Removal and Installation - Cylinder Head ++
Exploded View

| 1. | Cylinder head (bank 2) | 2. | Cylinder head (bank 1) | 3. | Cylinder head (bank 1) gasket |
| 4. | Cylinder block | 5. | Cylinder head (bank 2) gasket | A. | Refer to Removal and Installation. |
Removal and Installation
REMOVAL
Remove the intake and exhaust camshafts. Refer to Removal and Installation.
If removing the cylinder head (bank 2), remove the exhaust manifold and three way catalyst (bank 2) using the following procedure:Disconnect the harness connector from the air fuel ratio (A/F) sensor (bank 2) and release the harness from retainer. Remove the air fuel ratio (A/F) sensor 1 (bank 2) using Tool. Refer to Exploded View.
Discard any air fuel ratio (A/F) 1 sensor (bank 2) which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard surface such as a concrete floor; replace with a new sensor.
| Tool | : KV991J0050 (NI-44626) |

| (A) | : Bank 2 |
| (B) | : Bank 1 |
| : Engine front |
If removing the cylinder head (bank 1), remove the exhaust manifold and three way catalyst (bank 1) using the following procedure:Disconnect the harness connector from the air fuel ratio (A/F) sensor 1 (bank 1) and remove harness from retainer. Remove exhaust manifold (bank 1) cover. Refer to Exploded View. Disconnect the harness connector from the heated oxygen sensor 2 (bank 1) and remove harness from retainers. Remove bolt securing support bracket (bank 1) to the support bearing bracket. Refer to Exploded View. Remove the exhaust manifold and three way catalyst (bank 1) nuts in reverse of the sequence shown and remove the exhaust manifold and three way catalyst (bank 1).

| (A) | : Bank 2 |
| (B) | : Bank 1 |
| : Engine front |
Remove heater pipe. Refer to Exploded View.
Disconnect the harness connector from the engine coolant temperature sensor.
Remove water outlet. Refer to Exploded View.
Remove the bank 1 and bank 2 cylinder head bolts with a suitable tool.
The bolts should be loosened gradually in three stages.
Loosen the bolts in the numerical order as shown.
Bank 1


: Engine front Bank 2


: Engine front
Remove cylinder heads and gaskets.
INSTALLATION
Turn the crankshaft until No. 1 piston is set at TDC on the compression stroke.

The crankshaft key (1) should line up with the bank 1 cylinder center line (A) as shown.
Install new cylinder head gaskets.
Inspect the cylinder head bolts before installing the cylinder heads.

| Limit (d1 - d2) | : 0.11 mm (0.0043 in) |
| (A) | : d1 location |
| (B) | : d2 location |
| (C) | : 48 mm (1.89 in) |
| (D) | : 11 mm (0.43 in) |
Lubricate threads and seat surfaces of the bolts with new engine oil.
Install the cylinder heads on the cylinder block. Tighten the cylinder head bolts to the specified torque and specified angle in the sequence shown using Tool.
| Tool number | : KV10112100 (BT-8653-A) |
Tightening procedure:
| Cylinder head bolts | |
| Step 1 | : Tighten 98 N·m |
| Step 2 | : Loosen in the reverse order of tightening to 0 N·m |
| Step 3 | : Tighten 39 N·m |
| Step 4 | : Tighten 103° - 108° degrees |
| Step 5 | : Tighten 103° - 108° degrees |
Bank 1


: Engine front Bank 2


: Engine front
If removed, install the exhaust manifold and three way catalyst (bank 2) using the following procedure:Install the exhaust manifold gasket in the direction shown.

| (A) | : Bank 1 |
| (B) | : Triangle press |
| (C) | : Bank 2 |
| : Engine front |

| Exhaust manifold nut | : 31 N·m |
| (A) | : Bank 2 |
| (B) | : Bank 1 |
| : Engine front |
If removed, install the exhaust manifold and three way catalyst (bank 1) using the following procedure:Install the exhaust manifold gasket in the direction shown.

| (A) | : Bank 1 |
| (B) | : Triangle press |
| (C) | : Bank 2 |
| : Engine front |

| Exhaust manifold (bank 1) nuts | : 31 N·m |
| (A) | : Bank 2 |
| (B) | : Bank 1 |
| : Engine front |
Install the intake manifold gaskets.
Installation of the remaining components is in the reverse order of removal.
Disassembly and Assembly

| 1. | Lifter | 2. | Valve collet | 3. | Valve spring retainer |
| 4. | Valve oil seal | 5. | Valve spring | 6. | Valve spring seat |
| 7. | Valve guide (INT) | 8. | Valve guide (EXH) | 9. | Cylinder head (bank 1) |
| 10. | Valve seat (EXH) | 11. | Valve seat (INT) | 12. | Valve (INT) |
| 13. | Valve (EXH) | 14. | Cylinder head (bank 2) | 15. | Spark plug tube |
| A. | Refer to ASSEMBLY |
: Identify installation position of valve lifters and store without mixing them up.
DISASSEMBLY
Remove spark plug. Refer to Exploded View.
Remove valve lifter.
Identify installation positions and store them without mixing them up.
Remove valve collet.

Compress the valve spring with suitable tool (A), (B) and (C) and remove the valve collet with a suitable magnetic tool.
Remove valve spring retainer, valve spring and valve spring seat.
Push valve stem to combustion chamber side and remove valve.
Identify installation positions, and store them without mixing them up.
Remove valve oil seals using suitable tool (A).

Remove valve seat (if necessary). Refer to Inspection After Disassembly.
Remove valve guide (if necessary). Refer to Inspection After Disassembly.
Remove spark plug tube (if necessary).
Using pair of pliers, pull spark plug tube out of cylinder head.
ASSEMBLY
Install valve guide (if removed). Refer to Inspection After Disassembly.
Install valve seat (if removed). Refer to Inspection After Disassembly.
Install valve oil seals using suitable tool (A).

| Height (H) (Without valve spring seat installed) | ||
| Intake and exhaust | : Refer to Cylinder Head. | |
Install valve spring seat.
Install valves.
Install it in the original position.
Install valve spring.
Install valve spring so that the identification color (A) is facing upward.
Install smaller pitch to cylinder head side (B).
Intake and exhaust valve springs are the same.

Install valve spring retainer.
Install valve collet.

Compress valve spring using suitable tool (A) attachment (B) and adapter (C). Install valve collet with magnet hand.
Tap valve stem edge lightly with plastic hammer after installation to check its installed condition.
Install valve lifter.
Install it in the original position.
Install spark plug tube (If removed).
Press-fit spark plug tube as follows:
Use Genuine High Strength Locking Sealant or equivalent. Refer to Recommended Chemical Products and Sealants.
Press-fit spark plug tube so that its height (A) is as specified in using suitable tool.
| Press-fit height (A) | : 37.7 - 39.1 (1.484 - 1.539 in) |
| (B) | : Locking sealant application area |
Install spark plug. Refer to Exploded View.
Inspection After Disassembly
CYLINDER HEAD DISTORTION
Clean the surface of the cylinder head. Use a reliable straightedge and feeler gauge to check the flatness of cylinder head surface.
Check along six positions as shown.

| Head surface distortion | |
| Standard and Limit | : Refer to Cylinder Head. |
If it exceeds the limit, replace the cylinder head.
The limit for cylinder head resurfacing is determined by the cylinder block resurfacing.
| Resurfacing Limit | |
| Amount of cylinder head resurfacing is (A). | |
| Amount of cylinder block resurfacing is (B). | |
| The maximum limit | : A + B = 0.2 mm (0.008 in) |
After resurfacing cylinder head, check that camshaft rotates freely by hand. If resistance is felt, cylinder head must be replaced.
| Nominal cylinder head height | : Refer to Cylinder Head. |
VALVE GUIDE CLEARANCE
Measure diameter of valve stem using suitable tool (B) as shown.

| Standard | : Refer to Cylinder Head. |
Measure the inner diameter of valve guide using suitable tool (A).
| Standard | : Refer to Cylinder Head. |
(Valve guide clearance) = (Valve guide inner diameter) – (Valve stem diameter).
| Standard | : Refer to Cylinder Head. |
If the calculated value exceeds the limit, replace valve and/or valve guide.
VALVE GUIDE REPLACEMENT
When valve guide is removed, replace with oversized [0.2 mm (0.008 in)] valve guide.
To remove valve guide, heat cylinder head to 110 - 130 °C by soaking in heated oil.

Drive out the valve guide with a press [under a 20 kN (2.2 US ton) pressure] or hammer and suitable tool.

Ream cylinder head valve guide hole using suitable tool (A).

| Standard | : Refer to Cylinder Head. |
Heat cylinder head to 110 - 130 °C by soaking in heated oil and press valve guide from camshaft side to the dimensions as shown using suitable tool.

| Standard | : Refer to Cylinder Head. |
Apply reamer finish to valve guide using suitable tool (A).

| Standard | : Refer to Cylinder Head. |
VALVE SEAT CONTACT
After confirming that the dimensions of valve guides and valves are within specifications, perform this procedure.

(A) : OK (B) : NG
Apply prussian blue onto contacting surface of valve seat to check the condition of the valve contact on the surface.
Check if the contact area band is continuous all around the circumference.
If not, grind to adjust valve fitting and check again. If the contacting surface still has NG conditions even after the re-check, replace valve seat.
VALVE SEAT REPLACEMENT
Bore out old seat until it collapses. Boring should not continue beyond the bottom face of the seat recess in cylinder head. Set the machine depth stop to ensure this. Refer to Cylinder Head.
Ream cylinder head (1) recess diameter for service valve seat (2).

| Standard | Refer to Cylinder Head. |
Be sure to ream in circles concentric to the valve guide center.
This will enable valve seat to fit correctly.
Heat cylinder head to 110 - 130 °C by soaking in heated oil.

Press fit valve seat until it seats on the bottom.
Finish seat to the specified dimensions using suitable tool. Refer to Cylinder Head.

| Seat face angle (α) | Refer to Cylinder Head. |
| Contacting width (W) for intake | |
| Contacting width (W) for exhaust |
VALVE SPRING SQUARENESS
Set a suitable tool (D) along the side of valve spring and rotate spring. Measure the maximum clearance (A) between the top of spring and suitable tool.

| (B) | : Suitable tool |
| (C) | : Contact area |
| Limit | : Refer to Cylinder Head. |
VALVE SPRING DIMENSIONS AND VALVE SPRING PRESSURE LOAD
Check valve spring pressure at specified spring height.

| Standard | : Refer to Cylinder Head. |
| Limit | : Refer to Cylinder Head. |
If it is not within specifications, replace the spring.