Dtc/circuit Diagnosis

In this manual: Dtc/circuit Diagnosis
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
64steps
~384min
4/5difficulty
Done 0 of 64
  • B2ccf-04 Passenger Door Mirror Control Module
  • B2ccf-95 Passenger Door Mirror Control Module
  • Power Supply and Ground Circuit
  • Intelligent Rear View Mirror
  • Power Window Main Switch
  • Passenger Door Mirror Control Module
  • Mirror Motor
  • Lin Communication Circuit

B2ccf-04 Passenger Door Mirror Control Module Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B2CCF-04 Passenger door mirror control module Diagnosis condition Power switch is ON or OFF (auto ACC status).
Signal (terminal) LIN communication (door mirror) signal
Threshold BCM detects communication error with passenger door mirror control module
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Passenger door mirror control module

  • LIN communication line

  • BCM

FAIL SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Power switch ON.

  2. Select “Self Diagnostic Result” mode of “BCM” using CONSULT.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK LIN COMMUNICATION SIGNAL

  1. Power switch ON.

  2. Check signal between passenger door mirror control module harness connector and ground using an oscilloscope.

    (+)(−)

    Signal

    (Reference value)
    Passenger door mirror control module
    ConnectorTerminal
    D8 7 Ground

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK PASSENGER DOOR MIRROR CONTROL MODULE CIRCUIT

  1. Power switch OFF.

  2. Disconnect passenger door mirror control module connector and BCM connector.

  3. Check continuity between passenger door mirror control module harness connector and BCM harness connector.

    Passenger door mirror control moduleBCMContinuity
    ConnectorTerminalConnectorTerminal
    D8 7 M8 24 Existed
  4. Check continuity between passenger door mirror control module harness connector and ground.

    Passenger door mirror control module—Continuity
    ConnectorTerminal
    D8 7 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness.

REPLACE PASSENGER DOOR MIRROR CONTROL MODULE

Replace passenger door mirror control module. Refer to Removal & Installation.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 4.

REPLACE BCM

Replace BCM. Refer to Removal and Installation.

>>

INSPECTION END

B2ccf-95 Passenger Door Mirror Control Module Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B2CCF-95 Passenger door mirror control module Diagnosis condition Power switch is ON or OFF (auto ACC status).
Signal (terminal) LIN communication signal
Threshold BCM cannot LIN communication with passenger door mirror control module
Diagnosis delay time 2 second or less

POSSIBLE CAUSE

  • LIN communication line

  • Passenger door mirror control module

  • BCM

FAIL SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

When DTC "B2CCF-95" is displayed together with DTC "B2CCF-04", perform the diagnosis of DTC "B2CCF-04" first.

Is applicable DTC detected?

YES>>

Refer to DTC Description.

NO>>

GO TO 2.

CHECK SELF-DIAG RESULT

With CONSULT

  1. Power switch ON.

  2. Perform “Self Diagnostic Result” mode of “BCM” using CONSULT.

Is DTC detected?

YES-1>>

CRNT: Refer to Diagnosis Procedure.

YES-2>>

PAST: GO TO 3.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

CHECK OPERATION

Check that door mirror (passenger side) operate properly.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK DTC PRIORITY

When DTC "B2CCF-95" is displayed together with DTC "B2CCF-04", perform the diagnosis of DTC "B2CCF-04" first.

Is applicable DTC detected?

YES>>

Refer to DTC Description.

NO>>

GO TO 2.

CHECK PASSENGER DOOR MIRROR CONTROL MODULE POWER SUPPLY AND GROUND CIRCUIT

Check passenger door mirror control module power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace the malfunctioning parts.

CHECK LIN COMMUNICATION CIRCUIT

Check LIN communication circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace passenger door mirror control module. Refer to Removal & Installation.

NO>>

Repair or replace the malfunctioning parts.

Intelligent Rear View Mirror Nissan Ariya SUV

Diagnosis Procedure

CHECK INTELLIGENT REAR VIEW MIRROR CIRCUIT

  1. Power switch OFF.

  2. Replace between intelligent rear view mirror harness connector and intelligent rear view mirror camera harness connector.

  3. Power switch ON.

  4. Turn power supply lever of intelligent rear view mirror lower part to ON and check whether the intelligent rear view mirror camera image is reflected to intelligent rear view mirror in built LCD monitor.

Is the inspection result normal?

YES>>

Replace between intelligent rear view mirror harness connector and intelligent rear view mirror camera harness connector.

NO>>

GO TO 2.

CHECK INTELLIGENT REAR VIEW MIRROR CAMERA

  1. Power switch OFF.

  2. Replace intelligent rear view mirror camera. Refer to Removal & Installation.

  3. Power switch ON.

  4. Turn power supply lever of intelligent rear view mirror lower part to ON and check whether the intelligent rear view mirror camera image is reflected to intelligent rear view mirror in built LCD monitor.

Is the inspection result normal?

YES>>

Replace intelligent rear view mirror camera. Refer to Removal & Installation.

NO>>

GO TO 3.

CHECK INTELLIGENT REAR VIEW MIRROR

  1. Power switch OFF.

  2. Replace intelligent rear view mirror. Refer to Removal & Installation.

  3. Power switch ON.

  4. Turn power supply lever of intelligent rear view mirror lower part to ON and check whether the intelligent rear view mirror camera image is reflected to intelligent rear view mirror in built LCD monitor.

Is the inspection result normal?

YES>>

Replace intelligent rear view mirror. Refer to Removal & Installation.

NO>>

Check intermittent incident. Refer to Intermittent Incident..

Power Window Main Switch Nissan Ariya first Gen

Diagnosis Procedure

CHECK POWER WINDOW MAIN SWITCH CIRCUIT

  1. Power switch OFF.

  2. Disconnect power window main switch connector and door mirror (driver side) connector.

  3. Check continuity between power window main switch harness connector and door mirror (driver side) harness connector.

    Power window main switchDoor mirror (driver side)Continuity
    ConnectorTerminalConnectorTerminal
    D63 10 D64 7 Existed
    2 15
    8 14
    14 16
    21 6
    7 13
    6 8
    17 5
    18 4
  4. Check continuity between power window main switch harness connector and ground.

    Power window main switch—Continuity
    ConnectorTerminal
    D63 10 Ground Not existed
    2
    8
    14
    21
    7
    6
    17
    18

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace harness.

REPLACE DOOR MIRROR (DRIVER SIDE)

Replace door mirror (driver side). Refer to Removal & Installation.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 3.

REPLACE POWER WINDOW MAIN SWITCH

Replace power window main switch. Refer to Removal and Installation.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 4.

REPLACE BCM

Replace BCM. Refer to Removal and Installation.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 5.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

>>

INSPECTION END

Passenger Door Mirror Control Module Nissan Ariya first Gen

Diagnosis Procedure

CHECK FUSE

  1. Power switch OFF.

  2. Check that the following fuse is not blown (open).

Fuse No.Capacity
#48 5A

Is the fuse blown (open) ?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK PASSENGER DOOR MIRROR CONTROL MODULE POWER SUPPLY

  1. Disconnect passenger door mirror control module connector.

  2. Power switch ON.

  3. Check voltage between passenger door mirror control module harness connector and ground.

    (+)(−)

    Voltage (V)

    (Approx.)
    Passenger door mirror control module
    ConnectorTerminal
    D8 4 Ground 9 – 16 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness and check fuse.

CHECK LIN COMMUNICATION SIGNAL

  1. Power switch OFF.

  2. Connect passenger door mirror control module connector.

  3. Power switch ON.

  4. Check signal between passenger door mirror control module harness connector and ground using an oscilloscope.
    (+)(−)

    Signal

    (Reference value)
    Passenger door mirror control module
    ConnectorTerminal
    D8 7 Ground

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

CHECK PASSENGER DOOR MIRROR CONTROL MODULE CIRCUIT

  1. Power switch OFF.

  2. Disconnect passenger door mirror control module connector and BCM connector.

  3. Check continuity between passenger door mirror control module harness connector and BCM harness connector.

    Passenger door mirror control moduleBCMContinuity
    ConnectorTerminalConnectorTerminal
    D48 7 M8 24 Existed
  4. Check continuity between passenger door mirror control module harness connector and ground.

    Passenger door mirror control module—Continuity
    ConnectorTerminal
    D48 7 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness.

CHECK PASSENGER DOOR MIRROR CONTROL MODULE CIRCUIT

  1. Power switch OFF.

  2. Disconnect passenger door mirror control module and door mirror (passenger side) connector.

  3. Check continuity between passenger door mirror control module harness connector and door mirror (passenger side) harness connector.

    Passenger door mirror control moduleDoor mirror (passenger side)Continuity
    ConnectorTerminalConnectorTerminal
    D8 11 D24 7 Existed
    6 15
    1 14
    5 16
    10 6
    2 13
    3 8
    9 5
    8 4
  4. Check continuity between passenger door mirror control module harness connector and ground.

    Passenger door mirror control module—Continuity
    ConnectorTerminal
    D8 11 Ground Not existed
    6
    1
    5
    10
    2
    3
    9
    8

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

CHECK PASSENGER DOOR MIRROR CONTROL MODULE GROUND CIRCUIT

Check continuity between passenger door mirror control module harness connector and ground.

Passenger door mirror control module—Continuity
ConnectorTerminal
D8 12 Ground Existed

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace harness.

REPLACE DOOR MIRROR (PASSENGER SIDE)

Replace door mirror (passenger side). Refer to Disassembly & Assembly.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 8.

REPLACE PASSENGER DOOR MIRROR CONTROL MODULE

Replace passenger door mirror control module. Refer to Removal & Installation.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 9.

REPLACE BCM

Replace BCM. Refer to Removal and Installation.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 10.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

>>

INSPECTION END

Mirror Motor Nissan Ariya 2026

Component Function Check

CHECK DOOR MIRROR RETRACT FUNCTION

  1. Power switch ON.

  2. Operate changeover switch, and then operate mirror switch. Check that door mirror operates normally.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK POWER WINDOW MAIN SWITCH OUTPUT SIGNAL

  1. Power switch ON.

  2. Check voltage between power window main switch harness connector and ground.

    (+)(–)Condition

    Voltage

    (Approx.)
    Power window main switch
    ConnectorTerminalChangeover switchMirror switch
    D63 21 Ground LEFT DOWN or RIGHT 9 ‐ 16 V
    Other than above 0 ‐ 1 V
    10 LEFT 9 ‐ 16 V
    Other than above 0 ‐ 1 V
    6 UP 9 ‐ 16 V
    Other than above 0 ‐ 1 V
    7 RIGHT DOWN or RIGHT 9 ‐ 16 V
    Other than above 0 ‐ 1 V
    9 LEFT 9 ‐ 16 V
    Other than above 0 ‐ 1 V
    8 UP 9 ‐ 16 V
    Other than above 0 ‐ 1 V

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 2.

CHECK MIRROR MOTOR AND FOLDING MOTOR CIRCUIT

  1. Power switch OFF.

  2. Disconnect door mirror and power window main switch connector.

  3. Check continuity between door mirror harness connector and power window main switch harness connector.

    Door mirrorPower window main switchContinuity
    ConnectorTerminalConnectorTerminal
    Driver side D64 6 D63 21 Existed
    7 10
    8 6
    5 17
    4 18
    Passenger side D24 6 7
    7 9
    8 8
    5 20
    4 19
  4. Check continuity between power window main switch harness connector and ground.

    Power window main switch—Continuity
    ConnectorTerminal
    D63 21 Ground Not existed
    10
    6
    17
    18
    7
    9
    8
    20
    19

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness or connector.

REPLACE POWER WINDOW MAIN SWITCH

Replace power window main switch. Refer to Removal and Installation.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 4.

REPLACE DOOR MIRROR

Replace door mirror. Refer to Removal & Installation.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Check intermittent incident. Refer to Intermittent Incident.

Lin Communication Circuit Nissan Ariya 1st generation

Diagnosis Procedure

CHECK BCM OUTPUT SIGNAL

  1. Power switch ON.

  2. Check signal between BCM harness connector and ground using an oscilloscope.

    (+)(−)Signal
    BCM
    ConnectorTerminal
    M8 24 Ground

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK LIN COMMUNICATION CIRCUIT

  1. Power switch OFF, and then wait for 1 minutes with driver door open.

  2. Disconnect following connectors.

    • BCM

    • Power window main switch

    • Front power window motor (driver side)

    • Front power window motor (passenger side)

    • Rear power window motor RH

    • Rear power window motor LH

    • Sunroof motor assembly

    • Sunshade motor assembly

    • Passenger door mirror control module

  3. Check continuity between BCM harness connector and ground.

    BCM—Continuity
    ConnectorTerminal
    M8 24 Ground Not existed

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK LIN COMMUNICATION SIGNAL

  1. Power switch OFF, and then wait for 1 minutes with driver door open.

  2. Disconnect following connectors.

    • Power window main switch

    • Front power window motor (driver side)

    • Front power window motor (passenger side)

    • Rear power window motor RH

    • Rear power window motor LH

    • Sunroof motor assembly

    • Sunshade motor assembly

    • Passenger door mirror control module

  3. Power switch ON.

  4. Check signal between passenger door mirror control module and ground using an oscilloscope.

    (+)(−)Signal
    Passenger door mirror control module
    ConnectorTerminal
    D8 7 Ground

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 4.

CHECK LIN COMMUNICATION CIRCUIT

  1. Power switch OFF.

  2. Disconnect BCM connector.

  3. Check continuity between BCM harness connector and passenger door mirror control module harness connector.

    BCMpassenger door mirror control moduleContinuity
    ConnectorTerminalConnectorTerminal
    M8 24 D8 7 Existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace harness.