Dtc/circuit Diagnosis

In this manual: Dtc/circuit Diagnosis
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
30steps
~180min
5/5difficulty
Done 0 of 30
  • B0001-09 Driver Air Bag Module
  • B0091-86 Front Door Satellite Sensor
  • B0094-55 Crash Zone Sensor
  • B1000-49 Air Bag Diagnosis Sensor Unit
  • B1000-55 Air Bag Diagnosis Sensor Unit
  • B1036-16 Ignition Voltage
  • B1040-22 Vehicle Speed
  • B1041-82 Vehicle Speed Signal
  • B12b5-97 Frontal Collision Detection
  • U0073-00 Can Comm Circuit

B0001-09 Driver Air Bag Module Nissan Ariya 2023

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC Detection Condition
B0001-09 Driver Frontal Stage 1 Deployment Control Diagnosis condition When power switch is ON.
Signal (terminal) Driver air bag module signal
Threshold

Driver air bag module circuit is shorted to other

(including the spiral cable)
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

  • Connection malfunction or short circuit of harness and connector

  • Internal malfunction of driver air bag module

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

  1. Power switch ON.

  2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.

Is the inspection result normal?

YES>>

GO TO 2.

NO–1>>

Damage: Replace malfunctioning harness and connector.

NO–2>>

Disconnection or looseness: Securely lock the connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace malfunctioning harness and connector.

REPLACE SPIRAL CABLE

  1. Replace spiral cable. Refer to Removal & Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 4.

NO>>

INSPECTION END

REPLACE DRIVER AIR BAG MODULE

  1. Replace driver air bag module. Refer to Removal & Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 5.

NO>>

INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

>>

INSPECTION END

B0091-86 Front Door Satellite Sensor Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC Detection Condition
B0091-86 Left Side Restraints Sensor 1 Diagnosis condition When power switch is ON.
Signal (terminal) Front door satellite sensor LH signal
Threshold Front door satellite sensor LH is out of the specified specification
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

Air bag diagnosis sensor unit and front door satellite sensor LH is different from the part specified

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

  1. Power switch ON.

  2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

REPLACE FRONT DOOR SATELLITE SENSOR LH

  1. Replace front door satellite sensor LH. Refer to Removal & Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

>>

INSPECTION END

B0094-55 Crash Zone Sensor Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC Detection Condition
B0094-55 Center Frontal Restraints Sensor Diagnosis condition When power switch is ON.
Signal (terminal) Crash zone sensor signal
Threshold When a mismatch is detected between in the configuration data stored in the air bag diagnosis sensor unit and Nissan Ariya vehicle specification.
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

  • Connection malfunction of harness and connector

  • Mistake of configuration for air bag diagnosis sensor unit

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

  1. Power switch ON.

  2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.

Is the inspection result normal?

YES>>

GO TO 2.

NO–1>>

Damage: Replace malfunctioning harness and connector.

NO–2>>

Disconnection or looseness: Securely lock the connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace malfunctioning harness and connector.

PERFORM CONFIGURATION

  1. Perform configuration for air bag diagnosis sensor unit. Refer to Description.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 4.

NO>>

INSPECTION END

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

>>

INSPECTION END

B1000-49 Air Bag Diagnosis Sensor Unit Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC Detection Condition
B1000-49 Air bag diagnosis sensor unit Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold Air bag diagnosis sensor unit is malfunctioning
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

Malfunction in air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

  1. Power switch ON.

  2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

>>

INSPECTION END

B1000-55 Air Bag Diagnosis Sensor Unit Nissan Ariya 1st generation

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC Detection Condition
B1000-55 Air bag diagnosis sensor unit Diagnosis condition When power switch is ON.
Signal (terminal) —
Threshold When no data are stored in the air bag diagnosis sensor unit
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

Incomplete of configuration for air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

  1. Power switch ON.

  2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM CONFIGURATION

Perform configuration for air bag diagnosis sensor unit.

>>

Refer to Description.

B1036-16 Ignition Voltage Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC Detection Condition
B1036-16 Ignition voltage Diagnosis condition When power switch is ON.
Signal (terminal) Ignition low voltage signal
Threshold Power supply malfunction (low voltage) of air bag diagnosis sensor unit
Diagnosis delay time 10 seconds or more.

POSSIBLE CAUSE

  • Malfunction of battery voltage (9 V or less)

  • Connection malfunction of harness or connector

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

  1. Power switch ON and wait for 10 seconds or more.

  2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK BATTERY VOLTAGE

Check battery voltage. Refer to Work Flow.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the malfunctioning parts.

CHECK HARNESS CONNECTOR

Check the harness connector for disconnection, looseness or damage.

Is the inspection result normal?

YES>>

GO TO 3.

NO–1>>

Damage: Replace malfunctioning harness and connector.

NO–2>>

Disconnection or looseness: Securely lock the connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace malfunctioning harness and connector.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

>>

INSPECTION END

B1040-22 Vehicle Speed Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC Detection Condition
B1040-22 Nissan Ariya Vehicle speed Diagnosis condition When power switch is ON.
Signal (terminal) Nissan Ariya Vehicle speed signal
Threshold 300 km/h or more
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

  • Drive the vehicle at vehicle speed of 300 km/h or more.

  • VCM

  • Air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

  1. Power switch ON.

  2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

REPLACE VCM

  1. Replace VCM. Refer to VCM : Removal & Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

NO>>

INSPECTION END

B1041-82 Vehicle Speed Signal Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC Detection Condition
B1041-82 Nissan Ariya Vehicle speed signal Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold Error signal that is received from ABS actuator and electric unit (control unit)
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

  • ABS actuator and electric unit (control unit)

  • Air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC B1041-82 is displayed with DTC U0073-00, first perform the trouble diagnosis for DTC U0073-00.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

CHECK SELF-DIAG RESULT

With CONSULT

  1. Power switch ON.

  2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC B1041-82 is displayed with DTC U0073-00, first perform the trouble diagnosis for DTC U0073-00.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS

Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.

Is any DTC detected?

YES>>

Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to DTC Index.

NO>>

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

B12b5-97 Frontal Collision Detection Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC Detection Condition
B12B5-97 Frontal collision Diagnosis condition When power switch is ON.
Signal (terminal) Collision signal
Threshold Frontal collision detected
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

Frontal collision

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

  1. Power switch ON.

  2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM COLLISION DIAGNOSIS

Perform collision diagnosis. Refer to When SRS is activated in a collision or When SRS is not activated in a collision.

>>

GO TO 2.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

When DTC B12B5-97 is detected, replace air bag diagnosis sensor unit.

>>

Replace air bag diagnosis sensor unit. Refer to Removal & Installation.

U0073-00 Can Comm Circuit Nissan Ariya

DTC Description

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Ariya vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Ariya vehicle is equipped with many electronic control unit, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN H-line, CAN L-line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC Detection Condition
U0073-00 Control Module Communication Bus "A" Off Diagnosis condition When power switch is ON.
Signal (terminal) CAN communication signal
Threshold Air bag diagnosis sensor unit cannot communicate CAN communication signal.
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

With CONSULT

  1. Power switch ON and wait for 2 seconds or more.

  2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK CAN COMMUNICATION SYSTEM

Check CAN communication system. Refer to Trouble Diagnosis Flow Chart.

>>

INSPECTION END