Front Door
Exploded View

| Front door panel | Grommet | Front door striker | |||
| TORX bolt | Front door check link | Front door hinge (lower) | |||
| Front door hinge (upper) | Front door weather-strip | Front door parting seal lower | |||
| Front door parting seal front | |||||
| : Clip | |||||
| : Always replace after every disassembly. | |||||
| : N·m (kg-m, in-lb) | |||||
| : N·m (kg-m, ft-lb) | |||||
| : Body grease | |||||
- Front Door Assembly
- Front Door Striker
- Front Door Hinge
- Front Door Check Link
- Front Door Weather-Strip
- Front Door Parting Seal
Front Door Assembly Nissan Ariya SUV
Removal & Installation
REMOVAL
Disconnect front door harness connector.Disengage connector pin
, and then pull lock release lever
according to numerical order 1→2 indicated by arrows as shown in figure.

| : Nissan Ariya Vehicle front |
Remove front door check link mounting bolt of Nissan Ariya vehicle body side.
Support front door assembly with a proper material to prevent it from falling.
Remove front door hinge mounting nuts, and then remove front door assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
Inspection
Open and close the door. Check that door hinge and check link rotation portion moves smoothly.
Check door hinge rotating part for poor lubrication. Apply body grease if necessary.

| : Body grease |
Check door check link rotating part for poor lubrication. Apply body grease if necessary.

| : Body grease |
Adjustment
FITTING ADJUSTMENT
Fitting Adjustment Standard Dimension

| Front fender assembly | Front door panel | Rear door panel | |||
| Front door sash molding | Body side outer | Front door hinge | |||
| Front door striker | TORX bolt | ||||
| : Always replace after every disassembly. | |||||
| : N·m (kg-m, ft-lb) | |||||
| : Body grease | |||||
Unit: mm [in]
| Portion | Standard | |||
|---|---|---|---|---|
| Front door panel – Front fender assembly | F | Clearance | 2.8 – 4.8 [0.110 – 0.189] |
|
| G | Surface height | (−1.0) – (+1.0) [(−0.039) – (+0.039)] |
||
| Front door panel – Rear door panel | H | Clearance | 2.8 – 4.8 [0.110 – 0.189] |
|
| I | Surface height | (−0.5) – (+1.0) [(−0.020) – (+0.039)] |
||
| Front door sash molding – Body side outer | J | Clearance | 4.5 – 7.5 [0.177 – 0.295] |
|
| K | Surface height | (−1.4) – (+1.6) [(−0.055) – (+0.063)] |
||
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures shown below.
Fitting Adjustment Procedure
Remove front door panel. Refer to Removal & Installation.
Remove front fender assembly. Refer to Removal & Installation.
Loosen front door hinge mounting bolts.
Temporary install front door panel and front fender assembly, and then adjust the clearance of front door according to the fitting adjustment standard dimension by moving front door panel.
Remove temporary install parts, and then tighten front door hinge mounting bolts to the specified torque.
Install front fender assembly. Refer to Removal & Installation.
Install front door panel, and then loosen front door hinge mounting nuts. Refer to Removal & Installation.
Adjust the surface height of front door according to the fitting adjustment standard dimension by moving front door panel.
Tighten front door hinge mounting nuts to the specified torque.
DOOR STRIKER ADJUSTMENT
Adjust front door striker so that it becomes parallel with door lock insertion direction.
Front Door Striker Nissan Ariya: FE0
Removal & Installation
REMOVAL
Remove TORX bolts, and then remove front door striker.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
Front Door Hinge Nissan Ariya
Removal & Installation
REMOVAL
Remove front door assembly. Refer to Removal & Installation.
Remove front fender assembly. Refer to Removal & Installation.
Remove front door hinge mounting bolts, and then remove front door hinge.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
Front Door Check Link Nissan Ariya 2026
Removal & Installation
REMOVAL
Fully close front door glass.
Remove front door finisher. Refer to Removal & Installation.
Remove front door sealing screen. Refer to Removal & Installation.
Remove front door check link mounting bolt of Nissan Ariya vehicle body side.
Remove front door check link mounting bolts of front door panel, and then take front door check link out from the hole of front door panel.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
Front Door Weather-Strip Nissan Ariya: FE0
Removal & Installation
REMOVAL
Apply protective tape (A) to front door panel
around front door weather-strip
fixing clips for preventing damage.

Disengage fixing clips on the reverse side of front door weather-strip using a remover tool (A).

| : Clip |
Remove front door check link mounting bolt of Nissan Ariya vehicle body side.
Remove front door weather-strip from front door panel.
INSTALLATION
Install in the reverse order of removal.
Front Door Parting Seal Nissan Ariya: FE0
Removal & Installation
REMOVAL
Front door parting seal front
Remove front door panel. Refer to Removal & Installation.
Remove front door parting seal lower front side fixing clip
.

Remove front door parting seal front fixing clips
, and then remove front door parting seal front.

Front door parting seal lower
Remove front door parting seal lower fixing clips
, and then remove front door parting seal lower.

INSTALLATION
Install in the reverse order of removal.