Vq35dd :: Removal and Installation
- Engine Room Cover
- Air Cleaner and Air Duct
- Intake Manifold Collector
- Exhaust Manifold and Three Way Catalyst ➤
- Oil Pan ➤
- Intake Manifold
- Ignition Coil
- Rocker Cover ➤
- High Pressure Fuel Pump and Fuel Hose
- Fuel Injector and Fuel Tube ➤
- Valve Timing Control ➤
- Front Timing Chain Case ➤
- Timing Chain ➤
- Rear Timing Chain Case ➤
- Camshaft ➤
- Oil Seal
- Cylinder Head ➤
- Engine Mount
- Drive Plate
Engine Room Cover Nissan Pathfinder SUV
Exploded View

| 1. | Engine room cover | 2. | Rocker cover (bank 2) | 3. | Intake manifold collector |
Removal and Installation
REMOVAL
Remove front air duct. Refer to Removal and Installation.
Lift up on engine room cover to disengage clips.
Remove engine room cover.
INSTALLATION
Installation is in the reverse order of removal.
Air Cleaner and Air Duct Nissan Pathfinder 2022
Exploded View

| 1. | Air duct hose and resonator assembly | 2. | Front air duct | 3. | Grommet |
| 4. | Air cleaner case mounting bracket | 5. | Bracket | 6. | Retainer |
| 7. | Mounting rubber | 8. | Air cleaner case (lower) | 9. | Air cleaner assembly |
| 10. | Air cleaner filter | 11. | Air cleaner case (upper) | A. | To electric throttle control actuator. Refer to Exploded View. |
| B. | To rocker cover (bank 1). Refer to Exploded View. |
Removal and Installation
REMOVAL
Remove front air duct.
Disconnect the tube clamp at the electric throttle control actuator and at the air duct hose and resonator assembly.
Disconnect the blow-by hose from air duct hose and resonator assembly.
Remove air duct hose and resonator assembly.
Disconnect the harness connector from mass air flow sensor and release harness retainer from air cleaner case (upper).
Release clips and remove the air cleaner case (upper).
Remove bolt and remove the air cleaner case (lower) and air cleaner filter.
Remove mass air flow sensor from air cleaner case (upper) (if necessary).
Do not shock it.
Do not disassemble it.
Do not touch its sensor.
Remove air cleaner filter from air cleaner case (lower) (if necessary).
INSPECTION AFTER REMOVAL
Inspect air cleaner case (upper), air cleaner case (lower), front air duct, air duct and resonator assembly for cracks or tears. Replace as necessary.
INSTALLATION
Installation is in the reverse order of removal.
Intake Manifold Collector Nissan Pathfinder SUV
Exploded View

| 1. | VIAS control solenoid valve | 2. | Vacuum hose 1 | 3. | VIAS control solenoid valve bracket |
| 4. | Vacuum hose 2 | 5. | Intake manifold collector | 6. | Intake manifold collector gasket |
| 7. | Harness bracket | 8. | Electronic throttle control actuator | 9. | Electronic throttle control actuator gasket |
| 10. | Vacuum tube assembly | 11. | Vacuum hose 3 | A. | To power valve actuator 1. Refer to Component Parts Location. |
| B. | To electronic controlled engine mount control solenoid valve. Refer to Component Parts Location. | C. | Refer to Removal and Installation. | D. | Power valve actuator 1 |
| E. | Refer to Removal and Installation. | F. | To engine mount (FR). Refer to Exploded View. | G. | To power valve actuator 2. Refer to Component Parts Location. |
Removal and Installation
REMOVAL
Disconnect the negative battery terminal. Refer to Battery Disconnect.
Remove the cowl top cover and the cowl top extension. Refer to Removal and Installation.
Remove engine room cover (if equipped). Refer to Removal and Installation.
Remove the air cleaner case (upper), air cleaner case (lower), and air duct and resonator assembly. Refer to Removal and Installation.
Disconnect the engine mount (FR) vacuum hose, brake booster vacuum hose and electronic controlled engine mount control solenoid valve vacuum hoses from intake manifold collector.
Disconnect the harness connector from electronic controlled engine mount control solenoid valve. Refer to Component Parts Location.
Disconnect the engine mount insulator (front) vacuum hose.
Disconnect the harness connector from VIAS control solenoid valve 1 and VIAS control solenoid valve 2.
Disconnect the PCV hose from intake manifold collector.
Disconnect the EVAP canister purge volume control solenoid valve hose.
Disconnect the harness connector from electronic throttle control actuator and remove retainer from harness bracket.
Loosen bolts in reverse of the sequence shown and remove the electric throttle control actuator (if necessary).

Remove the VIAS control solenoid valve (if necessary).
Remove the EVAP canister purge volume control solenoid valve. Refer to Exploded View.
Loosen the intake manifold collector bolts and nuts in reverse of the sequence shown and then remove the intake manifold collector and gasket.

INSTALLATION
Installation is in the reverse order of removal.
Tighten intake manifold collector bolts and nuts in the order as shown.

Bolts and nuts : 11 N·m Tighten electric throttle control actuator bolts in the order shown.

Bolts : 8,4 N·m
Perform the ″Throttle Valve Closed Position Learning″ when harness connector of the electric throttle control actuator is disconnected. Refer to Description.
Perform the ″Idle Air Volume Learning″ when the electric throttle control actuator is replaced. Refer to Description.
Exhaust Manifold and Three Way Catalyst ➤ Nissan Pathfinder R53
Oil Pan ➤ Nissan Pathfinder
Intake Manifold Nissan Pathfinder 5th Gen
Exploded View

| 1. | Intake manifold | 2. | Intake manifold gasket | 3. | Insulator |
| A. | Refer to INSTALLATION. |
Removal and Installation
REMOVAL
Remove intake manifold collector. Refer to Removal and Installation.
Loosen intake manifold nuts and bolts in reverse of the sequence shown.

| : Engine front |
Remove intake manifold and intake manifold gasket.
Remove intake manifold studs (if necessary).
INSPECTION AFTER REMOVAL
Surface Distortion
Using suitable tool (A) and suitable tool (B), inspect the surface distortion of the intake manifold. Refer to Intake Manifold.

Standard : 0.1 mm (0.004 in)
INSTALLATION
Installation is in the reverse order of removal.
Install intake manifold studs (if removed) and tighten to specification.
Intake manifold studs : 10,8 N·m Install intake manifold bolts and nuts and tighten to the specified torque in the sequence shown.

Step 1 : 7,4 N·m Step 2 : 26 N·m 
: Engine front
Ignition Coil Nissan Pathfinder Fifth generation
Exploded View

| 1. | Ignition coil | 2. | Spark plug | 3. | Rocker cover (Bank 1) |
| 4. | Rocker cover (Bank 2) |
Removal and Installation (Bank 2)
REMOVAL
Remove engine room cover. Refer to Removal and Installation.
Disconnect the harness connector from ignition coil.
Remove the ignition coil.
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation (Bank 1)
REMOVAL
Remove the intake manifold collector. Refer to Removal and Installation.
Disconnect the harness connector from ignition coil.
Remove the ignition coil.
INSTALLATION
Installation is in the reverse order of removal.
Rocker Cover ➤ Nissan Pathfinder
High Pressure Fuel Pump and Fuel Hose Nissan Pathfinder 2026
Exploded View

| 1. | Fuel rail pressure sensor | 2. | Fuel rail (bank 1) | 3. | High pressure fuel tube (pump side) |
| 4. | High pressure fuel tube (bank side) | 5. | Lifter | 6. | O-ring |
| 7. | High pressure fuel pump | 8. | High pressure fuel pump insulator | 9. | Seal ring |
| 10. | Injector | 11. | Backup ring | 12. | O-ring (green) |
| 13. | Injector holder | 14. | Fuel rail (bank 2) | A. | Refer to Removal and Installation. |
| B. | To fuel feed hose | C. | To camshaft bracket no. 1. Refer to Exploded View. | D. | Refer to Removal and Installation. |
| Engine front |
Removal and Installation
REMOVAL
Release fuel pressure. Refer to Work Procedure.
Remove intake manifold. Refer to Removal and Installation.
Remove bolts (A) and remove high pressure fuel pump cover (1).

Remove high pressure fuel pump insulator.
Release clip (A) and disconnect fuel feed hose (1) from high pressure fuel pump (2).

Disengage fuel feed hose from clip and reposition.
Remove insulator. Refer to Exploded View.
Remove high pressure fuel tube (pump side).
Disconnect harness connector from high pressure fuel pump.
Remove high pressure fuel pump bolts while alternating sides frequently and remove high pressure fuel pump and lifter.
INSTALLATION
Install O-ring to high pressure fuel pump.
Rotate engine clockwise and visually check for bottom dead center of high pressure fuel pump lobe on camshaft.
Apply clean engine oil to high pressure fuel pump bore.
When installing lifter, note the orientation of lifter protrusion (B) and cutout in No. 1 camshaft bracket [bank 2 (A)] should be aligned.

Install high pressure fuel pump and tighten the bolts using the following procedure:
Tighten bolts one revolution while alternating sides until high pressure fuel pump is mated to No. 1 camshaft bracket. Tighten bolts to the specified torque.| High pressure fuel pump bolts | : 26 N·m |
Connect harness connector to high pressure fuel pump.
Install high pressure fuel tube (pump side) using the following procedure:
Install high pressure fuel tube [pump side (2)] and hand tighten flare nut (A) and flare nut (C) until contact seat.
| (1) | : High pressure fuel tube (bank side) |
| (D) | : High pressure fuel tube (bank side) flare nut |
| (E) | : High pressure fuel tube (bank side) flare nut |
| Flare nut | : 15 N·m |
| Flare nut | : 23 N·m |
| Bolt | : 13,5 N·m |
Installation of the remaining components is in the reverse order of removal.
Check for fuel leaks. Refer to Inspection.
Tighten high pressure fuel pump cover bolts to the specified torque in the sequence shown.

High pressure fuel pump cover bolts : 11 N·m 
: Engine front
Inspection
Check for Fuel Leaks
Place ignition switch in the “ON” position (with the engine stopped). With fuel pressure applied to fuel piping, check that there is no fuel leaks at connection points.
Start the engine. With engine speed increased, check again that there is no fuel leaks at connection points.
Fuel Injector and Fuel Tube ➤ Nissan Pathfinder Fifth generation
Valve Timing Control ➤ Nissan Pathfinder R53
Front Timing Chain Case ➤ Nissan Pathfinder R53
Timing Chain ➤ Nissan Pathfinder
Rear Timing Chain Case ➤ Nissan Pathfinder 5th Gen
Camshaft ➤ Nissan Pathfinder R53
Oil Seal Nissan Pathfinder 2026
Removal and Installation of Valve Oil Seal
REMOVAL
Turn crankshaft until the cylinder requiring new oil seals is at TDC. This will prevent valve from dropping into cylinder.
Remove camshaft relating to valve oil seal to be removed. Refer to Removal and Installation.
Remove valve lifters. Refer to Disassembly and Assembly.
Compress the valve spring with suitable tool (A), (B) and (C) and remove the valve collet with a suitable magnetic tool.

Remove valve oil seal using suitable tool (A).

INSTALLATION
Apply new engine oil to new valve oil seal joint surface and seal lip.
Press in valve oil seal to height (H) using suitable tool (A) to specified height.

| Intake and exhaust (H) | : Refer to Cylinder Head. |
Installation of the remaining components is in the reverse order of removal.
Removal and Installation of Front Oil Seal
REMOVAL
Remove drive belt. Refer to Removal and Installation.
Secure the crankshaft pulley using a suitable tool.
Remove the crankshaft pulley as follows:Loosen crankshaft pulley bolt and locate bolt seating surface at 10 mm (0.39 in) from its original position. Position a pulley puller at recess hole of crankshaft pulley to remove crankshaft pulley.

Remove front oil seal from front cover using a suitable tool.

INSTALLATION
Apply new engine oil to new oil seal and install.
Install new oil seal in the direction as shown.

(A) : Dust seal lip (B) : Oil seal lip 
: Engine outside 
: Engine inside
Press-fit oil seal until it becomes flush with the timing chain case end face, using suitable tool (A).

Make sure the garter spring in the oil seal is in position and seal lip is not inverted.
Install crankshaft pulley and tighten the bolt using the following procedure:
Apply a suitable anti-seize lubricant to the crankshaft pulley bolt flange and crankshaft pulley bolt threads.
Secure the crankshaft pulley using a suitable tool.
Tighten crankshaft pulley bolt to the specified torque and then specified angle using Tool.
| Step 1 | : 90 N·m |
| Step 2 | : 84° - 90° degrees clockwise |
| Tool number | : KV10112100 (BT-8653-A) |
Installation of the remaining components is in the reverse order of removal.
Removal and Installation of Rear Oil Seal
REMOVAL
Remove the upper oil pan. Refer to Removal and Installation (Upper Oil Pan).
Remove rear oil seal retainer using Tool.
| Tool Number | : KV10111100 (NI-37228) |
INSTALLATION
Remove old liquid gasket material from mating surface of cylinder block and oil pan using a suitable scraper.
Install the rear oil seal retainer using Tool (A).

| Tool number (A) | : — (NI-47128) |

Use Genuine Silicone RTV Sealant or equivalent. Refer to Recommended Chemical Products and Sealants.
Lubricate the sealing surface of the new rear main seal with new engine oil. Slide the new rear main seal (1) over the Tool (A) and onto the crankshaft.
| Rear oil seal retainer bolts | : 8,8 N·m |
Installation of the remaining components is in the reverse order of removal.
Cylinder Head ➤ Nissan Pathfinder
Engine Mount Nissan Pathfinder 5th Gen
Engine Mount (front)
Removal and Installation
REMOVAL
Remove the air cleaner case (upper), air cleaner case (lower), front air duct, and air duct hose and resonator assembly. Refer to Removal and Installation.
Remove the battery and battery tray assembly. Refer to Removal and Installation.
Remove the front under cover. Refer to Removal and Installation.
Remove the front fender protector side covers (RH/LH). Refer to Exploded View.
Partially remove the fender protectors (RH/LH). Refer to Exploded View.
Remove the radiator assembly. Refer to Removal and Installation.
Remove the engine cooling fan shroud and motor assembly. Refer to Removal and Installation.
Remove the exhaust manifold heat shield (LH). Refer to Exploded View.
Support the engine with a suitable tool.
Disconnect the engine mount insulator (front) vacuum hose.
Remove the engine mount insulator (front) nut (A).

Loosen the engine mount bracket (front) bolts in reverse of the order shown.

| : Engine front |
Remove the engine mount bracket (front).
Remove the engine mount insulator (front) bolts in the reverse order as shown.

| : Front |
Remove the engine mount insulator (front).

INSTALLATION
Install the engine mount insulator (front).

Install the engine mount insulator (front) bolts and tighten to specification in the order shown.

| : Front |
| Engine mount insulator (front) bolts | : 62 N·m |
Install the engine mount bracket (front) to the engine block.
Tighten the engine mount bracket (front) bolts to specification in the order shown.

| : Engine front |
| Engine mount bracket (front) bolts | : 62 N·m |
Install the engine mount insulator (front) nut (A) and tighten to specification.

| Engine mount insulator (front) nut | : 105 N·m |
Installation of the remaining components is in the reverse order of removal.
Drive Plate Nissan Pathfinder
Removal and Installation
For exploded view, refer to Exploded View.
REMOVAL
Remove the engine and transmission assembly and separate the engine from the transmission. Refer to Removal and Installation.
Remove the drive plate using the following procedure:Before removing the drive plate, inspect the drive plate runout is within specification. Refer to Inspection. Secure the crankshaft pulley (1) with a suitable tool (A).

INSTALLATION
Install the drive plate and drive plate reinforcement.
Hand tighten drive plate bolts in a diagonal pattern over several steps.
Secure the crankshaft pulley with a suitable tool, then and tighten drive plate bolts in a diagonal pattern over several steps.
Installation of the remaining components is in the reverse order of removal.
Inspection
Use a suitable tool to measure the runout (Total Indicator Reading) on torque converter mating surface (A).

| Drive plate torque converter surface | : Refer to Drive Plate. |
| Ring gear | : Refer to Drive Plate. |