Removal and Installation - Rocker Cover ++
Exploded View

| 1. | Camshaft position sensor (Bank 2) | 2. | O-ring | 3. | Camshaft position sensor (Bank 1) |
| 4. | O-ring | 5. | Rocker cover (Bank 1) | 6. | Clamp |
| 7. | Blow-by hose | 8. | Breather hose | 9. | Rocker cover gasket (Bank 1) |
| 10. | Rocker cover gasket (Bank 2) | 11. | Rocker cover (Bank 2) | A. | Refer to Removal and Installation (Bank 2) (Bank 2) or Removal and Installation (Bank 1) (Bank 1). |
| B. | To air duct hose and resonator assembly. Refer to Exploded View. | Engine front |
Removal and Installation (Bank 2)
REMOVAL
Release fuel pressure. Refer to Work Procedure.
Remove high pressure fuel pump. Refer to Removal and Installation.
Remove bolts (A) and reposition bracket (1) away from rocker cover (bank 2).

Disconnect the harness connectors from exhaust camshaft position sensor (bank 2) and intake camshaft position sensor (bank 2).
Remove exhaust camshaft position sensor (bank 2) and intake camshaft position sensor (bank 2).

Remove ignition coils. Refer to Exploded View.
Remove rocker cover bolts in reverse of the sequence shown and remove rocker cover (bank 2).

Remove oil filler cap from rocker cover (bank 2) (if necessary).
Disengage clamp and remove blow-by hose from rocker cover (bank 2) (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
Blow-by hose clamps should be installed facing upwards.
Install press fit hoses so that the white mark faces the rib of the connector.
Apply a 3 mm (0.12 mm) bead of sealant to the areas on the front corners using a suitable tool.

Use Genuine Silicone RTV Sealant or equivalent. Refer to Recommended Chemical Products and Sealants.
(1) : Camshaft bracket (2) : Cylinder head (A) : 4 mm (0.16 in) (B) : 5 mm (0.20 in) (C) : 4 mm (0.16 in) (E) : 10 mm (0.39 in) Tighten the rocker cover bolts to the specified torque in the sequence shown.

Rocker cover bolts Step 1 : 2 N·m Step 2 : 8,3 N·m
Removal and Installation (Bank 1)
REMOVAL
Remove the front air duct and air duct hose and resonator assembly. Refer to Removal and Installation.
Remove the intake manifold collector. Refer to Removal and Installation.
Disconnect the harness connectors from exhaust camshaft position sensor (bank 1) and intake camshaft position sensor (bank 1).
Remove exhaust camshaft position sensor (bank 1) and intake camshaft position sensor (bank 1).

Remove the breather hose from the rocker cover (bank 1).
Remove ignition coils. Refer to Exploded View.
Remove rocker cover bolts in reverse of the sequence shown.

| : Engine front |
Remove the rocker cover (bank 1) and rocker cover (bank 1) gasket.
INSTALLATION
Installation is in the reverse order of removal.
Blow-by hose clamps should be installed facing upwards.
Install press fit hoses so that the white mark faces the rib of the connector.
Apply a 3 mm (0.12 mm) bead of sealant to the areas on the front corners using a suitable tool.

Use Genuine Silicone RTV Sealant or equivalent. Refer to Recommended Chemical Products and Sealants.
(1) : Camshaft bracket (2) : Cylinder head (A) : 4 mm (0.16 in) (B) : 5 mm (0.20 in) (C) : 4 mm (0.16 in) (E) : 10 mm (0.39 in) Tighten the rocker cover bolts to the specified torque in the sequence shown.

Rocker cover bolts Step 1 : 2 N·m Step 2 : 8,3 N·m 
: Engine front