Transmission & Driveline :: Transaxle & Transmission

4010 P2783-00 Torque Convereter Temperature

In this manual: Transmission & Driveline :: Transaxle & Transmission
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
61steps
~366min
5/5difficulty
Done 0 of 61
  • P2783-00 Torque Convereter Temperature
  • P2784-00 Input Speed Sensor A/b
  • P2793-00 Gear Shift Direction
  • P27b4-00 Control Module
  • P2871-00 Clutch a
  • P2879-00 Clutch B
  • U007a-00 Control Module Comm Bus H Off
  • U0140-00 Lost Communication (bcm)
  • U0300-00 Can Communication Data

P2783-00 Torque Convereter Temperature Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P2783 00

TORQUE CONVERTER TEMP

(Torque Converter Temperature Too High)
Diagnosis condition Ignition is switched on
Signal —
Threshold Torque converter fluid temperature is more than the specified value
Diagnosis delay time 2 seconds or moer

POSSIBLE CAUSE

  • Cooling system

  • Transaxle assembly

FAIL-SAFE

High oil temperature warning

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Drive the Nissan Pathfinder vehicle for a few minutes under the following conditions.

    Selector lever: D position

  3. Stop the Nissan Pathfinder vehicle.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC (TRANSMISSION)

With CONSULT

  1. Ignition switch ON.

  2. Perform “Self Diagnostic Results” in “TRANSMISSION”.

Is DTC other than P2783-00 detected?

YES>>

Check DTC detected item. Refer to DTC Index.

NO>>

GO TO 2.

CHECK A/T COOLING SYSTEM

Check the A/T cooling system for obstruction/damage/blockage.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace damaged part.

CHECK A/T FLUID

Check A/T fluid level and condition. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>
  1. If A/T fluid is leaking, repair damaged part. Refer to Inspection.

  2. Refill or replace A/T fluid. Refer to Adjustment or Replacement.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Erase DTC of "TRANSMISSION".

  2. Ignition switch OFF and wait for at least 15 seconds.

  3. Ignition switch ON.

  4. Perform DTC Confirmation Procedure.

Is DTC detected?

YES>>

Replace transaxle assembly. Refer to Removal and Installation.

NO>>

INSPECTION END

P2784-00 Input Speed Sensor A/b Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P2784 00

INPUT SPED SEN A/B CORRELATION

(Input/Turbine Speed Sensor "A"/"B" Correlation)
Diagnosis condition Ignition is switched on
Signal —
Threshold Either a electrical or rationality error was detected on the input speed sensor and the engine speed signal is abnormal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • ECM

  • TCM

FAIL-SAFE

  • Shifting is locked

    • While driving: Keeps the gear position when an abnormality is detected

    • When the Nissan Pathfinder vehicle is stopped: Locks in 4th gear position

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

  • Neutral hold mode is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Drive the Nissan Pathfinder vehicle for a few minutes under the following conditions.

    Shift position: D position

  3. Stop the Nissan Pathfinder vehicle.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC (ENGINE)

With CONSULT

  1. Ignition switch ON.

  2. Perform “Self Diagnostic Results” in “ENGINE”.

Is any DTC detected?

YES>>

Check DTC detected item. Refer to DTC Index.

NO>>

GO TO 2.

CHECK A/T COOLING SYSTEM

Replace TCM. Refer to Removal and Installation.

Is the inspection result normal?

>>

WORK END

P2793-00 Gear Shift Direction Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P2793 00

GEAR SHIFT DIRECTION

(Gear Shift Direction Circuit)
1 Diagnosis condition
  • Engine running

  • Shift position: D

Signal —
Threshold

The DTC is detected if any of the following conditions is met:

  • A clutch combination for reverse gear is activated

  • The engine torque is higher than a calibratable threshold while gear engagement via the clutch B, brake C and brake D is active

Diagnosis delay time 2 seconds or more
2 Diagnosis condition
  • Engine running

  • Shift position: R

Signal —
Threshold A clutch combination different from reverse gear is detected
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

TCM

FAIL-SAFE

  • Unable driving

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

  • Neutral hold mode is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Depress the brake pedal.

  3. Shift to the D position and wait for at least 5 seconds.

  4. Shift to the R position and wait for at least 5 seconds.

  5. Press the P position switch.

  6. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

REPLACE TCM

Replace TCM. Refer to Removal and Installation.

>>

WORK END

P27b4-00 Control Module Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P27B4 00

GEAR DIRECTION CONTROL

(Input/Turbine Shaft Speed Sensor "A" Circuit)
1 Diagnosis condition While driving
Signal —
Threshold

The DTC is detected if any of the following conditions is met:

  • The transmission direction is changed while Nissan Pathfinder vehicle speed is more than the specified value or the vehicle speed status is abnormal

  • The transmission direction is reverse and the Nissan Pathfinder vehicle speed is more than the specified value or the vehicle speed signal status is abnormal

Diagnosis delay time 2 seconds or more
2 Diagnosis condition While driving
Signal —
Threshold

The DTC is detected if any of the following conditions is met:

  • A forward gear is engaged and the transmission input direction speed and the transmission output speed direction are not equal

  • A reverse gear is engaged and the transmission input direction speed and the transmission output speed direction are equal

Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

Dual speed sensor

FAIL-SAFE

Not changed from normal driving

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Drive the Nissan Pathfinder vehicle at 80 km/h for at least 5 seconds.

  3. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC (TRANSMISSION)

With CONSULT

  1. Ignition switch ON.

  2. Perform “Self Diagnostic Results” in “TRANSMISSION”.

Is DTC other than P27B4-00 detected?

YES>>

Check DTC detected item. Refer to DTC Index.

NO>>

Replace transaxle assembly. Refer to Removal and Installation.

P2871-00 Clutch a Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P2871 00

CLUTCH A STUCK DISENGAGED

(Clutch "A" Performance/Stuck Disengaged)
1 Diagnosis condition While driving
Signal —
Threshold

The DTC is detected if any of the following conditions is met:

  • Symptom counter for dog clutch A not engaging in down shift is more than the specified number of times

  • Symptom counter for dog clutch A not engaging during gear engagement is more than the specified number of times

  • Symptom counter for ratcheting while gear engagement of dog clutch A is more than the specified number of times

  • Symptom counter for ratcheting while down shift with dog clutch A engagement is more than the specified number of times

Diagnosis delay time 2 second or more
2 Diagnosis condition Engine running
Signal —
Threshold The dog clutch position during engine start by stop/start system is abnormal
Diagnosis delay time 20 seconds

POSSIBLE CAUSE

  • A/T fluid level

  • Dog clutch A position sensor

  • Dog clutch A

  • Transaxle assembly

FAIL-SAFE

  • Shifting is locked (Locks in 4th gear)

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION (PART 1)

  1. Start the engine.

  2. Shift the transmission position according to the following.

    D → N → D

  3. Repeat step 2 3 times.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO>>

GO TO 3.

PERFORM DTC DETECTION (PART 2)

  1. Drive the Nissan Pathfinder vehicle under the following conditions.

    Gear position: 7th → 8th → 7th

  2. Repeat step 1 2 times.

  3. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

GO TO 4.

PERFORM DTC DETECTION (PART 3)

  1. Stop the engine by stop/start system. Refer to System Description.

  2. Restart the engine and wait for at least 25 seconds.

  3. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC (TRANSMISSION)

With CONSULT

  1. Ignition switch ON.

  2. Perform “Self Diagnostic Results” in “TRANSMISSION”.

Is DTC other than P2871-00 detected?

YES>>

Check DTC detected item. Refer to DTC Index.

NO>>

GO TO 2.

CHECK A/T FLUID

Check A/T fluid level and condition. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>
  1. If A/T fluid is leaking, repair damaged part. Refer to Inspection.

  2. Refill or replace A/T fluid. Refer to Adjustment or Replacement.

REPLACE DOG CLUTCH A POSITION SENSOR

Replace dog clutch A position sensor. Refer to Removal and Installation.

>>

GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE

Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

Replace transaxle assembly. Refer to Removal and Installation.

NO>>

INSPECTION END

P2879-00 Clutch B Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P2879 00

CLUTCH B STUCK DISENGAGED

(Clutch "B" Performance/Stuck Disengaged)
Diagnosis condition While driving
Signal —
Threshold

The DTC is detected if any of the following conditions is met:

  • Symptom counter for dog clutch F not engaging in down shift is more than the specified number of times

  • Symptom counter for dog clutch F not engaging during gear engagement is more than the specified number of times

  • Symptom counter for ratcheting while gear engagement of dog clutch F is more than the specified number of times

  • Symptom counter for ratcheting while down shift with dog clutch F engagement is more than the specified number of times

Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • A/T fluid level

  • Dog clutch F position sensor

  • Dog clutch F

  • Transaxle assembly

FAIL-SAFE

  • Shifting is limited (Shifting between the gears of 5 - 6 - 7 - 8 - 9 can be performed)

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

DTC Confirmation Procedure

Always drive vehicle at a safe speed.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Start the engine.

  2. Drive the Nissan Pathfinder vehicle under the following conditions.

    Gear position: 4th → 5th → 4th

  3. Repeat step 1 2 times.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC (TRANSMISSION)

With CONSULT

  1. Ignition switch ON.

  2. Perform “Self Diagnostic Results” in “TRANSMISSION”.

Is DTC other than P2879-00 detected?

YES>>

Check DTC detected item. Refer to DTC Index.

NO>>

GO TO 2.

CHECK A/T FLUID

Check A/T fluid level and condition. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>
  1. If A/T fluid is leaking, repair damaged part. Refer to Inspection.

  2. Refill or replace A/T fluid. Refer to Adjustment or Replacement.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Erase DTC of "TRANSMISSION".

  2. Ignition switch OFF and wait for at least 15 seconds.

  3. Ignition switch ON.

  4. Perform DTC Confirmation Procedure.

Is DTC detected?

YES>>

Replace transaxle assembly. Refer to Removal and Installation.

NO>>

INSPECTION END

U007a-00 Control Module Comm Bus H Off Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U007A 00

Control module comm Bus H Off

(Control Module Communication Bus "H" Off)
Diagnosis condition Ignition is switched on
Signal CAN communication signal
Threshold Bus state: Buss off
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Harness or connector (CAN communication line is error)

  • All control units at network

FAIL-SAFE

  • Shifting is locked

    • While driving: Keeps the gear position when an abnormality is detected

    • When the Nissan Pathfinder vehicle is stopped: Locks in 4th gear position

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

  • Neutral hold mode is prohibited (if equipped)

DTC CONFIRMATION PROCEDURE

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Ignition switch ON and wait for at least 5 seconds.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

For the diagnosis procedure, refer to Trouble Diagnosis Flow Chart.

U0140-00 Lost Communication (bcm) Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U0140 00

LOST COMM (BCM)

(Lost Communication With Body Control Module)
Diagnosis condition Ignition is switched on
Signal CAN communication signal
Threshold TCM is unable to receive the CAN communications signal from BCM
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

  • Harness or connector (CAN communication line)

  • Power supply voltage circuit or ground circuit of the BCM

  • BCM

  • TCM

FAIL-SAFE

  • Manual mode is prohibited

  • Neutral hold mode is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Ignition switch ON and wait for at least 5 seconds.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

For the diagnosis procedure, refer to Trouble Diagnosis Flow Chart.

U0300-00 Can Communication Data Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U0300 00

CAN COMM DATA

(Internal Control Module Software Incompatibility)
Diagnosis condition Ignition is switched on
Signal CAN communication signal
Threshold The data length transmitted from each control unit is shorter than the specified length and the status
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

TCM software

FAIL-SAFE

  • Manual mode is prohibited

  • Stop/start system is prohibited (if equipped)

DTC Confirmation Procedure

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 15 seconds, then perform the next test.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 9 V.

>>

GO TO 2.

PERFORM DTC DETECTION

  1. Ignition switch ON.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM DOG CLUTCH POSITION SENSOR CALIBRATION

Perform dog clutch position sensor calibration. Refer to Description.

>>

GO TO 2.

PERFORM LEARNING OF SOLENOID CHARACTERISTIC

Perform learning of solenoid characteristic. Refer to Description.

>>

GO TO 3.

PERFORM A/T CLUTCH TOUCH POINT LEARNING

Perform A/T clutch touch point learning. Refer to Description.

>>

GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE

Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

Replace TCM. Refer to Removal and Installation.

NO>>

INSPECTION END