Removal and Installation - Timing Chain ++
Exploded View

| 1. | Internal chain guide | 2. | Timing chain (primary) | 3. | Camshaft sprocket (EXH) |
| 4. | Camshaft sprocket (INT) | 5. | Timing chain tensioner (primary) | 6. | Slack guide |
| 7. | Tension guide | 8. | Oil pump drive chain tensioner | 9. | Crankshaft sprocket |
| 10. | Timing chain oil jet | 11. | Timing chain tensioner [secondary (bank 2)] | 12. | Timing chain [secondary (bank 2)] |
| 13. | Timing chain [secondary (bank 1)] | 14. | Timing chain tensioner [secondary (bank 1)] |
Removal and Installation
REMOVAL
Remove front timing chain case. Refer to Removal and Installation.
Remove the timing chain tensioner [primary (1)].Pull lever (C) down and release plunger (D) stopper tab (A). Plunger stopper tab can be pushed up to release (coaxial structure with lever).

| (B) | : Suitable tool |

Remove internal chain guide (1), tension guide (3) and slack guide(2).

Remove timing chain (primary) and crankshaft sprocket.
Remove timing chain (secondary) and camshaft sprockets as follows:Insert a suitable stopper pin into the hole (C) on the bank 2 (A) and bank 1 (B) timing chain tensioners [secondary (1)].

Secure the hexagonal portion of camshaft using a suitable tool to loosen bolts.

Turn camshaft slightly to keep the chain tight when removing the timing chain (secondary).
Insert 0.5 mm (0.020 in) thick metal or resin plate (C) between timing chain and timing chain tensioner plunger [guide (B)]. Remove timing chain (secondary) (2) together with camshaft sprockets with timing chain loose from guide groove.

(1) : Timing chain tensioner (secondary) (A) : Stopper pin
Remove oil pump drive chain and crankshaft sprocket.
Remove bolt and remove oil pump drive chain tensioner.
INSPECTION
Check for cracks and any excessive wear of the timing chain. Replace the timing chain as necessary.
INSTALLATION

| 1. | Internal chain guide | 2. | Camshaft sprocket (INT) | 3. | Timing chain (secondary) |
| 4. | Camshaft sprocket (EXH) | 5. | Timing chain tensioner (primary) | 6. | Slack guide |
| 7. | Timing chain (primary) | 8. | Oil pump drive chain | 9. | Oil pump drive chain tensioner |
| 10. | Crankshaft sprocket | 11. | Water pump | 12. | Tension guide |
| 13. | Crankshaft key | 14. | Timing chain tensioner (secondary) | A. | Mating mark (blue link) |
| B. | Mating mark | C. | Mating mark (circle) | D. | Mating mark (pink link) |
| E. | Mating mark | F. | Mating mark (oblong) |
Check that dowel pin (A) and crankshaft key (1) are located as shown. (No. 1 cylinder at compression TDC)

| Camshaft dowel pin | |
| : At cylinder head upper face side in each bank | |
| Crankshaft key | |
| : At cylinder head side of bank 1 | |
Install timing chain (secondary) and camshaft sprockets (INT and EXH) as follows:
Push plunger of timing chain tensioner (secondary) and keep it pressed in with suitable tool(A).

| (A) | : Bank 2 |
| (B) | : Dowel pin groove |
| (C) | : Pink link |
| (D) | : Bank 1 |
| (E) | : Mating mark (circle on rear face) |
| (F) | : Mating mark (oblong on rear face) |
Align the mating marks on timing chain [secondary (pink link)] with the mating marks on camshaft sprockets (INT and EXH), and install them.
Align dowel pin on camshafts with the groove on sprockets, and install them.
Tighten the bolts for the camshaft sprockets by hand enough to prevent the dowel pins from falling out of the grooves.
It may be difficult to visually check the dislocation of mating marks during and after installation. To make the matching easier, make a mating mark (A) on the top of sprocket teeth and its extended line with paint.

(B) : Mating mark (pink link)
After confirming the mating marks are aligned, tighten the camshaft sprocket bolts.

Secure the camshaft using a suitable tool at the hexagonal portion to tighten the bolts.
Remove stopper pins from timing chain tensioners [secondary (1)].

| (A) | : Bank 1 |
| (B) | : Bank 2 |
| (C) | : Stopper pin |
Install oil pump drive chain tensioner.
Install oil pump drive chain and oil pump drive chain sprocket onto the crankshaft (1).

Install the timing chain (primary).

Install timing chain (primary) so the mating mark (B) on camshaft sprocket (1) is aligned with the blue link (A) on the timing chain, while the mating mark (C) on the crankshaft sprocket (2) is aligned with the pink link (D) on the timing chain, as shown.
When it is difficult to align mating marks of the timing chain (primary) with each sprocket, gradually turn the camshaft using a suitable tool on the hexagonal portion to align it with the mating marks.
During alignment, be careful to prevent dislocation of mating mark alignments of the secondary timing chains.
- : Water pump
Install the internal chain guide (1), slack guide (2) and tension guide (3).


- : Slack guide
- : Cylinder block
Install the timing chain tensioner (primary) with the following procedure:Pull plunger stopper tab (A) up (or turn lever downward) so as to remove plunger stopper tab from the ratchet of plunger (D).

The lever parts and the tab are synchronized. Therefore, the plunger will be secured under this condition.

Remove any dirt and foreign materials completely from the back and the mount surfaces of timing chain tensioner (primary).
Reconfirm that the matching marks on the sprockets and the timing chain have not slipped out of alignment.
Install the front timing chain case. Refer to Removal and Installation.
Installation of the remaining components is in the reverse order of removal.