Transmission & Driveline :: Transaxle & Transmission

4008 P07ec-00 T/m Range Multi-Function Select

In this manual: Transmission & Driveline :: Transaxle & Transmission
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
93steps
~558min
5/5difficulty
Done 0 of 93
  • P07ec-00 T/m Range Multi-Function Select
  • P0805-00 Clutch Position Sensor a
  • P0826-00 Up/down Shift Switch
  • P0850-00 Park Neutral Switch (tcm)
  • P0850-00 Park Neutral Switch (electric Shift)
  • P0851-00 Park Neutral Switch
  • P0860-00 Gear Shift Control Module a
  • P0881-00 Tcm Power Input Signal
  • P0893-00 Multiple Gears Engaged
  • P0914-00 Gear Shift Position

P07ec-00 T/m Range Multi-Function Select Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P07EC 00

T/M RANGE SELECT

(Transmission Range Multi-Function Select Circuit)
Diagnosis condition When the ignition switch is ON
Signal Electric shift sensor signal
Threshold One of the electric shift sensors No. 1 to No. 8 is stuck at ON or OFF.
Diagnosis delay time —
Shift position judgement table
Selector lever positionElectric shift sensor
No. 1No. 2No. 3No. 4No. 5No. 6No. 7No. 8
R ON ON OFF OFF OFF OFF OFF OFF
Nr ON ON ON ON ON OFF OFF OFF
H ON ON ON ON ON ON ON ON
Nd OFF OFF OFF ON ON ON ON ON
D/M OFF OFF OFF OFF OFF OFF ON ON

POSSIBLE CAUSE

  • Electric shift sensor

  • Harness or connectors (Electric shift sensor circuit is open or shorted.)

FAIL-SAFE

Determination time of the shift selector position becomes long (1 second or more)

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 60 seconds before conducting the next test.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Ignition switch ON.

  2. Select “Data Monitor” in “SHIFT”.

  3. Select “Shift position judgment”.

  4. Shift the selector lever as follows. (Hold the selector lever at each position for 2 seconds or more.)

    H → Nr → R → Nd → D/M → H

  5. Repeat step 4 five times.

  6. Check DTC.

Is DTC detected?

YES>>

Go to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Go to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK ELECTRIC SHIFT SENSOR INPUT SIGNAL

With CONSULT

  1. Ignition switch ON.

  2. Select “Data Monitor” in “SHIFT”.

  3. Select “Shift sensor 1”, “Shift sensor 2”, “Shift sensor 3”, “Shift sensor 4”, “Shift sensor 5”, “Shift sensor 6”, “Shift sensor 7”, and “Shift sensor 8”.

  4. Operate the selector lever to identify a electric shift sensor of which value does not change.

    Monitor itemConditionValue / Status
    Shift sensor 1 Selector lever is held in H (Home), R, and Nr positions On
    Other than the above Off
    Shift sensor 2 Selector lever is held in H (Home), R, and Nr positions On
    Other than the above Off
    Shift sensor 3 Selector lever is held in H (Home) and Nr positions On
    Other than the above Off
    Shift sensor 4 Selector lever is held in H (Home), Nr, and Nd positions On
    Other than the above Off
    Shift sensor 5 Selector lever is held in H (Home), Nr, and Nd positions On
    Other than the above Off
    Shift sensor 6 Selector lever is held in H (Home) and Nd positions On
    Other than the above Off
    Shift sensor 7 Selector lever is held in H (Home), D/M, and Nd positions On
    Other than the above Off
    Shift sensor 8 Selector lever is held in H (Home), D/M, and Nd positions On
    Other than the above Off

Without CONSULT

  1. Ignition switch ON.

  2. Operate the selector lever.

  3. Check the voltage between the electric shift control module harness connector terminal and ground.

    Electric shift sensor+−Condition

    Voltage

    (Approx.)
    Electric shift control module
    ConnectorTerminal
    1 M36 23 Ground Selector lever is held in H (Home), R, and Nr positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V
    2 26 Selector lever is held in H (Home), R, and Nr positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V
    3 8 Selector lever is held in H (Home) and Nr positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V
    4 11 Selector lever is held in H (Home), Nr, and Nd positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V
    5 24 Selector lever is held in H (Home), Nr, and Nd positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V
    6 27 Selector lever is held in H (Home) and Nd positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V
    7 9 Selector lever is held in H (Home), D/M, and Nd positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V
    8 12 Selector lever is held in H (Home), D/M, and Nd positions 1.15 - 2.05 V
    Other than the above 2.75 - 3.15 V

Is the inspection results normal?

YES>>

INSPECTION END

NO>>

GO TO 2.

CHECK HARNESS BETWEEN ELECTRIC SHIFT CONTROL MODULE AND ELECTRIC SHIFT SELECTOR

  1. Ignition switch OFF.

  2. Disconnect the electric shift control module harness connector.

  3. Disconnect the electric shift selector harness connector.

  4. Check the continuity between the electric shift control module harness connector terminal and the electric shift selector harness connector terminal.

    Electric shift sensorElectric shift control moduleElectric shift selectorContinuity
    ConnectorTerminalConnectorTerminal
    1 M36 23 M208 2 Existed
    2 26 14
    3 8 3
    4 11 15
    5 24 4
    6 27 16
    7 9 5
    8 12 17
  5. Check the continuity between the electric shift control module harness connector terminals and ground.

    Electric shift sensorElectric shift control module—Continuity
    Connectorterminal
    1 M36 23 Ground Not existed
    2 26
    3 8
    4 11
    5 24
    6 27
    7 9
    8 12

Is the inspection result normal?

YES>>

Replace the electric shift selector. Refer to Removal and Installation.

NO>>

Repair or replace damaged parts.

P0805-00 Clutch Position Sensor a Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0805 00

CLUTCH POSITION SENSOR A

(Clutch Position Sensor "A" Circuit)
1 Diagnosis condition Ignition is switched on
Signal Dog clutch A position sensor signal
Threshold

The DTC is detected if any of the following conditions is met:

  • Dog clutch A position sensor detects that the dog clutch is disengaged of position when the gear is R, 8th, or 9th

  • Dog clutch A position sensor detects that the dog clutch is engaged of position when the gear is 1st, 2nd, 3rd, 4th, 5th, 6th or 7th

Diagnosis delay time 2 seconds or more
2 Diagnosis condition Engine running
Signal Dog clutch A position sensor signal
Threshold Dog clutch A position signal is either much more engaged than the taught in and adapted engaged position or much more disengaged than the taught in and adapted disengaged position.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Harness or connector (Dog clutch A position sensor circuit is open or shorted.)

  • Dog clutch A position sensor

FAIL-SAFE

Stop/start system is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Depress the brake pedal.

  3. Shift to the D position and wait for at least 2 seconds.

  4. Shift to the N position and wait for at least 2 seconds.

  5. Repeat steps 3 to 4 30 times.

  6. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

INSPECT CONNECTOR TERMINAL

  1. Ignition switch OFF.

  2. Disconnect TCM harness connector and A/T unit harness connector.

  3. Inspect TCM connector and A/T unit connector for signs of water ingress, and pins for damage and/or corrosion.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace damaged parts.

CHECK DOG CLUTCH A POSITION SENSOR CIRCUIT FOR OPEN

Check continuity between TCM harness connector terminal and A/T unit harness connector terminal.

TCMA/T unitContinuity
ConnectorTerminalConnectorTerminal
F15 26 F46 13 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness connector.

CHECK DOG CLUTCH A POSITION SENSOR CIRCUIT FOR SHORT TO GROUND

Check continuity between TCM harness connector terminal and ground.

TCM—Continuity
ConnectorTerminal
F15 26 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness connector.

CHECK DOG CLUTCH A POSITION SENSOR CIRCUIT FOR SHORT TO BATTERY

  1. Ignition switch ON.

  2. Check voltage between TCM harness connector terminal and ground.

    +-Voltage
    TCM
    ConnectorTerminal
    F15 26 Ground 0 V

Is the inspection result normal?

YES>>

Replace dog clutch A position sensor. Refer to Removal and Installation.

NO>>

Repair or replace harness connector.

P0826-00 Up/down Shift Switch Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0826 00

UP/DOWN SHIFT SWITCH

(Up and Down Shift Switch Circuit)
Diagnosis condition Ignition is switched on
Signal Paddle shifter signal
Threshold Paddle shifter signal is stuck in the ON state
Diagnosis delay time 60 seconds or more

POSSIBLE CAUSE

  • Harness or connector (Paddle shifter circuit is shorted.)

  • Paddle shifter

  • Spiral cable

FAIL-SAFE

Manual mode is prohibited

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Ignition switch ON and wait for at least 60 seconds.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK PADDLE SHIFTER (SHIFT UP SWITCH) CIRCUIT FOR SHORT TO GROUND (PART 1)

  1. Ignition switch OFF.

  2. Disconnect BCM harness connector and combination switch (spiral cable) harness connector M30.

  3. Check continuity between combination meter (spiral cable) harness connector terminal and ground.

    Combination switch (spiral cable)—Continuity
    ConnectorTerminal
    M30 4 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace harness connector.

CHECK PADDLE SHIFTER (SHIFT DOWN SWITCH) CIRCUIT FOR SHORT TO GROUND (PART 1)

Check continuity between combination meter (spiral cable) harness connector terminal and ground.

Combination switch (spiral cable)—Continuity
ConnectorTerminal
M30 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness connector.

CHECK PADDLE SHIFTER (SHIFT UP SWITCH) CIRCUIT FOR SHORT TO GROUND (PART 2)

  1. Disconnect BCM harness connector and combination switch (spiral cable) harness connector M149.

  2. Check continuity between combination switch (spiral cable) harness connector terminal and ground.

    Combination switch (spiral cable)—Continuity
    ConnectorTerminal
    M149 33 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness connector.

CHECK PADDLE SHIFTER (SHIFT DOWN SWITCH) CIRCUIT FOR SHORT TO GROUND (PART 2)

Check continuity between combination switch (spiral cable) harness connector terminal and ground.

Combination switch (spiral cable)—Continuity
ConnectorTerminal
M149 32 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness connector.

CHECK PADDLE SHIFTER (SHIFT UP SWITCH)

Check continuity between combination switch (spiral cable) harness connector terminals.

Combination switch (spiral cable)ConditionContinuity
ConnectorTerminal
M149 33 31 Shift up switch: ON Existed
Shift up switch: OFF Not existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Replace paddle shifter (shift up switch). Refer to Removal and Installation.

CHECK PADDLE SHIFTER (SHIFT DOWN SWITCH)

Check continuity between combination switch (spiral cable) harness connector terminals.

Combination switch (spiral cable)ConditionContinuity
ConnectorTerminal
M149 32 31 Shift down switch: ON Existed
Shift down switch: OFF Not existed

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Replace paddle shifter (shift down switch). Refer to Removal and Installation.

CHECK PADDLE SHIFTER CIRCUIT FOR SHORT

Check continuity between combination switch (spiral cable) connector terminals.

Combination switch (spiral cable)Continuity
ConnectorTerminal
M149 32 31 Not existed
33

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Replace spiral cable. Refer to Removal and Installation.

P0850-00 Park Neutral Switch (tcm) Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0850 00

PARK/NEUTRAL SWITCH

(Park/Neutral Switch Input Circuit)
Diagnosis condition Ignition is switched on
Signal Park position sensor signal
Threshold

The DTC is detected if any of the following conditions is met:

  • The intermediate position of the parking lock not left in a predefined time

  • An undefined combination of the sensor signals is detected.

Diagnosis delay time 10 seconds or more

POSSIBLE CAUSE

  • Harness or connector (Park position sensor circuit)

  • Sensor unit (Park position sensor and internal harness)

FAIL-SAFE

  • Shift shock occurs (System oil pressure is maximized)

  • Stop/start system is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Depress the brake pedal.

  3. Shift the selector lever to D position and wait for at least 10 seconds. (Shift position: P → D)

  4. Press the P position switch and wait for 10 seconds. (Shift position: D → P)

  5. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK PARKING POSITION SENSOR

  1. Check the park position sensor mounting. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK PARK POSITION SENSOR (P) CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Disconnect TCM connector and A/T unit connector.

  3. Check continuity between TCM harness connector terminal and A/T unit harness connector terminal.

    TCMA/T unitContinuity
    ConnectorTerminalConnectorTerminal
    F15 13 F46 19 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness connector.

CHECK PARK POSITION SENSOR (P) CIRCUIT FOR SHORT TO GROUND

Check continuity between TCM harness connector terminal and ground.

TCM—Continuity
ConnectorTerminal
F15 13 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness connector.

CHECK PARK POSITION SENSOR (P) CIRCUIT FOR SHORT TO BATTERY

  1. Ignition switch ON.

  2. Check voltage between TCM harness connector terminal and ground.

    +-Voltage
    TCM
    ConnectorTerminal
    F15 13 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness connector.

CHECK PARK POSITION SENSOR (NOT P) CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Check continuity between TCM harness connector terminal and A/T unit harness connector terminal.

    TCMA/T unitContinuity
    ConnectorTerminalConnectorTerminal
    F15 15 F46 18 Existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness connector.

CHECK PARK POSITION SENSOR (NOT P) CIRCUIT FOR SHORT TO GROUND

Check continuity between TCM harness connector terminal and ground.

TCM—Continuity
ConnectorTerminal
F15 15 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace harness connector.

CHECK PARK POSITION SENSOR (NOT P) CIRCUIT FOR SHORT TO BATTERY

  1. Ignition switch ON.

  2. Check voltage between TCM harness connector terminal and ground.

    TCM-Voltage
    ConnectorTerminal
    F15 15 Ground 0 V

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace harness connector.

CHECK PARK POSITION SENSOR GROUND CIRCUIT FOR OPEN

  1. Ignition switch OFF.

  2. Check continuity between TCM harness connector terminal and A/T unit harness connector terminal.

    TCMA/T unitContinuity
    ConnectorTerminalConnectorTerminal
    F15 8 F46 17 Existed

Is the inspection result normal?

YES>>

Replace TCM. Refer to Removal and Installation.

NO>>

Repair or replace harness connector.

P0850-00 Park Neutral Switch (electric Shift) Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0850 00

PARK/NEUTRAL SWITCH

(Park/Neutral Switch Input Circuit)
Diagnosis condition Ignition switch: ON
Signal P position switch signal
Threshold

The input voltage is one of the following in one of P position switches No.1 and No.2.

  • 0.65 V ≦ input voltage ≦ 1.00 V

  • 2.20 V < input voltage < 2.60 V

  • 3.40 V ≦ input voltage ≦ 4.35 V

Diagnosis delay time —

POSSIBLE CAUSE

  • Electric shift selector (P position switch)

  • Electric shift control module

  • Harness or connectors (P position switch circuit is open or shorted.)

FAIL-SAFE

No impact to vehicle behavior

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 60 seconds before conducting the next test.

>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Ignition switch ON and wait for at least 5 seconds.

  2. Press the P position switch and hold for at least 5 seconds.

  3. Check DTC.

Is DTC detected?

YES>>

Go to Diagnosis Procedure .

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident .

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK HARNESS BETWEEN ELECTRIC SHIFT CONTROL MODULE AND ELECTRIC SHIFT SELECTOR

  1. Ignition switch OFF.

  2. Disconnect the electric shift selector harness connector.

  3. Disconnect the electric shift control module harness connector.

  4. Check the resistance between the electric shift control module harness connector terminal and the electric shift selector harness connector terminal.

    P position switchElectric shift control moduleElectric shift selector

    Resistance

    (Approx.)
    ConnectorTerminalConnectorTerminal
    Switch 1 M36 20 M208 6 1 Ω or less
    Switch 2 6 18

Is the inspection results normal?

YES>>

GO TO 2 .

NO>>

Repair or replace damaged parts.

REPLACE ELECTRIC SHIFT SELECTOR

  1. Replace the electric shift selector. Refer to Removal and Installation .

  2. Connect all of disconnected connectors.

  3. Perform DTC confirmation procedure. Refer to DTC Description .

Is DTC detected?

YES>>

Replace the electric shift control module. Refer to Removal and Installation .

NO>>

INSPECTION END

P0851-00 Park Neutral Switch Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0851 00

PARK/NEUTRAL SWITCH

(Park/Neutral Switch Input Circuit Low)
Diagnosis condition Ignition switch: ON
Signal P position switch signal
Threshold The input voltage is less than 0.55 V in one of P position switches No.1 and No.2.
Diagnosis delay time —

POSSIBLE CAUSE

  • Electric shift selector (P position switch)

  • Electric shift control module

  • Harness or connectors (P position switch circuit is shorted to ground.)

FAIL-SAFE

No impact to vehicle behavior

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF and wait at least 60 seconds before conducting the next test.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Ignition switch ON and wait for at least 5 seconds.

  2. Press the P position switch and hold for at least 5 seconds.

  3. Check DTC.

Is DTC detected?

YES>>

Go to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK ELECTRIC SHIFT SELECTOR INPUT VOLTAGE

Check the voltage between electric shift selector harness connector terminal and ground.

+–Condition

Voltage

(Approx.)
Electric shift selector
ConnectorTerminal
M208 1 Ground Ignition switch is ON 5 V
13

Is the inspection results normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK HARNESS BETWEEN ELECTRIC SHIFT CONTROL MODULE AND ELECTRIC SHIFT SELECTOR (PART 1)

  1. Ignition switch OFF.

  2. Disconnect the electric shift selector harness connector.

  3. Disconnect the electric shift control module harness connector.

  4. Check the continuity between the electric shift control module harness connector terminal and the electric shift selector harness connector terminal.

    Electric shift control moduleElectric shift selectorContinuity
    ConnectorTerminalConnectorTerminal
    M36 25 M208 1 Existed
    10 13
  5. Check the continuity between the electric shift control module harness connector terminal and ground.

    Electric shift control module—Continuity
    ConnectorTerminal
    M36 25 Ground Not existed
    10

Is the inspection results normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace damaged parts.

CHECK HARNESS BETWEEN ELECTRIC SHIFT CONTROL MODULE AND ELECTRIC SHIFT SELECTOR (PART 2)

  1. Ignition switch OFF.

  2. Disconnect the electric shift selector harness connector.

  3. Disconnect the electric shift control module harness connector.

  4. Check the continuity between the electric shift control module harness connector terminal and the electric shift selector harness connector terminal.

    P position switchElectric shift control moduleElectric shift selectorContinuity
    ConnectorTerminalConnectorTerminal
    Switch 1 M36 20 M208 6 Existed
    Switch 2 6 18
  5. Check the continuity between the electric shift control module harness connector terminal and ground.

    P position switchElectric shift control module―Continuity
    ConnectorTerminal
    Switch 1 M36 20 Ground Not existed
    Switch 2 6
  6. Check the continuity between the electric shift control module harness connector terminals.

    P position switchElectric shift control moduleElectric shift control moduleContinuity
    ConnectorTerminalConnectorTerminal
    Switch 1 M36 20 M36 Except 20 Not existed
    Switch 2 6 Except 6

Is the inspection results normal?

YES>>

GO TO 4.

NO>>

Repair or replace damaged parts.

REPLACE ELECTRIC SHIFT SELECTOR

  1. Replace the electric shift selector. Refer to Removal and Installation.

  2. Connect all of disconnected connectors.

  3. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

Replace the electric shift control module. Refer to Removal and Installation.

NO>>

INSPECTION END

P0860-00 Gear Shift Control Module a Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0860 00

GEAR SHIFT CONTROL MODULE A

(Gear Shift Control Module "A" Communication Circuit)
Diagnosis condition Ignition is switched on
Signal —
Threshold

The DTC is detected if any of the following conditions is met:

  • Communication interrupted two times in a row

  • Incorrect message format received

  • The readback of registers (of the current regulator) returns no data or Implausible data

  • Alive check error

Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

TCM

FAIL-SAFE

  • Unable driving

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

  • Neutral hold mode is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. The ignition switch is ON and wait for at least 5 seconds.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

REPLACE TCM

Replace TCM. Refer to Removal and Installation.

YES>>

WORK END

P0881-00 Tcm Power Input Signal Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0881 00

CONT MODULE POWER INPUT SIG

(TCM Power Input Signal Range/Performance)
Diagnosis condition Ignition is switched on
Signal —
Threshold The hardwired ignition signal of TCM is not equal to the ignition signal via CAN communication.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

Ignition switch signal (via CAN communication)

FAIL-SAFE

Unable driving

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Ignition switch ON and wait for at least 5 seconds.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC (IPDM E/R)

With CONSULT

  1. Ignition switch ON.

  2. Perform “Self Diagnostic Results” in “IPDM E/R”.

Is any DTC detected?

YES>>

Check DTC detected item. Refer to DTC Index.

NO>>

INSPECTION END

P0893-00 Multiple Gears Engaged Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0893 00

MULTIPLE GEARS ENGAGED

(Multiple Gears Engaged)
Diagnosis condition While driving
Signal —
Threshold The output speed gradient is more than the specified value.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • TCM

  • Transaxle assembly

FAIL-SAFE

Unable driving

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Drive the Nissan Pathfinder vehicle for a few minutes under the following conditions.

    Shift position: D position

  3. Stop the Nissan Pathfinder vehicle.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

REPLACE TCM

Replace TCM. Refer to Removal and Installation.

YES>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

Perform DTC confirmation procedure. Refer to DTC Description.

Is any DTC detected?

YES>>

Replace transaxle assembly. Refer to Removal and Installation.

NO>>

INSPECTION END

P0914-00 Gear Shift Position Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0914 00

Gear shift position

(Gear Shift Position Circuit)
Diagnosis condition Ignition is switched ON
Signal —
Threshold TCM receives a specific malfunction signal from the electric shift control module.
Diagnosis delay time —

POSSIBLE CAUSE

Electric shift control system

FAIL-SAFE

Not changed from normal driving

DTC Confirmation Procedure

CHECK DTC OF ELECTRIC SHIFT CONTROL MODULE

With CONSULT

Perform “Self Diagnostic Results” in “SHIFT”.

Is any DTC detected?

YES>>

Perform diagnosis of detected DTC. Refer to Trouble Diagnosis Flow Chart.

NO>>

GO TO 2.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 3.

CHECK DTC DETECTION

  1. Start the engine and wait for at least 5 seconds.

  2. Check the DTC.

Is DTC detected?

YES>>

Go to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC OF ELECTRIC SHIFT CONTROL MODULE

With CONSULT

Perform “Self Diagnostic Results” in “SHIFT”.

Is any DTC detected?

YES>>

Perform diagnosis of detected DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK DTC OF TCM

With CONSULT

Perform “Self Diagnostic Results” in “TRANSMISSION”.

Is any DTC detected?

YES>>

Perform diagnosis of detected DTC. Refer to DTC Index.

NO>>

GO TO 3.

PERFORM CAN COMMUNICATION LINE CHECK

For the diagnosis procedure, refer to Trouble Diagnosis Flow Chart.

Is the inspection result normal?

YES>>

Replace the TCM. Refer to Removal and Installation.

NO>>

Repair or replace the malfunctioning parts.