Removal and Installation - Fuel Injector and Fuel Tube ++
Exploded View

| 1. | Fuel rail pressure sensor | 2. | Fuel rail (bank 1) | 3. | High pressure fuel tube (pump side) |
| 4. | High pressure fuel tube (bank side) | 5. | Lifter | 6. | O-ring |
| 7. | High pressure fuel pump | 8. | High pressure fuel pump insulator | 9. | Seal ring |
| 10. | Injector | 11. | Backup ring | 12. | O-ring (green) |
| 13. | Injector holder | 14. | Fuel rail (bank 2) | A. | Refer to Removal and Installation. |
| B. | To fuel feed hose | C. | To camshaft bracket no. 1. Refer to Exploded View. | D. | Refer to Removal and Installation |
| Engine front |
Removal and Installation
REMOVAL
Release fuel pressure. Refer to Work Procedure.
Remove intake manifold. Refer to Removal and Installation.
Remove bolts (A) and remove high pressure fuel pump cover (1).

Remove high pressure fuel pump insulator.
Release clip (A) and disconnect fuel feed hose (1) from high pressure fuel pump (2).

Release fuel feed hose from clip and reposition.
Remove insulator. Refer to Exploded View.
Remove high pressure fuel tube (pump side) and high pressure fuel tube (bank side).
Disconnect harness connectors from fuel injectors and remove fuel injector harness.
Disconnect the harness connector from the fuel rail pressure sensor.
Remove fuel rail pressure sensor from fuel rail (bank 1) (if necessary).
Remove fuel rail (bank 1) or fuel rail (bank 2) nuts and bolts in reverse of the sequence shown.

| : Engine front |
Remove fuel injector holders from fuel rail (bank 1) or fuel rail (bank 2).
Remove fuel rail (bank 1) or fuel rail (bank 2).
Remove fuel injectors from cylinder head using the following procedure:Install Tool onto fuel injector.
Make sure Tool is installed so it pulls from shaded region (A) of fuel injector.

| Tool number | : — (NI-50366) |

| Tool number | : — (NI-50366) |
Cut seal ring (1) while pinching it. Be careful not to damage injector.

INSTALLATION
Install seal ring to fuel injector using the following procedure:
Install Tool (A) onto fuel injector (1).
| Tool number (A) | : KV10119720 (NI-50364) |

| Tool number (A) | : KV10119730 (NI-50364) |


| Tool number (A) | : KV10119710 (NI-50364) |
| : Injector side |
Install O-ring and backup ring to fuel injector.
Install fuel injector (5) to fuel rail (1) using the following procedure:

Insert it while matching it to the axial center.
Insert so that protrusion (B) of fuel injector is aligned to cutout (A).
Check that protrusions of fuel injectors and fuel rail are aligned with cutouts of clips after installation.
- : O-ring (green)
- : Backup ring
Install fuel rail and fuel injector assembly to cylinder head.
Tighten bolts and nuts in two steps in the sequence shown.

Step 1 : 10 N·m Step 2 : 22 N·m 
: Engine front
Install fuel rail pressure sensor using the following procedure (if necessary):
Apply engine oil to the entire perimeter of the fuel pressure sensor threads. Hand tighten fuel rail pressure sensor. Tighten fuel pressure sensor to the specified torque.| Fuel rail pressure sensor | : 10 N·m |
| Angle | : 35° ± 5° |
| Tool number | : KV10112100 (BT-8653-A) |
Install high pressure fuel tube (pump side) and high pressure fuel tube (bank side) using the following procedure:
Install high pressure fuel tube [pump side (2)] and hand tighten flare nut (A) and flare nut (C) until contact seat.
| Flare nut | : 15 N·m |
| Flare nut | : 23 N·m |
| Bolt | : 13,5 N·m |
| Flare nut | : 15 N·m |
| Flare nut | : 23 N·m |
Installation of the remaining components is in the reverse order of removal.
If fuel injectors are replaced, perform "IDLE AIR VOLUME LEARNING". Refer to Description.
Check for fuel leaks. Refer to Inspection.
Tighten high pressure fuel pump cover bolts to the specified torque in the sequence shown.

High pressure fuel pump cover bolts : 11 N·m 
: Engine front
Inspection
Check for Fuel Leaks
Place ignition switch in the “ON” position (with the engine stopped). With fuel pressure applied to fuel piping, check that there is no fuel leaks at connection points.
Start the engine. With engine speed increased, check again that there is no fuel leaks at connection points.