  1. Ignition switch ON.

  2. Perform “Self Diagnostic Results” in “ABS”.

Is any DTC detected?

YES>>

Check DTC detected item. Refer to DTC Index.

NO>>

INSPECTION END

CHECK DRIVELINE

Check the driveline for damaged.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace damaged part.

CHECK ENGINE MOUNT AND TRANSAXLE MOUNT

Check the engine mounts and the transaxle mounts damage.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace damaged part.

INSPECT CONNECTOR TERMINAL

  1. Ignition switch OFF.

  2. Disconnect TCM harness connector and A/T unit harness connector.

  3. Inspect TCM connector and A/T unit connector for signs of water ingress, and pins for damage and/or corrosion.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace damaged parts.

CHECK DUAL SPEED SENSOR (INPUT SPEED) CIRCUIT (PART 1)

Check continuity between TCM harness connector terminal and A/T unit harness connector terminal.

TCMA/T unitContinuity
ConnectorTerminalConnectorTerminal
F15 31 F46 23 Existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness connector.

CHECK DUAL SPEED SENSOR (INPUT SPEED) CIRCUIT (PART 2)

Check continuity between TCM harness connector terminal and ground.

TCM—Continuity
ConnectorTerminal
F15 31 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace harness connector.

CHECK DUAL SPEED SENSOR (INPUT SPEED) CIRCUIT (PART 3)

  1. Ignition switch ON.

  2. Check voltage between TCM harness connector terminal and ground.

    +-Voltage
    TCM
    ConnectorTerminal
    F15 31 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace harness connector.

REPLACE SENSOR UNIT

  1. Ignition switch OFF.

  2. Replace sensor unit. Refer to Removal and Installation.

>>

GO TO 9.

PERFORM DTC CONFIRMATION PROCEDURE

Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

Replace TCM. Refer to Removal and Installation.

NO>>

INSPECTION END

P0729-00 6gr Incorrect Ratio Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0729 00

6GR INCORRECT RATIO

(Gear 6 Incorrect Ratio)
Diagnosis condition
  • While driving

  • Shift position: D

  • Transmission gear: 6th

Signal —
Threshold

MThe DTC is detected if any of the following conditions is met:

  • Malfunction symptom counter of the brake C is more than the specified number of times.

  • Malfunction symptom counter of the clutch E is more than the specified number of times.

  • Malfunction symptom counter of the brake C and clutch E is more than the specified number of times.

Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • A/T fluid level

  • Transaxle assembly

FAIL-SAFE

  • Gear is locked in 5th gear

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

With CONSULT

  1. Start the engine.

  2. Select "Data Monitor" in "TRANSMISSION".

  3. Drive the Nissan Pathfinder vehicle for at least 10 seconds under the following conditions.

    Shift position: D

    Transmission gear: 6th

  4. Stop the Nissan Pathfinder vehicle.

  5. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK A/T FLUID

Check A/T fluid level and condition. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>
  1. If A/T fluid is leaking, repair damaged part. Refer to Inspection.

  2. Refill or replace A/T fluid. Refer to Adjustment or Replacement.

CHECK DRIVELINE (PART 1)

Check the driveline for debris around rotating components.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace damaged part.

CHECK DRIVELINE (PART 2)

Check the driveline for excessive wear or backlash.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace damaged part.

CHECK WHEEL AND TIRE

Check the wheels and tires for snow or mud packing and correct balance.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace damaged part.

CHECK ENGINE MOUNT AND TRANSAXLE MOUNT

Check the engine mounts and the transaxle mounts damage.

Is the inspection result normal?

YES>>

Replace transaxle assembly. Refer to Removal and Installation.

NO>>

Repair or replace damaged part.

P072f-00 Stuck in Gear 4 Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P072F 00

STUCK IN GEAR 4

(Stuck in Gear 4)
Diagnosis condition
  • While driving

  • Shift position: D

Signal —
Threshold If the timer to close clutch E is more than the specified value and the measured input speed is within a calibratable range of the output speed multiplied by the gear ratio of the fourth gear for a calibratable amount of time.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • A/T fluid level

  • Transaxle assembly

FAIL-SAFE

  • Drive in 4th gear

  • Engine torque is limited

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Drive the Nissan Pathfinder vehicle for a few minutes under the following conditions.

    Shift position: D position

  3. Stop the Nissan Pathfinder vehicle.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK A/T FLUID

Check A/T fluid level and condition. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>
  1. If A/T fluid is leaking, repair damaged part. Refer to Inspection.

  2. Refill or replace A/T fluid. Refer to Adjustment or Replacement.

REPLACE TRANSAXLE ASSEMBLY

Replace transaxle assembly. Refer to Removal and Installation.

Is the inspection result normal?

>>

WORK END

P073e-00 Unable to Engage Neutral Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P073E 00

UNABLE TO ENGAGE REVERSE

(Unable to Engage Reverse)
Diagnosis condition
  • While driving

  • Shift position: R

Signal —
Threshold Malfunction symptom counter of the clutch A is more than the specified number of times.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • A/T fluid level

  • Transaxle assembly

FAIL-SAFE

  • Shifting is limited (Shifting between the gears of 1 - 2 - 3 - 4 - 5 - 6 - 7 can be performed)

  • Stop/start system is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Depress the brake pedal.

  3. Shift to the R position and wait for at least 5 seconds.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK A/T FLUID

Check A/T fluid level and condition. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>
  1. If A/T fluid is leaking, repair damaged part. Refer to Inspection.

  2. Refill or replace A/T fluid. Refer to Adjustment or Replacement.

REPLACE TRANSAXLE ASSEMBLY

Replace transaxle assembly. Refer to Removal and Installation.

>>

WORK END

P0742-00 Torque Converter Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0742 00

TORQUE CONVERTER

(Torque Converter Clutch Circuit Stuck On)
Diagnosis condition
  • Engine running

  • Shift position: D or R

Signal —
Threshold

The DTC is detected if the following conditions are met:

  • The torque converter clutch slip speed is less than the specified speed.

  • The engine speed is less than the specified speed.

Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • A/T fluid level

  • Torque converter clutch pressure regulator

  • Harness or connector (Torque converter clutch pressure regulator circuit is open or shorted.)

  • Torque converter

  • Transaxle assembly

FAIL-SAFE

Not changed from normal driving

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Depress the brake pedal.

  3. Shift the selector lever to D position and wait for at least 5 seconds. (Shift position: P → D)

  4. Press the P position switch.

  5. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK A/T FLUID

Check A/T fluid level and condition. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>
  1. If A/T fluid is leaking, repair damaged part. Refer to Inspection.

  2. Refill or replace A/T fluid. Refer to Adjustment or Replacement.

INSPECT CONNECTOR TERMINAL

  1. Ignition switch OFF.

  2. Disconnect TCM harness connector and A/T unit harness connector.

  3. Inspect TCM connector and A/T unit connector for signs of water ingress, and pins for damage and/or corrosion.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace damaged parts.

CHECK TORQUE CONVERTER CLUTCH PRESSURE REGULATOR CIRCUIT FOR SHORT TO GROUND (PART 1)

Check continuity between A/T unit connector terminal and ground.

A/T unit—Continuity
Terminal
10 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace sensor unit. Refer to Removal and Installation.

CHECK TORQUE CONVERTER CLUTCH PRESSURE REGULATOR CIRCUIT FOR SHORT TO GROUND (PART 2)

Check continuity between TCM harness connector terminal and ground.

TCM—Continuity
ConnectorTerminal
F15 39 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness connector.

CHECK TORQUE CONVERTER CLUTCH PRESSURE REGULATOR

Check resistance between A/T unit connector terminals.

A/T unit

Resistance

(Approx.)
Terminal
1 10 4.5 - 6 Ω

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Replace sensor unit and control valve. Refer to Removal and Installation.

REPLACE TORQUE CONVERTER

  1. Replace torque converter. Refer to Disassembly.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

REPLACE CONTROL VALVE

  1. Replace control valve. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 8GO TO 8.

NO>>

INSPECTION END

PERFORM DTC CONFIRMATION PROCEDURE

Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

Replace transaxle assembly. Refer to Removal and Installation.

NO>>

INSPECTION END