Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock

Dtc/circuit Diagnosis (B2001-45 Intelligent Key Unit ... B2417-15 Touch Sensor Circuit Lh Open)

In this manual: Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
83steps
~498min
4/5difficulty
Done 0 of 83
  • B2001-45 Intelligent Key Unit
  • B2010-1c Battery Voltage
  • B203c-14 Inside Antenna
  • B203e-14 Outside Antenna
  • B2046-42 Eeprom
  • B2087 One Touch Sensor (fl)
  • B2086-23: Request Sw (bd/tr)
  • B2409-12 Half Latch Switch
  • B2409-14 Half Latch Switch
  • B2417-15 Touch Sensor Circuit Lh Open

B2001-45 Intelligent Key Unit Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC Detection Condition
B2001-45

Intelligent Key unit

(Intelligent Key unit)
Diagnosis condition Ignition switch ON
Signal (terminal) —
Threshold Intelligent Key unit is internal malfunctioning
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Intelligent Key unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Erase DTC.

  2. Ignition switch OFF.

  3. Ignition switch ON.

  4. Check “Self Diagnostic Result” mode of “HANDS FREE MODULE”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

REPLACE INTELLIGENT KEY UNIT

When DTC “B2001-45” is detected, replace Intelligent Key unit.

>>

Replace Intelligent Key unit. Refer to Removal and Installation.

B2010-1c Battery Voltage Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC Detection Condition
B2010-1C

Battery voltage

(Battery voltage)
Diagnosis condition All times
Signal (terminal) Intelligent Key unit battery power supply signal
Threshold Less than 4 V or more than 16 V
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connector (power supply circuit)

  • Intelligent Key unit

  • Battery

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Erase DTC.

  2. Ignition switch OFF.

  3. Ignition switch ON.

  4. Check “Self Diagnostic Result” mode of “HANDS FREE MODULE”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK BATTERY VOLTAGE

Measure the battery voltage. Refer to How to Handle Battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace battery.

CHECK POWER SUPPLY CIRCUIT

Check Intelligent Key unit power supply circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace Intelligent Key unit. Refer to Removal and Installation.

NO>>

Repair the malfunctioning part.

B203c-14 Inside Antenna Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detecting condition
B203C-14

Inside antenna

(Inside antenna)
Diagnosis condition Work support “INSIDE/OUTSIDE ANT DIAGNOSIS”: activated
Signal (terminal) Inside key antenna (console) signal (Intelligent Key unit connector terminal: 33, 34)
Threshold Inside key antenna (console) circuit is shorted to ground
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Intelligent Key unit

  • Inside key antenna (console)

  • Harness or connector (inside key antenna (console) circuit is open or shorted)

FAIL-SAFE

–

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Select “INSIDE/OUTSIDE ANT DIAGNOSIS” in “WORK SUPPORT” mode of “HANDS FREE MODULE”.

  2. Check the “Self Diagnosis Result” mode of “HANDS FREE MODULE”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK INSIDE KEY ANTENNA (CONSOLE) INPUT SIGNAL 1

  1. Ignition switch ON.

  2. Check signal between Intelligent Key unit harness connector and ground using oscilloscope.

    (+)(–)Condition

    Signal

    (Reference value)
    Intelligent Key unit
    ConnectorTerminal
    M38 33 Ground Press push-button ignition switch When Intelligent Key is in the passenger compartment
    When Intelligent Key is not in the passenger compartment
    34 When Intelligent Key is in the passenger compartment
    When Intelligent Key is not in the passenger compartment

Is the inspection result normal?

YES>>

Replace Intelligent Key unit. Refer to Removal and Installation.

NO>>

GO TO 2.

CHECK INSIDE KEY ANTENNA (CONSOLE) CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect Intelligent Key unit connector and inside key antenna (console) connector.

  3. Check continuity between Intelligent Key unit harness connector and inside key antenna (console) harness connector.

    Intelligent Key unitInside key antenna (console)Continuity
    ConnectorTerminalConnectorTerminal
    M38 33 M147 2 Yes
    34 1
  4. Check continuity between Intelligent Key unit harness connector and ground.

    Intelligent Key unit(-)Continuity
    ConnectorTerminal
    M38 33 Ground No
    34

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness.

CHECK INSIDE KEY ANTENNA (CONSOLE) INPUT SIGNAL 2

  1. Replace inside key antenna (console). (New antenna or other antenna)

  2. Connect Intelligent Key unit connector and inside key antenna connector.

  3. Ignition switch ON.

  4. Check signal between Intelligent Key unit harness connector and ground using oscilloscope.

    (+)(–)Condition

    Signal

    (Reference value)
    Intelligent Key unit
    ConnectorTerminal
    M38 33 Ground Press push-button ignition switch When Intelligent Key is in the passenger compartment
    When Intelligent Key is not in the passenger compartment
    34 When Intelligent Key is in the passenger compartment
    When Intelligent Key is not in the passenger compartment

Is the inspection result normal?

YES>>

Replace inside key antenna (console). Refer to Removal and Installation.

NO>>

Replace Intelligent Key unit. Refer to Removal and Installation.

B203e-14 Outside Antenna Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detecting condition
B203E-14

Outside antenna

(Outside antenna)
Diagnosis condition Work support “INSIDE/OUTSIDE ANT DIAGNOSIS”: activated
Signal (terminal) Outside key antenna (rear door LH) signal (Intelligent Key unit connector terminal: 35, 36)
Threshold Outside key antenna (rear door LH) circuit is shorted to ground
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Intelligent Key unit

  • Outside key antenna (rear door LH)

  • Harness or connector [outside key antenna (rear door LH) circuit is open or shorted]

FAIL-SAFE

–

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Select “INSIDE/OUTSIDE ANT DIAGNOSIS” in “WORK SUPPORT” mode of “HANDS FREE MODULE”.

  2. Check “Self Diagnosis Result” mode of “HANDS FREE MODULE”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK OUTSIDE KEY ANTENNA (REAR DOOR LH) INPUT SIGNAL 1

  1. Ignition switch ON.

  2. Check signal between Intelligent Key unit harness connector and ground using oscilloscope.

    (+)(–)Condition

    Signal

    (Reference value)
    Intelligent Key unit
    ConnectorTerminal
    M38 35 Ground When the door request switch (front door LH or rear door LH) is operated with ignition switch ON When Intelligent Key is in the antenna detection area
    When Intelligent Key is not in the antenna detection area
    36 When Intelligent Key is in the antenna detection area
    When Intelligent Key is not in the antenna detection area

Is the inspection result normal?

YES>>

Replace Intelligent Key unit. Refer to Removal and Installation.

NO>>

GO TO 2.

CHECK OUTSIDE KEY ANTENNA (REAR DOOR LH) CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect Intelligent Key unit connector and outside key antenna (rear door LH) connector.

  3. Check continuity between Intelligent Key unit harness connector and outside key antenna (rear door LH) connector.

    Intelligent Key unitOutside key antenna (rear door LH)Continuity
    ConnectorTerminalConnectorTerminal
    M38 35 D203 2 Yes
    36 1
  4. Check continuity between Intelligent Key unit harness connector and ground.

    Intelligent Key unit(-)Continuity
    ConnectorTerminal
    M38 35 Ground No
    36

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness.

CHECK OUTSIDE KEY ANTENNA (REAR DOOR LH) INPUT SIGNAL 2

  1. Replace outside key antenna (rear door LH). (New antenna or other antenna)

  2. Connect Intelligent Key unit connector and outside key antenna (rear door LH) connector.

  3. Ignition switch ON.

  4. Check signal between Intelligent Key unit harness connector and ground using oscilloscope.

    (+)(–)Condition

    Signal

    (Reference value)
    Intelligent Key unit
    ConnectorTerminal
    M38 35 Ground When the door request switch (front door LH or rear door LH) is operated with ignition switch ON When Intelligent Key is in the antenna detection area
    When Intelligent Key is not in the antenna detection area
    36 When Intelligent Key is in the antenna detection area
    When Intelligent Key is not in the antenna detection area

Is the inspection result normal?

YES>>

Replace outside key antenna (rear door LH). Refer to Removal and Installation.

NO>>

Replace Intelligent Key unit. Refer to Removal and Installation.

B2046-42 Eeprom Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC Detection Condition
B2046-42

EEPROM

(Electrically Erasable Programmable Read-Only Memory)
Diagnosis condition Ignition switch ON
Signal (terminal) —
Threshold EEPROM in Intelligent Key unit is malfunctioning
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Intelligent Key unit

  • Mistook the "Re programming"

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

DTC CONFIRMATION

CONSULT

  1. Erase DTC.

  2. Ignition switch OFF.

  3. Ignition switch ON.

  4. Check “Self Diagnostic Result” mode of “HANDS FREE MODULE”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM "REPROGRAMING"

CONSULT

  1. Perform "Reprograming".

  2. Erase DTC.

  3. Ignition switch OFF.

  4. Ignition switch ON.

  5. Check “Self Diagnostic Result” mode of “HANDS FREE MODULE”.

Is DTC detected?

YES>>

GO TO 2.

NO>>

Inspection End.

REPLACE INTELLIGENT KEY UNIT

Replace Intelligent Key unit. Refer to Removal and Installation.

>>

Inspection End.

B2087 One Touch Sensor (fl) Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC Detection Condition
B2087-08

One touch sensor (FL)

[Request switch (front left side)]
[BUS] Diagnosis condition Ignition switch ON
Signal (terminal) Door request switch signal (Intelligent Key unit connector terminal 4)
Threshold Intelligent Key unit detects that the front door request switch LH is stuck ON
Diagnosis delay time 10 seconds or more
B2087-11 [GND-SHORT} Diagnosis condition Ignition switch ON
Signal (terminal) Door request switch signal (Intelligent Key unit connector terminal 4)
Threshold Intelligent Key unit detects that the front door request switch LH is stuck ON
Diagnosis delay time 10 seconds or more
B2087-23 [LOWER LIMIT ERR] Diagnosis condition Ignition switch ON
Signal (terminal) Door request switch signal (Intelligent Key unit connector terminal 4)
Threshold Intelligent Key unit detects that the front door request switch LH is stuck ON
Diagnosis delay time 10 seconds or more
B2087-24 [UPPER LIMIT ERR] Diagnosis condition Ignition switch ON
Signal (terminal) Door request switch signal (Intelligent Key unit connector terminal 4)
Threshold Intelligent Key unit detects that the front door request switch LH is stuck ON
Diagnosis delay time 10 seconds or more
B2087-44 [DATA MEM FAIL] Diagnosis condition Ignition switch ON
Signal (terminal) Door request switch signal (Intelligent Key unit connector terminal 4)
Threshold Intelligent Key unit detects that the front door request switch LH is stuck ON
Diagnosis delay time 10 seconds or more

POSSIBLE CAUSE

  • Front door request switch LH

  • Harness or connector (front door request switch LH circuit is shorted)

  • Intelligent Key unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

CONSULT

  1. Ignition switch ON and wait for 10 seconds or more.

  2. Check “Self Diagnostic Result” mode of “HANDS FREE MODULE”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK DOOR REQUEST SWITCH INPUT SIGNAL

  1. Ignition switch OFF.

  2. Disconnect front door request switch LH connector.

  3. Check voltage between front door request switch LH harness connector and ground.

    (+)(–)

    Voltage

    (Approx.)
    Front door request switch LH
    ConnectorTerminal
    D3 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK DOOR REQUEST SWITCH CIRCUIT

  1. Disconnect Intelligent Key unit connector.

  2. Check continuity between front door request switch LH harness connector and Intelligent Key unit harness connector.

    Front door request switch LHIntelligent Key unitContinuity
    ConnectorTerminalConnectorTerminal
    D3 1 M38 4 Yes
  3. Check continuity between front door request switch LH harness connector and ground.

    Front door request switch LH(-)Continuity
    ConnectorTerminal
    D3 1 Ground No

Is the inspection result normal?

YES>>

Replace Intelligent Key unit. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK DOOR REQUEST SWITCH GROUND CIRCUIT

Check continuity between front door request switch LH harness connector and ground.

Front door request switch LH(-)Continuity
ConnectorTerminal
D3 2 Ground Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK DOOR REQUEST SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace front door outside handle. Refer to Removal and Installation.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

Inspection End.

B2086-23: Request Sw (bd/tr) Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC Detection Condition
B2086-23

Request SW (BD/TR)

[Request switch (back door/trunk)]
Diagnosis condition Ignition switch ON
Signal (terminal) Door request switch signal (Intelligent Key unit connector terminal 5)
Threshold Intelligent Key unit detects that the back door request switch is stuck ON
Diagnosis delay time 10 seconds or more

POSSIBLE CAUSE

  • Back door opener switch

  • Harness or connector (back door request switch circuit is shorted)

  • Intelligent Key unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

CONSULT

  1. Ignition switch ON and wait for 10 seconds or more.

  2. Check “Self Diagnostic Result” mode of “HANDS FREE MODULE”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK BACK DOOR REQUEST SWITCH INPUT SIGNAL

  1. Ignition switch OFF.

  2. Disconnect back door opener switch connector.

  3. Check voltage between back door opener switch harness connector and ground.

    (+)(–)

    Voltage

    (Approx.)
    Back door opener switch
    ConnectorTerminal
    D559 4 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK BACK DOOR REQUEST SWITCH CIRCUIT

  1. Disconnect Intelligent Key unit connector.

  2. Check continuity between back door opener switch harness connector and Intelligent Key unit harness connector.

    Back door opener switchIntelligent Key unitContinuity
    ConnectorTerminalConnectorTerminal
    D559 4 M38 5 Yes
  3. Check continuity between back door opener switch harness connector and ground.

    Back door opener switch—Continuity
    ConnectorTerminal
    D559 4 Ground No

Is the inspection result normal?

YES>>

Replace Intelligent Key unit. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK BACK DOOR REQUEST SWITCH GROUND CIRCUIT

Check continuity between back door opener switch harness connector and ground.

Back door opener switch—Continuity
ConnectorTerminal
D559 3 Ground Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK BACK DOOR REQUEST SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace back door opener switch. Refer to Removal and Installation.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

Inspection End.

B2409-12 Half Latch Switch Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC Detection Condition
B2409-12

Half latch switch

(Half latch switch)
Diagnosis condition When the door unlock operates while ignition switch is OFF (auto ACC OFF status) or the battery terminal is removed
Signal (terminal) Half latch switch signal
Threshold Automatic back door control unit detect power short of half latch switch circuit
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector (half latch switch circuit is power short)

  • Automatic back door control unit

  • Back door lock assembly (half latch switch)

FAIL-SAFE

Inhibit automatic back door system [only operate back door closure function (open function)]

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. When the door unlock operates by Intelligent Key or door request switch while ignition switch is OFF (auto ACC OFF status).

  2. Check “Self Diagnostic Result” mode of “AUTO BACK DOOR”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK HALF LATCH SWITCH INPUT SIGNAL

Check voltage between automatic back door control unit harness connector and ground.

(+)(–)Condition

Voltage

(Approx.)
Automatic back door control unit
ConnectorTerminal
B55 10 Ground Back door Open 0V
Fully closed/ half latch Battery voltage

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

GO TO 2.

CHECK HALF LATCH SWITCH CIRCUIT

  1. Disconnect automatic back door control unit connector and back door lock assembly connector.

  2. Check voltage between automatic back door control unit harness connector and ground.

    Automatic back door control unit—Voltage
    ConnectorTerminal
    B55 10 Ground 0 V

Is the inspection result normal?

YES>>

Replace back door lock assembly. Refer to Removal and Installation.

NO>>

Repair or replace harness.

B2409-14 Half Latch Switch Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC Detection Condition
B2409-14

Half latch switch

(Half latch switch)
Diagnosis condition When back door open
Signal (terminal) Half latch switch signal
Threshold

Automatic back door control unit detects when one of the following conditions is satisfied

  • Half latch switch circuit is ground short

  • Half latch switch is stuck ON

Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector (half latch switch circuit is ground short)

  • Automatic back door control unit

  • Back door lock assembly (half latch switch)

FAIL-SAFE

  • Inhibit automatic back door system [only operate back door closure function (open function)]

  • Manual latch and unlatch functions available only

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Operate automatic back door.

  3. Check “Self Diagnostic Result” mode of “AUTO BACK DOOR”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK HALF LATCH SWITCH INPUT SIGNAL

Check voltage between automatic back door control unit harness connector and ground.

(+)(–)Condition

Voltage

(Approx.)
Automatic back door control unit
ConnectorTerminal
B55 10 Ground Back door Open 0 V
Fully closed/ half latch Battery voltage

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

GO TO 2.

CHECK HALF LATCH SWITCH CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect automatic back door control unit connector and back door lock assembly connector.

  3. Check continuity between automatic back door control unit harness connector and back door lock assembly harness connector.

    Automatic back door control unitBack door lock assemblyContinuity
    ConnectorTerminalConnectorTerminal
    B55 10 D557 6 Yes
  4. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit(-)Continuity
    ConnectorTerminal
    B55 10 Ground No

Is the inspection result normal?

YES>>

Replace back door lock assembly. Refer to Removal and Installation.

NO>>

Repair or replace harness.

B2417-15 Touch Sensor Circuit Lh Open Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC Detection Condition
B2417-15

Touch sensor circuit LH open

(Touch sensor circuit left hand open)
Diagnosis condition All times
Signal (terminal) Touch sensor LH signal
Threshold

Automatic back door control unit detects when one of the following conditions is satisfied

  • Touch sensor LH circuit is open or shorted

  • Malfunction of touch sensor LH

Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector (touch sensor LH circuit is open or shorted)

  • Automatic back door control unit

  • Touch sensor LH

FAIL-SAFE

Inhibit automatic back door system (only operate back door closure function)

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Check “Self Diagnostic Result” mode of “AUTO BACK DOOR”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK TOUCH SENSOR LH INPUT SIGNAL

Check voltage between automatic back door control unit harness connector and ground.

(+)(–)Condition

Voltage

(Approx.)
Automatic back door control unit
ConnectorTerminal
B55 12 Ground Touch sensor LH Detect obstruction 0.2 – 3 V
Other than above 3.4 – 6.5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 5.

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the automatic back door control unit harness connector for disconnection or looseness.

  3. Check the touch sensor LH harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair/replace harness or connector, securely lock the connector, and GO TO 5.

CHECK AUTOMATIC BACK DOOR CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT

Check the automatic back door control unit power supply and ground circuits. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair/replace harness, connector, fuse, or fusible link, and GO TO 5.

CHECK TERMINAL

  1. Ignition switch OFF.

  2. Disconnect automatic back door control unit harness connector and then check the automatic back door control unit pin terminals for damage or loose connection with harness connector.

  3. Disconnect touch sensor LH harness connector and check touch sensor LH pin terminal for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

Replace automatic back door control unit. Refer to Removal and Installation.

NO>>

Repair/replace harness, connector, or terminal.

CHECK TOUCH SENSOR LH CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect automatic back door control unit connector and touch sensor LH connector.

  3. Check continuity between automatic back door control unit harness connector and touch sensor LH harness connector.

    Automatic back door control unitTouch sensor LHContinuity
    ConnectorTerminalConnectorTerminal
    B55 12 D530 1 Yes
  4. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit(-)Continuity
    ConnectorTerminal
    B55 12 Ground No

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

CHECK TOUCH SENSOR LH GROUND CIRCUIT

  1. Disconnect touch sensor RH connector.

  2. Check continuity between automatic back door control unit harness connector and touch sensor LH harness connector.

    Automatic back door control unitTouch sensor LHContinuity
    ConnectorTerminalConnectorTerminal
    B55 14 D530 4 Yes
  3. Check continuity between automatic back door control unit harness connector and ground.

    Automatic back door control unit(-)Continuity
    ConnectorTerminal
    B55 14 Ground No

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace harness.

CHECK TOUCH LH SENSOR

Check touch sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace touch sensor LH. Refer to Removal and Installation.