Dtc/circuit Diagnosis

In this manual: Dtc/circuit Diagnosis
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
7989steps
~47934min
5/5difficulty
Done 0 of 7989
  • B14e0-02 Wheel Sensor
  • B14e0-09 Wheel Sensor
  • B14e0-38 Wheel Sensor
  • B14e0-4a Wheel Sensor
  • B14e1-09 Wheel Sensor
  • B14e1-38 Wheel Sensor
  • B14e1-4a Wheel Sensor
  • B14e2-09 Wheel Sensor
  • B14e2-38 Wheel Sensor
  • B14e2-4a Wheel Sensor
  • B14e2-64 Wheel Sensor
  • B14e3-02 Wheel Sensor
  • B14e3-09 Wheel Sensor
  • B14e3-11 Wheel Sensor
  • B14e3-12 Wheel Sensor
  • B14e3-13 Wheel Sensor
  • B14e3-1c Wheel Sensor
  • B14e3-38 Wheel Sensor
  • B14e3-4a Wheel Sensor
  • B14e3-64 Wheel Sensor
  • B14e4-64 Wheel Sensor
  • B14e5-64 Adas Control Unit System
  • B14e5-92 Adas Control Unit System
  • B14e6-85 Brake Control System
  • B14e6-92 Brake Control System
  • C18d0-01 Brake Power Supply Back up Unit
  • C18d1-09 Brake Power Supply Back up Unit
  • C18d2-12 Brake Power Supply Back up Unit
  • C18d3-14 Brake Power Supply Back up Unit
  • C18d4-14 Brake Power Supply Back up Unit
  • C18d5-09 Brake Power Supply Back up Unit
  • C18d6-09 Brake Power Supply Back up Unit
  • C18d7-09 Brake Power Supply Back up Unit
  • C18d8-09 Brake Power Supply Back up Unit
  • C18d9-09 Brake Power Supply Back up Unit
  • C18da-09 Brake Power Supply Back up Unit
  • C18db-09 Brake Power Supply Back up Unit
  • C18dc-09 Brake Power Supply Back up Unit
  • C18dd-09 Brake Power Supply Back up Unit
  • C18de-82 Brake Power Supply Back up Unit
  • C18de-83 Brake Power Supply Back up Unit
  • C18de-87 Brake Power Supply Back up Unit
  • C18e1-04 Motor
  • C18e1-07 Motor
  • C18e1-18 Motor
  • C18e1-19 Motor
  • C18e1-49 Motor
  • C18e1-4b Motor
  • C18e3-86 Abs Actuator and Electric Unit (control Unit) System
  • C18e4-88 Can Comm Circuit
  • C18e5-88 Can Comm Circuit
  • C18e6-49 Can Comm System
  • C18e7-13 Power Supply Circuit
  • C18e7-16 Power Supply Circuit
  • C18e7-17 Power Supply Circuit
  • C18e7-1c Power Supply Circuit
  • C18e9-01 Control Module
  • C18e9-04 Control Module
  • C18e9-44 Control Module
  • C18e9-45 Control Module
  • C18e9-46 Control Module
  • C18e9-47 Control Module
  • C18e9-48 Control Module
  • C18e9-49 Control Module
  • C18e9-96 Control Module
  • C18ea-01 Abs Actuator and Electric Unit (control Unit) System
  • C18eb-01 Brake Power Supply Back up Unit
  • C18ec-01 Stroke Sensor
  • C18ec-04 Stroke Sensor
  • C18ec-11 Stroke Sensor
  • C18ec-12 Stroke Sensor
  • C18ec-13 Stroke Sensor
  • C18ec-14 Stroke Sensor
  • C18ec-15 Stroke Sensor
  • C18ec-1f Stroke Sensor
  • C18ed-04 Motor
  • C18ee-01 Stroke Sensor
  • C18ee-04 Stroke Sensor
  • C18ee-64 Stroke Sensor
  • C18ee-87 Stroke Sensor
  • C18ee-96 Stroke Sensor
  • C18ef-16 Rotor Position Sensor
  • C18ef-17 Rotor Position Sensor
  • C18ef-96 Rotor Position Sensor
  • C18f1-08 Vdc System
  • C18f3-04 Overheat
  • C18f3-4b Overheat
  • C18f4-86 Bcm System
  • C18f5-08 Ipdm E/r System
  • C18f6-08 Vcm System
  • C18f7-08 Abs Actuator and Electric Unit (control Unit) System
  • C18f7-86 Abs Actuator and Electric Unit (control Unit) System
  • C18f8-08 Vcm System
  • C18f8-86 Vcm System
  • C18f9-02 Abs Actuator and Electric Unit (control Unit) System
  • C18fa-44 Programing Incomplete
  • C18fa-46 Programing Incomplete
  • C18fc-18 Temperature Sensor
  • C18fc-19 Temperature Sensor
  • C18fd-18 Temperature Sensor
  • C18fd-19 Temperature Sensor
  • C18fe-29 Temperature Sensor
  • U1fa1-86 Can Comm Circuit
  • U2140-87 Can Comm Circuit
  • U2143-87 Can Comm Circuit
  • U2148-87 Can Comm Circuit
  • U214f-87 Can Comm Circuit
  • U2240-87 Can Comm Circuit
  • U2243-87 Can Comm Circuit
  • U2248-87 Can Comm Circuit
  • U224f-87 Can Comm Circuit
  • U2252-87 Can Comm Circuit
  • U225b-87 Can Comm Circuit
  • Power Supply and Ground Circuit
  • Warning Buzzer
  • Brake Warning Lamp
  • Brake System Warning Lamp

B14e0-02 Wheel Sensor Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E0 02 Wheel sensor Diagnosis condition Power switch is ON.
Signal (terminal) Front left wheel sensor signal
Threshold When a malfunction is detected in front left wheel sensor.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Front left wheel sensor

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–02" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E0–02" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL SENSOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the front left wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the front left wheel sensor. Refer to Removal and Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–02” detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the front left wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 6.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–02” detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–02” detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect front left wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and front left wheel sensor harness connector.

    • Measurement connector and terminal for power supply circuit

      Electrically-driven intelligent brake unitFront left wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 4 B176 1 Existed
    • Measurement connector and terminal for signal circuit

      Electrically-driven intelligent brake unitFront left wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 21 B176 2 Existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 10.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect front left wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–02” detected?

YES>>

GO TO 11.

NO>>

INSPECTION END

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect front left wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to front left wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 12.

REPLACE WHEEL SENSOR

  1. Replace the front left wheel sensor. Refer to Removal and Installation.

  2. Connect electrically-driven intelligent brake unit harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–02” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e0-09 Wheel Sensor Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E0 09 Wheel sensor Diagnosis condition Power switch is ON.
Signal (terminal) Front left wheel sensor signal
Threshold When distance between front left wheel sensor and front left wheel sensor rotor is large.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Front left wheel sensor

  • Front left sensor rotor

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–09" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E0–09" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL HUB ASSEMBLY

Check that there is no excessive looseness in front left wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace the front left wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation. GO TO 4.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 5.

CHECK TIRE

  1. Power switch OFF.

  2. Check the front left tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Adjust air pressure or replace front left tire. GO TO 6.

CHECK DATA MONITOR (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 7.

NO>>

GO TO 8.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–09” detected?

YES>>

GO TO 8.

NO>>

INSPECTION END

CHECK WHEEL SENSOR AND SENSOR ROTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect front left wheel sensor harness connector.

  5. Remove dust and foreign matter adhered to the front left wheel sensor and front left sensor rotor with a vacuum dust collector through the front left wheel sensor mounting hole.

>>

GO TO 9.

CHECK WHEEL SENSOR

Check the front left wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 13.

NO>>

GO TO 10.

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect front left wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to front left wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 11.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the front left wheel sensor. Refer to Removal and Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Set the vehicle to READY.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  10. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 12.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–09” detected?

YES>>

GO TO 24.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the front left wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 16.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 14.

CHECK DATA MONITOR (2)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 15.

NO>>

GO TO 16.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–09” detected?

YES>>

GO TO 16.

NO>>

INSPECTION END

CHECK TERMINAL

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit terminals for damage or loose connection with harness connector.

  6. Disconnect front left wheel sensor harness connector.

  7. Check the front left wheel sensor terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 19.

NO>>

Repair / replace harness, connector, or terminal. GO TO 17.

CHECK DATA MONITOR (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect front left wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 18.

NO>>

GO TO 19.

PERFORM SELF-DIAGNOSIS (5)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–09” detected?

YES>>

GO TO 19.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect front left wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and front left wheel sensor harness connector.

    Electrically-driven intelligent brake unit—Continuity
    ConnectorTerminal
    B64 4, 21 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 20.

NO>>

Repair / replace harness or connector. GO TO 20.

CHECK DATA MONITOR (4)

With CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect front left wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 21.

NO>>

GO TO 22.

PERFORM SELF-DIAGNOSIS (6)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–09” detected?

YES>>

GO TO 22.

NO>>

INSPECTION END

REPLACE WHEEL SENSOR (2)

With CONSULT

  1. Replace the front left wheel sensor. Refer to Removal and Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Set the vehicle to READY.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  9. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 23.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (7)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–09” detected?

YES>>

GO TO 24.

NO>>

INSPECTION END

REPLACE SENSOR ROTOR

With CONSULT

  1. Replace the front left sensor rotor. Refer to FRONT SENSOR ROTOR : Removal & Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Set the Nissan Ariya vehicle to READY.

  8. Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.

  9. Stop the Nissan Ariya vehicle.

  10. Power switch OFF and disconnect CONSULT from data link connector.

  11. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  12. Power switch ON without depressing the brake pedal.

  13. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–09” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e0-38 Wheel Sensor Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E0 38 Wheel sensor 1 Diagnosis condition Power switch is ON.
Signal (terminal) Front left wheel sensor signal
Threshold When a malfunction is detected in information of front left wheel sensor.
Diagnosis delay time 1 second or less
2 Diagnosis condition Power switch is ON.
Signal (terminal) Front left wheel sensor signal
Threshold When a malfunction is detected in rotation speed of front left wheel sensor.
Diagnosis delay time 1 second or less
3 Diagnosis condition Power switch is ON.
Signal (terminal) Front left wheel sensor signal
Threshold When a noise is detected in front left wheel sensor.
Diagnosis delay time 1 second or less
4 Diagnosis condition Power switch is ON.
Signal (terminal) Front left wheel sensor signal
Threshold When a no signal detected in front left wheel sensor.
Diagnosis delay time 1 second or less
5 Diagnosis condition Power switch is ON.
Signal (terminal) Front left wheel sensor signal
Threshold When a malfunction is detected in signal of front left wheel sensor.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Front left wheel sensor

  • Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–38" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E0–38" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL HUB ASSEMBLY

Check that there is no excessive looseness in front left wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace the front left wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation. GO TO 4.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 5.

CHECK TIRE

  1. Power switch OFF.

  2. Check the front left tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Adjust air pressure or replace front left tire. GO TO 6.

CHECK DATA MONITOR (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 7.

NO>>

GO TO 8.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–38” detected?

YES>>

GO TO 8.

NO>>

INSPECTION END

CHECK WHEEL SENSOR AND SENSOR ROTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect front left wheel sensor harness connector.

  5. Remove dust and foreign matter adhered to the front left wheel sensor and front left sensor rotor with a vacuum dust collector through the front left wheel sensor mounting hole.

>>

GO TO 9.

CHECK WHEEL SENSOR

Check the front left wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 13.

NO>>

GO TO 10.

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect front left wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to front left wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 11.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the front left wheel sensor. Refer to Removal and Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Set the vehicle to READY.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  10. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 12.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–38” detected?

YES>>

GO TO 24.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the front left wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 16.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 14.

CHECK DATA MONITOR (2)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 15.

NO>>

GO TO 16.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–38” detected?

YES>>

GO TO 16.

NO>>

INSPECTION END

CHECK TERMINAL

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit terminals for damage or loose connection with harness connector.

  6. Disconnect front left wheel sensor harness connector.

  7. Check the front left wheel sensor terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 19.

NO>>

Repair / replace harness, connector, or terminal. GO TO 17.

CHECK DATA MONITOR (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect front left wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 18.

NO>>

GO TO 19.

PERFORM SELF-DIAGNOSIS (5)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–38” detected?

YES>>

GO TO 19.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect front left wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and front left wheel sensor harness connector.

    Electrically-driven intelligent brake unit—Continuity
    ConnectorTerminal
    B64 4, 21 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 20.

NO>>

Repair / replace harness or connector. GO TO 20.

CHECK DATA MONITOR (4)

With CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect front left wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 21.

NO>>

GO TO 22.

PERFORM SELF-DIAGNOSIS (6)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–38” detected?

YES>>

GO TO 22.

NO>>

INSPECTION END

REPLACE WHEEL SENSOR (2)

With CONSULT

  1. Replace the front left wheel sensor. Refer to Removal and Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Set the vehicle to READY.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  9. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 23.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (7)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–38” detected?

YES>>

GO TO 24.

NO>>

INSPECTION END

REPLACE SENSOR ROTOR

With CONSULT

  1. Replace the front left sensor rotor. Refer to FRONT SENSOR ROTOR : Removal & Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Set the Nissan Ariya vehicle to READY.

  8. Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.

  9. Stop the Nissan Ariya vehicle.

  10. Power switch OFF and disconnect CONSULT from data link connector.

  11. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  12. Power switch ON without depressing the brake pedal.

  13. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–38” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e0-4a Wheel Sensor Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E0 4A Wheel sensor Diagnosis condition Power switch is ON.
Signal (terminal) Front left wheel sensor signal
Threshold When front left wheel sensor is installed to wrong position.
Diagnosis delay time 3 seconds or less

POSSIBLE CAUSE

  • Front left wheel sensor

  • Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E0–4A" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E0–4A" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

REPLACE WHEEL SENSOR

  1. Replace the front left wheel sensor. Refer to Removal and Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is the display result "B14E0-4A" of “CRNT”?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e1-09 Wheel Sensor Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E1 09 Wheel sensor Diagnosis condition Power switch is ON.
Signal (terminal) Front right wheel sensor signal
Threshold When distance between front right wheel sensor and front right wheel sensor rotor is large.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Front right wheel sensor

  • Front right sensor rotor

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–09" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E1–09" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL HUB ASSEMBLY

Check that there is no excessive looseness in front right wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace the front right wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation. GO TO 4.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 5.

CHECK TIRE

  1. Power switch OFF.

  2. Check the front right tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Adjust air pressure or replace front right tire. GO TO 6.

CHECK DATA MONITOR (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 7.

NO>>

GO TO 8.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–09” detected?

YES>>

GO TO 8.

NO>>

INSPECTION END

CHECK WHEEL SENSOR AND SENSOR ROTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect front right wheel sensor harness connector.

  5. Remove dust and foreign matter adhered to the front right wheel sensor and front right sensor rotor with a vacuum dust collector through the front right wheel sensor mounting hole.

>>

GO TO 9.

CHECK WHEEL SENSOR

Check the front right wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 13.

NO>>

GO TO 10.

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect front right wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to front right wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 11.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the front right wheel sensor. Refer to Removal and Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Set the vehicle to READY.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  10. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 12.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–09” detected?

YES>>

GO TO 24.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the front right wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 16.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 14.

CHECK DATA MONITOR (2)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 15.

NO>>

GO TO 16.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–09” detected?

YES>>

GO TO 16.

NO>>

INSPECTION END

CHECK TERMINAL

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit terminals for damage or loose connection with harness connector.

  6. Disconnect front right wheel sensor harness connector.

  7. Check the front right wheel sensor terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 19.

NO>>

Repair / replace harness, connector, or terminal. GO TO 17.

CHECK DATA MONITOR (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect front right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 18.

NO>>

GO TO 19.

PERFORM SELF-DIAGNOSIS (5)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–09” detected?

YES>>

GO TO 19.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect front right wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and front right wheel sensor harness connector.

    Electrically-driven intelligent brake unit—Continuity
    ConnectorTerminal
    B64 12, 11 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 20.

NO>>

Repair / replace harness or connector. GO TO 20.

CHECK DATA MONITOR (4)

With CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect front right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 21.

NO>>

GO TO 22.

PERFORM SELF-DIAGNOSIS (6)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–09” detected?

YES>>

GO TO 22.

NO>>

INSPECTION END

REPLACE WHEEL SENSOR (2)

With CONSULT

  1. Replace the front right wheel sensor. Refer to Removal and Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Set the vehicle to READY.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  9. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 23.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (7)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–09” detected?

YES>>

GO TO 24.

NO>>

INSPECTION END

REPLACE SENSOR ROTOR

With CONSULT

  1. Replace the front right sensor rotor. Refer to FRONT SENSOR ROTOR : Removal & Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Set the Nissan Ariya vehicle to READY.

  8. Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.

  9. Stop the Nissan Ariya vehicle.

  10. Power switch OFF and disconnect CONSULT from data link connector.

  11. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  12. Power switch ON without depressing the brake pedal.

  13. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–09” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e1-38 Wheel Sensor Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E1 38 Wheel sensor 1 Diagnosis condition Power switch is ON.
Signal (terminal) Front right wheel sensor signal
Threshold When a malfunction is detected in information of front right wheel sensor.
Diagnosis delay time 1 second or less
2 Diagnosis condition Power switch is ON.
Signal (terminal) Front right wheel sensor signal
Threshold When a malfunction is detected in rotation speed of front right wheel sensor.
Diagnosis delay time 1 second or less
3 Diagnosis condition Power switch is ON.
Signal (terminal) Front right wheel sensor signal
Threshold When a noise is detected in front right wheel sensor.
Diagnosis delay time 1 second or less
4 Diagnosis condition Power switch is ON.
Signal (terminal) Front right wheel sensor signal
Threshold When a no signal detected in front right wheel sensor.
Diagnosis delay time 1 second or less
5 Diagnosis condition Power switch is ON.
Signal (terminal) Front right wheel sensor signal
Threshold When a malfunction is detected in signal of front right wheel sensor.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Front right wheel sensor

  • Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–38" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E1–38" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL HUB ASSEMBLY

Check that there is no excessive looseness in front right wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace the front right wheel hub assembly. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal & Installation. GO TO 4.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 5.

CHECK TIRE

  1. Power switch OFF.

  2. Check the front right tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Adjust air pressure or replace front right tire. GO TO 6.

CHECK DATA MONITOR (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 7.

NO>>

GO TO 8.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–38” detected?

YES>>

GO TO 8.

NO>>

INSPECTION END

CHECK WHEEL SENSOR AND SENSOR ROTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect front right wheel sensor harness connector.

  5. Remove dust and foreign matter adhered to the front right wheel sensor and front right sensor rotor with a vacuum dust collector through the front right wheel sensor mounting hole.

>>

GO TO 9.

CHECK WHEEL SENSOR

Check the front right wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 13.

NO>>

GO TO 10.

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect front right wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to front right wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 11.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the front right wheel sensor. Refer to Removal and Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Set the vehicle to READY.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  10. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 12.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–38” detected?

YES>>

GO TO 24.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the front right wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 16.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 14.

CHECK DATA MONITOR (2)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 15.

NO>>

GO TO 16.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–38” detected?

YES>>

GO TO 16.

NO>>

INSPECTION END

CHECK TERMINAL

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit terminals for damage or loose connection with harness connector.

  6. Disconnect front right wheel sensor harness connector.

  7. Check the front right wheel sensor terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 19.

NO>>

Repair / replace harness, connector, or terminal. GO TO 17.

CHECK DATA MONITOR (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect front right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 18.

NO>>

GO TO 19.

PERFORM SELF-DIAGNOSIS (5)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–38” detected?

YES>>

GO TO 19.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect front right wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and front right wheel sensor harness connector.

    Electrically-driven intelligent brake unit—Continuity
    ConnectorTerminal
    B64 12, 11 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 20.

NO>>

Repair / replace harness or connector. GO TO 20.

CHECK DATA MONITOR (4)

With CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect front right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 21.

NO>>

GO TO 22.

PERFORM SELF-DIAGNOSIS (6)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–38” detected?

YES>>

GO TO 22.

NO>>

INSPECTION END

REPLACE WHEEL SENSOR (2)

With CONSULT

  1. Replace the front right wheel sensor. Refer to Removal and Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Set the vehicle to READY.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  9. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 23.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (7)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–38” detected?

YES>>

GO TO 24.

NO>>

INSPECTION END

REPLACE SENSOR ROTOR

With CONSULT

  1. Replace the front right sensor rotor. Refer to FRONT SENSOR ROTOR : Removal & Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Set the Nissan Ariya vehicle to READY.

  8. Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.

  9. Stop the Nissan Ariya vehicle.

  10. Power switch OFF and disconnect CONSULT from data link connector.

  11. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  12. Power switch ON without depressing the brake pedal.

  13. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–38” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e1-4a Wheel Sensor Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E1 4A Wheel sensor Diagnosis condition Power switch is ON.
Signal (terminal) Front right wheel sensor signal
Threshold When front right wheel sensor is installed to wrong position.
Diagnosis delay time 3 seconds or less

POSSIBLE CAUSE

  • Front right wheel sensor

  • Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E1–4A" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E1–4A" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

REPLACE WHEEL SENSOR

  1. Replace the front right wheel sensor. Refer to Removal and Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is the display result "B14E1-4A" of “CRNT”?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e2-09 Wheel Sensor Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E2 09 Wheel sensor Diagnosis condition Power switch is ON.
Signal (terminal) Rear left wheel sensor signal
Threshold When distance between rear left wheel sensor and rear left wheel sensor rotor is large.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Rear left wheel sensor

  • Rear left sensor rotor

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–09" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E2–09" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL HUB ASSEMBLY

Check that there is no excessive looseness in rear left wheel hub assembly. Refer to REAR WHEEL HUB : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace the rear left wheel hub assembly. Refer to REAR WHEEL HUB : Removal & Installation. GO TO 4.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 5.

CHECK TIRE

  1. Power switch OFF.

  2. Check the rear left tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Adjust air pressure or replace rear left tire. GO TO 6.

CHECK DATA MONITOR (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 7.

NO>>

GO TO 8.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–09” detected?

YES>>

GO TO 8.

NO>>

INSPECTION END

CHECK WHEEL SENSOR AND SENSOR ROTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect rear left wheel sensor harness connector.

  5. Remove dust and foreign matter adhered to the rear left wheel sensor and rear left sensor rotor with a vacuum dust collector through the rear left wheel sensor mounting hole.

>>

GO TO 9.

CHECK WHEEL SENSOR

Check the rear left wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 13.

NO>>

GO TO 10.

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect rear left wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to rear left wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 11.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Set the vehicle to READY.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  10. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 12.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–09” detected?

YES>>

GO TO 24.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the rear left wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 16.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 14.

CHECK DATA MONITOR (2)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 15.

NO>>

GO TO 16.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–09” detected?

YES>>

GO TO 16.

NO>>

INSPECTION END

CHECK TERMINAL

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit terminals for damage or loose connection with harness connector.

  6. Disconnect rear left wheel sensor harness connector.

  7. Check the rear left wheel sensor terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 19.

NO>>

Repair / replace harness, connector, or terminal. GO TO 17.

CHECK DATA MONITOR (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect rear left wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 18.

NO>>

GO TO 19.

PERFORM SELF-DIAGNOSIS (5)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–09” detected?

YES>>

GO TO 19.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect rear left wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and rear left wheel sensor harness connector.

    Electrically-driven intelligent brake unit—Continuity
    ConnectorTerminal
    B64 3, 19 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 20.

NO>>

Repair / replace harness or connector. GO TO 20.

CHECK DATA MONITOR (4)

With CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect rear left wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 21.

NO>>

GO TO 22.

PERFORM SELF-DIAGNOSIS (6)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–09” detected?

YES>>

GO TO 22.

NO>>

INSPECTION END

REPLACE WHEEL SENSOR (2)

With CONSULT

  1. Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Set the vehicle to READY.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  9. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 23.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (7)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–09” detected?

YES>>

GO TO 24.

NO>>

INSPECTION END

REPLACE SENSOR ROTOR

With CONSULT

  1. Replace the rear left sensor rotor. Refer to REAR SENSOR ROTOR : Removal & Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Set the Nissan Ariya vehicle to READY.

  8. Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.

  9. Stop the Nissan Ariya vehicle.

  10. Power switch OFF and disconnect CONSULT from data link connector.

  11. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  12. Power switch ON without depressing the brake pedal.

  13. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–09” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e2-38 Wheel Sensor Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E2 38 Wheel sensor 1 Diagnosis condition Power switch is ON.
Signal (terminal) Rear left wheel sensor signal
Threshold When a malfunction is detected in information of rear left wheel sensor.
Diagnosis delay time 1 second or less
2 Diagnosis condition Power switch is ON.
Signal (terminal) Rear left wheel sensor signal
Threshold When a malfunction is detected in rotation speed of rear left wheel sensor.
Diagnosis delay time 1 second or less
3 Diagnosis condition Power switch is ON.
Signal (terminal) Rear left wheel sensor signal
Threshold When a noise is detected in rear left wheel sensor.
Diagnosis delay time 1 second or less
4 Diagnosis condition Power switch is ON.
Signal (terminal) Rear left wheel sensor signal
Threshold When a no signal detected in rear left wheel sensor.
Diagnosis delay time 1 second or less
5 Diagnosis condition Power switch is ON.
Signal (terminal) Rear left wheel sensor signal
Threshold When a malfunction is detected in signal of rear left wheel sensor.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Rear left wheel sensor

  • Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–38" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E2–38" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL HUB ASSEMBLY

Check that there is no excessive looseness in rear left wheel hub assembly. Refer to REAR WHEEL HUB : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace the rear left wheel hub assembly. Refer to REAR WHEEL HUB : Removal & Installation. GO TO 4.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 5.

CHECK TIRE

  1. Power switch OFF.

  2. Check the rear left tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Adjust air pressure or replace rear left tire. GO TO 6.

CHECK DATA MONITOR (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 7.

NO>>

GO TO 8.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–38” detected?

YES>>

GO TO 8.

NO>>

INSPECTION END

CHECK WHEEL SENSOR AND SENSOR ROTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect rear left wheel sensor harness connector.

  5. Remove dust and foreign matter adhered to the rear left wheel sensor and rear left sensor rotor with a vacuum dust collector through the rear left wheel sensor mounting hole.

>>

GO TO 9.

CHECK WHEEL SENSOR

Check the rear left wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 13.

NO>>

GO TO 10.

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect rear left wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to rear left wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 11.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Set the vehicle to READY.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  10. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 12.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–38” detected?

YES>>

GO TO 24.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the rear left wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 16.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 14.

CHECK DATA MONITOR (2)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 15.

NO>>

GO TO 16.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–38” detected?

YES>>

GO TO 16.

NO>>

INSPECTION END

CHECK TERMINAL

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit terminals for damage or loose connection with harness connector.

  6. Disconnect rear left wheel sensor harness connector.

  7. Check the rear left wheel sensor terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 19.

NO>>

Repair / replace harness, connector, or terminal. GO TO 17.

CHECK DATA MONITOR (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect rear left wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 18.

NO>>

GO TO 19.

PERFORM SELF-DIAGNOSIS (5)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–38” detected?

YES>>

GO TO 19.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect rear left wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and rear left wheel sensor harness connector.

    Electrically-driven intelligent brake unit—Continuity
    ConnectorTerminal
    B64 3, 19 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 20.

NO>>

Repair / replace harness or connector. GO TO 20.

CHECK DATA MONITOR (4)

With CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect rear left wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 21.

NO>>

GO TO 22.

PERFORM SELF-DIAGNOSIS (6)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–38” detected?

YES>>

GO TO 22.

NO>>

INSPECTION END

REPLACE WHEEL SENSOR (2)

With CONSULT

  1. Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Set the vehicle to READY.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  9. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 23.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (7)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–38” detected?

YES>>

GO TO 23.

NO>>

INSPECTION END

REPLACE SENSOR ROTOR

With CONSULT

  1. Replace the rear left sensor rotor. Refer to REAR SENSOR ROTOR : Removal & Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Set the Nissan Ariya vehicle to READY.

  8. Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.

  9. Stop the Nissan Ariya vehicle.

  10. Power switch OFF and disconnect CONSULT from data link connector.

  11. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  12. Power switch ON without depressing the brake pedal.

  13. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–38” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e2-4a Wheel Sensor Nissan Ariya 1st generation

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E2 4A Wheel sensor Diagnosis condition Power switch is ON.
Signal (terminal) Rear left wheel sensor signal
Threshold When rear left wheel sensor is installed to wrong position.
Diagnosis delay time 3 seconds or less

POSSIBLE CAUSE

  • Rear left wheel sensor

  • Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–4A" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E2–4A" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

REPLACE WHEEL SENSOR

  1. Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is the display result "B14E2-4A" of “CRNT”?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e2-64 Wheel Sensor Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E2 64 Wheel sensor 1 Diagnosis condition Power switch is ON.
Signal (terminal) Rear left wheel sensor signal
Threshold When difference between the rear left wheel sensor and the wheel speed other than the rear left wheel sensor is 6 km/h or more [when driving 100 km/h or less].
Diagnosis delay time 18 seconds or more
2 Diagnosis condition Power switch is ON.
Signal (terminal) Rear left wheel sensor signal
Threshold When difference between the rear left wheel sensor and the wheel speed other than the rear left wheel sensor is 6% or more [when driving 100 km/h or less].
Diagnosis delay time 1 second or less
3 Diagnosis condition Power switch is ON.
Signal (terminal) Rear left wheel sensor signal
Threshold When a malfunction is detected in rotation speed of rear left wheel sensor.
Diagnosis delay time 1 second or less
4 Diagnosis condition Power switch is ON.
Signal (terminal) Rear left wheel sensor signal
Threshold When rear left wheel sensor is different rotation direction from wheel sensor other than rear wheel left.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Rear left wheel sensor

  • Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–64" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E2–64" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL SENSOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the rear left wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–64” detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the rear left wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 6.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–64” detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–64” detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect rear left wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and rear left wheel sensor harness connector.

    • Measurement connector and terminal for power supply circuit

      Electrically-driven intelligent brake unitRear left wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 3 B179 1 Existed
    • Measurement connector and terminal for signal circuit

      Electrically-driven intelligent brake unitRear left wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 19 B179 2 Existed

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace harness or connector. GO TO 10.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect rear left wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–64” detected?

YES>>

GO TO 11.

NO>>

INSPECTION END

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect rear left wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to rear left wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 12.

REPLACE WHEEL SENSOR

  1. Replace the rear left wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect electrically-driven intelligent brake unit harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E2–64” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e3-02 Wheel Sensor Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E3 02 Wheel sensor Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When a malfunction is detected in rear right wheel sensor.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Rear right wheel sensor

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–02" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E3–02" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL SENSOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the rear right wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–02” detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the rear right wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 6.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–02” detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–02” detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect rear right wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and rear right wheel sensor harness connector.

    • Measurement connector and terminal for power supply circuit

      Electrically-driven intelligent brake unitRear right wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 7 B181 1 Existed
    • Measurement connector and terminal for signal circuit

      Electrically-driven intelligent brake unitRear right wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 15 B181 2 Existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 10.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect rear right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–02” detected?

YES>>

GO TO 11.

NO>>

INSPECTION END

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect rear right wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 12.

REPLACE WHEEL SENSOR

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect electrically-driven intelligent brake unit harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–02” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e3-09 Wheel Sensor Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E3 09 Wheel sensor Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When distance between rear right wheel sensor and rear right wheel sensor rotor is large.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Rear right wheel sensor

  • Rear right sensor rotor

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–09" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E3–09" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL HUB ASSEMBLY

Check that there is no excessive looseness in rear right wheel hub assembly. Refer to REAR WHEEL HUB : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace the rear right wheel hub assembly. Refer to REAR WHEEL HUB : Removal & Installation. GO TO 4.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 5.

CHECK TIRE

  1. Power switch OFF.

  2. Check the rear right tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Adjust air pressure or replace rear right tire. GO TO 6.

CHECK DATA MONITOR (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 7.

NO>>

GO TO 8.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–09” detected?

YES>>

GO TO 8.

NO>>

INSPECTION END

CHECK WHEEL SENSOR AND SENSOR ROTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect rear right wheel sensor harness connector.

  5. Remove dust and foreign matter adhered to the rear right wheel sensor and rear right sensor rotor with a vacuum dust collector through the rear right wheel sensor mounting hole.

>>

GO TO 9.

CHECK WHEEL SENSOR

Check the rear right wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 13.

NO>>

GO TO 10.

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect rear right wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 11.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Set the vehicle to READY.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  10. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 12.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–09” detected?

YES>>

GO TO 24.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the rear right wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 16.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 14.

CHECK DATA MONITOR (2)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 15.

NO>>

GO TO 16.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–09” detected?

YES>>

GO TO 16.

NO>>

INSPECTION END

CHECK TERMINAL

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit terminals for damage or loose connection with harness connector.

  6. Disconnect rear right wheel sensor harness connector.

  7. Check the rear right wheel sensor terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 19.

NO>>

Repair / replace harness, connector, or terminal. GO TO 17.

CHECK DATA MONITOR (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect rear right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 18.

NO>>

GO TO 19.

PERFORM SELF-DIAGNOSIS (5)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–09” detected?

YES>>

GO TO 19.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect rear right wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and rear right wheel sensor harness connector.

    Electrically-driven intelligent brake unit—Continuity
    ConnectorTerminal
    B64 7, 15 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 20.

NO>>

Repair / replace harness or connector. GO TO 20.

CHECK DATA MONITOR (4)

With CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect rear right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 21.

NO>>

GO TO 22.

PERFORM SELF-DIAGNOSIS (6)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–09” detected?

YES>>

GO TO 22.

NO>>

INSPECTION END

REPLACE WHEEL SENSOR (2)

With CONSULT

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Set the vehicle to READY.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  9. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 23.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (7)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–09” detected?

YES>>

GO TO 24.

NO>>

INSPECTION END

REPLACE SENSOR ROTOR

With CONSULT

  1. Replace the rear right sensor rotor. Refer to REAR SENSOR ROTOR : Removal & Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Set the Nissan Ariya vehicle to READY.

  8. Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.

  9. Stop the Nissan Ariya vehicle.

  10. Power switch OFF and disconnect CONSULT from data link connector.

  11. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  12. Power switch ON without depressing the brake pedal.

  13. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–09” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e3-11 Wheel Sensor Nissan Ariya 1st generation

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E3 11 Wheel sensor 1 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When an open circuit is detected in rear right wheel sensor circuit (signal line).
Diagnosis delay time 1 second or less
2 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When short circuit to ground side is detected in rear right wheel sensor circuit (signal line).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector

  • Rear right wheel sensor

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3-11" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E3–11" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL SENSOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the rear right wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–11” detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the rear right wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 6.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–11” detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–11” detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect rear right wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and rear right wheel sensor harness connector.

    • Measurement connector and terminal for power supply circuit

      Electrically-driven intelligent brake unitRear right wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 7 B181 1 Existed
    • Measurement connector and terminal for signal circuit

      Electrically-driven intelligent brake unitRear right wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 15 B181 2 Existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 10.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect rear right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–11” detected?

YES>>

GO TO 11.

NO>>

INSPECTION END

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect rear right wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 12.

REPLACE WHEEL SENSOR

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect electrically-driven intelligent brake unit harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–11” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e3-12 Wheel Sensor Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E3 12 Wheel sensor Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When short circuit to power supply side is detected in rear right wheel sensor circuit (signal line).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector

  • Rear right wheel sensor

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–12" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E3–12" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL SENSOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the rear right wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–12” detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the rear right wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 6.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–12” detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–12” detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect rear right wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and rear right wheel sensor harness connector.

    • Measurement connector and terminal for power supply circuit

      Electrically-driven intelligent brake unitRear right wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 7 B181 1 Existed
    • Measurement connector and terminal for signal circuit

      Electrically-driven intelligent brake unitRear right wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 15 B181 2 Existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 10.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect rear right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–12” detected?

YES>>

GO TO 11.

NO>>

INSPECTION END

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect rear right wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 12.

REPLACE WHEEL SENSOR

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect electrically-driven intelligent brake unit harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–12” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e3-13 Wheel Sensor Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E3 13 Wheel sensor 1 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When an open circuit is detected in rear right wheel sensor circuit (power supply line).
Diagnosis delay time 1 second or less
2 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When short circuit to ground side is detected in rear right wheel sensor circuit (power supply line).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector

  • Rear right wheel sensor

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–13" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E3–13" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL SENSOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the rear right wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–13” detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the rear right wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 6.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–13” detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–13” detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect rear right wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and rear right wheel sensor harness connector.

    • Measurement connector and terminal for power supply circuit

      Electrically-driven intelligent brake unitRear right wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 7 B181 1 Existed
    • Measurement connector and terminal for signal circuit

      Electrically-driven intelligent brake unitRear right wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 15 B181 2 Existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 10.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect rear right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–13” detected?

YES>>

GO TO 11.

NO>>

INSPECTION END

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect rear right wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 12.

REPLACE WHEEL SENSOR

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect electrically-driven intelligent brake unit harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–13” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e3-1c Wheel Sensor Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E3 1C Wheel sensor 1 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When rear right wheel sensor power supply voltage is 6.7 V or less.
Diagnosis delay time 1 second or less
2 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When an open circuit is detected in rear right wheel sensor circuit (power supply line).
Diagnosis delay time 1 second or less
3 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When short circuit to ground side is detected in rear right wheel sensor circuit (power supply line).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector

  • Rear right wheel sensor

  • Electrically-driven intelligent brake unit

  • Electrically-driven intelligent brake unit power supply

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–1C" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E3–1C" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL SENSOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the rear right wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–1C” detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the rear right wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 6.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–1C” detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–1C” detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect rear right wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and rear right wheel sensor harness connector.

    • Measurement connector and terminal for power supply circuit

      Electrically-driven intelligent brake unitRear right wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 7 B181 1 Existed
    • Measurement connector and terminal for signal circuit

      Electrically-driven intelligent brake unitRear right wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 15 B181 2 Existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 10.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect rear right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–1C” detected?

YES>>

GO TO 11.

NO>>

INSPECTION END

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect rear right wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 12.

REPLACE WHEEL SENSOR

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect electrically-driven intelligent brake unit harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–1C” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e3-38 Wheel Sensor Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C14E3 38 Wheel sensor 1 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When a malfunction is detected in information of rear right wheel sensor.
Diagnosis delay time 1 second or less
2 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When a malfunction is detected in rotation speed of rear right wheel sensor.
Diagnosis delay time 1 second or less
3 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When a noise is detected in rear right wheel sensor.
Diagnosis delay time 1 second or less
4 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When a no signal detected in rear right wheel sensor.
Diagnosis delay time 1 second or less
5 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When a malfunction is detected in signal of rear right wheel sensor.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Rear right wheel sensor

  • Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–38" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E3–38" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL HUB ASSEMBLY

Check that there is no excessive looseness in rear right wheel hub assembly. Refer to REAR WHEEL HUB : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace the rear right wheel hub assembly. Refer to REAR WHEEL HUB : Removal & Installation. GO TO 4.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 5.

CHECK TIRE

  1. Power switch OFF.

  2. Check the rear right tire air pressure, wear and size. Refer to TIRE AIR PRESSURE : Service Data.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Adjust air pressure or replace rear right tire. GO TO 6.

CHECK DATA MONITOR (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 7.

NO>>

GO TO 8.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–38” detected?

YES>>

GO TO 8.

NO>>

INSPECTION END

CHECK WHEEL SENSOR AND SENSOR ROTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect rear right wheel sensor harness connector.

  5. Remove dust and foreign matter adhered to the rear right wheel sensor and rear right sensor rotor with a vacuum dust collector through the rear right wheel sensor mounting hole.

>>

GO TO 9.

CHECK WHEEL SENSOR

Check the rear right wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 13.

NO>>

GO TO 10.

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect rear right wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 11.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Set the vehicle to READY.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  10. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 12.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–38” detected?

YES>>

GO TO 24.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the rear right wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 16.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 14.

CHECK DATA MONITOR (2)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Set the vehicle to READY.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 15.

NO>>

GO TO 16.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–38” detected?

YES>>

GO TO 16.

NO>>

INSPECTION END

CHECK TERMINAL

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit terminals for damage or loose connection with harness connector.

  6. Disconnect rear right wheel sensor harness connector.

  7. Check the rear right wheel sensor terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 19.

NO>>

Repair / replace harness, connector, or terminal. GO TO 17.

CHECK DATA MONITOR (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect rear right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 18.

NO>>

GO TO 19.

PERFORM SELF-DIAGNOSIS (5)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–38” detected?

YES>>

GO TO 19.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect rear right wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and rear right wheel sensor harness connector.

    Electrically-driven intelligent brake unit—Continuity
    ConnectorTerminal
    B64 7, 15 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 20.

NO>>

Repair / replace harness or connector. GO TO 20.

CHECK DATA MONITOR (4)

With CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect rear right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Set the vehicle to READY.

  9. Erase self-diagnosis result for “BRAKE”.

  10. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  11. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 21.

NO>>

GO TO 22.

PERFORM SELF-DIAGNOSIS (6)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–38” detected?

YES>>

GO TO 22.

NO>>

INSPECTION END

REPLACE WHEEL SENSOR (2)

With CONSULT

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Set the vehicle to READY.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Select “BRAKE” and “Data monitor”, check “Front LH wheel speed”, “Front RH wheel speed“, “Rear LH wheel speed“, and “Rear RH wheel speed“.

  9. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 23.

NO>>

GO TO 24.

PERFORM SELF-DIAGNOSIS (7)

With CONSULT

  1. Stop the Nissan Ariya vehicle.

  2. Power switch OFF.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–38” detected?

YES>>

GO TO 24.

NO>>

INSPECTION END

REPLACE SENSOR ROTOR

With CONSULT

  1. Replace the rear right sensor rotor. Refer to REAR SENSOR ROTOR : Removal & Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Set the Nissan Ariya vehicle to READY.

  8. Drive the vehicle at approximately 50 km/h or more for approximately 2 minutes.

  9. Stop the Nissan Ariya vehicle.

  10. Power switch OFF and disconnect CONSULT from data link connector.

  11. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  12. Power switch ON without depressing the brake pedal.

  13. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–38” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e3-4a Wheel Sensor Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E3 4A Wheel sensor Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When rear right wheel sensor is installed to wrong position.
Diagnosis delay time 3 seconds or less.

POSSIBLE CAUSE

  • Rear right wheel sensor

  • Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–4A" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E3–4A" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

REPLACE WHEEL SENSOR

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is the display result "B14E3-4A" of “CRNT”?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e3-64 Wheel Sensor Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E3 64 Wheel sensor 1 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When difference between the rear right wheel sensor and the wheel speed other than the rear right wheel sensor is 6 km/h or more [when driving 100 km/h or less].
Diagnosis delay time 18 seconds or more
2 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When difference between the rear right wheel sensor and the wheel speed other than the rear right wheel sensor is 6% or more [when driving 100 km/h or less].
Diagnosis delay time 1 second or less
3 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When a malfunction is detected in rotation speed of rear right wheel sensor.
Diagnosis delay time 1 second or less
4 Diagnosis condition Power switch is ON.
Signal (terminal) Rear right wheel sensor signal
Threshold When rear right wheel sensor is different rotation direction from wheel sensor other than front wheel left.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Rear right wheel sensor

  • Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–64" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E3–64" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL SENSOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the rear right wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–64” detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the rear right wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 6.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–64” detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–64” detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect rear right wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and rear right wheel sensor harness connector.

    • Measurement connector and terminal for power supply circuit

      Electrically-driven intelligent brake unitRear right wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 7 B181 1 Existed
    • Measurement connector and terminal for signal circuit

      Electrically-driven intelligent brake unitRear right wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 15 B181 2 Existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 10.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect rear right wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–64” detected?

YES>>

GO TO 11.

NO>>

INSPECTION END

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect rear right wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to rear right wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 12.

REPLACE WHEEL SENSOR

  1. Replace the rear right wheel sensor. Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect electrically-driven intelligent brake unit harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E3–64” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e4-64 Wheel Sensor Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E4 64 Wheel sensor 1 Diagnosis condition Power switch is ON.
Signal (terminal) Wheel sensor signal
Threshold When difference between the wheel sensors for two or more wheels among all wheel sensors is 6 km/h or more [when driving 100 km/h or less].
Diagnosis delay time 18 seconds or more
2 Diagnosis condition Power switch is ON.
Signal (terminal) Wheel sensor signal
Threshold When difference between the wheel sensors for two or more wheels among all wheel sensors is 6 % or more [when driving 100 km/h or less].
Diagnosis delay time 1 second or less
3 Diagnosis condition Power switch is ON.
Signal (terminal) Wheel sensor signal
Threshold When two or more wheel sensors out of all wheel sensors rotate in different directions.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Front left wheel sensor

  • Front right wheel sensor

  • Rear left wheel sensor

  • Rear right wheel sensor

  • Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E4–64" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E4–64" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK WHEEL SENSOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the each wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

REPLACE WHEEL SENSOR (1)

With CONSULT

  1. Replace the wheel sensor.

    • Front: Refer to FRONT WHEEL SENSOR : Removal & Installation.

    • Rear: Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect 12V battery negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E4–64” detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Check the electrically-driven intelligent brake unit harness connector for disconnection or looseness.

  5. Check the each wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 6.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E4–64” detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E4–64” detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK WHEEL SENSOR HARNESS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect each wheel sensor harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and each wheel sensor harness connector.

    • Measurement connector and terminal for power supply circuit

      Electrically-driven intelligent brake unitWheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 4 B176 (Front left) 1 Existed
      12 E110 (Front right)
      3 B179 (Rear left)
      7 B181 (Rear right)
    • Measurement connector and terminal for signal circuit

      Electrically-driven intelligent brake unitWheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      B64 21 B176 (Front left) 2 Existed
      11 E110 (Front right)
      19 B179 (Rear left)
      15 B181 (Rear right)

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 10.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect each wheel sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E4–64” detected?

YES>>

GO TO 11.

NO>>

INSPECTION END

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect electrically-driven intelligent brake unit harness connector.

  3. Disconnect wheel sensor harness connector.

  4. Connect ABS active wheel sensor tester (SST: J-45741-A) to wheel sensor using appropriate adapter.

  5. Turn the ABS active wheel sensor tester power switch ON.

  6. Spin the wheel of the Nissan Ariya vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

GO TO 12.

REPLACE WHEEL SENSOR

  1. Replace the wheel sensor.

    • Front: Refer to FRONT WHEEL SENSOR : Removal & Installation.

    • Rear: Refer to REAR WHEEL SENSOR : Removal & Installation.

  2. Connect electrically-driven intelligent brake unit harness connector.

  3. Connect 12V battery negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E4–64” detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to Removal and Installation.

NO>>

INSPECTION END

B14e5-64 Adas Control Unit System Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E5 64 Brake control system Diagnosis condition When power switch is ON.
Signal (terminal) Braking force request signal
Threshold When a malfunction is detected in braking force request from ADAS control unit 2.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

ADAS control unit 2

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E5-64" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ADAS CONTROL UNIT 2 SYSTEM

Perform self-diagnosis for “ICC/ADAS 2”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E5-64" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E5-64" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E5-64" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E5-64" detected?

YES ("B14E5-64")>>

Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "B14E5-64")>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

B14e5-92 Adas Control Unit System Nissan Ariya 1st generation

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E5 92 Brake control system Diagnosis condition When power switch is ON.
Signal (terminal) Braking force request signal
Threshold When a malfunction is detected in braking force request from ADAS control unit 2.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E5-92" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ADAS CONTROL UNIT 2 SYSTEM

Perform self-diagnosis for “ICC/ADAS 2”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E5-92" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E5-92" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E5-92" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E5-92" detected?

YES ("B14E5-92")>>

Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "B14E5-92")>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

B14e6-85 Brake Control System Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E6 85 Brake control system 1 Diagnosis condition When power switch is ON.
Signal (terminal) Braking force request signal
Threshold When a malfunction is detected in braking force request from ABS actuator and electric unit (control unit).
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) Braking force request signal
Threshold When a malfunction is detected in braking force request from chassis control module.
Diagnosis delay time 1 second or less
3 Diagnosis condition When power switch is ON.
Signal (terminal) Braking force request signal
Threshold When a malfunction is detected in braking force request from ADAS control unit 2.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • ABS actuator and electric unit (control unit)

  • ADAS control unit 2

  • Chassis control module

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E6-85" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM

Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK ADAS CONTROL UNIT 2 SYSTEM

Perform self-diagnosis for “ICC/ADAS 2”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

CHECK CHASSIS CONTROL MODULE SYSTEM

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 4.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E6-85" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts. GO TO 6.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E6-85" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair / replace harness, connector, or terminal. GO TO 8.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E6-85" detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 10.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E6-85" detected?

YES ("B14E6-85")>>

Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "B14E6-85")>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

B14e6-92 Brake Control System Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B14E6 92 Brake control system 1 Diagnosis condition When power switch is ON.
Signal (terminal) Braking force request signal
Threshold When a malfunction is detected in braking force request from ABS actuator and electric unit (control unit).
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) Braking force request signal
Threshold When a malfunction is detected in braking force request from chassis control module.
Diagnosis delay time 1 second or less
3 Diagnosis condition When power switch is ON.
Signal (terminal) Braking force request signal
Threshold When a malfunction is detected in braking force request from ADAS control unit 2.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • ABS actuator and electric unit (control unit)

  • ADAS control unit 2

  • Chassis control module

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “B14E6-92" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM

Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK ADAS CONTROL UNIT 2 SYSTEM

Perform self-diagnosis for “ICC/ADAS 2”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 3.

CHECK CHASSIS CONTROL MODULE SYSTEM

Perform self-diagnosis for “CHASSIS CONTROL”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 4.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E6-92" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts. GO TO 6.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E6-92" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair / replace harness, connector, or terminal. GO TO 8.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E6-92" detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 10.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "B14E6-92" detected?

YES ("B14E6-92")>>

Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "B14E6-92")>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

C18d0-01 Brake Power Supply Back up Unit Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18D0 01 Backup power supply unit Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (overvoltage).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18D0-01" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D0-01" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D0-01" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D0-01" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18d1-09 Brake Power Supply Back up Unit Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18D1 09 Backup power supply unit Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (charge circuit).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18D1-09" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D1-09" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D1-09" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D1-09" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18d2-12 Brake Power Supply Back up Unit Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18D2 12 Backup power supply unit Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (discharge circuit open).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18D2-12" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D2-12" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D2-12" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D2-12" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18d3-14 Brake Power Supply Back up Unit Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18D3 14 Backup power supply unit Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (discharge circuit short).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18D3-14" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D3-14" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D3-14" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D3-14" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18d4-14 Brake Power Supply Back up Unit Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18D4 14 Backup power supply unit 1 Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (internal cell overvoltage).
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (internal cell short).
Diagnosis delay time 1 second or less
3 Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (internal cell open).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18D4-14" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D4-14" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D4-14" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D4-14" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18d5-09 Brake Power Supply Back up Unit Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18D5 09 Backup power supply unit Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (internal circuit).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18D5-09" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D5-09" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D5-09" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D5-09" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18d6-09 Brake Power Supply Back up Unit Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18D6 09 Backup power supply unit 1 Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (wakeup circuit).
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (response).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18D6-09" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D6-09" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D6-09" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D6-09" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18d7-09 Brake Power Supply Back up Unit Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18D7 09 Backup power supply unit Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (power supply circuit).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Brake power supply backup unit

  • Brake power supply backup unit power supply system

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18D7-09" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D7-09" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D7-09" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D7-09" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18d8-09 Brake Power Supply Back up Unit Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18D8 09 Backup power supply unit Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (internal).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18D8-09" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D8-09" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D8-09" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D8-09" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18d9-09 Brake Power Supply Back up Unit Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18D9 09 Backup power supply unit Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (insulation).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18D9-09" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D9-09" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D9-09" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18D9-09" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18da-09 Brake Power Supply Back up Unit Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18DA 09 Backup power supply unit Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (charge control).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18DA-09" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DA-09" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DA-09" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DA-09" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18db-09 Brake Power Supply Back up Unit Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18DB 09 Backup power supply unit 1 Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (thermistor short).
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (thermistor open).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18DB-09" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DB-09" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DB-09" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DB-09" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18dc-09 Brake Power Supply Back up Unit Nissan Ariya 1st generation

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18DC 09 Backup power supply unit Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (capacitor).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18DC-09" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DC-09" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DC-09" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DC-09" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18dd-09 Brake Power Supply Back up Unit Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18DD 09 Backup power supply unit 1 Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (internal circuit short).
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (internal circuit open).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18DD-09" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DD-09" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DD-09" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DD-09" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18de-82 Brake Power Supply Back up Unit Nissan Ariya 1st generation

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18DE 82 Backup power supply unit communication Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (communication).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector

  • Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18DE-82" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DE-82" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DE-82" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DE-82" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18de-83 Brake Power Supply Back up Unit Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18DE 83 Backup power supply unit communication Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (communication).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Fuse

  • Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18DE-83" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DE-83" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DE-83" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DE-83" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18de-87 Brake Power Supply Back up Unit Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18DE 87 Backup power supply unit communication 1 Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (self-diagnosis).
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When a malfunction is detected in the brake power supply backup unit (communication).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Fuse

  • Brake power supply backup unit

FAIL-SAFE

The following functions are suspended.

Power supply from the brake power supply backup unit

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18DE-87" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DE-87" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DE-87" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18DE-87" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18e1-04 Motor Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E1 04 Motor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in motor.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E1-04" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-04" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-04" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-04" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e1-07 Motor Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E1 07 Motor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in motor speed.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E1-07" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-07" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-07" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-07" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e1-18 Motor Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E1 18 Motor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in motor.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Electrically-driven intelligent brake unit

  • Electrically-driven intelligent brake unit power supply system

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E1-18" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-18" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-18" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-18" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e1-19 Motor Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E1 19 Motor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When the voltage difference between both ends of the motor resistor is 2.0 V or more.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Electrically-driven intelligent brake unit

  • Electrically-driven intelligent brake unit power supply system

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E1-19" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-19" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-19" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-19" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e1-49 Motor Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E1 49 Motor 1 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in motor current.
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When the motor position is not detected.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Electrically-driven intelligent brake unit

  • Electrically-driven intelligent brake unit power supply system

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E1-49" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-49" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-49" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-49" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e1-4b Motor Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E1 4B Motor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in motor temperature.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E1-4B" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-4B" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-4B" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E1-4B" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e3-86 Abs Actuator and Electric Unit (control Unit) System Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E3 86 VDC system Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When ABS actuator and electric unit (control unit) transmission signal is malfunction.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E3-86" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM

Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E3-86" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E3-86" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E3-86" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E3-86" detected?

YES ("C18E3-86")>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "C18E3-86")>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

C18e4-88 Can Comm Circuit Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E4 88 CAN communication system 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When electrically-driven intelligent brake unit CAN communication signal transmission is malfunction.
Diagnosis delay time 2 seconds or more
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When electrically-driven intelligent brake unit CAN communication signal reception is malfunction.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Harness or connector

  • CAN communication line

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E4-88" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness, connector, or terminal. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E4-88" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E4-88" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e5-88 Can Comm Circuit Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E5 88 CAN communication system 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When electrically-driven intelligent brake unit CAN communication signal transmission is malfunction.
Diagnosis delay time 2 seconds or more
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When electrically-driven intelligent brake unit CAN communication signal reception is malfunction.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Harness or connector

  • CAN communication line

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E5-88" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness, connector, or terminal. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E5-88" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E5-88" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e6-49 Can Comm System Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E6 49 CAN communication system 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When electrically-driven intelligent brake unit CAN communication signal transmission is malfunction.
Diagnosis delay time 2 seconds or more
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When electrically-driven intelligent brake unit CAN communication signal reception is malfunction.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Harness or connector

  • CAN communication line

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E6-49" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness, connector, or terminal. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E6-49" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E6-49" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e7-13 Power Supply Circuit Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E7 13 Power supply system Diagnosis condition When power switch is ON.
Signal (terminal) Power switch ON signal
Threshold When a malfunction is detected in power switch ON signal.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • BCM

  • Ignition switch

  • Electrically-driven intelligent brake unit

  • Electrically-driven intelligent brake unit power supply system

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E7-13" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK BCM SYSTEM

Perform self-diagnosis for “BCM”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-13" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-13" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-13" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-13" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e7-16 Power Supply Circuit Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E7 16 Power supply system Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When electrically-driven intelligent brake unit power supply voltage is 6.0 V ore less.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Electrically-driven intelligent brake unit

  • Electrically-driven intelligent brake unit power supply system

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E7-16" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK BCM SYSTEM

Perform self-diagnosis for “BCM”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-16" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-16" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-16" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-16" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e7-17 Power Supply Circuit Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E7 17 Power supply system Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When electrically-driven intelligent brake unit power supply voltage is 27.5 V or more.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Electrically-driven intelligent brake unit

  • Electrically-driven intelligent brake unit power supply system

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E7-17" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK BCM SYSTEM

Perform self-diagnosis for “BCM”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-17" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-17" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-17" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-17" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e7-1c Power Supply Circuit Nissan Ariya 1st generation

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E7 1C Power supply system 1 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When electrically-driven intelligent brake unit power supply voltage is less than 9.3 V.
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When electrically-driven intelligent brake unit power supply voltage is less than 7.5 V.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Electrically-driven intelligent brake unit

  • Electrically-driven intelligent brake unit power supply system

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E7-1C" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK BCM SYSTEM

Perform self-diagnosis for “BCM”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-1C" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-1C" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-1C" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E7-1C" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e9-01 Control Module Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E9 01 Control module Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When an internal malfunction is detected in electrically-driven intelligent brake unit (microcomputer).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E9-01" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-01" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-01" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-01" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e9-04 Control Module Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E9 04 Control module Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When an internal malfunction is detected in electrically-driven intelligent brake unit (software).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E9-04" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-04" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-04" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-04" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e9-44 Control Module Nissan Ariya 1st generation

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E9 44 Control module Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When an internal malfunction is detected in electrically-driven intelligent brake unit (RAM).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E9-44" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-44" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-44" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-44" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e9-45 Control Module Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E9 45 Control module Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When an internal malfunction is detected in electrically-driven intelligent brake unit (ROM).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E9-45" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-45" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-45" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-45" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e9-46 Control Module Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E9 46 Control module 1 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When an internal malfunction is detected in electrically-driven intelligent brake unit (motor control).
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When an internal malfunction is detected in electrically-driven intelligent brake unit (memory).
Diagnosis delay time 1 second or less
3 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When an internal malfunction is detected in electrically-driven intelligent brake unit (rotor position control).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E9-46" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-46" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-46" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-46" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e9-47 Control Module Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E9 47 Control module 1 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When an internal malfunction is detected in electrically-driven intelligent brake unit (processor).
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When an internal malfunction is detected in electrically-driven intelligent brake unit (fail-safe control).
Diagnosis delay time 1 second or less
3 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When an internal malfunction is detected in electrically-driven intelligent brake unit (internal communication).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E9-47" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-47" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-47" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-47" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e9-48 Control Module Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E9 48 Control module Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When an internal malfunction is detected in electrically-driven intelligent brake unit (microcomputer).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E9-48" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-48" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-48" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-48" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e9-49 Control Module Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E9 49 Control module Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When an internal malfunction is detected in electrically-driven intelligent brake unit (initialize).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E9-49" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-49" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-49" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-49" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18e9-96 Control Module Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18E9 96 Control module Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When an internal malfunction is detected in electrically-driven intelligent brake unit (AD converter).
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18E9-96" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-96" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-96" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18E9-96" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ea-01 Abs Actuator and Electric Unit (control Unit) System Nissan Ariya 1st generation

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EA 01 VDC system Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When brake fluid pressure signal from ABS actuator and electric unit (control unit) is malfunction.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EA-01" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM

Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EA-01" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EA-01" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EA-01" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EA-01" detected?

YES ("C18EA-01")>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "C18EA-01")>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

C18eb-01 Brake Power Supply Back up Unit Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EB 01 Backup power supply unit 1 Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When brake power supply backup unit power supply voltage is 7.5 V or less.
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) Brake power supply backup unit signal
Threshold When brake power supply backup unit power supply voltage is 9.0 V or less (when brake operation is not request).
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Brake power supply backup unit

  • Brake power supply backup unit power supply system

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EB-01" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EB-01" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect brake power supply backup unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect brake power supply backup unit harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EB-01" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect brake power supply backup unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Disconnect 12V battery cable from negative terminal.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EB-01" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (1)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Disconnect brake power supply backup unit harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B642
    17 B94 1 Existed
    4 Not existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 1 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector. GO TO 8.

CHECK BRAKE POWER SUPPLY BACKUP UNIT POWER SUPPLY CIRCUIT (2)

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Perform trouble diagnosis for 12V battery power supply.

CHECK BRAKE POWER SUPPLY BACKUP UNIT COMMUNICATION CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B642

    4*1

    5*2
    B94 1 Not existed
    4 Not existed
    5 Existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 5 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 10.

CHECK BRAKE POWER SUPPLY BACKUP UNIT WAKE UP CIRCUIT

  1. Check the continuity between electrically-driven intelligent brake unit and brake power supply backup unit.

    Electrically-driven intelligent brake unitBrake power supply backup unitContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B642
    24 B94 1 Not existed
    4 Existed
    5 Not existed
    6 Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  2. Check the continuity between brake power supply backup unit and ground.

    Brake power supply backup unit—Continuity
    ConnectorTerminal
    B94 4 Ground Not existed

Is the inspection result normal?

YES>>

Replace the brake power supply backup unit. Refer to BRAKE POWER SUPPLY BACKUP UNIT : Removal & Installation.

NO>>

Repair / replace harness or connector.

C18ec-01 Stroke Sensor Nissan Ariya 1st generation

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EC 01 Stroke sensor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in stroke sensor output.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EC-01" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-01" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect stroke sensor harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect stroke sensor harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-01" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect stroke sensor harness connector.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Disconnect 12V battery cable from negative terminal.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-01" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE PEDAL HEIGHT

Check each brake pedal height. Refer to BRAKE PEDAL : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Adjust each height. Refer to BRAKE PEDAL : Periodic Maintenance Operation. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-01" detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK STROKE SENSOR CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and electrically-driven intelligent brake unit.

    Stroke sensorElectrically-driven intelligent brake unitContinuity
    ConnectorTerminalConnectorTerminal
    B39 3

    B63*1

    B64*2
    23 Existed
    3 2 Not existed
    3 22 Not existed
    3 8 Not existed
    2 23 Not existed
    2 2 Existed
    2 22 Not existed
    2 8 Not existed
    1 23 Not existed
    1 2 Not existed
    1 22 Existed
    1 8 Not existed
    4 23 Not existed
    4 2 Not existed
    4 22 Not existed
    4 8 Existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 12.

CHECK STROKE SENSOR POWER SUPPLY

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Check the stroke sensor power voltage.

    +—Voltage
    Stroke sensor
    ConnectorTerminal
    B39 2 Ground 4.8 - 5.15 V

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace error-detected parts. GO TO 11.

CHECK STROKE SENSOR GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and ground.

    Stroke sensor—Continuity
    ConnectorTerminal
    B39 4 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 12.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-01" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ec-04 Stroke Sensor Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EC 04 Stroke sensor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in stroke sensor output.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EC-04" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-04" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect stroke sensor harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect stroke sensor harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-04" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect stroke sensor harness connector.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Disconnect 12V battery cable from negative terminal.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-04" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE PEDAL HEIGHT

Check each brake pedal height. Refer to BRAKE PEDAL : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Adjust each height. Refer to BRAKE PEDAL : Periodic Maintenance Operation. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-04" detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK STROKE SENSOR CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and electrically-driven intelligent brake unit.

    Stroke sensorElectrically-driven intelligent brake unitContinuity
    ConnectorTerminalConnectorTerminal
    B39 3

    B63*1

    B64*2
    23 Existed
    3 2 Not existed
    3 22 Not existed
    3 8 Not existed
    2 23 Not existed
    2 2 Existed
    2 22 Not existed
    2 8 Not existed
    1 23 Not existed
    1 2 Not existed
    1 22 Existed
    1 8 Not existed
    4 23 Not existed
    4 2 Not existed
    4 22 Not existed
    4 8 Existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 12.

CHECK STROKE SENSOR POWER SUPPLY

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Check the stroke sensor power voltage.

    +—Voltage
    Stroke sensor
    ConnectorTerminal
    B39 2 Ground 4.8 - 5.15 V

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace error-detected parts. GO TO 11.

CHECK STROKE SENSOR GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and ground.

    Stroke sensor—Continuity
    ConnectorTerminal
    B39 4 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 12.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-04" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ec-11 Stroke Sensor Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EC 11 Stroke sensor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in stroke sensor internal circuit.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EC-11" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-11" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect stroke sensor harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect stroke sensor harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-11" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect stroke sensor harness connector.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Disconnect 12V battery cable from negative terminal.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-11" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE PEDAL HEIGHT

Check each brake pedal height. Refer to BRAKE PEDAL : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Adjust each height. Refer to BRAKE PEDAL : Periodic Maintenance Operation. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-11" detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK STROKE SENSOR CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and electrically-driven intelligent brake unit.

    Stroke sensorElectrically-driven intelligent brake unitContinuity
    ConnectorTerminalConnectorTerminal
    B39 3

    B63*1

    B64*2
    23 Existed
    3 2 Not existed
    3 22 Not existed
    3 8 Not existed
    2 23 Not existed
    2 2 Existed
    2 22 Not existed
    2 8 Not existed
    1 23 Not existed
    1 2 Not existed
    1 22 Existed
    1 8 Not existed
    4 23 Not existed
    4 2 Not existed
    4 22 Not existed
    4 8 Existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 12.

CHECK STROKE SENSOR POWER SUPPLY

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Check the stroke sensor power voltage.

    +—Voltage
    Stroke sensor
    ConnectorTerminal
    B39 2 Ground 4.8 - 5.15 V

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace error-detected parts. GO TO 11.

CHECK STROKE SENSOR GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and ground.

    Stroke sensor—Continuity
    ConnectorTerminal
    B39 4 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 12.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-11" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ec-12 Stroke Sensor Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EC 12 Stroke sensor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in stroke sensor internal circuit.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EC-12" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-12" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect stroke sensor harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect stroke sensor harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-12" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect stroke sensor harness connector.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Disconnect 12V battery cable from negative terminal.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-12" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE PEDAL HEIGHT

Check each brake pedal height. Refer to BRAKE PEDAL : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Adjust each height. Refer to BRAKE PEDAL : Periodic Maintenance Operation. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-12" detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK STROKE SENSOR CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and electrically-driven intelligent brake unit.

    Stroke sensorElectrically-driven intelligent brake unitContinuity
    ConnectorTerminalConnectorTerminal
    B39 3

    B63*1

    B64*2
    23 Existed
    3 2 Not existed
    3 22 Not existed
    3 8 Not existed
    2 23 Not existed
    2 2 Existed
    2 22 Not existed
    2 8 Not existed
    1 23 Not existed
    1 2 Not existed
    1 22 Existed
    1 8 Not existed
    4 23 Not existed
    4 2 Not existed
    4 22 Not existed
    4 8 Existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 12.

CHECK STROKE SENSOR POWER SUPPLY

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Check the stroke sensor power voltage.

    +—Voltage
    Stroke sensor
    ConnectorTerminal
    B39 2 Ground 4.8 - 5.15 V

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace error-detected parts. GO TO 11.

CHECK STROKE SENSOR GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and ground.

    Stroke sensor—Continuity
    ConnectorTerminal
    B39 4 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 12.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-12" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ec-13 Stroke Sensor Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EC 13 Stroke sensor 1 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When stroke sensor power supply is 4.8 V or less.
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When stroke sensor power supply is 5.18 V or more.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Electrically-driven intelligent brake unit

  • Electrically-driven intelligent brake unit power supply system

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EC-13" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-13" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect stroke sensor harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect stroke sensor harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-13" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect stroke sensor harness connector.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Disconnect 12V battery cable from negative terminal.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-13" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE PEDAL HEIGHT

Check each brake pedal height. Refer to BRAKE PEDAL : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Adjust each height. Refer to BRAKE PEDAL : Periodic Maintenance Operation. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-13" detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK STROKE SENSOR CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and electrically-driven intelligent brake unit.

    Stroke sensorElectrically-driven intelligent brake unitContinuity
    ConnectorTerminalConnectorTerminal
    B39 3

    B63*1

    B64*2
    23 Existed
    3 2 Not existed
    3 22 Not existed
    3 8 Not existed
    2 23 Not existed
    2 2 Existed
    2 22 Not existed
    2 8 Not existed
    1 23 Not existed
    1 2 Not existed
    1 22 Existed
    1 8 Not existed
    4 23 Not existed
    4 2 Not existed
    4 22 Not existed
    4 8 Existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 12.

CHECK STROKE SENSOR POWER SUPPLY

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Check the stroke sensor power voltage.

    +—Voltage
    Stroke sensor
    ConnectorTerminal
    B39 2 Ground 4.8 - 5.15 V

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace error-detected parts. GO TO 11.

CHECK STROKE SENSOR GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and ground.

    Stroke sensor—Continuity
    ConnectorTerminal
    B39 4 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 12.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-13" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ec-14 Stroke Sensor Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EC 14 Stroke sensor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in stroke sensor internal circuit.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EC-14" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-14" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect stroke sensor harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect stroke sensor harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-14" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect stroke sensor harness connector.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Disconnect 12V battery cable from negative terminal.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-14" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE PEDAL HEIGHT

Check each brake pedal height. Refer to BRAKE PEDAL : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Adjust each height. Refer to BRAKE PEDAL : Periodic Maintenance Operation. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-14" detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK STROKE SENSOR CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and electrically-driven intelligent brake unit.

    Stroke sensorElectrically-driven intelligent brake unitContinuity
    ConnectorTerminalConnectorTerminal
    B39 3

    B63*1

    B64*2
    23 Existed
    3 2 Not existed
    3 22 Not existed
    3 8 Not existed
    2 23 Not existed
    2 2 Existed
    2 22 Not existed
    2 8 Not existed
    1 23 Not existed
    1 2 Not existed
    1 22 Existed
    1 8 Not existed
    4 23 Not existed
    4 2 Not existed
    4 22 Not existed
    4 8 Existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 12.

CHECK STROKE SENSOR POWER SUPPLY

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Check the stroke sensor power voltage.

    +—Voltage
    Stroke sensor
    ConnectorTerminal
    B39 2 Ground 4.8 - 5.15 V

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace error-detected parts. GO TO 11.

CHECK STROKE SENSOR GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and ground.

    Stroke sensor—Continuity
    ConnectorTerminal
    B39 4 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 12.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-14" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ec-15 Stroke Sensor Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EC 15 Stroke sensor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in stroke sensor internal circuit.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EC-15" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-15" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect stroke sensor harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect stroke sensor harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-15" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect stroke sensor harness connector.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Disconnect 12V battery cable from negative terminal.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-15" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE PEDAL HEIGHT

Check each brake pedal height. Refer to BRAKE PEDAL : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Adjust each height. Refer to BRAKE PEDAL : Periodic Maintenance Operation. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-15" detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK STROKE SENSOR CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and electrically-driven intelligent brake unit.

    Stroke sensorElectrically-driven intelligent brake unitContinuity
    ConnectorTerminalConnectorTerminal
    B39 3

    B63*1

    B64*2
    23 Existed
    3 2 Not existed
    3 22 Not existed
    3 8 Not existed
    2 23 Not existed
    2 2 Existed
    2 22 Not existed
    2 8 Not existed
    1 23 Not existed
    1 2 Not existed
    1 22 Existed
    1 8 Not existed
    4 23 Not existed
    4 2 Not existed
    4 22 Not existed
    4 8 Existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 12.

CHECK STROKE SENSOR POWER SUPPLY

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Check the stroke sensor power voltage.

    +—Voltage
    Stroke sensor
    ConnectorTerminal
    B39 2 Ground 4.8 - 5.15 V

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace error-detected parts. GO TO 11.

CHECK STROKE SENSOR GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and ground.

    Stroke sensor—Continuity
    ConnectorTerminal
    B39 4 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 12.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-15" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ec-1f Stroke Sensor Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EC 1F Stroke sensor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in stroke sensor signal circuit.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EC-1F" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-1F" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect stroke sensor harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect stroke sensor harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-1F" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect stroke sensor harness connector.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Disconnect 12V battery cable from negative terminal.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-1F" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE PEDAL HEIGHT

Check each brake pedal height. Refer to BRAKE PEDAL : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Adjust each height. Refer to BRAKE PEDAL : Periodic Maintenance Operation. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-1F" detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK STROKE SENSOR CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and electrically-driven intelligent brake unit.

    Stroke sensorElectrically-driven intelligent brake unitContinuity
    ConnectorTerminalConnectorTerminal
    B39 3

    B63*1

    B64*2
    23 Existed
    3 2 Not existed
    3 22 Not existed
    3 8 Not existed
    2 23 Not existed
    2 2 Existed
    2 22 Not existed
    2 8 Not existed
    1 23 Not existed
    1 2 Not existed
    1 22 Existed
    1 8 Not existed
    4 23 Not existed
    4 2 Not existed
    4 22 Not existed
    4 8 Existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 12.

CHECK STROKE SENSOR POWER SUPPLY

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Check the stroke sensor power voltage.

    +—Voltage
    Stroke sensor
    ConnectorTerminal
    B39 2 Ground 4.8 - 5.15 V

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace error-detected parts. GO TO 11.

CHECK STROKE SENSOR GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and ground.

    Stroke sensor—Continuity
    ConnectorTerminal
    B39 4 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 12.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EC-1F" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ed-04 Motor Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18ED 04 Motor power supply Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in motor voltage.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Electrically-driven intelligent brake unit

  • Electrically-driven intelligent brake unit power supply system

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18ED-04" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18ED-04" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18ED-04" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18ED-04" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ee-01 Stroke Sensor Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EE 01 Stroke sensor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When stroke sensor value is out of range.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EE-01" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-01" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect stroke sensor harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect stroke sensor harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-01" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect stroke sensor harness connector.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Disconnect 12V battery cable from negative terminal.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-01" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE PEDAL HEIGHT

Check each brake pedal height. Refer to BRAKE PEDAL : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Adjust each height. Refer to BRAKE PEDAL : Periodic Maintenance Operation. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-01" detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK STROKE SENSOR CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and electrically-driven intelligent brake unit.

    Stroke sensorElectrically-driven intelligent brake unitContinuity
    ConnectorTerminalConnectorTerminal
    B39 3

    B63*1

    B64*2
    23 Existed
    3 2 Not existed
    3 22 Not existed
    3 8 Not existed
    2 23 Not existed
    2 2 Existed
    2 22 Not existed
    2 8 Not existed
    1 23 Not existed
    1 2 Not existed
    1 22 Existed
    1 8 Not existed
    4 23 Not existed
    4 2 Not existed
    4 22 Not existed
    4 8 Existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 12.

CHECK STROKE SENSOR POWER SUPPLY

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Check the stroke sensor power voltage.

    +—Voltage
    Stroke sensor
    ConnectorTerminal
    B39 2 Ground 4.8 - 5.15 V

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace error-detected parts. GO TO 11.

CHECK STROKE SENSOR GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and ground.

    Stroke sensor—Continuity
    ConnectorTerminal
    B39 4 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 12.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-01" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ee-04 Stroke Sensor Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EE 04 Stroke sensor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When stroke sensor value is out of range.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EE-04" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-04" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect stroke sensor harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect stroke sensor harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-04" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect stroke sensor harness connector.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Disconnect 12V battery cable from negative terminal.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-04" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE PEDAL HEIGHT

Check each brake pedal height. Refer to BRAKE PEDAL : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Adjust each height. Refer to BRAKE PEDAL : Periodic Maintenance Operation. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-04" detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK STROKE SENSOR CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and electrically-driven intelligent brake unit.

    Stroke sensorElectrically-driven intelligent brake unitContinuity
    ConnectorTerminalConnectorTerminal
    B39 3

    B63*1

    B64*2
    23 Existed
    3 2 Not existed
    3 22 Not existed
    3 8 Not existed
    2 23 Not existed
    2 2 Existed
    2 22 Not existed
    2 8 Not existed
    1 23 Not existed
    1 2 Not existed
    1 22 Existed
    1 8 Not existed
    4 23 Not existed
    4 2 Not existed
    4 22 Not existed
    4 8 Existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 12.

CHECK STROKE SENSOR POWER SUPPLY

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Check the stroke sensor power voltage.

    +—Voltage
    Stroke sensor
    ConnectorTerminal
    B39 2 Ground 4.8 - 5.15 V

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace error-detected parts. GO TO 11.

CHECK STROKE SENSOR GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and ground.

    Stroke sensor—Continuity
    ConnectorTerminal
    B39 4 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 12.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-04" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ee-64 Stroke Sensor Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EE 64 Stroke sensor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in stroke sensor.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EE-64" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-64" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect stroke sensor harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect stroke sensor harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-64" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect stroke sensor harness connector.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Disconnect 12V battery cable from negative terminal.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-64" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE PEDAL HEIGHT

Check each brake pedal height. Refer to BRAKE PEDAL : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Adjust each height. Refer to BRAKE PEDAL : Periodic Maintenance Operation. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-64" detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK STROKE SENSOR CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and electrically-driven intelligent brake unit.

    Stroke sensorElectrically-driven intelligent brake unitContinuity
    ConnectorTerminalConnectorTerminal
    B39 3

    B63*1

    B64*2
    23 Existed
    3 2 Not existed
    3 22 Not existed
    3 8 Not existed
    2 23 Not existed
    2 2 Existed
    2 22 Not existed
    2 8 Not existed
    1 23 Not existed
    1 2 Not existed
    1 22 Existed
    1 8 Not existed
    4 23 Not existed
    4 2 Not existed
    4 22 Not existed
    4 8 Existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 12.

CHECK STROKE SENSOR POWER SUPPLY

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Check the stroke sensor power voltage.

    +—Voltage
    Stroke sensor
    ConnectorTerminal
    B39 2 Ground 4.8 - 5.15 V

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace error-detected parts. GO TO 11.

CHECK STROKE SENSOR GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and ground.

    Stroke sensor—Continuity
    ConnectorTerminal
    B39 4 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 12.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-64" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ee-87 Stroke Sensor Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EE 87 Stroke sensor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in stroke sensor.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EE-87" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-87" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect stroke sensor harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect stroke sensor harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-87" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect stroke sensor harness connector.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Disconnect 12V battery cable from negative terminal.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-87" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE PEDAL HEIGHT

Check each brake pedal height. Refer to BRAKE PEDAL : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Adjust each height. Refer to BRAKE PEDAL : Periodic Maintenance Operation. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-87" detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK STROKE SENSOR CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and electrically-driven intelligent brake unit.

    Stroke sensorElectrically-driven intelligent brake unitContinuity
    ConnectorTerminalConnectorTerminal
    B39 3

    B63*1

    B64*2
    23 Existed
    3 2 Not existed
    3 22 Not existed
    3 8 Not existed
    2 23 Not existed
    2 2 Existed
    2 22 Not existed
    2 8 Not existed
    1 23 Not existed
    1 2 Not existed
    1 22 Existed
    1 8 Not existed
    4 23 Not existed
    4 2 Not existed
    4 22 Not existed
    4 8 Existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 12.

CHECK STROKE SENSOR POWER SUPPLY

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Check the stroke sensor power voltage.

    +—Voltage
    Stroke sensor
    ConnectorTerminal
    B39 2 Ground 4.8 - 5.15 V

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace error-detected parts. GO TO 11.

CHECK STROKE SENSOR GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and ground.

    Stroke sensor—Continuity
    ConnectorTerminal
    B39 4 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 12.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-87" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ee-96 Stroke Sensor Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EE 96 Stroke sensor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in stroke sensor offset.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EE-96" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-96" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

  5. Disconnect stroke sensor harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect stroke sensor harness connector.

  3. Connect 12V battery cable to negative terminal.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Power switch OFF and disconnect CONSULT from data link connector.

  6. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  7. Power switch OFF to ON without depressing the brake pedal.

  8. Erase self-diagnosis result for “BRAKE”.

  9. Power switch OFF and disconnect CONSULT from data link connector.

  10. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  11. Power switch OFF to ON without depressing the brake pedal.

  12. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-96" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Connect stroke sensor harness connector.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Disconnect 12V battery cable from negative terminal.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-96" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK BRAKE PEDAL HEIGHT

Check each brake pedal height. Refer to BRAKE PEDAL : Periodic Maintenance Operation.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Adjust each height. Refer to BRAKE PEDAL : Periodic Maintenance Operation. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-96" detected?

YES>>

GO TO 9.

NO>>

INSPECTION END

CHECK STROKE SENSOR CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and electrically-driven intelligent brake unit.

    Stroke sensorElectrically-driven intelligent brake unitContinuity
    ConnectorTerminalConnectorTerminal
    B39 3

    B63*1

    B64*2
    23 Existed
    3 2 Not existed
    3 22 Not existed
    3 8 Not existed
    2 23 Not existed
    2 2 Existed
    2 22 Not existed
    2 8 Not existed
    1 23 Not existed
    1 2 Not existed
    1 22 Existed
    1 8 Not existed
    4 23 Not existed
    4 2 Not existed
    4 22 Not existed
    4 8 Existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness or connector. GO TO 12.

CHECK STROKE SENSOR POWER SUPPLY

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Check the stroke sensor power voltage.

    +—Voltage
    Stroke sensor
    ConnectorTerminal
    B39 2 Ground 4.8 - 5.15 V

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace error-detected parts. GO TO 11.

CHECK STROKE SENSOR GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect stroke sensor harness connector.

  5. Disconnect electrically-driven intelligent brake unit harness connector.

  6. Check the continuity between stroke sensor harness connector and ground.

    Stroke sensor—Continuity
    ConnectorTerminal
    B39 4 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair / replace harness or connector. GO TO 12.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable from negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EE-96" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ef-16 Rotor Position Sensor Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EF 16 Rotor position sensor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in rotor position sensor signal.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EF-16" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EF-16" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EF-16" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EF-16" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ef-17 Rotor Position Sensor Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EF 17 Rotor position sensor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in rotor position sensor signal.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EF-17" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EF-17" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EF-17" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EF-17" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18ef-96 Rotor Position Sensor Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18EF 96 Rotor position sensor Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in rotor position sensor signal.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18EF-96" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EF-96" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EF-96" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18EF-96" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18f1-08 Vdc System Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18F1 08 VDC system Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in Nissan Ariya vehicle speed signal.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18F1-08" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM

Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F1-08" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F1-08" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F1-08" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F1-08" detected?

YES ("C18F1-08")>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "C18F1-08")>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

C18f3-04 Overheat Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18F3 04 Overheat Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When the control module temperature is 123 ℃ (253.4℉) to 142℃ (287.6℉) after 6.5 seconds at 123℃ (253.4℉) or more.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18F3-04" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F3-04" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F3-04" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F3-04" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK DATA MONITOR

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Select “BRAKE”, “Data monitor” according this order.

  3. Check "Temperature 1" and "Temperature 2". Refer to Values On The Diagnosis Tool.

Is "Temperature " -50℃ (-58℉) or less, or 125℃ (257℉) or more?

YES>>

GO TO 8.

NO>>

GO TO 9.

CHECK MOTOR ROOM

Check for any locations of abnormal heating around the electrically-driven intelligent brake unit.

Are there any heated locations?

YES>>

Perform diagnosis of the heated locations, and wait for the temperature to fall. GO TO 9.

NO>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F3-04" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18f3-4b Overheat Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18F3 4B Overheat Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When the control module temperature is 142℃ (287.6℉) or more after 6.5 seconds at 123℃ (253.4℉) or more.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

  • Boost function [Boost operation by the ABS actuator and electric unit (control unit) is activated]

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18F3-4B" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F3-4B" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F3-4B" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F3-4B" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK DATA MONITOR

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Select “BRAKE”, “Data monitor” according this order.

  3. Check "Temperature 1" and "Temperature 2". Refer to Values On The Diagnosis Tool.

Is "Temperature " -50℃ (-58℉) or less, or 125℃ (257℉) or more?

YES>>

GO TO 8.

NO>>

GO TO 9.

CHECK MOTOR ROOM

Check for any locations of abnormal heating around the electrically-driven intelligent brake unit.

Are there any heated locations?

YES>>

Perform diagnosis of the heated locations, and wait for the temperature to fall. GO TO 9.

NO>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F3-4B" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18f4-86 Bcm System Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18F4 86 BCM communication 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in BCM system.
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in BCM signal.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • BCM

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18F4-86" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK BCM SYSTEM

Perform self-diagnosis for “BCM”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F4-86" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F4-86" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F4-86" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F4-86" detected?

YES ("C18F4-86")>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "C18F4-86")>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

C18f5-08 Ipdm E/r System Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18F5 08 IPDM E/R communication Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in IPDM E/R system.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • IPDM E/R

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18F5-08" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK IPDM E/R SYSTEM

Perform self-diagnosis for “IPDM E/R”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F5-08" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F5-08" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F5-08" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F5-08" detected?

YES ("C18F5-08")>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "C18F5-08")>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

C18f6-08 Vcm System Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18F6 08 VCM/ECM/HPCM communication Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in VCM system.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • VCM

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18F6-08" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK VCM SYSTEM

Perform self-diagnosis for “EV/HEV”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F6-08" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F6-08" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F6-08" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F6-08" detected?

YES ("C18F6-08")>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "C18F6-08")>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

C18f7-08 Abs Actuator and Electric Unit (control Unit) System Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18F7 08 ABS communication Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in ABS actuator and electric unit (control unit) system.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • ABS actuator and electric unit (control unit)

  • CAN communication line

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18F7-08" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM

Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F7-08" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F7-08" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F7-08" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F7-08" detected?

YES ("C18F7-08")>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "C18F7-08")>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

C18f7-86 Abs Actuator and Electric Unit (control Unit) System Nissan Ariya 1st generation

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18F7 86 ABS communication 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in ABS actuator and electric unit (control unit) system.
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in brake pedal depress force.
Diagnosis delay time 1 second or less
3 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in brake caliper.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • ABS actuator and electric unit (control unit)

  • Brake caliper

  • CAN communication line

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18F7-86" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM

Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F7-86" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F7-86" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F7-86" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F7-86" detected?

YES ("C18F7-86")>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "C18F7-86")>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

C18f8-08 Vcm System Nissan Ariya 1st generation

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18F8 08 VCM/ECM/HPCM communication Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in VCM signal.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • VCM

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18F8-08" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK VCM SYSTEM

Perform self-diagnosis for “EV/HEV”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F8-08" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F8-08" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F8-08" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F8-08" detected?

YES ("C18F8-08")>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "C18F8-08")>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

C18f8-86 Vcm System Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18F8 86 VCM/ECM/HPCM communication Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in VCM signal.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • VCM

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18F8-86" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK VCM SYSTEM

Perform self-diagnosis for “EV/HEV”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F8-86" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F8-86" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F8-86" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F8-86" detected?

YES ("C18F8-86")>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "C18F8-86")>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

C18f9-02 Abs Actuator and Electric Unit (control Unit) System Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18F9 02 VDC system Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in brake pedal signal.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • ABS actuator and electric unit (control unit)

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18F9-02" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM

Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F9-02" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F9-02" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair / replace harness, connector, or terminal. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F9-02" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 8.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18F9-02" detected?

YES ("C18F9-02")>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

YES (Other than "C18F9-02")>>

Check the DTC. Refer to DTC Index.

NO>>

INSPECTION END

C18fa-44 Programing Incomplete Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18FA 44 Calibration incomplete Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When programming data is not same.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Programing is not complete

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18FA-44" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM PROGRAMMING

With CONSULT

Perform programming. Refer to Work Procedure.

>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FA-44" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18fa-46 Programing Incomplete Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18FA 46 Calibration incomplete Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When programming is incomplete.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Programing is not complete

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18FA-46" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM PROGRAMMING

With CONSULT

Perform programming. Refer to Work Procedure.

>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE” after record or print self-diagnosis results and freeze frame data (FFD).

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FA-46" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18fc-18 Temperature Sensor Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18FC 18 Temperature sensor 1 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in temperature sensor [-43.6℃ (-46.48℉) or less].
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in temperature sensor [169℃ (336.2℉) or more].
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18FC-18" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FC-18" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FC-18" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FC-18" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK DATA MONITOR

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Select “BRAKE”, “Data monitor” according this order.

  3. Check "Temperature 1" and "Temperature 2". Refer to Values On The Diagnosis Tool.

Is "Temperature " -50℃ (-58℉) or less, or 125℃ (257℉) or more?

YES>>

GO TO 8.

NO>>

GO TO 9.

CHECK MOTOR ROOM

Check for any locations of abnormal heating around the electrically-driven intelligent brake unit.

Are there any heated locations?

YES>>

Perform diagnosis of the heated locations, and wait for the temperature to fall. GO TO 9.

NO>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FC-18" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18fc-19 Temperature Sensor Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18FC 19 Temperature sensor 1 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in temperature sensor [-43.6℃ (-46.48℉) or less].
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in temperature sensor [169℃ (336.2℉) or more].
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18FC-19" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FC-19" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FC-19" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FC-19" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK DATA MONITOR

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Select “BRAKE”, “Data monitor” according this order.

  3. Check "Temperature 1" and "Temperature 2". Refer to Values On The Diagnosis Tool.

Is "Temperature " -50℃ (-58℉) or less, or 125℃ (257℉) or more?

YES>>

GO TO 8.

NO>>

GO TO 9.

CHECK MOTOR ROOM

Check for any locations of abnormal heating around the electrically-driven intelligent brake unit.

Are there any heated locations?

YES>>

Perform diagnosis of the heated locations, and wait for the temperature to fall. GO TO 9.

NO>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FC-19" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18fd-18 Temperature Sensor Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18FD 18 Temperature sensor 1 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in temperature sensor [-43.6℃ (-46.48℉) or less].
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in temperature sensor [169℃ (336.2℉) or more].
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18FD-18" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FD-18" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FD-18" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FD-18" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK DATA MONITOR

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Select “BRAKE”, “Data monitor” according this order.

  3. Check "Temperature 1" and "Temperature 2". Refer to Values On The Diagnosis Tool.

Is "Temperature " -50℃ (-58℉) or less, or 125℃ (257℉) or more?

YES>>

GO TO 8.

NO>>

GO TO 9.

CHECK MOTOR ROOM

Check for any locations of abnormal heating around the electrically-driven intelligent brake unit.

Are there any heated locations?

YES>>

Perform diagnosis of the heated locations, and wait for the temperature to fall. GO TO 9.

NO>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FD-18" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18fd-19 Temperature Sensor Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18FD 19 Temperature sensor 1 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in temperature sensor [-43.6℃ (-46.48℉) or less].
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When a malfunction is detected in temperature sensor [169℃ (336.2℉) or more].
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18FD-19" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FD-19" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FD-19" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FD-19" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK DATA MONITOR

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Select “BRAKE”, “Data monitor” according this order.

  3. Check "Temperature 1" and "Temperature 2". Refer to Values On The Diagnosis Tool.

Is "Temperature " -50℃ (-58℉) or less, or 125℃ (257℉) or more?

YES>>

GO TO 8.

NO>>

GO TO 9.

CHECK MOTOR ROOM

Check for any locations of abnormal heating around the electrically-driven intelligent brake unit.

Are there any heated locations?

YES>>

Perform diagnosis of the heated locations, and wait for the temperature to fall. GO TO 9.

NO>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FD-19" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

C18fe-29 Temperature Sensor Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
C18FE 29 Temperature sensor 1 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When the difference each temperature sensor is 3.2 V or less.
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When the difference each temperature sensor is 3.4 V or more.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

Electrically-driven intelligent brake unit

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “C18FE-29" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Check the 12V battery terminal connections.

  4. Check the 12V battery.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts. GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

With CONSULT

  1. Connect 12V battery cable to negative terminal.

  2. Power switch OFF to ON without depressing the brake pedal.

  3. Power switch OFF and disconnect CONSULT from data link connector.

  4. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  5. Power switch OFF to ON without depressing the brake pedal.

  6. Erase self-diagnosis result for “BRAKE”.

  7. Power switch OFF and disconnect CONSULT from data link connector.

  8. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  9. Power switch OFF to ON without depressing the brake pedal.

  10. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FE-29" detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK CONNECTOR TERMINALS

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector, then check for malfunctions of terminals and connections.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

With CONSULT

  1. Connect electrically-driven intelligent brake unit harness connector.

  2. Connect 12V battery cable to negative terminal.

  3. Power switch OFF to ON without depressing the brake pedal.

  4. Power switch OFF and disconnect CONSULT from data link connector.

  5. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  6. Power switch OFF to ON without depressing the brake pedal.

  7. Erase self-diagnosis result for “BRAKE”.

  8. Power switch OFF and disconnect CONSULT from data link connector.

  9. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  10. Power switch OFF to ON without depressing the brake pedal.

  11. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FE-29" detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect electrically-driven intelligent brake unit harness connector.

  5. Check the electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link. GO TO 6.

PERFORM SELF-DIAGNOSIS (3)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FE-29" detected?

YES>>

GO TO 7.

NO>>

INSPECTION END

CHECK DATA MONITOR

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Select “BRAKE”, “Data monitor” according this order.

  3. Check "Temperature 1" and "Temperature 2". Refer to Values On The Diagnosis Tool.

Is "Temperature " -50℃ (-58℉) or less, or 125℃ (257℉) or more?

YES>>

GO TO 8.

NO>>

GO TO 9.

CHECK MOTOR ROOM

Check for any locations of abnormal heating around the electrically-driven intelligent brake unit.

Are there any heated locations?

YES>>

Perform diagnosis of the heated locations, and wait for the temperature to fall. GO TO 9.

NO>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

PERFORM SELF-DIAGNOSIS (4)

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch OFF to ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch OFF to ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC "C18FE-29" detected?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

INSPECTION END

U1fa1-86 Can Comm Circuit Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
U1FA1 86 CAN communication error (ADAS control unit) 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in ADAS control unit 2 system.
Diagnosis delay time 1 second or less
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in ADAS control unit 2 signal.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • ADAS control unit 2

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “U1FA1-86" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

U2140-87 Can Comm Circuit Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
U2140 87 Controller area network communication error (Engine control module) 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not receiving from VCM.
Diagnosis delay time 2 seconds or more
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not transmitting to VCM.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • VCM

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “U2140-87" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

U2143-87 Can Comm Circuit Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
U2143 87 Controller area network communication error (Nissan Ariya Vehicle control module/Hybrid control module) 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not receiving from VCM.
Diagnosis delay time 2 seconds or more
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not transmitting to VCM.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • VCM

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “U2143-87" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

U2148-87 Can Comm Circuit Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
U2148 87 CAN communication error brake control unit 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not receiving from ABS actuator and electric unit (control unit).
Diagnosis delay time 2 seconds or more
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not transmitting to S actuator and electric unit (control unit).
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • ABS actuator and electric unit (control unit)

  • CAN communication line

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “U2148-87" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

U214f-87 Can Comm Circuit Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
U214F 87 CAN communication error (BCM) 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not receiving from BCM.
Diagnosis delay time 2 seconds or more
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not transmitting to BCM.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • BCM

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “U214F-87" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

U2240-87 Can Comm Circuit Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
U2240 87 Controller area network communication error (Engine control module) 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not receiving from VCM.
Diagnosis delay time 2 seconds or more
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not transmitting to VCM.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • VCM

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “U2240-87" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

U2243-87 Can Comm Circuit Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
U2243 87 Controller area network communication error (Nissan Ariya Vehicle control module/Hybrid control module) 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not receiving from VCM.
Diagnosis delay time 2 seconds or more
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not transmitting to VCM.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • VCM

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “U2243-87" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

U2248-87 Can Comm Circuit Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
U2248 87 CAN communication error brake control unit 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not receiving from ABS actuator and electric unit (control unit).
Diagnosis delay time 2 seconds or more
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not transmitting to ABS actuator and electric unit (control unit).
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • ABS actuator and electric unit (control unit)

  • CAN communication line

FAIL-SAFE

The following functions are suspended.

  • Cooperative regenerative brake function

  • e-Step function

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “U2248-87" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

U224f-87 Can Comm Circuit Nissan Ariya 1st generation

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
U224F 87 CAN communication error (BCM) 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not receiving from BCM.
Diagnosis delay time 2 seconds or more
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not transmitting to BCM.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • BCM

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “U224F-87" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

U2252-87 Can Comm Circuit Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
U2252 87 CAN communication error advanced driver assistant systems control unit 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not receiving from ADAS control unit 2.
Diagnosis delay time 2 seconds or more
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not transmitting to ADAS control unit 2.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • ADAS control unit 2

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “U2252-87" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

U225b-87 Can Comm Circuit Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
U225B 87 CAN communication error (IPDM E/R) 1 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not receiving from IPDM E/R.
Diagnosis delay time 2 seconds or more
2 Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold When not transmitting to IPDM E/R.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • IPDM E/R

  • CAN communication line

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING

If “Confirmation Procedure” has been previously conducted, always power switch OFF, get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

>>

GO TO 2.

CHECK DTC DETECTION

With CONSULT

  1. Power switch OFF to ON without depressing the brake pedal.

  2. Power switch OFF and disconnect CONSULT from data link connector.

  3. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  4. Power switch ON without depressing the brake pedal.

  5. Erase self-diagnosis result for “BRAKE”.

  6. Power switch OFF and disconnect CONSULT from data link connector.

  7. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  8. Power switch ON without depressing the brake pedal.

  9. Perform self-diagnosis for “BRAKE”.

Is DTC “U225B-87" detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

Refer to Trouble Diagnosis Flow Chart.

Power Supply and Ground Circuit Nissan Ariya SUV

Diagnosis Procedure

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SWITCH ON POWER SUPPLY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect the electrically-driven intelligent brake unit harness connector.

  5. Connect 12V battery cable to negative terminal.

  6. Check the voltage between the electrically-driven intelligent brake unit harness connector and ground.

    +—Voltage
    Electrically-driven intelligent brake unit
    ConnectorTerminal

    B63*1

    B64*2
    20 Ground Approx. 0 V

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Power switch ON without depressing the brake pedal.

  8. Check the voltage between the electrically-driven intelligent brake unit harness connector and ground.

    +—Voltage
    Electrically-driven intelligent brake unit
    ConnectorTerminal

    B63*1

    B64*2
    20 Ground 10 − 16 V

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SWITCH ON POWER SUPPLY CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 10A fuse (#51).

  5. Disconnect fuse block (F/B) harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit harness connector and fuse block (J/B) harness connector.

    Electrically-driven intelligent brake unitFuse block (F/B)Continuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2
    20 E57 75 Existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  7. Check the continuity between electrically-driven intelligent brake unit harness connector and ground.

    Electrically-driven intelligent brake unit—Continuity
    ConnectorTerminal

    B63*1

    B64*2
    20 Ground Not existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

Perform trouble diagnosis for power switch ON power supply.

NO>>

Repair / replace harness, connector, or fuse.

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT MOTOR POWER SUPPLY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Connect 12V battery cable to negative terminal.

  3. Check the voltage between the electrically-driven intelligent brake unit harness connector and ground.

    Electrically-driven intelligent brake unitVoltage
    ConnectorTerminal
    +-

    B63*1

    B64*2
    1 9 10 - 16 V

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

  4. Power switch ON without depressing the brake pedal.

  5. Check the voltage between the electrically-driven intelligent brake unit harness connector and ground.

    Electrically-driven intelligent brake unitVoltage
    ConnectorTerminal
    +-

    B63*1

    B64*2
    1 9 10 - 16 V

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT MOTOR POWER SUPPLY CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 50A fusible link (#M).

  5. Check the continuity and for short circuit between harness connector terminal 1 of electrically-driven intelligent brake unit and 50A fusible link (#M).

Is the inspection result normal?

YES>>

Perform trouble diagnosis for 12V battery power supply.

NO>>

Repair / replace harness, connector, fuse, or fusible link.

CHECK BRAKE POWER SUPPLY BACKUP UNIT 12V BATTERY POWER SUPPLY

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect brake power supply backup unit harness connector.

  5. Connect 12V battery cable to negative terminal.

  6. Check the voltage between brake power supply backup unit harness connector and ground.

    +—Voltage
    Brake power supply backup unit
    ConnectorTerminal
    B94 6 Ground 10 − 16 V
  7. Power switch ON without depressing the brake pedal.

  8. Check the voltage between brake power supply backup unit harness connector and ground.

    +—Voltage
    Brake power supply backup unit
    ConnectorTerminal
    B94 6 Ground 10 − 16 V

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 6.

CHECK BRAKE POWER SUPPLY BACKUP UNIT 12V BATTERY POWER SUPPLY CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Check the 30A fusible link (#62).

  5. Check the continuity and for short circuit between harness connector terminal 6 of brake power supply backup unit and 30A fusible link (#62).

Is the inspection result normal?

YES>>

Perform trouble diagnosis for 12V battery power supply.

NO>>

Repair / replace harness, connector, or fusible link.

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT GROUND

Check the continuity between electrically-driven intelligent brake unit harness connector and ground.

Electrically-driven intelligent brake unit—Continuity
ConnectorTerminal

B63*1

B64*2
9 Ground Existed

*1: Without ProPILOT Assist 2.0

*2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector.

CHECK BRAKE POWER SUPPLY BACKUP UNIT GROUND

Check the continuity between brake power supply backup unit harness connector and ground.

Brake power supply backup unit—Continuity
ConnectorTerminal
B94 2 Ground Existed

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair / replace harness or connector.

CHECK TERMINAL

  1. Check electrically-driven intelligent brake unit terminals for damage or loose connection with harness connector.

  2. Check fuse block (J/B) terminals for damage or loose connection with harness connector.

  3. Check brake power supply backup unit terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair / replace harness, connector, or terminal.

Warning Buzzer Nissan Ariya: FE0

Diagnosis Procedure

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

Perform the trouble diagnosis for electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

CHECK WARNING BUZZER CIRCUIT

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect the electrically-driven intelligent brake unit harness connector.

  5. Disconnect buzzer harness connector.

  6. Check the continuity between electrically-driven intelligent brake unit and warning buzzer.

    Electrically-driven intelligent brake unitWarning buzzerContinuity
    ConnectorTerminalConnectorTerminal

    B63*1

    B64*2

    11*1

    6*2
    M20 1 Existed

    19*1

    13*2
    1 Not existed

    11*1

    6*2
    2 Not existed

    19*1

    13*2
    2 Existed

    *1: Without ProPILOT Assist 2.0

    *2: With ProPILOT Assist 2.0

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness or connector.

CHECK WARNING BUZZER

Check the warning buzzer. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

Replace the warning buzzer. Refer to WARNING BUZZER : Removal & Installation.

Component Inspection

CHECK WARNING BUZZER

  1. Power switch OFF and disconnect CONSULT from data link connector.

  2. Get out of the Nissan Ariya vehicle, close all doors (other than hood assembly), check that the combination meter is OFF, and wait for 1 minute or more without opening these doors.

  3. Disconnect 12V battery cable from negative terminal.

  4. Disconnect buzzer harness connector.

  5. Apply voltage of 12V between warning buzzer connector terminals 1 and 2.

    ConditionWarning buzzer
    Voltage applied Sound
    Voltage not applied No sound

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace the warning buzzer. Refer to WARNING BUZZER : Removal & Installation.

Brake Warning Lamp Nissan Ariya 2026

Component Function Check

CHECK BRAKE WARNING LAMP FUNCTION (1)

Check that brake warning lamp turns ON for several second after power switch is turned ON.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Refer to Diagnosis Procedure.

CHECK BRAKE WARNING LAMP FUNCTION (2)

Check that brake warning lamp in combination meter turns ON or OFF when brake fluid level switch is operated while brake fluid level in reservoir tank is at the specified level.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Check the brake fluid level switch system. Refer to Component Inspection.

Diagnosis Procedure

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY ANG GROUND CIRCUIT

Perform the trouble diagnosis for electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “BRAKE” and “ABS”.

Is malfunction detected?

YES>>

Check the error-detected system.

  • “BRAKE”: Refer to DTC Index.

  • “ABS”: Refer to DTC Index.

NO>>

GO TO 3.

CHECK THAT BRAKE WARNING LAMP TURNS ON

Check the combination meter. Refer to On Board Diagnosis Function.

Is the inspection result normal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

Repair or replace integrated interface display. Refer to Removal and Installation.

Brake System Warning Lamp Nissan Ariya 1st generation

Component Function Check

CHECK BRAKE SYSTEM WARNING LAMP FUNCTION

Check that brake system warning lamp turns ON for several second after power switch is turned ON.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT POWER SUPPLY AND GROUND CIRCUIT

Perform the trouble diagnosis for electrically-driven intelligent brake unit power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “BRAKE” and “ABS”.

Is a malfunction detected?

YES>>

Check the error-detected system.

  • “BRAKE”: Refer to DTC Index.

  • “ABS”: Refer to DTC Index.

NO>>

GO TO 3.

CHECK BRAKE SYSTEM WARNING LAMP ILLUMINATION

Check the combination meter. Refer to On Board Diagnosis Function.

Is the inspection result normal?

YES>>

Replace the electrically-driven intelligent brake unit. Refer to ELECTRICALLY-DRIVEN INTELLIGENT BRAKE UNIT : Removal & Installation.

NO>>

Repair or replace integrated interface display. Refer to Removal and Installation.