Removal and Installation

In this manual: Removal and Installation
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
~15min read
  • Rear Shock Absorber
  • Coil Spring
  • Radius Rod
  • Front Lower Link
  • Rear Lower Link
  • Rear Stabilizer
  • Suspension Arm
  • Rear Suspension Member

Rear Shock Absorber Nissan Ariya first Gen

REAR SHOCK ABSORBER : Exploded View

FOR 2WD MODELS

Cap Shock absorber mounting bracket Bound bumper
Shock absorber
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

FOR 4WD MODELS

Cap Shock absorber mounting bracket Bound bumper
Shock absorber
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

REAR SHOCK ABSORBER : Removal & Installation

REMOVAL

Remove tires. Refer to ROAD WHEEL TIRE : Removal and Installation.

Set jack (A) under front lower link.

Remove shock absorber mounting bolt (lower side).

Slowly lower jack, separate shock absorber from front lower link.

Remove mounting bolt of shock absorber and then remove shock absorber.

Remove cap from mounting bracket, if necessary.

Perform inspection after removal. Refer to REAR SHOCK ABSORBER : Inspection.

INSTALLATION

Note the following, and install in the reverse order of removal.

  • Perform final tightening of fixing parts at installation position (rubber bushing) to the Nissan Ariya vehicle , under unladen conditions with tires on level ground.

  • Perform inspection after installation. Refer to REAR SHOCK ABSORBER : Inspection.

  • After replacing the shock absorber, always follow the disposal procedure to discard the shock absorber. Refer to REAR SHOCK ABSORBER : Disposal.

REAR SHOCK ABSORBER : Disassembly & Assembly

DISASSEMBLY

  • When installing piston rod lock nut , secure the piston rod tip to prevent piston rod from turning.

  • Perform inspection after disassembly. Refer to REAR SHOCK ABSORBER : Inspection.

ASSEMBLY

Note the following, and install in the reverse order of removal.

  • Never damage shock absorber piston rod when removing components from shock absorber.

  • When fixing shock absorber with a vise, wrap a shop cloth around lower side of shock absorber to protect from damage. Never set the cylindrical part of shock absorber with a vise.

  • When installing piston rod lock nut , secure the piston rod tip to prevent piston rod from turning.

  • Perform inspection after assembly. Refer to REAR SHOCK ABSORBER : Inspection.

REAR SHOCK ABSORBER : Inspection

INSPECTION AFTER REMOVAL

Check rear shock absorber for deformation, crack, and damage.

INSPECTION AFTER DISASSEMBLY

Mounting Bracket

Check mounting bracket for deformation, crack and damage. Replace it if necessary.

Bound Bumper

Check bound bumper bracket for deformation, crack and damage. Replace it if necessary.

Shock Absorber

Check the following item of shock absorber, and replace it if necessary.

  • Shock absorber and bushing for deformation, cracks, and other damage.

  • Piston rod for damage, uneven wear, and distortion.

  • Oil leakage

INSPECTION AFTER ASSEMBLY

Check shock absorber for operation. Replace it if necessary.

INSPECTION AFTER INSTALLATION

Check wheel alignment. Refer to Wheel Alignment: Inspection.

REAR SHOCK ABSORBER : Disposal

Set shock absorber horizontally to the ground with the piston rod fully extracted.

Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position () from top as shown in the figure to release gas gradually.

Dimension A : 20 – 30 mm (0.79 – 1.18 in)

Drain oil from drilled hole by moving the piston rod several times.

Coil Spring Nissan Ariya 1st generation

COIL SPRING : Exploded View

Upper rubber seat Coil spring Lower rubber seat
Rear lower link
: Nissan Ariya Vehicle front

COIL SPRING : Removal & Installation

REMOVAL

Remove tires. Refer to ROAD WHEEL TIRE: Exploded View.

Remove rear diffuser front. Refer to Removal and Installation.

Set jack (A) to rear lower link .

Loosen rear lower link mounting bolt and nut (rear suspension member side).

Remove mounting bolt and nut of rear lower link (axle housing side).

Slowly lower jack, remove upper rubber seat and coil spring .

Remove lower rubber seat from rear lower link.

Perform inspection after removal. Refer to COIL SPRING : Inspection.

INSTALLATION

Note the following, and install in the reverse order of removal.

  • Install lower rubber seat by aligning its protrusion with the hole of rear lower link .

  • Install coil spring by aligning lower end of coil spring with lower rubber seat as shown in the figure.

    Dimension (A) : 5 mm (0.20 in) or less
    : Upper side
    : 4.5 turns
  • Perform final tightening of fixing parts at installation position (rubber bushing) to the Nissan Ariya vehicle, under unladen conditions with tires on level ground.

  • Perform inspection after installation. Refer to COIL SPRING : Inspection.

COIL SPRING : Inspection

INSPECTION AFTER ASSEMBLY

Check the rear lower link, upper rubber seat, lower rubber seat, and coil spring for deformation, cracks, damage. Replace it if necessary.

INSPECTION AFTER INSTALLATION

Check wheel alignment. Refer to Wheel Alignment: Inspection.

Radius Rod Nissan Ariya first Gen

RADIUS ROD : Exploded View

FOR 2WD MODELS

Rear suspension member Radius rod Axle housing
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

FOR 4WD MODELS

Rear suspension member Radius rod Axle housing
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

RADIUS ROD : Removal & Installation

REMOVAL

Remove tires. Refer to ROAD WHEEL TIRE : Removal and Installation.

Set jack to axle housing, and raise jack until the position where bolt of axle housing side can be pulled out.

Remove radius rod mounting bolt and nut .

Remove radius rod. Refer to RADIUS ROD : Exploded View.

Perform inspection after installation. Refer to RADIUS ROD : Inspection.

INSTALLATION

Note the following, and install in the reverse order of removal.

  • Perform final tightening of fixing parts at installation position (rubber bushing) to the Nissan Ariya vehicle, under unladen conditions with tires on level ground.

  • For parts unable to reuse, Refer to RADIUS ROD : Exploded View.

  • Perform inspection after installation. Refer to RADIUS ROD : Inspection.

RADIUS ROD : Inspection

INSPECTION AFTER REMOVAL

Check radius rod and bushing for deformation, cracks, and damage. Replace it if necessary.

INSPECTION AFTER INSTALLATION

Check wheel alignment. Refer to Wheel Alignment: Inspection.

Front Lower Link Nissan Ariya first Gen

FRONT LOWER LINK : Exploded View

FOR 2WD MODELS

Rear suspension member Eccentric disk Adjusting bolt
Front lower link Axle housing
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

FOR 4WD MODELS

Rear suspension member Eccentric disk Adjusting bolt
Front lower link Axle housing
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

FRONT LOWER LINK : Removal & Installation

REMOVAL

Remove tires. Refer to ROAD WHEEL TIRE : Removal and Installation.

Set jack to axle housing.

Remove rear diffuser front. Refer to Removal and Installation.

Remove rear shock absorber. REAR SHOCK ABSORBER : Removal and Installation.

Remove rear stabilizer. Refer to REAR STABILIZER : Removal and Installation.

Remove front lower link mounting bolts and nuts .

Remove front lower link from Nissan Ariya vehicle.

Perform inspection after removal. Refer to FRONT LOWER LINK : Inspection.

INSTALLATION

Note the following, and install in the reverse order of removal.

  • Perform final tightening of fixing parts at installation position (rubber bushing) to the Nissan Ariya vehicle , under unladen conditions with tires on level ground.

  • For non-reusable parts, Refer to FRONT LOWER LINK : Exploded View.

  • Perform inspection after installation. Refer to FRONT LOWER LINK : Inspection.

FRONT LOWER LINK : Inspection

INSPECTION AFTER REMOVAL

Check front lower link and bushing for deformation, crack, and damage. Replace it if necessary.

INSPECTION AFTER INSTALLATION

Check wheel alignment. Refer to Wheel Alignment: Inspection.

Rear Lower Link Nissan Ariya 1st generation

REAR LOWER LINK : Exploded View

FOR 2WD MODELS

Rear suspension member Adjusting bolt Eccentric disk
Rear lower link
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

FOR 4WD MODELS

Rear suspension member Adjusting bolt Eccentric disk
Rear lower link
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

REAR LOWER LINK : Removal & Installation

REMOVAL

Remove rear coil spring. Refer to COIL SPRING : Removal and Installation.

Remove front lower link mounting bolt .

Perform inspection after removal. Refer to COIL SPRING : Inspection.

INSTALLATION

Note the following, and install in the reverse order of removal.

  • Perform final tightening of fixing parts at installation position (rubber bushing) to the Nissan Ariya vehicle , under unladen conditions with tires on level ground.

  • For parts unable to reuse, Refer to REAR LOWER LINK : Exploded View.

  • Perform inspection after installation. Refer to REAR LOWER LINK : Inspection.

REAR LOWER LINK : Inspection

INSPECTION AFTER REMOVAL

Check lower link and bushing for deformation, cracks, and damage. Replace it if necessary.

INSPECTION AFTER INSTALLATION

Check wheel alignment. Refer to Wheel Alignment: Inspection.

Rear Stabilizer Nissan Ariya

REAR STABILIZER : Exploded View

FOR 2WD MODELS

Rear suspension arm Rear stabilizer bar Rear stabilizer bushing
Rear stabilizer clamp Rear stabilizer connecting rod
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

FOR 4WD MODELS

Rear suspension arm Rear stabilizer bar Rear stabilizer bushing
Rear stabilizer clamp Rear stabilizer connecting rod
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

REAR STABILIZER : Removal & Installation

REMOVAL

Remove rear diffuser front. Refer to Removal and Installation.

Remove Li-ion battery under cover (rear). Refer to Removal and Installation (For 66 KWH) and Removal and Installation (For 91 KWH).

Remove rear shock absorber. Refer to REAR SHOCK ABSORBER : Removal and Installation.

Remove stabilizer connecting rod mounting nut .

Remove stabilizer clamp mounting bolts and then remove stabilizer from suspension member.

Perform inspection after removal. Refer to REAR STABILIZER : Inspection.

INSTALLATION

Note the following, and install in the reverse order of removal.

  • Perform final tightening of rubber bushes at installation position to the vehicle, under unladen conditions with tires on level ground.

  • For the parts unable to reuse, Refer to REAR STABILIZER : Exploded View.

  • Perform inspection after installation. Refer to REAR STABILIZER : Inspection.

REAR STABILIZER : Inspection

INSPECTION AFTER REMOVAL

Check stabilizer bar, stabilizer link, stabilizer bushing and stabilizer clamp for deformation, cracks or damage. Replace any one if necessary.

INSPECTION AFTER INSTALLATION

Check wheel alignment. Refer to WHEEL ALIGNMENT : Service Data.

Suspension Arm Nissan Ariya SUV

SUSPENSION ARM : Exploded View

FOR 2WD MODELS

Stopper rubber Rear suspension member Rear suspension arm
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

FOR 4WD MODELS

Stopper rubber Rear suspension member Rear suspension arm
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

SUSPENSION ARM : Removal & Installation

REMOVAL

Remove suspension member. Refer to REAR SUSPENSION MEMBER : Removal and Installation.

Remove suspension arm mounting bolts and nuts and then remove suspension arm from suspension member .

Perform inspection after removal. Refer to SUSPENSION ARM : Inspection.

INSTALLATION

Note the following, and install in the reverse order of removal.

  • Perform final tightening of fixing parts at installation position (rubber bushing) to the Nissan Ariya vehicle, under unladen conditions with tires on level ground.

  • For the parts unable to reuse, Refer to SUSPENSION ARM : Exploded View.

  • Perform inspection after installation. Refer to SUSPENSION ARM : Inspection.

SUSPENSION ARM : Inspection

INSPECTION AFTER REMOVAL

Check suspension arm and bushing for deformation, cracks or damage. Replace any one if necessary.

INSPECTION AFTER INSTALLATION

Check wheel alignment. Refer to WHEEL ALIGNMENT : Service Data.

Rear Suspension Member Nissan Ariya SUV

REAR SUSPENSION MEMBER : Exploded View

FOR 2WD MODELS

Rear suspension member Rear suspension member stay (right side) Rear suspension member stay (left side)
Rebound stopper
:N·m ( kg-m, ft-lb )

FOR 4WD MODELS

Rear suspension member Rear suspension member stay (right side) Mass damper
Motor mounting insulator Rebound stopper Rear suspension member stay (left side)
Rear suspension member stay (lower) Rear suspension bar
: Nissan Ariya Vehicle Front
:N·m ( kg-m, ft-lb )

REAR SUSPENSION MEMBER : Removal & Installation

REMOVAL

Remove tires. Refer to ROAD WHEEL TIRE : Removal and Installation.

Remove brake caliper and hang brake caliper in a place that does not interfere with the work.

Remove disc rotor. Refer to REAR WHEEL HUB : Removal and Installation.

Remove parking brake actuator and rear wheel sensor harness. Refer to PARKING BRAKE CONTROL : Removal and Installation.

Remove coil spring. Refer to COIL SPRING : Removal and Installation.

Remove rear diffuser front. Refer to Removal and Installation.

Remove rear lower link. Refer to REAR LOWER LINK : Removal and Installation.

Remove Li-ion battery under cover (rear). Refer to Removal and Installation (For 66 KWH) and Removal and Installation (For 91 KWH).

Remove rear shock absorber. Refer to REAR SHOCK ABSORBER : Removal and Installation.

Remove rear stabilizer assembly. Refer to REAR STABILIZER : Removal & Installation.

Remove front lower link. Refer to FRONT LOWER LINK : Removal and Installation.

Remove radius rod. Refer to RADIUS ROD : Removal and Installation.

Remove axle housing. Refer to REAR WHEEL HUB : Removal and Installation.

Set jack (A) to suspension member.

Remove rear suspension member stay.

Remove mounting bolt of rear suspension member. Refer to REAR SUSPENSION MEMBER : Exploded View.

Slowly lower jack and remove rear suspension member and rebound stopper.

Remove rear suspension member from Nissan Ariya vehicle.

Remove suspension arm. Refer to SUSPENSION ARM : Removal and Installation.

Perform inspection after removal. Refer to REAR SUSPENSION MEMBER : Inspection.

INSTALLATION

Note the following, and install in the reverse order of the removal.

  • Perform final tightening of rubber bushing at installation position to the vehicle, under unladen conditions with tires on level ground.

  • If replacement of mounting nuts of Li-ion battery side of right and left member stay front side are required, Refer to Removal and Installation (For 66 KWH) and Removal and Installation (For 91 KWH).

  • Perform inspection after installation. Refer to REAR SUSPENSION MEMBER : Inspection.

REAR SUSPENSION MEMBER : Inspection

INSPECTION AFTER REMOVAL

Check rear suspension member for deformation, cracks, and damage. Replace it if necessary.

INSPECTION AFTER INSTALLATION

  • Check parking brake actuator harness and rear wheel sensor for proper connection. Refer to REAR WHEEL SENSOR : Exploded View.

  • Check wheel alignment. Refer to WHEEL ALIGNMENT : Service Data.