Removal and Installation - Oil Pan ++
Exploded View

| 1. | O-ring | 2. | Front cover gasket | 3. | Oil cooler gasket |
| 4. | Oil cooler | 5. | Oil cooler connection | 6. | Oil filter |
| 7. | Oil pan (lower) | 8. | Washer | 9. | Drain plug |
| 10. | Engine oil pressure control solenoid valve | 11. | Rear plate cover | 12. | Oil pan (upper) |
| 13. | Crankshaft position sensor (POS) | 14. | O-ring | 15. | Rear oil seal retainer gasket |
| A. | Refer to Removal and Installation. | B. | Refer to Removal and Installation (Upper Oil Pan). | C. | Refer to Removal and Installation (Lower Oil Pan). |
Removal and Installation (Lower Oil Pan)
REMOVAL
Drain the engine oil. Refer to Draining.
Loosen the oil pan (lower) bolts in reverse of the sequence shown.

Remove the oil pan (lower).
After removing the bolts, separate the mating surface and remove the old liquid gasket using Tool (A).

Tap (B) the Tool to insert it.
In areas where the Tool is difficult to use, lightly tap to slide (C) it.
Tool number (A) : KV10111100 (NI-37228)
Remove the old sealant from the bolt holes and threads.
INSPECTION AFTER REMOVAL
Clean debris from the oil strainer.
INSTALLATION
Apply a continuous bead of sealant to the oil pan (lower).

Be sure the sealant is 4.5 - 5.5 mm (0.177 - 0.217 in) wide.
Use Genuine Silicone RTV Sealant, or equivalent. Refer to Recommended Chemical Products and Sealants.
| (A) | : Groove |
| (B) | : Bolt hole |
| : Inside |
Install the oil pan (lower) and tighten the oil pan (lower) bolts to the specified torque in the sequence shown.

| Oil pan (lower) bolts | : 8,8 N·m |
Refill the engine with engine oil. Refer to Refilling.
INSPECTION AFTER INSTALLATION
Inspect the engine oil level. Refer to Inspection.
Start the engine and check for leaks. Refer to Inspection. Repair as necessary.
Removal and Installation (Upper Oil Pan)
REMOVAL
Secure the engine assembly to stand. Refer to Removal and Installation.
Remove the oil dipstick.
Remove the drive belt. Refer to Removal and Installation.
Disconnect the harness connectors from compressor.
Remove the compressor. Refer to Exploded View.
Remove the crankshaft pulley as follows:
Loosen crankshaft pulley bolt and locate bolt seating surface at 10 mm (0.39 in) from its original position.
Position a suitable tool at recess hole of crankshaft pulley to remove crankshaft pulley.

Remove water pipe. Refer to Exploded View.
Disconnect the water hoses from the oil cooler.
Remove the oil filter and oil cooler from the oil pan (upper) (if necessary).
Loosen the oil pan (lower) bolts in reverse of the sequence shown.

Remove the oil pan (lower).
After removing the bolts, separate the mating surface and remove the old liquid gasket using Tool (A).

Tap (B) the Tool to insert it.
In areas where the Tool is difficult to use, lightly tap to slide (C) it.
Tool number (A) : KV10111100 (NI-37228)
Remove the old sealant from the bolt holes and threads.
Disconnect the harness connector from the engine oil pressure control solenoid valve.
Remove bolts (B) and remove engine oil pressure control solenoid valve (2).

Remove bolt (A) and remove oil pump drive chain cover (1).
Rotate oil pump drive chain tensioner (1) counterclockwise with a suitable tool and remove oil pump drive chain (2) from oil pump gear.

Remove the oil pump bolts (A) in reverse of the sequence shown and remove (if necessary).


Remove the oil pan (upper) using the following procedure:
Remove the oil pan (upper) bolts in reverse of the sequence shown.

Insert a suitable tool (B) into the notch (C) of the oil pan [upper (1)] as shown.

Remove the oil pan (upper) by moving the suitable tool up and down (A) as shown.
Remove the O-ring from the bottom of the cylinder block and oil pump housing.
Remove front cover gasket and rear oil seal retainer gasket.
Remove the old sealant from the mating surfaces using a suitable tool (A).

Also remove the old sealant from mating surface of the cylinder block.
Remove the old sealant from the bolt holes and threads.
INSPECTION AFTER REMOVAL
Clean debris from oil strainer.
INSTALLATION
Apply sealant (A) to the front cover gasket and the rear oil seal retainer gasket as shown.

Use Genuine RTV Silicone Sealant or equivalent. Refer to Recommended Chemical Products and Sealants.
| Dimension (B) | : 15 mm (0.59 in) |
| Dimension (C) | : 5 mm (0.20 in) |
Install the front cover gasket (1) and rear oil seal retainer gasket (2) as shown.

| : Engine front |
Apply a bead of sealant to the cylinder block mating surface of the oil pan (upper) as shown.

Be sure the sealant is applied 4.0 - 5.0 mm (0.157 - 0.197 in) as shown. Increase the bead to 4.5 - 5.5 mm (0.177 - 0.217 in) at the locations (A) indicated.
Use Genuine RTV Silicone Sealant, or equivalent. Refer to Recommended Chemical Products and Sealants.

: Engine front
Install new O-ring (1) into the cylinder block before installing oil pan (upper).

- : Crankshaft pulley
Install the oil pan (upper).

Tighten bolts (1) and (2) to specification within five minutes of applying the liquid gasket.
Tighten the remaining oil pan (upper) bolts to specification in the sequence shown.
| Oil pan (upper) bolts | : 22 N·m |
Install the oil pump and new O-rings (1) and tighten oil pump bolts (A) to the specified torque in the sequence shown.

| Oil pump bolts | : 22 N·m |
Apply a continuous bead of sealant to the oil pan (lower).

Be sure the sealant is 4.5 - 5.5 mm (0.177 - 0.217 in) wide.
Use Genuine Silicone RTV Sealant, or equivalent. Refer to Recommended Chemical Products and Sealants.
| (A) | : Groove |
| (B) | : Bolt hole |
| : Inside |
Install the oil pan (lower) and tighten the oil pan (lower) bolts to the specified torque in the sequence shown.

| Oil pan (lower) bolts | : 8,8 N·m |
Installation of the remaining components is in the reverse order of removal.
INSPECTION AFTER INSTALLATION
Before starting engine, check oil/fluid levels including engine coolant and engine oil. If there is less than required quantity, fill to the specified level. Refer to Fluids and Lubricants (FOR USA AND CANADA) or Fluids and Lubricants (FOR MEXICO).
Use procedure below to check for fuel leaks.
Place ignition switch in the "ON" position (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leaks at connection points.
Start engine. With engine speed increased, check again for fuel leaks at connection points.
Run engine to check for unusual noise and vibration.
Warm up engine thoroughly to make sure there are no leaks of fuel, exhaust gas, or any oils/fluids including engine oil and engine coolant.
Bleed air from passages in lines and hoses, such as in cooling system.
After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to specified level, if necessary.
Summary of the inspection items:
Item Before starting engine Engine running After engine stopped Engine coolant Level Leakage Level Engine oil Level Leakage Level Transmission/transaxle fluid A/T and CVT Models Leakage Level/Leakage Leakage M/T Models Level/Leakage Leakage Level/Leakage Other oils and fluids* Level Leakage Level Fuel Leakage Leakage Leakage Exhaust gas — Leakage — *Power steering fluid, brake fluid, etc.