Transmission & Driveline :: Transaxle & Transmission

4009 P0963-00 Pressure Control Solenoid a

In this manual: Transmission & Driveline :: Transaxle & Transmission
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
74steps
~444min
5/5difficulty
Done 0 of 74
  • P0963-00 Pressure Control Solenoid a
  • P0973-00 Shift Solenoid a
  • P1721-00 Vehicle Speed Signal
  • P1803-49 Control Module Internal Malfunction
  • P1880-00 Clutch Adaptation Mode Monitoring
  • P18a5-00 Automatic Park Function Cancellation
  • P18a8-00 P Position Switch
  • P215c-00 Output Shaft Speed Signal
  • P2765-00 Input Speed Sensor B
  • P277e-00 Clutch a

P0963-00 Pressure Control Solenoid a Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0963 00

PC SOLENOID A

(Pressure Control Solenoid "A" Control Circuit High)
Diagnosis condition Ignition is switched on
Signal Line pressure control pressure regulator drive signal
Threshold

The DTC is detected if any of the following conditions is met:

  • The voltage at the output pin is more than specified value

  • The voltage at the output pin is in the specified range

Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Harness or connector (Line pressure control pressure regulator circuit is open or shorted.)

  • Sensor unit (Internal harness)

  • Line pressure control pressure regulator

  • TCM

FAIL-SAFE

Unable driving

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Drive the Nissan Pathfinder vehicle for a few minutes under the following conditions.

    Shift position: D position

  3. Stop the Nissan Pathfinder vehicle.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

INSPECT CONNECTOR TERMINAL

  1. Ignition switch OFF.

  2. Disconnect TCM harness connector and A/T unit harness connector.

  3. Inspect TCM connector and A/T unit connector for signs of water ingress, and pins for damage and/or corrosion.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace damaged parts.

CHECK LINE PRESSURE CONTROL PRESSURE REGULATOR CIRCUIT FOR SHORT TO GROUND (PART 1)

Check continuity between A/T unit connector terminal and ground.

A/T unit—Continuity
Terminal
9 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace sensor unit. Refer to Removal and Installation.

CHECK LINE PRESSURE CONTROL PRESSURE REGULATOR CIRCUIT FOR SHORT TO BATTERY (PART 1)

  1. Ignition switch ON.

  2. Check voltage between A/T unit connector terminal and ground.

    +-Voltage
    A/T unit
    Terminal
    9 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace sensor unit. Refer to Removal and Installation.

CHECK LINE PRESSURE CONTROL PRESSURE REGULATOR CIRCUIT FOR SHORT TO GROUND (PART 2)

  1. Ignition switch OFF.

  2. Check continuity between TCM harness connector terminal and ground.

    TCM—Continuity
    ConnectorTerminal
    F15 52 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness connector.

CHECK LINE PRESSURE CONTROL PRESSURE REGULATOR CIRCUIT FOR SHORT TO BATTERY (PART 2)

  1. Ignition switch ON.

  2. Check voltage between TCM harness connector terminal and ground.

    +-Voltage
    TCM
    ConnectorTerminal
    F15 52 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness connector.

CHECK LINE PRESSURE CONTROL PRESSURE REGULATOR

Check resistance between A/T unit connector terminals.

A/T unitResistance (Approx.)
Terminal
1 9 4.5 - 6 Ω

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Replace sensor unit and control valve. Refer to Removal and Installation.

PERFORM DTC CONFIRMATION PROCEDURE

Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

Replace TCM. Refer to Removal and Installation.

NO>>

INSPECTION END

P0973-00 Shift Solenoid a Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0973 00

SHIFT SOLENOID A

(Shift Solenoid "A" Control Circuit Low)
Diagnosis condition Ignition is switched on
Signal Dog clutch A solenoid valve drive signal
Threshold The voltage at the output pin is less than specified value.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Harness or connector (Dog clutch A solenoid valve circuit is shorted.)

  • Sensor unit (Internal harness)

  • Dog clutch A solenoid valve

  • TCM

FAIL-SAFE

  • Unable driving

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

  • Neutral hold mode is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Drive the Nissan Pathfinder vehicle for a few minutes under the following conditions.

    Shift position: D position

  3. Stop the Nissan Pathfinder vehicle.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

INSPECT CONNECTOR TERMINAL

  1. Ignition switch OFF.

  2. Disconnect TCM harness connector and A/T unit harness connector.

  3. Inspect TCM connector and A/T unit connector for signs of water ingress, and pins for damage and/or corrosion.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace damaged parts.

CHECK DOG CLUTCH A SOLENOID VALVE CIRCUIT FOR SHORT TO GROUND (PART 1)

Check continuity between A/T unit connector terminal and ground.

A/T unit—Continuity
Terminal
2 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace sensor unit. Refer to Removal and Installation.

CHECK DOG CLUTCH A SOLENOID VALVE CIRCUIT FOR SHORT TO GROUND (PART 2)

Check continuity between TCM harness connector terminal and ground.

TCM—Continuity
ConnectorTerminal
F15 38 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness connector.

CHECK DOG CLUTCH A SOLENOID VALVE

Check resistance between A/T unit connector terminals.

A/T unitResistance (Approx.)
Terminal
1 2 9 - 13 Ω

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace sensor unit and control valve. Refer to Removal and Installation.

PERFORM DTC CONFIRMATION PROCEDURE

Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

Replace TCM. Refer to Removal and Installation.

NO>>

INSPECTION END

P1721-00 Vehicle Speed Signal Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1721 00

Nissan Pathfinder Vehicle SPEED SIGNAL

(Vehicle Speed Signal)
1 Diagnosis condition Ignition is switched on
Signal Front LH wheel speed signal
Threshold Front LH wheel speed signal indicates an abnormal value
Diagnosis delay time 2 seconds or more
2 Diagnosis condition Ignition is switched on
Signal Front RH wheel speed signal
Threshold Front RH wheel speed signal indicates an abnormal value
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Front LH wheel speed signal

  • Front RH wheel speed signal

FAIL-SAFE

Not changed from normal driving

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Ignition switch ON and wait for at least 5 seconds.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC (ABS)

With CONSULT

  1. Ignition switch ON.

  2. Perform “Self Diagnostic Results” in “ABS”.

Is any DTC detected?

YES>>

Check DTC detected item. Refer to DTC Index.

NO>>

INSPECTION END

P1803-49 Control Module Internal Malfunction Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1803 49

CONTROL MODULE INTERNAL MALFUNCTION

(Control Module Internal Malfunition)
Diagnosis condition When the Ignition switch is ON
Signal —
Threshold A malfunction is detected in the electric shift control module
Diagnosis delay time —

POSSIBLE CAUSE

Electric shift control module

FAIL-SAFE

  • Shifting operation is prohibited

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

  • Engine torque is limited

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 60 seconds before conducting the next test.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignitino switch ON and wait for 2 seconds or more.

  2. Check DTC.

Is DTC detected?

YES>>

Go to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Go to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

REPLACE ELECTRIC SHIFT CONTROL MODULE

Replace the electric shift control module. Refer to Removal and Installation.

>>

END

P1880-00 Clutch Adaptation Mode Monitoring Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1880 00

CLUTCH ADAPTATION MODE MONI

(Clutch Adaptation Mode Monitoring)
Diagnosis condition Ignition is switched on
Signal —
Threshold A/T clutch touch point learning is not completed
Diagnosis delay time —

POSSIBLE CAUSE

A/T clutch touch point learning is not completed

FAIL-SAFE

Not changed from normal driving

DTC CONFIRMATION PROCEDURE

If this DTC is detected, perform diagnosis procedure. Diagnosis Procedure.

Diagnosis Procedure

CHECK DTC (TRANSMISSION)

With CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Results” in “TRANSMISSION”.

P1880-00 is "PAST">>

GO TO 2.

P1880-00 is "CRNT">>

GO TO 3.

ERASE DTC

With CONSULT

Erase DTC of "TRANSMISSION".

>>

WORK END

PERFORM A/T CLUTCH TOUCH POINT LEARNING

With CONSULT

  1. Erase DTC of "TRANSMISSION".

  2. Perform A/T clutch touch point learning. Refer to Description.

>>

WORK END

P18a5-00 Automatic Park Function Cancellation Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P18A5 00

AUTO PARK FUNCTION CANCEL

(Automatic park function cancellation)
Diagnosis condition Ignition is switched on
Signal —
Threshold When the automatic park function is canceled
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

—

FAIL-SAFE

Not changed from normal driving

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Ignition switch ON.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

ACTIVATE AUTOMATIC P POSITION FUNCTION

With CONSULT

  1. Ignition switch ON.

  2. Select "CANCEL AUTOMATIC PARK FUNCTION" in "Work Support" of "TRANSMISSION".

  3. Change the status of "CANCEL AUTOMATIC PARK FUNCTION" from "On" to "Off", and then touch "End".

Without CONSULT

  1. Ignition switch ON and wait for at least 5 seconds.

  2. Ignition switch OFF and wait for at least 15 seconds.

  3. Repeat step 1 to 2 one hundred times. (Electric shift warning lamp stops blinking)

>>

WORK END

P18a8-00 P Position Switch Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P18A8 00

P POSITION SWITCH

(P Position Switch Error)
1 Diagnosis condition When the Ignition switch is ON
Signal (terminal) P position switch No. 1 and No. 2 signal
Threshold P position switches No. 1 and No. 2 are stuck at ON or OFF.
Diagnosis delay time —
2 Diagnosis condition When the Ignition switch is ON
Signal (terminal) P position switch No. 1 and No. 2 signal
Threshold P position switch No. 1 is stuck at ON and P position switch No. 2 is stuck at OFF.
Diagnosis delay time —
P position switchP position switch
No. 1No. 2
Press ON OFF
No press OFF ON

POSSIBLE CAUSE

  • Harness or connectors (P position switch No. 1 and No. 2 circuits are open or shorted.)

  • P position switch

FAIL-SAFE

Pushing the P position switch does not switch to the P position

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 60 seconds before conducting the next test.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE (PART 1)

With CONSULT

  1. Ignition switch ON.

  2. Press the P position switch and wait for 5 seconds or more. (Be sure to press and hold the P position switch for 1 seconds or more.)

  3. Repeat step 2 four times.

  4. Check DTC.

Is DTC detected?

YES>>

Go to Diagnosis Procedure.

NO>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE (PART 2)

With CONSULT

  1. Release the P position switch and wait for 5 minutes or more.

  2. Check DTC.

Is DTC detected?

YES>>

Go to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Go to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK HARNESS BETWEEN ELECTRIC SHIFT CONTROL MODULE AND ELECTRIC SHIFT SELECTOR

  1. Ignition switch OFF.

  2. Disconnect the electric shift control module harness connector.

  3. Disconnect the electric shift selector harness connector.

  4. Check the continuity between electric shift control module harness connector terminals and electric shift selector harness connector terminals.

    Electric shift control moduleElectric shift selectorContinuity
    ConnectorTerminalConnectorTerminal
    M36 20 M208 6 Existed
    6 18

  5. Check the continuity between electric shift control module harness connector terminals and ground.

    Electric shift control module—Continuity
    ConnectorTerminal
    M36 20 Ground Not existed
    6

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace damaged parts.

CHECK P POSITION SWITCH

Check the P position switch. Refer to Component Inspection (P Position Switch).

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace the electric shift selector. Refer to Removal and Installation.

Component Inspection (P Position Switch)

CHECK P POSITION SWITCH

  1. Disconnect the electric shift selector connectors.

  2. Check the continuity between electric shift selector connector terminals.

    Electric shift selectorConditionContinuity
    P position switchTerminal
    No. 1 1 6 When P position switch is pressed Existed
    When P position switch is released Not existed
    No. 2 13 18 When P position switch is pressed Not existed
    When P position switch is released Existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace the electric shift selector due to malfunction in the P position switch. Refer to Removal and Installation.

P215c-00 Output Shaft Speed Signal Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P215C 00

OUTPUT SHAFT SPD - WHEEL SPD

(Output Shaft Speed - Wheel Speed Correlation)
Diagnosis condition Ignition is switched on
Signal —
Threshold The difference between output speed and wheel speed converted to output level is more than specified value while the transmission is not in fixed gear.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Tire (Size is different from an original)

  • TCM

FAIL-SAFE

  • Shifting is locked

    • While driving: Keeps the gear position when an abnormality is detected

    • When the Nissan Pathfinder vehicle is stopped: Locks in 4th gear position

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Drive the Nissan Pathfinder vehicle for a few minutes under the following conditions.

    Shift position: D position

  3. Stop the Nissan Pathfinder vehicle.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK FOR TIRE SIZE

Check the tires are the original size of the Nissan Pathfinder vehicle.

Is the inspection result normal?

YES>>

Replace TCM. Refer to Removal and Installation.

NO>>

Replace with the correct size tire.

P2765-00 Input Speed Sensor B Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P2765 00

INPUT SPEED SENSOR B

(Input/Turbine Shaft Speed Sensor "B" Circuit)
Diagnosis condition
  • While driving

  • Shift position: Other than P and N

Signal —
Threshold Positive torque intervention is more than the specified value and the absolute value of the difference between the current input speed gradient and the current output speed gradient multiplied by the current gear ratio is less than the specified value
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

TCM

FAIL-SAFE

  • Shifting is locked

    • While driving: Keeps the gear position when an abnormality is detected

    • When the Nissan Pathfinder vehicle is stopped: Locks in 4th gear position

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Drive the Nissan Pathfinder vehicle for a few minutes under the following conditions.

    Shift position: D position

  3. Stop the Nissan Pathfinder vehicle.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

REPLACE TCM

Replace TCM. Refer to Removal and Installation.

>>

WORK END

P277e-00 Clutch a Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P277E 00

CLUTCH A GEAR DISENGAGEMENT

(Clutch "A" Unexpected Mechanical Gear Disengagement)
Diagnosis condition Ignition is switched on
Signal —
Threshold During function with engine off and no pump pressure available, the dog clutch A moves unintended from the position engaged into direction of disengaged.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Dog clutch A

  • Dog clutch A solenoid valve

  • Control valve

FAIL-SAFE

Unable driving

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION (PART 1)

  1. Start the engine.

  2. Drive the Nissan Pathfinder vehicle for a few minutes under the following conditions.

    Shift position: D position

  3. Stop the Nissan Pathfinder vehicle.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO>>

GO TO 3.

PERFORM DTC DETECTION (PART 2)

  1. Start the engine.

  2. Maintain stop/start system operation state for 10 seconds or more. Refer to System Description.

  3. Restart the engine.

  4. Repeat step 2 to 3 3 times.

  5. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC (TRANSMISSION)

With CONSULT

  1. Ignition switch ON.

  2. Perform “Self Diagnostic Results” in “TRANSMISSION”.

Is DTC other than P277E detected?

YES>>

Check DTC detected item. Refer to DTC Index.

NO>>

GO TO 2.

CHECK A/T FLUID

  1. Ignition switch OFF.

  2. Check A/T fluid level and condition. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>
  1. If A/T fluid is leaking, repair damaged part. Refer to Inspection.

  2. Refill or replace A/T fluid. Refer to Adjustment or Replacement.

REPLACE TRANSAXLE ASSEMBLY

Removal transaxle assembly. Refer to Removal and Installation.

>>

WORK END