Disassembly and Assembly

In this manual: Disassembly and Assembly
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
8steps
~48min
5/5difficulty
Done 0 of 8
  • Li-Ion Battery Heater. 2wd
  • Battery Pack Upper Case
  • Battery Pack Lower Case. 2wd
  • Service Plug Bracket
  • Li-Ion Battery Controller
  • Busbar. 2wd
  • Battery Junction Box and Battery Harness
  • Front Module Stack
  • Rear Module Stack

Li-Ion Battery Heater. 2wd Nissan Ariya 2026

Exploded View

Li-ion battery cooler tube (front right) Li-ion battery cooler tube (front left) Li-ion battery
Li-ion battery cooler tube 1 (right) Li-ion battery cooler tube 2 (right) Li-ion battery cooler tube 3 (right)
Li-ion battery cooler tube 4 (right) Li-ion battery cooler tube 5 (left) Li-ion battery cooler tube 6 (left)
Li-ion battery cooler tube 7 (left) Li-ion battery cooler tube 8 (left) Li-ion battery cooler tube (rear right)
Li-ion battery cooler tube (rear left) Li-ion battery cooler tube (rear right) upper Clamp
Li-ion battery cooler hose (right) Battery heater Li-ion battery cooler hose (left)
Li-ion battery cooler tube (rear left) upper Battery heater bracket 1 Battery heater bracket 3
Battery heater bracket 2 Battery heater bracket 4
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)

Disassembly & Assembly

DANGER:

Because hybrid vehicles and electric vehicles contain a high voltage battery, there is a risk of electric shock, electric leakage, or similar accidents if the Nissan Ariya vehicle is handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

DISASSEMBLY

LI-ION BATTERY COOLER TUBE (FRONT)

If necessary, remove Li-ion battery cooler tubes (front right and front left).

  1. Push claws of connector on Li-ion battery cooler tubes (front right and front left) and remove from the Li-ion battery until all connectors are half-locked.

  2. Remove mounting bolts of Li-ion battery cooler tubes (front right and front left ).

  3. Remove Li-ion battery cooler tubes (front right and front left) from Li-ion battery.

LI-ION BATTERY COOLER TUBE (REAR)

Remove Li-ion battery. Refer to Removal & Installation.

If necessary, remove Li-ion battery cooler tubes (rear right and rear left).

  1. Remove Li-ion battery cooler tubes (rear right and rear left) from Li-ion battery cooler tube (rear right and rear left) uppers, respectively.

  2. Push claws of connector on Li-ion battery cooler tubes (rear right and rear left) and remove from Li-ion battery until all connectors are half-locked.

  3. Remove Li-ion battery cooler tubes (rear right and rear left) from Li-ion battery.

LI-ION BATTERY COOLER 1-4 (RIGHT), LI-ION BATTERY COOLER 5-8 (LEFT)

Remove Li-ion battery. Refer to Removal & Installation.

Remove Li-ion battery cooler tube 1-4 (right) and Li-ion battery cooler tube 5-8 (left).Push claws of connector on Li-ion battery cooler tubes and then remove from the Li-ion battery until all connectors are half-locked.

Left side
Right side
Left bottom
Right bottom

Also remove opposite side cooler tube connectors until all connectors are half-locked. Remove Li-ion battery.

Cooler tubes from Li-ion battery.

BATTERY HEATER

If necessary, remove Li-ion battery. Refer to Removal & Installation.

  1. Remove Li-ion battery. Refer to Removal & Installation.

  2. Remove Li-ion battery cooler tube 1-4 (right) and Li-ion battery cooler tube 5-8 (left).

Remove high voltage harness connector .

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear.

  • Because there is the danger of electric shock, immediately insulate disconnected high voltage connectors and terminals with insulating tape.

Remove harness connector by turning in the direction of arrow.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear.

  • Because there is the danger of electric shock, immediately insulate disconnected high voltage connectors and terminals with insulating tape.

Remove battery heater bracket mounting bolts .

DANGER:
  • To prevent electric shock, wear insulated protective gear.

Remove battery heater sides only of Li-ion battery heater hose {left and right }

:battery heater bracket 4

DANGER:
  • To prevent electric shock, wear insulated protective gear.

Remove battery heater bracket 1 mounting nuts , and then remove battery heater bracket 1 from battery heater bracket 2 .

DANGER:
  • To prevent electric shock, wear insulated protective gear.

Remove harness clamp parts

DANGER:
  • To prevent electric shock, wear insulated protective gear.

Remove mounting bolts of battery heater brackets 2 and 3, and then remove battery heater brackets 2 and 3 from battery heater bracket 4 .

DANGER:
  • To prevent electric shock, wear insulated protective gear.

Remove mounting bolts of battery heater bracket 4, and then remove battery heater bracket 4 from battery heater .

DANGER:
  • To prevent electric shock, wear insulated protective gear.

If necessary, remove Li-ion battery cooler tubes {rear right upper and rear left upper } , and Li-ion battery cooler hoses {right and left }.

DANGER:
  • To prevent electric shock, wear insulated protective gear.

ASSEMBLY

Assemble in the reverse order of disassembly, and pay attention to the following caution.

Battery Pack Upper Case Nissan Ariya 2023

Exploded View

BATTERY PACK UPPER CASE REAR

Retainer (RH) Retainer (FR) Retainer (LH)
Retainer (RR) Service plug retainer Battery pack upper case rear
Insulator cover Seal Resin retainer
Clip Resin retainer Resin retainer
Resin retainer Service plug Battery pack lower case
: Comply with the assembly procedure when tightening. Removal & Installation
: Nissan Ariya Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)

BATTERY PACK UPPER CASE FRONT

Resin retainer Resin retainer Resin retainer
Retainer Retainer Retainer
Battery pack upper case front Seal Seal
Bracket Battery pack lower case
: Comply with the assembly procedure when tightening. Removal & Installation
: Nissan Ariya Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
,,,,,,,: Indicates that the part is connected at points with same symbol in actual Nissan Ariya vehicle.

Heat shield sheet

Battery pack upper case Heat shield sheet Heat shield sheet
Heat shield sheet Heat shield sheet Heat shield sheet
: Nissan Ariya Vehicle front
: Always replace after every disassembly

Removal & Installation

DANGER:

Since hybrid vehicles and electric vehicles contain a high voltage battery, there is the risk of electric shock, electric leakage, or similar accidents if the high voltage component and Nissan Ariya vehicle are handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

ENVIRONMENT FOR LI-ION BATTERY DISASSEMBLY WORK

Must be an indoor environment.

  • The environment must utilize a shutter or other means to shut out the outside environment and prevent rain, snow, dust, or other substances from entering.

  • The environment must not cause the intrusion of sweat during work, or cause condensation to occur due to high temperature or humidity.

Metal powder, grease, and other foreign substances must not enter.

  • The indoor environment must also prevent metal powder, grease, and other foreign substances from entering due to maintenance performed on other Nissan Ariya vehicles and other sources during disassembly work.

  • During disassembly without internal work, temporarily close the battery pack upper case or cover it with an insulating cover.

The floor must be dry.

  • The floor must not be wet as a result of factors such as Nissan Ariya vehicle entry during rain or snow.

Work space

  • The work space must be approximately the size of one entire Nissan Ariya vehicle.

  • Take appropriate countermeasures so that persons other than the operator do not enter the work space, such as by placing signs indicating that disassembly work is in progress.

Standard fire fighting equipment

  • Always place a standard fire fighting equipment in the disassembly work area.

  • Depending on type of fire (Nissan Ariya vehicle or battery) use standard fire fighting equipment (water or extinguisher).

BATTERY PACK UPPER CASE REAR

REMOVAL

Remove tightening bolts of battery heater bracket from battery pack lower case.

Remove Li-ion battery cooler tube from battery pack upper floor assembly. Refer to Disassembly & Assembly.

Remove service plug retainer.

: Battery front

Remove left and right retainers.

Remove left and right resin retainer.

Remove each bolt and for each retainer (FR, RR, LH and RH).

Hold both sides of the battery pack upper case to remove it.

Remove insulator cover.

Remove the seal from battery pack upper floor assembly.

Remove the seal from service plug bracket.

INSTALLATION

Check that heat shield sheet is still stuck back of battery upper case.

  • When the sheet is peeled or battery pack upper case rear is replaced, stick new heat shield sheet according to the following procedure.

Place the battery pack upper case on a pre-cured area so that the outside of the battery pack upper case rear is not damaged Wipe the surface of the battery pack upper case rear where the heat shield sheet are stuck with a dry cloth to remove oil and dust. If the temperature of the work space is 15 ℃ (59 °F)or less, heat the surface of the battery pack upper case rear where heat shield sheet are stuck to 15 - 50 ℃ (59 - 112 °F)with a heat gun or equivalent.
  • For the battery pack upper case rear, warm the surface where the heat shield sheet are stuck for at least 5 minutes so that the entire surface is at least 15 ℃ (59 °F).

  • Remove the release paper from the heat shield sheet, and then heat the side stuck to battery pack upper case rear for at least 1 minute so that its temperature is 15 ℃ (59 °F) or higher.

Stick the heat shield sheet in the following procedure.
  • Stick the heat shield sheet to the battery pack upper case rear as shown in the figure.

    Position mark (Projection)

After sticking the heat shield sheet, press the whole by hands.

Install seal to battery pack upper floor assembly.

Install guide pin [SST: KV99119600 (J-53348)] (A) to the center of battery pack upper floor assembly.

Install insulator cover

Install the seal of service plug bracket.

Hold both sides of the battery pack upper case to install it.

Install each bolt and for each retainer (FR, RR, LH and RH).

Install left and right resin retainer.

: Battery front
: 8.0 N.m (0.82 kg-m, 71 in-lb)

Install service plug retainer.

Install Li-ion battery cooler tube to battery pack upper floor assembly. Refer to Disassembly & Assembly.

Install battery heater bracket to battery pack lower case.

BATTERY PACK UPPER CASE FRONT

REMOVAL

Remove left and right retainers .

Remove left and right resin retainers in the order of 3→2→1

: Battery front

Remove retainer .

: Battery front

Remove bolt .

Remove bolt of backward on the battery pack upper case front.

Hold both sides of the battery pack upper case front to remove it.

Remove seal from battery pack lower case.

INSTALLATION

Check that heat shield sheet is still stuck back of battery upper case front.

  • When the sheet is peeled or battery pack upper case front is replaced, stick new heat shield sheet according to the following procedure.

Place the battery pack upper case front on a pre-cured area so that the outside of the battery pack upper case front is not damaged Wipe the surface of the battery pack upper case front where the heat shield sheet are stuck with a dry cloth to remove oil and dust. If the temperature of the work space is 15 ℃ (59 °F)or less, heat the surface of the battery pack upper case front where heat shield sheet are stuck to 15 - 50 ℃ (59 - 112 °F)with a heat gun or equivalent.
  • For the battery pack upper case front, warm the surface where the heat shield sheet are stuck for at least 5 minutes so that the entire surface is at least 15 ℃ (59 °F).

  • Remove the release paper from the heat shield sheet, and then heat the side stuck to battery pack upper case for at least 1 minute so that its temperature is 15 ℃ (59 °F)or higher.

Stick the heat shield sheet , and to the battery pack upper case front as shown in the figure.

Position mark (Projection)

After sticking the heat shield sheet, press the whole by hands.

Install seal to battery pack lower case.

Hold both sides of battery pack upper case front and install it.

Tighten bolts .

: Battery front
: 11.1 N.m (1.1 kg-m, 8 ft-lb)

Install retainer .

: Battery front
: 8.0 N.m (0.82 kg-m, 71 in-lb)

Tighten bolt.

: Battery front
: 8.0 N.m (0.82 ㎏-m)

Install resin retainers in the order of 1→2→3.

: Battery front
: 8.0 N.m (0.82 kg-m, 71 in-lb)

Install left and right retainers .

Install bolt of backward on the battery pack upper case front.

: 8.0 N.m (0.82 kg-m, 71 in-lb)

Inspection

APPEARANCE CHECK

Check resin retainer for damage.

: Battery front

AIR LEAK INSPECTION

Remove breather and install adapter (A) of air leak tester [SST: KV99112400 (J-53357)].

Install gauge (A) of air leak tester [SST: KV99111400 (-)].

Install service plug. Refer to HOW TO DISCONNECT HIGH VOLTAGE : Precautions.DANGER:

To prevent electric shock, wear insulated protective gear.

Blocks high power connector and Nissan Ariya vehicle communications harness connector with vinyl tape or equivalent for preventing air leakage from connection area.

  • Use wide vinyl tape that is capable of covering all of the high power connector and Nissan Ariya vehicle communications harness connector with one strip.

  • Apply carefully so that no wrinkles in the tape occur.

Block breather with vinyl tape prevent air from leaking.

  • Apply carefully so that no wrinkles in the tape occur.

Perform battery case pressure test according to the following procedure.

Open cock of air leak tester.
Operate the air pump slowly and apply the specified test pressure in the battery pack. If the gauge pressure does not rise, or if the gauge reading fluctuates, check for the location air leakage.

Specified test pressure : 1.6 kPa (0.016 bar, 0.0163 kg/cm2, 0.232 psi)

Close the cock and wait for 1 minute. Check that the air leak tester reading remains at or above the limit value.

Repair limit : 1.4 kPa (0.014 bar, 0.0142 kg/cm2, 0.203 psi)

If the pressure is below the limit value, check for the locations of air leakage.

ELECTRIC EQUIPOTENTIAL TEST

After assembling Li-ion battery pack, remove the battery pack upper case ground bolt , then measure the resistance between the side of battery pack lower case and the seating surface of ground bolt (location of coating peeling) .

Specified value : Less than 0.1 Ω

If the result deviates from the specified value, check the following and repair the malfunction parts.

  • Ground bolt connection condition

  • Corrosion on ground bolt mounting surface

  • Adhesion of paint, oil, dirt, or other substance on ground bolt mounting surface

After assembling Li-ion battery pack, remove the retainer ground bolt , then measure the resistance between the side of battery pack lower case and the seating surface of ground bolt (location of coating peeling) .

Specified value : Less than 0.1 Ω

If the result deviates from the specified value, check the following and repair the malfunction parts.

  • Ground bolt connection condition

  • Corrosion on ground bolt mounting surface

  • Adhesion of paint, oil, dirt, or other substance on ground bolt mounting surface.

After assembling Li-ion battery pack, remove the rear retainer ground bolt , then measure the resistance between the side of battery pack lower case and the seating surface of ground bolt (location of coating peeling) .

: Battery front

Specified value : Less than 0.1 Ω

If the result deviates from the specified value, check the following and repair the malfunction parts.

  • Ground bolt connection condition

  • Corrosion on ground bolt mounting surface

  • Adhesion of paint, oil, dirt, or other substance on ground bolt mounting surface.

Battery Pack Lower Case. 2wd Nissan Ariya 1st generation

Exploded View

Battery pack lower case Battery ventilation valve cover LH Rear box
Seal Battery ventilation valve cover RH Terminal block
Bracket with ept sealer Ept sealer
Battery ventilation valve
: Nissan Ariya Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)

Disassembly & Assembly

DANGER:

Because hybrid vehicles and electric vehicles contain a high voltage battery, there is a risk of electric shock, electric leakage, or similar accidents if the Nissan Ariya vehicle is handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

ENVIRONMENT FOR LI-ION BATTERY DISASSEMBLY WORK

Must be an indoor environment.

  • The environment must utilize a shutter or other means to shut out the outside environment and prevent rain, snow, dust, or other substances from entering.

  • The environment must not cause the intrusion of sweat during work, or cause condensation to occur due to high temperature or humidity.

Metal powder, grease, and other foreign substances must not enter.

  • The indoor environment must also prevent metal powder, grease, and other foreign substances from entering due to maintenance performed on other Nissan Ariya vehicles and other sources during disassembly work.

  • During disassembly without internal work, temporarily close the battery pack upper case or cover it with an insulating cover.

The floor must be dry.

  • The floor must not be wet as a result of factors such as Nissan Ariya vehicle entry during rain or snow.

Work space

  • The work space must be approximately the size of one entire Nissan Ariya vehicle.

  • Take appropriate countermeasures so that persons other than the operator do not enter the work space, such as by placing signs indicating that disassembly work is in progress.

Standard fire fighting equipment

  • Always place a standard fire fighting equipment in the disassembly work area.

  • Depending on type of fire (Nissan Ariya vehicle or battery) use standard fire fighting equipment (water or extinguisher).

REAR BOX

Disassembly

Open bus bar terminal block and remove nut .

Remove connectors , and .

Remove bolts and nuts and the remove rear box .

If necessary, remove clip and the remove Nissan Ariya vehicle communication harness (Battery PTC).

Remove seal from rear box.

ASSEMBLY

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

BATTERY VENTILATION VALVE COVER

Disassembly

Remove right or left battery ventilation valve cover .

Assembly

Install the above right or left ventilation valve cover by aligning with projection of battery pack lower case.

EPT SEALER REPLACEMENT

Check the figure because the procedure differs depending on the location.

to : Stick to bracket
and : Stick to cross member of battery lower case.

Perform parts from to according to the following procedure.Remove the bracket that requires replacement of EPT sealer.

Peel EPT sealer from the bracket. Wipe off any dirt or oil on the surface where EPT sealer is stuck. Cut EPT sealer (Nissan service parts) to the required length.

: 111 mm (4.37 in) × 23 mm (0.91 in)
: 184 mm (7.24 in) × 23 mm (0.91 in)
: 139 mm (5.47 in) × 23 mm (0.91 in)
: 39 mm (1.54 in) × 23 mm (0.91 in)
:58 mm (2.28)×23 (0.91) mm

Stick to the bracket.

: EPT sealer
: Bracket
: 0.5 mm (0.020 in)

Hold EPT seal firmly with the ball of fingers.

Perform parts from and according to the following procedure.

Peel EPT sealer from cross member of battery pack lower case. Wipe off any dirt or oil on the surface of cross member where EPT sealer is stuck. Cut EPT sealer (Nissan service parts) to the required length.

: 150 mm (5.91 in) × 26 mm (1.02 in)
: 100 mm (3.94 in) × 26 mm (1.02 in)

Stick to cross member .

: EPT sealer
: 10 mm (0.39 in)

Service Plug Bracket Nissan Ariya: FE0

Exploded View

REMOVAL

Seal Service plug bracket Breather
: Nissan Ariya Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)

DISASSEMBLY

: TYPE A

: TYPE B

TYPE A

Service plug bracket Service plug switch Engagement detection switch (service plug) harness
Busbar 14 Busbar 13 Busbar 12
: Always replace after every disassembly.
: N·m (kg-m, in-lb)

TYPE B

Service plug bracket Service plug switch Engagement detection switch (service plug) harness
Busbar 14 Busbar 13 Busbar 12
: Always replace after every disassembly.
: N·m (kg-m, in-lb)

Disassembly & Assembly

DANGER:

Because hybrid vehicles and electric vehicles contain a high voltage battery, there is a risk of electric shock, electric leakage, or similar accidents if the Nissan Ariya vehicle is handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

ENVIRONMENT FOR LI-ION BATTERY DISASSEMBLY WORK

Must be an indoor environment.

  • The environment must utilize a shutter or other means to shut out the outside environment and prevent rain, snow, dust, or other substances from entering.

  • The environment must not cause the intrusion of sweat during work, or cause condensation to occur due to high temperature or humidity.

Metal powder, grease, and other foreign substances must not enter.

  • The indoor environment must also prevent metal powder, grease, and other foreign substances from entering due to maintenance performed on other Nissan Ariya vehicles and other sources during disassembly work.

  • During disassembly without internal work, temporarily close the battery pack upper case or cover it with an insulating cover.

The floor must be dry.

  • The floor must not be wet as a result of factors such as Nissan Ariya vehicle entry during rain or snow.

Work space

  • The work space must be approximately the size of one entire Nissan Ariya vehicle.

  • Take appropriate countermeasures so that persons other than the operator do not enter the work space, such as by placing signs indicating that disassembly work is in progress.

Standard fire fighting equipment

  • Always place a standard fire fighting equipment in the disassembly work area.

  • Depending on type of fire (Nissan Ariya vehicle or battery) use standard fire fighting equipment (water or extinguisher).

Disassembly

Remove battery pack upper rear. Refer to Removal & Installation.

Remove the bolt of busbar 12 and .

: Battery front

Remove interlock detecting switch (Service plug) harness connector .

: Battery front

Remove nuts of service plug bracket.

Remove service plug bracket.

Remove seal from service plug bracket.

Remove bolts and remove busbar 12 from busbar 13 and busbar 14.

Remove bolts .

: Service plug

Remove service plug from service bracket .

Remove interlock detecting switch (Service plug) harness , busbar 13 and busbar 14 from service plug .

: Bolts

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

Li-Ion Battery Controller Nissan Ariya 1st generation

Exploded View

Bracket Li-ion battery controller Bracket
Cell controller
: Nissan Ariya Vehicle front
: N·m (kg-m, in-lb)

Removal & Installation

DANGER:

Because hybrid vehicles and electric vehicles contain a high voltage battery, there is a risk of electric shock, electric leakage, or similar accidents if the Nissan Ariya vehicle is handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

ENVIRONMENT FOR LI-ION BATTERY DISASSEMBLY WORK

Must be an indoor environment.

  • The environment must utilize a shutter or other means to shut out the outside environment and prevent rain, snow, dust, or other substances from entering.

  • The environment must not cause the intrusion of sweat during work, or cause condensation to occur due to high temperature or humidity.

Metal powder, grease, and other foreign substances must not enter.

  • The indoor environment must also prevent metal powder, grease, and other foreign substances from entering due to maintenance performed on other Nissan Ariya vehicles and other sources during disassembly work.

  • During disassembly without internal work, temporarily close the battery pack upper case or cover it with an insulating cover.

The floor must be dry.

  • The floor must not be wet as a result of factors such as Nissan Ariya vehicle entry during rain or snow.

Work space

  • The work space must be approximately the size of one entire Nissan Ariya vehicle.

  • Take appropriate countermeasures so that persons other than the operator do not enter the work space, such as by placing signs indicating that disassembly work is in progress.

Standard fire fighting equipment

  • Always place a standard fire fighting equipment in the disassembly work area.

  • Depending on type of fire (Nissan Ariya vehicle or battery) use standard fire fighting equipment (water or extinguisher).

LI-ION BATTERY CONTROLLER

Disassembly

Remove battery pack upper case front. Refer to Removal & Installation.

Remove nut of cable .

: Battery front

Remove the bolt of bracket.

: Battery front

Disconnect the harness connector .

: Battery front

Remove Li-ion battery controller from bracket.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

CELL CONTROLLER (LEFT SIDE)

DISASSEMBLY

Remove battery pack upper case front. Refer to Removal & Installation.

Remove Li-ion battery controller with bracket.

Remove nut on the bracket.

Disconnect the harness connector from cell controller.

Disconnect the cell controller from bracket.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • There two types of cell controller harnesses for high voltage and low voltage. When inserting high voltage harness connector to low voltage system, it may cause fire or damage parts. Carefully avoid mistake when inserting connectors.

CELL CONTROLLER (RIGHT SIDE)

DISASSEMBLY

Remove battery pack upper case front. Refer to Removal & Installation.

Remove bolt on the bracket.

: Battery front

Remove nut on the bracket.

Disconnect the harness connector from cell controller.

Remove cell controller from the bracket.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • There two types of cell controller harnesses for high voltage and low voltage. When inserting high voltage harness connector to low voltage system, it may cause fire or damage parts. Carefully avoid mistake when inserting connectors.

Busbar. 2wd Nissan Ariya 2026

Exploded View

DISASSEMBLY

Busbar 2 Busbar 3 Busbar 4
Busbar 5 Busbar 6 Busbar 7
Busbar 8 Busbar 9 Busbar 10
Busbar 11 Busbar 15 Busbar 16
Busbar 17 Busbar 18 Busbar 19
Busbar 20 Busbar 21 Busbar 22
Busbar 23 Nut cap
: N·m (kg-m, in-lb)

BUSBAR LAYOUT

Busbar 1 Busbar 2 Busbar 3
Busbar 4 Busbar 5 Busbar 6
Busbar 7 Busbar 8 Busbar 9
Busbar 10 Busbar 11 Busbar 12
Busbar 13 Busbar 14 Busbar 15
Busbar 16 Busbar 17 Busbar 18
Busbar 19 Busbar 20 Busbar 21
Busbar 22 Busbar 23 Busbar 24
: Around Service bracket
: Rear module stack 2nd floor

Disassembly & Assembly

DANGER:

Because hybrid vehicles and electric vehicles contain a high voltage battery, there is a risk of electric shock, electric leakage, or similar accidents if the Nissan Ariya vehicle is handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

ENVIRONMENT FOR LI-ION BATTERY DISASSEMBLY WORK

Must be an indoor environment.

  • The environment must utilize a shutter or other means to shut out the outside environment and prevent rain, snow, dust, or other substances from entering.

  • The environment must not cause the intrusion of sweat during work, or cause condensation to occur due to high temperature or humidity.

Metal powder, grease, and other foreign substances must not enter.

  • The indoor environment must also prevent metal powder, grease, and other foreign substances from entering due to maintenance performed on other Nissan Ariya vehicles and other sources during disassembly work.

  • During disassembly without internal work, temporarily close the battery pack upper case or cover it with an insulating cover.

The floor must be dry.

  • The floor must not be wet as a result of factors such as Nissan Ariya vehicle entry during rain or snow.

Work space

  • The work space must be approximately the size of one entire Nissan Ariya vehicle.

  • Take appropriate countermeasures so that persons other than the operator do not enter the work space, such as by placing signs indicating that disassembly work is in progress.

Standard fire fighting equipment

  • Always place a standard fire fighting equipment in the disassembly work area.

  • Depending on type of fire (Nissan Ariya vehicle or battery) use standard fire fighting equipment (water or extinguisher).

Busbar 1 and Busbar 24:

Refer to Disassembly & Assembly.

Busbar 12 to Busbar 14:

Refer to Disassembly & Assembly.

busbar 2 and Busbar 23

DISASSEMBLY

Remove nut cap .

Remove nut and then remove busbar 2 .

Remove busbar 23in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the busbar cover closed until immediately before the installation of busbar.

busbar 3, busbar 4, busbar 21 and busbar 22

DISASSEMBLY

Remove bolts and then remove busbar 3 .

Remove the other busbars in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

busbar 5 and busbar 20

DISASSEMBLY

Remove bracket .

: Bolts

Remove bolts and then remove busbar 5.

Remove busbar 20 in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

busbar 6, busbar 7, busbar 18 and busbar 19

DISASSEMBLY

Remove the battery upper floor assembly. Refer to Disassembly & Assembly.

Remove bolt and nut. And then remove busbar 7.

Remove the bolt . And then remove busbar 6 .

Remove other busbar in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

busbar 8 and busbar 17

DISASSEMBLY

Remove the battery upper floor assembly. Refer to Disassembly & Assembly.

Remove the bolt . And then busbar 8 .

Remove busbar 17 in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

busbar 9

DISASSEMBLY

Remove the battery upper floor assembly. Refer to Disassembly & Assembly.

Remove busbar 8 and busbar 17.

Remove the bracket bolt and . And then move the harness to keep the work space.

Remove the bolt. And then busbar 9.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

busbar 10 and busbar 16

DISASSEMBLY

Remove service plug bracket. Refer to Disassembly & Assembly.

Remove the bolt and nut. And then remove busbar 10.

Remove busbar 16 in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

busbar 11 and busbar 15

DISASSEMBLY

Remove the bolt . And then busbar 11 .

Remove busbar 15 in the same way.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

Battery Junction Box and Battery Harness Nissan Ariya 2023

Exploded View

BATTERY JUNCTION BOX

Nut cap Busbar 1 Busbar 20
Battery junction box Battery pack pressure sensor Bracket
High-voltage harness connector High-voltage harness connector Battery pack water temperature sensor
: N·m (kg-m, in-lb)
,: Indicates that the part is connected at points with same symbol in actual Nissan Ariya vehicle.

BATTERY HARNESS

Nissan Ariya Vehicle communication harness Bracket Nissan Ariya Vehicle communication harness
Cell voltage detection harness Cell voltage detection harness Bracket
Bracket Nissan Ariya Vehicle communication harness (battery PTC) Clip
Busbar terminal block
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
,, : Indicates that the part is connected at points with same symbol in actual Nissan Ariya vehicle.

Disassembly & Assembly

DANGER:

Because hybrid vehicles and electric vehicles contain a high voltage battery, there is a risk of electric shock, electric leakage, or similar accidents if the Nissan Ariya vehicle is handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

ENVIRONMENT FOR LI-ION BATTERY DISASSEMBLY WORK

Must be an indoor environment.

  • The environment must utilize a shutter or other means to shut out the outside environment and prevent rain, snow, dust, or other substances from entering.

  • The environment must not cause the intrusion of sweat during work, or cause condensation to occur due to high temperature or humidity.

Metal powder, grease, and other foreign substances must not enter.

  • The indoor environment must also prevent metal powder, grease, and other foreign substances from entering due to maintenance performed on other Nissan Ariya vehicles and other sources during disassembly work.

  • During disassembly without internal work, temporarily close the battery pack upper case or cover it with an insulating cover.

The floor must be dry.

  • The floor must not be wet as a result of factors such as Nissan Ariya vehicle entry during rain or snow.

Work space

  • The work space must be approximately the size of one entire Nissan Ariya vehicle.

  • Take appropriate countermeasures so that persons other than the operator do not enter the work space, such as by placing signs indicating that disassembly work is in progress.

Standard fire fighting equipment

  • Always place a standard fire fighting equipment in the disassembly work area.

  • Depending on type of fire (Nissan Ariya vehicle or battery) use standard fire fighting equipment (water or extinguisher).

VEHICLE COMMUNICATION HARNESS

DISASSEMBLY

Remove service plug bracket assembly. Refer to Disassembly & Assembly.

Remove battery upper floor assembly. Refer to Disassembly & Assembly.

Remove each busbar. Refer to Disassembly & Assembly.

Remove battery junction box.

Remove harness connector from module.

Remove bolts and then remove brackets.

Remove bolts .

Open busbar terminal table and then remove nut .

Remove connectors , and .

Remove Nissan Ariya vehicle communication harness from battery pack lower case.

If necessary, Remove bracket from Nissan Ariya vehicle communication harness.

ASSEMBLY

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

HIGH-VOLTAGE HARNESS CONNECTOR

DISASSEMBLY

Remove interlock detecting harness connector .

Open cap and then remove bolt .

Remove bolts and then remove high-voltage harness connector .

Remove another high-voltage harness connector in the same way.

Assembly.

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

BUABAR 1 AND BUSBAR 24

DISASSEMBLY

Remove high-voltage harness connector.

Remove nut cap

Remove bolt and then remove busbar 1 .

Remove busbar 24 in the same way.

Assembly.

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

BATTERY JUNCTION BOX

DISASSEMBLY

Remove high-voltage harness connector.

Remove busbar 1 and busbar 24.

Remove busbar 2 and busbar 23. Refer to Disassembly & Assembly.

Remove busbar 41 and busbar 47. Refer to Disassembly & Assembly.

Remove clip and then push Nissan Ariya vehicle communication harness connector in the battery pack lower case.

Remove bolts .

Remove harness connector of battery pack pressure sensor and harness connector of battery pack water temperature sensor.

Remove harness connector of battery pack pressure sensor.

Remove connector harness of Nissan Ariya vehicle communication harness.

Remove nuts of battery junction box.

Lift battery junction box and release claws on upper cover of battery junction box.

Remove harness clips from battery junction box.

Assembly

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

Install upper cover to battery junction box .

Install battery junction box to battery pack lower case.

BATTERY PACK PRESSURE SENSOR

DISASSEMBLY

Remove harness connector of battery pack pressure sensor.

Remove bolt and then remove battery pack pressure sensor .

Remove left battery pack pressure sensor in the same way.

ASSEMBLY

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

BATTERY PACK WATER TEMPERATURE SENSOR

DISASSEMBLY

Disconnect harness connector of battery pack water temperature sensor and battery pack pressure sensor.

Remove nut and then remove battery pack pressure sensor .

ASSEMBLY

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

Front Module Stack Nissan Ariya

Exploded View

Bracket Bracket Bracket
Module No.16 (MD16) Module No.15 (MD15) Module No.14 (MD14)
Module No.13 (MD13) Bracket Module No.4 (MD4)
Module No.3 (MD3) Module No.2 (MD2) Module No.1 (MD1)
: Comply with the assembly procedure when installing. Disassembly & Assembly
: N·m (kg-m, ft-lb)
,,: Indicates that the part is connected at points with same symbol in actual Nissan Ariya vehicle.

Disassembly & Assembly

DANGER:

Since hybrid vehicles and electric vehicles contain a high voltage battery, there is the risk of electric shock, electric leakage, or similar accidents if the high voltage component and Nissan Ariya vehicle are handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

ENVIRONMENT FOR LI-ION BATTERY DISASSEMBLY WORK

Must be an indoor environment.

  • The environment must utilize a shutter or other means to shut out the outside environment and prevent rain, snow, dust, or other substances from entering.

  • The environment must not cause the intrusion of sweat during work, or cause condensation to occur due to high temperature or humidity.

Metal powder, grease, and other foreign substances must not enter.

  • The indoor environment must also prevent metal powder, grease, and other foreign substances from entering due to maintenance performed on other Nissan Ariya vehicles and other sources during disassembly work.

  • During disassembly without internal work, temporarily close the battery pack upper case or cover it with an insulating cover.

The floor must be dry.

  • The floor must not be wet as a result of factors such as Nissan Ariya vehicle entry during rain or snow.

Work space

  • The work space must be approximately the size of one entire Nissan Ariya vehicle.

  • Take appropriate countermeasures so that persons other than the operator do not enter the work space, such as by placing signs indicating that disassembly work is in progress.

Standard fire fighting equipment

  • Always place a standard fire fighting equipment in the disassembly work area.

  • Depending on type of fire (Nissan Ariya vehicle or battery) use standard fire fighting equipment (water or extinguisher).

DISASSEMBLY

Remove battery upper case rear. [module No. 4 (MD4) and module No. 13 (MD13) only] Refer to Removal & Installation.

Remove battery upper floor assembly with module. [module No. 4 (MD4) and module No. 13 (MD13) only] Refer to Disassembly & Assembly.

Remove each busbar. Refer to Disassembly & Assembly.

Remove harness connector from module.

Remove bolt and then remove bracket .

Remove bracket bolts that contact to the module to be removed.

Remove bolt and then remove bracket .

Remove bolt . [module No.1 (MD1) or module No.16 (MD116) only]

Remove bolt . [module No.4 (MD4) or module No.13 (MD13) only]

Hang carabiners (service part: 299A3 5MP0A) in the lifting holes and install belt slinger.

Install temporarily module mounting bolt to terminal side by screwing several rotations.

Lifting load is applied to the module using the mobile floor crane (A).

Drive resin scraper (service parts: 299A3 5MP0A) (A) in gap filler with a resin hammer and pry left and right to peel the adhesion of gap filler.

  • Never pry except module end plate to prevent module from damaging, deforming and leaking liquid.

  • Never remove 2 modules or more to prevent battery pack from weight unbalance except replacement work of battery pack lower case.

Remove module that was temporarily installed to terminal side.

Hang carabiners (service part: 299A3 5MP0A) in the lifting holes and install belt slinger.

Remove module from battery lower case by lifting up 4 points of module with mobile floor crane.

Peel off gap filler from battery pack lower case.

ASSEMBLY

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

Check battery pack lower case inside for foreign material or peeled gap filler

Set gabari sheet to battery pack lower case as shown in the figure and then write lines on battery pack lower case with oil-based pen.

Cut the static mixer at the position shown in the figure.

After taking out cartridge from packing box, check the followings;

  • No evidence of liquid leakage in the packing box.

  • No liquid leakage from bottom of cartridge .

Set static mixer to cartridge.

Set cartridge to the gap filler gun [SST: BP2000400Z (J-53350)].

Attach guideline label to cartridge as shown in the figure.

Guideline label : C-108 ml

Apply gap filler in accordance with lines written on the battery pack lower case.

Install locate pin [SST: KV99119700 (J-53349)] to battery pack lower case.

Install module in the reverse order of removal.

Rear Module Stack Nissan Ariya 1st generation

Exploded View

Rear module stack 2nd floor

Bracket Bracket Bracket
Bracket Bracket Bracket
Bracket Module No.10 (MD10) Module No.9 (MD9)
Module No.8 (MD8) Module No.7 (MD7) Battery upper floor assembly
Seal Heat shield sheet Heat shield sheet
: Comply with the assembly procedure when installing. Disassembly & Assembly
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)

Rear module stack 1ST floor

Bracket Bracket Bracket
Bracket Bracket Module No.6 (MD6)
Module No.5 (MD5) Module No.12 (MD12) Module No.11 (MD11)
: Comply with the assembly procedure when installing. Disassembly & Assembly
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)

Disassembly & Assembly

DANGER:

Since hybrid vehicles and electric vehicles contain a high voltage battery, there is the risk of electric shock, electric leakage, or similar accidents if the high voltage component and Nissan Ariya vehicle are handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

ENVIRONMENT FOR LI-ION BATTERY DISASSEMBLY WORK

Must be an indoor environment.

  • The environment must utilize a shutter or other means to shut out the outside environment and prevent rain, snow, dust, or other substances from entering.

  • The environment must not cause the intrusion of sweat during work, or cause condensation to occur due to high temperature or humidity.

Metal powder, grease, and other foreign substances must not enter.

  • The indoor environment must also prevent metal powder, grease, and other foreign substances from entering due to maintenance performed on other Nissan Ariya vehicles and other sources during disassembly work.

  • During disassembly without internal work, temporarily close the battery pack upper case or cover it with an insulating cover.

The floor must be dry.

  • The floor must not be wet as a result of factors such as Nissan Ariya vehicle entry during rain or snow.

Work space

  • The work space must be approximately the size of one entire Nissan Ariya vehicle.

  • Take appropriate countermeasures so that persons other than the operator do not enter the work space, such as by placing signs indicating that disassembly work is in progress.

Standard fire fighting equipment

  • Always place a standard fire fighting equipment in the disassembly work area.

  • Depending on type of fire (Nissan Ariya vehicle or battery) use standard fire fighting equipment (water or extinguisher).

BATTERY UPPER FLOOR ASSEMBLY (WITH MODULE)

DISASSEMBLY

Remove battery pack upper case rear. Refer to Removal & Installation.

Remove service plug bracket. Refer to Disassembly & Assembly.

Remove the cell voltage detection harness connector and the interlock detecting switch (service plug ) harness connector .

: Battery front

Remove the bolt and bracket. And then temporary tighten the bolt .

: Battery front

Open the busbar cover . And then remove the bolt and nut.

: Battery front

Remove busbar 10 and busbar 16.

install carabiners (service part: 299A3 5MP0A) (A) in the lifting holes and belt slinger (B) to the lifting holes.

: Battery front

Remove bolts. And then remove battery upper floor assembly with module using the mobile floor crane (engine crane).

Remove the seal from battery pack lower case.

DISASSEMBLY

Check that heat shield sheet is still stuck back of battery upper floor assembly.

Install seal to battery upper floor assembly.

Install guide pin [SST: KV99119600 (J-53348)] (A) to the center of battery pack upper floor assembly.

Install battery pack upper floor assembly with module to battery pack lower case using the mobile floor crane.

Install bolts.

Remove guide pin [SST: KV99119600 (J-53348)] (A).

Assemble in the reverse order of disassembly.

MODULE (2ND FLOOR)

DISASSEMBLY

Remove battery pack upper case rear. Refer to Removal & Installation.

Remove service plug bracket. Refer to Disassembly & Assembly.

Remove each busbar. Refer to Disassembly & Assembly.

Remove harness connector from module.

Remove bracket bolts that contact to the module to be removed.

Remove bolt . And then remove bracket .

Hang carabiners (service part: 299A3 5MP0A) in the lifting holes and install belt slinger.

Install temporarily module mounting bolt to terminal side by screwing several rotations.

Lifting load is applied to the module using the mobile floor crane (engine crane) (A).

Pry resin scraper (service parts: 299A3 5MP0A) left and right to peel the adhesion of gap filler.

Remove module bolt that was temporarily installed to terminal side.

Hang carabiners (service part: 299A3 5MP0A) in the lifting holes and install belt slinger.

Remove module from battery upper floor assembly by lifting up 4 points of module with mobile floor crane (A).

Peel off gap filler from battery upper floor assembly.

When remove battery pack upper floor assembly, Remove all of mobile on 2nd floor.

Remove all of mounting bolt on battery pack upper floor assembly. And then remove battery pack upper floor assembly from battery pack lower case.

ASSEMBLY

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

Check back of battery upper floor assembly for foreign material or peeled gap filler

  • When the sheet is peeled or battery upper floor assembly is replaced, stick new heat shield sheet according to the following procedure.

Place the battery upper floor assembly on a pre-cured area so that the outside of the battery upper floor assembly is not damaged Wipe the surface of the battery upper floor assembly where the heat shield sheet are stuck with a dry cloth to remove oil and dust. If the temperature of the work space is 15 ℃ (59 °F)or less, heat the surface of the battery upper floor assembly where heat shield sheet are stuck to 15 - 50 ℃ (59 - 112 °F)with a heat gun or equivalent.
  • For the battery upper floor assembly, warm the surface where the heat shield sheet are stuck for at least 5 minutes so that the entire surface is at least 15 ℃ (59 °F).

  • Remove the release paper from the heat shield sheet, and then heat the side stuck to battery upper floor assembly for at least 1 minute so that its temperature is 15 ℃ (59 °F)or higher.

Stick the heat shield sheet , and to the battery upper floor assembly as shown in the figure.
After sticking the heat shield sheet, press the whole by hands.

Check battery upper floor assembly inside for foreign material or peeled gap filler

Set gauge template sheet to battery upper floor assembly as shown in the figure and then write lines on battery upper floor assembly with oil-based pen.

Cut the static mixer at the position shown in the figure.

After taking out cartridge from packing box, check the followings;

  • No evidence of liquid leakage in the packing box.

  • No liquid leakage from bottom of cartridge .

Set static mixer to cartridge.

Set cartridge to the gap filler gun [SST: BP2000400Z (J-53350)].

Attach guideline label to cartridge as shown in the figure.

Guideline label : B-84 ml

Apply gap filler in accordance with lines written on the battery pack lower case.

Install guide pin [SST: KV99119600 (J-53348)] to battery upper floor assembly.

Install module in the reverse order of removal.

MODULE (1ST FLOOR)

DISASSEMBLY

Remove battery pack upper case rear. Refer to Removal & Installation.

Remove battery upper floor assembly (With module).

Remove each busbar. Refer to Disassembly & Assembly.

Remove harness connector from module.

Remove bracket bolts that contact to the module to be removed.

Remove bolt . And then remove bracket .

Hang carabiners (service part: 299A3 5MP0A) in the lifting holes and install belt slinger.

Install temporarily module mounting bolt to terminal side by screwing several rotations.

Lifting load is applied to the module using the mobile floor crane (engine crane) (A).

Pry resin scraper (service parts: 299A3 5MP0A) left and right to peel the adhesion of gap filler.

Remove module bolt that was temporarily installed to terminal side.

Hang carabiners (service part: 299A3 5MP0A) in the lifting holes and install belt slinger.

Remove module from battery lower case by lifting up 4 points of module with mobile floor crane (A).

Peel off gap filler from battery pack lower case.

ASSEMBLY

Note the following items, and assemble in the reverse order of disassembly.

DANGER:
  • There is the danger of electric shock caused by contact with the terminals. Be sure to wear insulated protective gear and use insulated tools.

  • Because there is a danger of electric shock and fire, never allow bus bar to contact a wrong terminal.

    • If bus bar contacts a wrong terminal, the circuit becomes energized and a short may occur.

    • Always keep the bus bar cover closed until immediately before the installation of bus bar.

Check battery pack lower case inside for foreign material or peeled gap filler

Set gauge template sheet to battery pack lower case as shown in the figure and then write lines on battery pack lower case with oil-based pen.

Cut the static mixer at the position shown in the figure.

After taking out cartridge from packing box, check the followings;

  • No evidence of liquid leakage in the packing box.

  • No liquid leakage from bottom of cartridge .

Set static mixer to cartridge.

Set cartridge to the gap filler gun [SST: BP2000400Z (J-53350)].

Attach guideline label to cartridge as shown in the figure.

Guideline label : B-84 ml

Apply gap filler in accordance with lines written on the battery pack lower case.

Install guide pin [SST: KV99119600 (J-53348)] to battery pack lower case.

Install module in the reverse order of removal.