Back Door
Exploded View

| Back door weather-strip | Back door hinge | Back door stay bracket upper LH* | |||
| Back door stay LH* | Back door stay bracket lower LH* | Back door bumper rubber | |||
| Back door panel | TORX bolt | Back door striker | |||
| Back door stay bracket lower RH* | Back door stay RH* | Back door stay bracket upper RH* | |||
| : Center mark | |||||
| : Seam | |||||
| * | : Without automatic back door models. | ||||
| : Always replace after every disassembly. | |||||
| : N·m (kg-m, in-lb) | |||||
| : Body grease | |||||
- Back Door Assembly
- Back Door Striker
- Back Door Hinge
- Back Door Stay
- Back Door Weather-Strip
Back Door Assembly Nissan Ariya 2023
Removal & Installation
REMOVAL
Remove luggage side upper finisher. Refer to Removal & Installation.
Remove headlining assembly. Refer to Removal & Installation.
Disengage left side of Nissan Ariya vehicle harness fixing clip.

| : Clip | |
| : Nissan Ariya Vehicle front |
Disconnect rear washer tube. Refer to Removal & Installation.
Remove grommet LH
from body panel, and then pull out back door harness and rear washer tube from Nissan Ariya vehicle body.

Disconnect right side harness connectors
, and then disengage harness fixing clips.

| : Clip | |
| : Nissan Ariya Vehicle front |
Remove grommet RH
from body panel, and then pull out back door harness from Nissan Ariya vehicle body.

Support back door assembly with the proper material to prevent it from falling.
Remove back door stay from back door stay bracket lower (without automatic back door models). Refer to Removal & Installation.
Remove spindle unit from spindle unit bracket lower (with automatic back door models). Refer to Removal & Installation.
Remove back door hinge mounting bolts, and then remove back door assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
Inspection
Open and close the back door. Check that door hinge rotation portion moves smoothly.
Check back door hinge rotating part for poor lubrication. Apply body grease if necessary.

| : Body grease |
Adjustment
FITTING ADJUSTMENT
Fitting Adjustment Standard Dimension

| Roof panel | Body side outer | Rear bumper fascia | |||
| Back door panel | Back door striker | TORX bolt | |||
| Back door bumper rubber | Back door hinge | ||||
| : Always replace after every disassembly. | |||||
| : N·m (kg-m, ft-lb) | |||||
| : Body grease | |||||
Unit: mm [in]
| Portion | Standard | |||
|---|---|---|---|---|
| Back door panel – Roof panel | H | Clearance | 5.4 – 9.4 [0.213 – 0.370] |
|
| I | Surface height | (−3.3) – (+0.7) [(−0.130) – (+0.028)] |
||
| Back door panel – Body side outer | J | Clearance | 2.5 – 7.1 [0.098 – 0.280] |
|
| K | Surface height | (−1.5) – (+2.5) [(−0.059) – (+0.098)] |
||
| Back door panel – Rear bumper fascia | L | Clearance | 2.6 – 7.0 [0.102 – 0.276] |
|
| M | Surface height | (−3.7) – (−0.3) [(−0.146) – (−0.012)] |
||
| N | Clearance | 5.7 – 9.7 [0.224 – 0.382] |
||
| O | Surface height | (−4.4) – (+0.2) [(−0.173) – (+0.008)] |
||
Check the clearance and the surface height between back door and each part by seeing and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures shown below.
Fitting Adjustment Procedure
Remove back door striker. Refer to Removal & Installation.
Loosen back door hinge mounting bolts.
Temporarily install back door striker.
Adjust the clearance and surface height of back door according to the fitting standard dimension by moving back door panel and back door striker, adjusting bumper rubber.
Turn the stopper part
counterclockwise to unlock.
Adjust by moving the bumper rubber part
up and down.
Turn the stopper part
clockwise to lock.
Tighten back door hinge mounting bolts to the specified torque.
Position back door lock assembly and engage back door striker. Check back door lock assembly and back door striker for looseness.
Tighten back door striker mounting TORX bolts to the specified torque.
Install luggage rear plate mask. Refer to Removal & Installation.
BACK DOOR STRIKER ADJUSTMENT
Adjust back door striker so that it becomes parallel with back door lock insertion direction.
Back Door Striker Nissan Ariya first Gen
Removal & Installation
REMOVAL
Remove luggage rear plate mask. Refer to Removal & Installation.
Remove mounting TORX bolts, and then remove back door striker.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
Back Door Hinge Nissan Ariya 1st generation
Removal & Installation
REMOVAL
Remove back door assembly. Refer to Removal & Installation.
Remove back door hinge mounting nuts, and then remove back door hinge.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
Back Door Stay Nissan Ariya 2023
Removal & Installation
REMOVAL
Support the back door with the suitable material to prevent it from falling.
Remove back door stay bracket upper and lower mounting bolts, and then remove back door stay with back door stay bracket upper and lower.
Disengage back door stay from back door stay bracket lower.Remove metal clip
located on connection between back door stay
and stud ball of back door stay bracket lower
using a remover tool (A) according to the numerical order 1→2 indicated by arrows as shown in the figure.

Repeat the same operation to disengage back door stay from back door stay bracket upper, and then remove back door stay.
INSTALLATION
Install in the reverse order of removal.
Disposal
Fix back door stay
using a vise (C).

Using a hacksaw, slowly make 2 holes in the back door stay according to the numerical order 1→2 as shown in the figure.

| A: | 20.0 mm (0.787 in) |
| Cut at the groove. |
Back Door Weather-Strip Nissan Ariya: FE0
Removal & Installation
REMOVAL
Pull up and remove engagement with body from weather-strip joint.
INSTALLATION
Working from the upper section, align back door weather-strip
center mark
with Nissan Ariya vehicle center position mark
and install weather-strip onto the vehicle
.

Align the seam
of back door weather-strip
with the center
of back door striker
, and then install weather-strip onto the Nissan Ariya vehicle.

Pull back door weather-strip gently to ensure that there is no loose section.