Engine :: Engine Mechanical

Removal and Installation - Front Timing Chain Case ++

In this manual: Engine :: Engine Mechanical
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
11steps
~66min
5/5difficulty
0102030405028.421N·mlb·ft
Tightening torque found on this page
Done 0 of 11

Exploded View

1. Engine assembly 2. Front timing chain case oil filter 3. Crankshaft pulley
4. Front oil seal 5. Front timing chain case 6. O-ring
A. To valve timing control cover (bank 1/bank 2). Refer to Exploded View. B. Refer to Removal and Installation. Front

Removal and Installation

Remove and secure engine assembly to stand. Refer to Setting.

If removing the timing chains, obtain compression TDC of No. 1 cylinder as follows:Disconnect the vacuum hose from intake manifold collector. Refer to Exploded View. Disconnect the engine mount insulator (front) vacuum hose. Refer to Exploded View. Disconnect VIAS control solenoid valve harness connectors. Refer to Component Parts Location. Disconnect the harness connector from the electronic controlled engine mount control solenoid valve. Remove the electronic controlled engine mount control solenoid valve. Refer to Component Parts Location. Remove the EVAP canister purge volume control solenoid valve hose. Refer to Exploded View. Disconnect the EVAP canister purge volume control solenoid valve harness connector. Refer to Exploded View. Disconnect electronic throttle control actuator harness connector. Refer to Exploded View. Disconnect PCV hose from intake manifold collector. Loosen the intake manifold collector bolts and nuts in reverse of the sequence shown and then remove the intake manifold collector and intake manifold collector gasket.

Loosen intake manifold nuts and bolts in reverse of the sequence shown.

: Engine front

Remove intake manifold and intake manifold gasket. Remove intake manifold studs (if necessary). Remove bolts (A) and remove high pressure fuel pump cover (1).
Remove high pressure fuel pump insulator. Refer to Exploded View. Remove insulator. Refer to Exploded View. Release clip (A) and disconnect fuel feed hose (1) from high pressure fuel pump (2).
Disengage fuel feed hose from clip and reposition. Remove bolts from fuel feed tube bracket and reposition fuel feed tube bracket and harness. Remove high pressure fuel tube (pump side). Refer to Exploded View. Disconnect the harness connector from the high pressure fuel pump. Loosen high pressure fuel pump bolts while alternating sides frequently and remove high pressure fuel pump. Disconnect the exhaust camshaft position sensor (bank 2), exhaust camshaft position sensor (bank 1), intake camshaft position sensor (bank 2), intake camshaft position sensor (bank 1) harness connectors. Remove the exhaust camshaft position sensor (bank 2), exhaust camshaft position sensor (bank 1), intake camshaft position sensor (bank 2), intake camshaft position sensor (bank 1). Refer to Exploded View. Remove ignition coils. Refer to Exploded View. Loosen rocker cover bolts in reverse of the sequence shown.
  • Rocker cover (bank 2)

  • Rocker cover (bank 1)

    : Engine front
Remove the rocker cover (bank 2/bank 1) and rocker cover gasket (bank 2/bank 1). Rotate crankshaft pulley clockwise to align timing mark (grooved line without color) with timing indicator (A).
Check that intake and exhaust camshaft lobes on No. 1 cylinder (RH of engine) are located as shown.

: Engine front

  • If not, turn the crankshaft one revolution (360°) and align as shown.

While securely holding the hexagonal part in pulley center of drive belt auto-tensioner, move in the direction of arrow (loosening direction of drive belt auto-tensioner) using suitable tool.

Insert a rod approximately 6 mm (0.24 in) in diameter through the rear of drive belt auto-tensioner into retaining boss to lock drive belt auto-tensioner pulley.

Remove drive belt from crankshaft pulley and then remove it from the other pulleys.

Disconnect the harness connectors from the compressor.

Remove the compressor. Refer to Exploded View.

Remove "B" terminal nut and disconnect "B" terminal harness.

Disconnect the harness connector from generator.

Remove the generator. Refer to Exploded View.

Remove the crankshaft pulley as follows:

  • Secure crankshaft pulley with a suitable tool.

  • Loosen crankshaft pulley bolt and locate bolt seating surface at 10 mm (0.39 in) from its original position.

  • Position a suitable tool at recess hole of crankshaft pulley to remove crankshaft pulley.

Disconnect the harness connector from the engine oil pressure sensor and engine oil temperature sensor.

Remove water pipe. Refer to Exploded View.

Disconnect the water hoses from the oil cooler.

Loosen the oil pan (lower) bolts in reverse of the sequence shown.

Remove the oil pan (lower).

  • After removing the bolts, separate the mating surface and remove the old liquid gasket using Tool (A).

  • Tap (B) the Tool to insert it.

  • In areas where the Tool is difficult to use, lightly tap (C) to slide it.

    Tool number (A) : KV10111100 (NI-37228)

Remove the old sealant from the bolt holes and threads.

Disconnect the harness connector from the engine oil pressure control solenoid valve.

Remove bolts (B) and remove engine oil pressure control solenoid valve (2).

Remove bolt (A) and remove oil pump drive chain cover (1).

Rotate oil pump drive chain tensioner (1) counterclockwise with a suitable tool and remove oil pump drive chain (2) from oil pump gear.

Remove the oil pump bolts (A) in reverse of the sequence shown and remove (if necessary).

Remove the oil pan (upper) using the following procedure:Remove the oil pan (upper) bolts in reverse of the sequence shown.

Insert a suitable tool (B) into the notch (C) of the oil pan [upper (1)] as shown.
Remove the oil pan (upper) by moving the suitable tool up and down (A) as shown.

Remove the O-ring from the bottom of the cylinder block and oil pump housing.

Remove front cover gasket and rear oil seal retainer gasket.

Remove the old sealant from the mating surfaces using a suitable tool (A).

  • Also remove the old sealant from mating surface of the cylinder block.

  • Remove the old sealant from the bolt holes and threads.

Remove engine mounting bracket (RH). Refer to Exploded View.

Disconnect the harness connectors from electric intake valve timing control actuator and the exhaust valve timing control solenoid valve. Refer to Exploded View.

Remove the intake valve timing control cover [bank 1 (A)] and intake valve timing control cover [bank 2 (B)].

  • Loosen the intake valve timing control cover [bank 1 (A)] and intake valve timing control cover [bank 2 (B)] bolts in the reverse order as shown.

Loosen the front timing chain case bolts in reverse of the sequence shown and remove bolts.

Insert the appropriate size suitable tool into the notch (A) at the top of the front timing chain case as shown.

Pry off the case by moving the suitable tool (B) as shown.
  • Cut liquid gasket for removal using Tool.

Remove O-rings (1) from rear timing chain case.

(A) : Bank 1
(B) : Bank 2

Remove the front oil seal from the front timing chain case using a suitable tool.

Remove all old liquid gasket (A) from all the bolt holes (B) and bolts.

Use a suitable tool to remove all of the old liquid gasket from the front timing chain case and opposite mating surfaces.

Remove front timing chain case oil filters (if necessary).

Install front timing chain case oil filter (2) (if necessary).

  • Ensure oil filter mesh remains intact during insertion into the front timing chain case (1).

  • Ensure oil filter mesh does not protrude from front timing chain case (1).

(A) : 1.0 - 1.5 mm (0.039 - 0.059 in)

Install the new front oil seal on the front timing chain case. Apply new engine oil to the oil seal edges.

(A) : Engine inside
(B) : Oil seal lip
(C) : Dust seal lip
(D) : Engine outside

Install the new front oil seal so that it becomes flush with the face of front timing chain case using suitable tool.

Install new O-rings (1) on rear timing chain case.

(A) : Bank 1
(B) : Bank 2

Apply liquid gasket to front timing chain case as shown.

  • Use Genuine Silicone RTV Sealant or equivalent. Refer to Recommended Chemical Products and Sealants.

  • Before installation, wipe off the protruding liquid gasket.

  • (C): 2.6 - 3.6 mm (0.102 - 0.142 in) diameter.

Install the front timing chain case by aligning the dowel pin on the rear timing chain case with the dowel pin hole in front timing chain case.

Loosely install the front timing chain case bolts.

Bolt position Bolt diameter
1, 2 : 8 mm (0.31 in)
3 – 22 : 6 mm (0.24 in)

Tighten the front timing chain case bolts to the specified torque in the sequence shown.

  • Retighten the front timing chain case bolts to the specified torque in the sequence shown

Bolt position Tightening specification
1, 2 : 28 N·m
3 – 22 : 12,7 N·m

Install intake valve timing control cover (bank 1) and intake valve timing control cover (bank 2) using the following procedure:Install the O-rings to the front timing chain case.

Install the O-rings (1) to the valve timing control cover (bank 1). Apply a bead of liquid gasket (C) to the valve timing control cover [bank 1 (2)] as shown.

Use Genuine Silicone RTV Sealant or equivalent. Refer to Recommended Chemical Products and Sealants.

(1) : Front timing chain case
(A) : 4.0 - 5.6 mm (0.157 - 0.220 in)
(B) : 3.4 - 4.4 mm (0.134 - 0.173 in)

Apply a bead of liquid gasket (C) to the valve timing control cover [bank 2 (2)] as shown.

Use Genuine Silicone RTV Sealant or equivalent. Refer to Recommended Chemical Products and Sealants.

(1) : Front timing chain case
(A) : 4.0 - 5.6 mm (0.157 - 0.220 in)
(B) : 3.4 - 4.4 mm (0.134 - 0.173 in)

Align valve timing control cover (bank 1) with dowels in front timing chain case and install valve timing control cover (bank 1). Install and tighten valve timing control cover (bank 1) bolts (A) to the specified torque in the sequence shown.

Bolts : 11,3 N·m
(B) : Bank 2

Install and tighten the electric intake valve timing control actuator to the specified torque.

Electric intake valve timing control actuator bolts : 9 N·m

Apply sealant (A) to the front cover gasket and the rear oil seal retainer gasket as shown.

Use Genuine RTV Silicone Sealant or equivalent. Refer to Recommended Chemical Products and Sealants.

Dimension (B) : 15 mm (0.59 in)
Dimension (C) : 5 mm (0.20 in)

Install the front cover gasket (1) and rear oil seal retainer gasket (2) as shown.

: Engine front

Apply a bead of sealant to the cylinder block mating surface of the oil pan (upper) as shown.

Be sure the sealant is applied 4.0 - 5.0 mm (0.157 - 0.197 in) as shown. Increase the bead to 4.5 - 5.5 mm (0.177 - 0.217 in) at the locations (A) indicated.

Use Genuine RTV Silicone Sealant, or equivalent. Refer to Recommended Chemical Products and Sealants.

: Engine front

Install new O-ring (1) into the cylinder block before installing oil pan (upper).

  1. : Crankshaft pulley

Install the oil pan (upper).

  • Tighten bolts (1) and (2) to specification within five minutes of applying the liquid gasket.

  • Tighten the remaining oil pan (upper) bolts to specification in the sequence shown.

Oil pan (upper) bolts : 22 N·m

Install the oil pump and new O-rings (1) and tighten oil pump bolts (A) to the specified torque in the sequence shown (if removed).

Oil pump bolts : 22 N·m

Apply a continuous bead of sealant to the oil pan (lower).

  • Be sure the sealant is 4.5 - 5.5 mm (0.177 - 0.217 in) wide.

  • Use Genuine Silicone RTV Sealant, or equivalent. Refer to Recommended Chemical Products and Sealants.

(A) : Groove
(B) : Bolt hole
: Inside

Install the oil pan (lower) and tighten the oil pan (lower) bolts to the specified torque in the sequence shown.

Oil pan (lower) bolts : 8,8 N·m

Install crankshaft pulley and tighten the bolt using the following procedure:

  • Lubricate thread and seat surface of the bolt with new engine oil.

  • Secure the crankshaft pulley using a suitable tool.

  • For the second step, angle tighten using Tool.

Step 1 : 90 N·m
Step 2 : 90° - 96° clockwise

Tool number : KV10112100 (BT-8653-A)

Install components removed to obtain compression TDC of No.1 cylinder using the following procedure:Install rocker cover (bank 1) using the following procedure:

  1. Apply a 3 mm (0.12 mm) bead of sealant to the areas on the front corners using a suitable tool.

    Use Genuine Silicone RTV Sealant or equivalent. Refer to Recommended Chemical Products and Sealants.

    (1) : Camshaft bracket
    (2) : Cylinder head
    (A) : 4 mm (0.16 in)
    (B) : 5 mm (0.20 in)
    (C) : 4 mm (0.16 in)
    (E) : 10 mm (0.39 in)
  2. Tighten the rocker cover bolts to the specified torque in the sequence shown.

    Rocker cover bolts
    Step 1 : 2 N·m
    Step 2 : 8,3 N·m
    : Engine front
Install rocker cover (bank 2) using the following procedure:
  1. Apply a 3 mm (0.12 mm) bead of sealant to the areas on the front corners using a suitable tool.

    Use Genuine Silicone RTV Sealant or equivalent. Refer to Recommended Chemical Products and Sealants.

    (1) : Camshaft bracket
    (2) : Cylinder head
    (A) : 4 mm (0.16 in)
    (B) : 5 mm (0.20 in)
    (C) : 4 mm (0.16 in)
    (E) : 10 mm (0.39 in)
  2. Tighten the rocker cover bolts to the specified torque in the sequence shown.

    Rocker cover bolts
    Step 1 : 2 N·m
    Step 2 : 8,3 N·m
Install spark plugs and ignition coils. Refer to Exploded View. Connect the exhaust camshaft position sensor (bank 2), exhaust camshaft position sensor (bank 1), intake camshaft position sensor (bank 2), intake camshaft position sensor (bank 1) harness connectors. Install O-ring to high pressure fuel pump. Rotate engine clockwise and visually check for bottom dead center of high pressure fuel pump lobe on camshaft. Apply clean engine oil to high pressure fuel pump bore. Install high pressure fuel pump and tighten the bolts using the following procedure:
  1. Tighten bolts one revolution while alternating sides until high pressure fuel pump is mated to No. 1 camshaft bracket.

  2. Tighten bolts to the specified torque.

    High pressure fuel pump bolts : 26 N·m
Connect harness connector to high pressure fuel pump. Install high pressure fuel tube (pump side) using the following procedure:
  1. Install high pressure fuel tube [pump side (2)] and hand tighten flare nut (A) and flare nut (C) until contact seat.

    (1) : High pressure fuel tube (bank side)
    (D) : High pressure fuel tube (bank side) flare nut
    (E) : High pressure fuel tube (bank side) flare nut

  2. Hand tighten bolt (B).

  3. Tighten flare nut (C) and then flare nut (A) to the specified torque.

    Flare nut : 15 N·m

  4. Tighten flare nut (C) and then flare nut (A) to the specified torque.

    Flare nut : 23 N·m

  5. Tighten bolt (B) to the specified torque.

    Bolt : 13,5 N·m

Connect fuel feed hose (1) to high pressure fuel pump (2).

(A) : Clip

Install high pressure fuel pump insulator. Tighten high pressure fuel pump cover bolts to the specified torque in the sequence shown.

High pressure fuel pump cover bolts : 11 N·m
: Engine front

Install intake manifold insulator. Refer to Exploded View. Install intake manifold studs (if removed). Refer to Exploded View. Install intake manifold and tighten intake manifold nuts and bolts to the specified torque in the sequence shown.

Step 1 : 7,4 N·m
Step 2 : 26 N·m

: Engine front

Install intake manifold collector and tighten intake manifold collector bolts and nuts in the order as shown.

Intake manifold collector nuts and bolts : 11 N·m

Install electric throttle control actuator and tighten electric throttle control actuator bolts to the specified torque in the sequence shown.

Rotate crankshaft pulley in normal direction (clockwise when viewed from front) to confirm it turns smoothly.

Installation of the remaining components is in the reverse order of removal.

  • Perform the ″Throttle Valve Closed Position Learning″ when harness connector of the electric throttle control actuator is disconnected. Refer to Description.

  • Perform the ″Idle Air Volume Learning″ when the electric throttle control actuator is replaced. Refer to Description.

INSPECTION AFTER INSTALLATION

  • Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required quantity, fill to the specified level. Refer to Fluids and Lubricants (FOR USA AND CANADA) or Fluids and Lubricants (FOR MEXICO).

  • Use procedure below to check for fuel leakage.

  • Place ignition switch in the "ON" position (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leakage at connection points.

  • Start engine. With engine speed increased, check again for fuel leakage at connection points.

  • Run engine to check for unusual noise and vibration.

  • Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gas, or any oils/fluids including engine oil and engine coolant.

  • Bleed air from passages in lines and hoses, such as in cooling system.

  • After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to specified level, if necessary.

  • Summary of the inspection items:

    ItemBefore starting engineEngine runningAfter engine stopped
    Engine coolant Level Leakage Level
    Engine oil Level Leakage Level
    Transmission/transaxle fluid A/T and CVT Models Leakage Level/Leakage Leakage
    M/T Models Level/Leakage Leakage Level/Leakage
    Other oils and fluids* Level Leakage Level
    Fuel Leakage Leakage Leakage
    Exhaust gas — Leakage —

    *Power steering fluid, brake fluid, etc.