Basic Inspection
- Diagnosis and Repair Work Flow
- Additional Service When Replacing Intelligent Key Unit
- Additional Service When Replacing Automatic Back Door Control Unit
- Configration (intelligent Key Unit)
- Calibration of Automatic Back Door Position Information
Diagnosis and Repair Work Flow Nissan Ariya first Gen
Work Flow
OVERALL SEQUENCE

DETAILED FLOW
GET INFORMATION FOR SYMPTOM
Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurs).
Check operation condition of the function that is malfunctioning.
GO TO 2.
CHECK DTC
Check DTC.
Perform the following procedure if DTC is detected.
Record DTC and freeze frame data (print them out using CONSULT).
Erase DTC.
Study the relationship between the cause detected by DTC and the symptom described by the customer.
Are any symptoms described or any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.
CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Also study the normal operation and fail-safe related to the symptom.
Verify relation between the symptom and the condition when the symptom is detected.
>>GO TO 5.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.
>>GO TO 6.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected again. At this time, always connect CONSULT to the Nissan Ariya vehicle, and check diagnostic results in real time.
If two or more DTCs are detected, refer to DTC Inspection Priority Chart (Intelligent Key unit), DTC Inspection Priority Chart (automatic back door control unit) or DTC Inspection Priority Chart (BCM), and determine trouble diagnosis order.
Is DTC detected?
YES>>GO TO 7.
NO>>Refer to Intermittent Incident.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step 4, and determine the trouble diagnosis order based on possible causes and symptom.
Is the symptom described?
YES>>GO TO 7.
NO>>Monitor input data from related sensors or check voltage of related module terminals using CONSULT.
DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?
YES>>GO TO 8.
NO>>Check according to Intermittent Incident.
REPAIR OR REPLACE THE MALFUNCTIONING PART
Repair or replace the malfunctioning part.
Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replacement.
Check for DTC. If DTC is displayed, erase it.
GO TO 9.
FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the malfunction is completely repaired.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the symptom is not detected.
Is DTC detected and does symptom remain?
YES-1>>DTC is detected: GO TO 7.
YES-2>>Symptom remains: GO TO 4.
NO>>Before returning the Nissan Ariya vehicle to the customer, always erase DTC.
Additional Service When Replacing Intelligent Key Unit Nissan Ariya SUV
Description
Perform the following operations when replacing Intelligent Key unit. For details, refer to Work Procedure.
AFTER REPLACEMENT
Writing Nissan Ariya vehicle specification
Register Intelligent Keys
Work Procedure
REPLACE INTELLIGENT KEY UNIT
Replace Intelligent Key unit. Refer to Removal and Installation.
>>GO TO 2.
WRITING Nissan Ariya Vehicle SPECIFICATION
CONSULT Configuration
Perform configuration. Refer to Description.
>>GO TO 3.
REGISTER INTELLIGENT KEYS
For initialization and registration of Intelligent Key: Refer to CONSULT Immobilizer mode and follow the on-screen instructions.
>>WORK END
Additional Service When Replacing Automatic Back Door Control Unit Nissan Ariya
Description
When replacing automatic back door control unit necessary to perform initial setting to operate automatic back door system normally. Refer to Work Procedure.
Work Procedure
STEP 1
Select “AUTOMATIC BACK DOOR” using CONSULT.
Select “Reset auto back door status” of “Work support” mode.
Touch “Start” to erase automatic back door position information.
GO TO 2.
STEP 2
Fully close the back door manually.
>>GO TO 3.
STEP 3
Operate back door opener switch and perform automatic back door open operation.
>>GO TO 4.
STEP 4
The back door fully opens.
Check that automatic back door warning buzzer sounds normally.
Does automatic back door warning buzzer sound normally?
YES>>GO TO 5.
NO>>GO TO 2.
STEP 5
Fully close the back door.
>>WORK END
Configration (intelligent Key Unit) Nissan Ariya SUV
Description
Vehicle specification needs to be written with CONSULT because it is not written after replacing the Intelligent Key unit.
CONSULT connects to network and then it downloads the configuration data from the server. Then CONSULT writes the Nissan Ariya vehicle specification to the Intelligent Key unit.
Refer to Work Procedure.
Work Procedure
WRITING VEHICLE SPECIFICATION
With CONSULT
Perform writing Nissan Ariya vehicle specification to Intelligent Key unit according to "Replace ECU" in CONSULT Operation Manual.
>>WORK END
Calibration of Automatic Back Door Position Information Nissan Ariya SUV
Description
When the following work is performed, it is necessary to perform initial setting of automatic back door position information to operate automatic back door system. Refer to Work Procedure.
After removing and installing, or replacing automatic back door control unit
After removing and installing, or replacing back door assembly
After removing and installing, or replacing spindle unit
Work Procedure
STEP 1
Select “AUTOMATIC BACK DOOR” using CONSULT.
Select “Reset auto back door status” of “Work support” mode.
Touch “Start” to erase automatic back door position information.
GO TO 2.
STEP 2
Fully close the back door manually.
>>GO TO 3.
STEP 3
Operate back door opener switch and perform automatic open operation.
>>GO TO 4.
STEP 4
The back door fully opens.
Check that automatic back door warning buzzer sounds normally.
Does automatic back door warning buzzer sound normally?
YES>>GO TO 5.
NO>>GO TO 2.
STEP 5
Fully close the back door.
>>WORK END