Removal and Installation

In this manual: Removal and Installation
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
14steps
~84min
5/5difficulty
Done 0 of 14
  • Front Bumper
  • Rear Bumper
  • Front Grille
  • Active Grille Shutter
  • Cowl Top
  • Fender Finisher
  • Fillet Molding
  • Front Fillet Molding
  • Rear Fillet Molding
  • Fender Protector
  • Rear Wheel House Protector
  • Front Under Cover
  • Rear Diffuser
  • Roof Rail
  • Door Sash Cover
  • Front Door Sash Cover
  • Rear Door Sash Cover
  • Door Outside Molding
  • Front Door Outside Molding
  • Side Guard Molding
  • Front Side Guard Molding
  • Rear Side Guard Molding
  • Rear Deflector
  • Sill Cover
  • Rear Fender Cover
  • Rear Spoiler
  • Emblem

Front Bumper Nissan Ariya SUV

Exploded View

Front bumper side bracket RH Front bumper stay RH Front bumper reinforcement
sensor bracket Front bumper reinforcement lower Front bumper energy absorber
Front bumper energy absorber lower Front bumper grille RH Front bumper finisher RH
Bumper bracket cover License plate bracket Front bumper finisher LH
Front bumper grille LH U nut Front bumper fascia assembly
Front bumper clip Front bumper side finisher LH Front bumper bracket LH
Front fog lamp LH Front bumper side bracket LH Plastic nut
Front bumper stay LH Front bumper side finisher RH Front bumper bracket RH
Front fog lamp RH Front bumper fascia J nut
Front bumper fascia lower
: Pawl
: Nissan Ariya Vehicle front
, , , , , , , , : Indicates that the part is connected at points with same symbol in actual Nissan Ariya vehicle.

Removal & Installation

REMOVAL

Remove front grille. Refer to Removal & Installation.

Remove front side of front fillet molding (LH and RH). Refer to Removal & Installation.

Disconnect front combination lamp harness connector and .

Remove front under cover mounting bolts .

Remove air guide from fender protector. Refer to Removal & Installation.

Remove fender protector fixing screws .

Remove front bumper fascia assembly fixing clips .

Remove front bumper fascia assembly fixing screw .

Apply protective tapes (A) on the part to protect it from damage.

Pull front bumper fascia side toward the Nissan Ariya vehicle side to disengage the fitting of bumper side bracket.

: Pawl

While holding part of front combination lamp, pull front bumper fascia assembly and front combination lamp toward front of Nissan Ariya vehicle to disengage them from head lamp.

: Pawl

Disconnect harness connector.

Disconnect headlamp washer tube from headlamp washer nozzle.(LH and RH). (if equipped)

Remove front bumper fascia assembly.

Remove the following parts after removing front bumper fascia.

  • Front combination lamp. Refer to Removal & Installation.

  • Front fog lamp. Refer to Removal & Installation.

  • Front sonar sensor (if equipped) Refer to SONAR SENSOR (FRONT) : Removal & Installation.

  • Headlamp washer nozzle (if equipped)

  • Front bumper finisher

  • Front bumper side finisher

  • Front bumper bracket

  • Front bumper grille

  • Front bumper fascia

  • Front bumper fascia lower

  • Bumper bracket cover

  • License plate bracket.

Remove front bumper energy absorber and front bumper energy absorber lower.

Remove active grille shutter. Refer to Removal & Installation.

Remove front bumper reinforcement lower mounting nuts and harness clips, and then remove front bumper reinforcement lower.

Remove radiator air guide (LH and RH). Refer to Removal & Installation.

Remove distance sensor. Refer to Removal and Installation.

Remove front bumper reinforcement mounting bolts and harness clips, and then remove front bumper reinforcement.

Remove front bumper stay mounting bolts, and then remove front bumper stay.

Remove front bumper side bracket fixing screws, and then remove front bumper side bracket.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

PortionClearanceSurface height difference
Front bumper fascia assembly – Front grille –

0.2 – 2.8 mm

(0.008 – 0.110 in)

(−2.3) – (+0.3) mm

[(-0.091) - (+0.012) in]
Front bumper molding – Front combination lamp –

0.2 – 2.8 mm

(0.008 – 0.110 in)
–
–

0.0 – 2.3 mm

(0.008 – 0.091 in)
–
Front bumper fascia assembly – Front fender assembly –

0.0 – 1.0 mm

(0.000 – 0.039 in)

(−1.7) – (+0.3) mm

[(-0.067) - (+0.012) in]

Inspection

SIDE RADAR IRRADIATION AREA

  • For side radar irradiation area, refer to the figure below.

    Front bumper fascia Front bumper fascia lower
    Side radar irradiation area Reference point
    C 50 mm (edge line) D 120 mm (edge line) E 240 mm (apex of character line)
    F 260 mm (horizontal line) G 110 mm (Reference dimansions)

  • The dimensions are along the bumper fascia surface between each reference point.

  • Since it may affect side radar performance, for repair and mending of front bumper refer to repair and mending of side radar irradiation area.

REPAIR AND MENDING OF IRRADIATION AREA OF SIDE RADAR

  • Do not leave cracks, scratches and deformations in the side radar irradiation area.

  • Since it affects side radar performance, there are following restrictions on the various construction on front bumper of the Nissan Ariya vehicle equipped with side radar.

    Construction item of side radar irradiation area Can be constructed and cannot be constructed Supplement
    1 Installation of stickers, accessories, aluminum tape and wrapping film, etc. Cannot be constructed Prohibited including transparent ones
    2 Coating and wax, etc. Can be constructed Construct according to the contents of construction manual
    3 Repairing of cuts, holes, cracks, scratches and deformations Cannot be constructed -
    4 Paint repair Putty applying Cannot be constructed -
    Color base painting *1 Can be constructed (with conditions)
    • When remove existing paint film within the irradiation area, color base can be constructed only once (No recoating, No painting other than the body exterior paint colors which are adopted for this model.) *1:Color base includes primer for plastic and primer surfacer

    • When color base painting in the side radar irradiation area even if bumper fascia is not removed and installed, conduct side radar adjustment after the painting

    Clear painting Can be constructed (with conditions)
    • When the clear paint film is uniformly block coated within the irradiation area, it is possible to construct only once (No clear paint fading-out or recoating within irradiation area)

    • When clear painting in the side radar irradiation area even if bumper fascia is not removed and installed, conduct side radar adjustment after the painting

    5 Dust on the paint surface removal by polishing, polishing, buffing and base treatment before coating Can be constructed -

For details of each construction item, refer to followings.

  1. Installation of sticker, accessories, aluminum tape and wrapping film, etc.

    Do not install sticker, accessories, aluminum tape and wrapping tape, etc. to side radar irradiation area. (Including transparent one)

  2. Coating and wax, etc.

    • It is possible to apply coating and wax to side radar irradiation area.

    • It is also possible to polish before construction.

  3. Repair of cuts, holes, cracks, scratches and deformations

    It is not possible to repair fissures, holes, cracks, scratches and deformations within side radar irradiation area. Therefore be sure to replace it with a new front bumper fascia. Refer to Removal & Installation.

    Cannot be constructed

    Side radar
    Irradiation area Existing paint film Bumper fascia plastic

  4. Paint repair

    Putty application: Construction is impossible

    • It is impossible to apply putty within side radar irradiation area. (Both partial application and full application are prohibited)

    Color base painting: Construction is possible (with conditions)

    • When removing existing paint firm within irradiation area or when it is new unpainted bumper.

    • When removing existing paint film, use finer sandpaper than #800.

    • When there is unevenness due to scratches on the surface after removing existing paint film, replace it with a new bumper.

    • Color base painting (Includes primer for plastic parts and primer surfacer) within side radar irradiation area is possible only once. (Definition of once is until the color base painting is dyed, not number of sprays)

    • Only the body exterior paint color, which are adopted for this model, painting can be constructed. (Do not paint more thickness than necessary)

    • Only the approved paint suppliers, products and color formulator can be constructed. For additional information, please contact each paint supplier which body shop uses.

    • When applying primer surfacer, use each gray shade undercoat color, which paint supplier recommends, for improving the hiding of color base and reducing color base thickness.

    • When spray mist may stick on the reverse side of the bumper fascia, conduct masking on the reverse side of the bumper fascia.

    • Step 1:Before repair

      Can be constructed

      Side radar
      Irradiation area Existing paint film Bumper fascia plastic

    • Step 2: After removing existing paint film

      Can be constructed

      Side radar
      Irradiation area Existing paint film Bumper fascia plastic

    • Step 3:After constructing color base painting and clear painting

      Can be constructed

      Side radar
      Irradiation area Existing paint film Bumper fascia plastic
      Clear paint film Color base paint film

    Color base painting: The conditions that construction is impossible

    • When painting on existing paint film. (Both block painting and fade-out painting are prohibited)

      Cannot be constructed

      Side radar
      Irradiation area Clear paint film Color base paint film
      Existing paint film *1 Bumper fascia plastic

      *1:It cannot be constructed when existing paint film is remains.

    • When recoat color base painting (No recoating)

      Cannot be constructed

      Side radar
      Irradiation area Clear paint film Color base paint film
      Bumper fascia plastic

    Clear painting: Can be constructed (With conditions).

    • It is possible to apply clear paint only once on the existing paint film (including the paint film of the color bumper replaced with a new one) for the side radar irradiation area. *Definition of once:It is once until the clear coating is formed. (It is not number of sprays)

    • The conditions that clear coating is possible are as follows.

    • When color base painting area (primer for plastic parts, putty, primer surfacer, pearl base, color clear base and under clear, etc.) does not cover the irradiation area and clear paint is uniformly block painting.

      Can be constructed

      Side radar
      Irradiation area Clear paint film Color base paint film
      Existing paint film Bumper fascia plastic

    • When clear paint is uniformly block painting in the irradiation area. (Painting whole the parts)

      Can be constructed

      Side radar
      Irradiation area Clear paint film Existing paint film
      Bumper fascia plastic

    Clear painting: The conditions that construction is impossible.

    • When clear paint is not uniformly block painting in the irradiation area. (Clear paint fade-out is prohibited)

      Cannot be constructed

      Side radar
      Irradiation area Clear paint film Color base paint film
      Existing paint film Bumper fascia plastic

    • When re-paint the clear paint in the irradiation area.

      Cannot be constructed

      Side radar
      Irradiation area Clear paint film Existing paint film
      Bumper fascia plastic

  5. Polishing on paint surface

    Polishing is possible. (For dust on the paint surface removal, gloss improvement, base treatment before coating and so on.)

Rear Bumper Nissan Ariya 2023

Exploded View

Rear bumper side bracket LH Rear bumper bracket cover Rear bumper bracket clip
Rear bumper bracket Rear bumper fascia assembly Rear reflex reflector LH
Bumper bracket cover Rear combination lamp cover lower LH Rear reflex reflector RH
Rear combination lamp cover lower RH Rear bumper energy absorber Rear bumper reinforcement
Grommet Rear bumper side bracket RH Rear bumper fascia
U nut Rear bumper fascia lower
: Pawl
: Nissan Ariya Vehicle front
Always replace after every disassembly.
, , , , , : Indicates that the part is connected at points with same symbol in actual Nissan Ariya vehicle.

Removal & Installation

REMOVAL

Fully open back door.

Remove rear combination lamp (body side). Refer to Removal & Installation.

Apply protective tape (A) on the part to protect it from damage.

Disengage rear combination lamp cover lower fixing pawls using a remover tool (A), and then remove rear combination lamp cover lower.

: Pawl

Remove rear bumper fascia assembly fixing clip and mounting bolt .

Remove rear bumper fascia assembly fixing clips of bumper lower side.

Remove rear bumper fascia assembly fixing clip and mounting bolt .

Remove back side of rear fillet molding (LH and RH). Refer to Removal & Installation.

Remove rear bumper fascia assembly fixing screw .

Apply protective tape (A) on the part to protect it from damage.

Pull rear bumper fascia assembly side toward the Nissan Ariya vehicle side to disengage the fitting of rear bumper side bracket and rear bumper fascia assembly side according to the numerical order 1→2 as shown by the arrows in the figure.

: Pawl

Disconnect harness connector.

Remove rear bumper fascia assembly.

Remove the following parts after removing rear bumper fascia assembly.

  • Rear reflex reflector. Refer to Removal & Installation.

  • Side radar (if equipped). Refer to Removal and Installation.

  • Rear sonar sensor (if equipped). Refer to SONAR SENSOR (REAR) : Removal & Installation.

  • Back door hands free sensor (if equipped). Refer to Removal & Installation.

  • Rear bumper bracket cover.

  • Rear bumper bracket clip.

  • Rear bumper bracket.

  • Bumper bracket cover.

  • Rear bumper fascia.

  • Rear bumper fascia lower.

Remove rear bumper energy absorber.

Remove rear bumper reinforcement mounting bolts, and then remove rear bumper reinforcement.

Remove rear bumper side bracket fixing screws, and then remove rear bumper side bracket (LH and RH).

INSTALLATION

Note the following items, and then install in the reverse order of removal.

PortionClearanceSurface height difference
Rear bumper fascia assembly – Rear fender –

0.0 – 1.0 mm

(0.000 – 0.039 in)

(−1.7) – (+0.3) mm

[(–0.067) – (+0.012) in]
Rear bumper fascia assembly – Rear combination lamp –

0.0 – 3.0 mm

(0.000 – 0.118 in)
–
Rear bumper fascia assembly – Back door panel –

2.8 – 7.2 mm

(0.110 – 0.283 in)

(−0.5) – (+3.5) mm

[(–0.020) – (+0.138) in]
–

5.5 – 9.5 mm

(0.217 – 0.374) in

(−0.8) – (+3.8) mm

[(–0.031) – (+0.150) in]

Inspection

SIDE RADAR IRRADIATION AREA

  • For side radar irradiation area, refer to the figure below.

    Rear bumper fascia Rear bumper fascia lower
    Side radar irradiation area Reference point
    C 310 mm (apex of character line) D 225 mm (horizontal line) E 100 mm (vertical line)
    F 20 mm (vertical line, reference dimensions) G 130 mm (horizontal line, reference dimensions) H 115 mm (apex of character line, reference dimensions)

  • The dimensions are along the bumper fascia surface between each reference point.

  • Since it may affect side radar performance, for repair and mending of rear bumper refer to repair and mending of side radar irradiation area.

REPAIR AND MENDING OF IRRADIATION AREA OF SIDE RADAR

  • Do not leave cracks, scratches and deformations in the side radar irradiation area.

  • Since it affects side radar performance, there are following restrictions on the various construction on rear bumper of the Nissan Ariya vehicle equipped with side radar.

    Construction item of side radar irradiation area Can be constructed and cannot be constructed Supplement
    1 Installation of stickers, accessories, aluminum tape and wrapping film, etc. Cannot be constructed Prohibited including transparent ones
    2 Coating and wax, etc. Can be constructed Construct according to the contents of construction manual
    3 Repairing of cuts, holes, cracks, scratches and deformations Cannot be constructed -
    4 Paint repair Putty applying Cannot be constructed -
    Color base painting *1 Can be constructed (with conditions)
    • When remove existing paint film within the irradiation area, color base can be constructed only once (No recoating, No painting other than the body exterior paint colors which are adopted for this model.) *1:Color base includes primer for plastic and primer surfacer

    • When color base painting in the side radar irradiation area even if bumper fascia is not removed and installed, conduct side radar adjustment after the painting

    Clear painting Can be constructed (with conditions)
    • When the clear paint film is uniformly block coated within the irradiation area, it is possible to construct only once (No clear paint fading-out or recoating within irradiation area)

    • When clear painting in the side radar irradiation area even if bumper fascia is not removed and installed, conduct side radar adjustment after the painting

    5 Dust on the paint surface removal by polishing, polishing, buffing and base treatment before coating Can be constructed -

For details of each construction item, refer to followings.

  1. Installation of sticker, accessories, aluminum tape and wrapping film, etc.

    Do not install sticker, accessories, aluminum tape and wrapping tape, etc. to side radar irradiation area. (Including transparent one)

  2. Coating and wax, etc.

    • It is possible to apply coating and wax to side radar irradiation area.

    • It is also possible to polish before construction.

  3. Repair of cuts, holes, cracks, scratches and deformations

    It is not possible to repair fissures, holes, cracks, scratches and deformations within side radar irradiation area. Therefore be sure to replace it with a new rear bumper fascia. Refer to Removal & Installation.

    Cannot be constructed

    Side radar
    Irradiation area Existing paint film Bumper fascia plastic

  4. Paint repair

    Putty application: Construction is impossible

    • It is impossible to apply putty within side radar irradiation area. (Both partial application and full application are prohibited)

    Color base painting: Construction is possible (with conditions)

    • When removing existing paint firm within irradiation area or when it is new unpainted bumper.

    • When removing existing paint film, use finer sandpaper than #800.

    • When there is unevenness due to scratches on the surface after removing existing paint film, replace it with a new bumper.

    • Color base painting (Includes primer for plastic parts and primer surfacer) within side radar irradiation area is possible only once. (Definition of once is until the color base painting is dyed, not number of sprays)

    • Only the body exterior paint color, which are adopted for this model, painting can be constructed. (Do not paint more thickness than necessary)

    • Only the approved paint suppliers, products and color formulator can be constructed. For additional information, please contact each paint supplier which body shop uses.

    • When applying primer surfacer, use each gray shade undercoat color, which paint supplier recommends, for improving the hiding of color base and reducing color base thickness.

    • When spray mist may stick on the reverse side of the bumper fascia, conduct masking on the reverse side of the bumper fascia.

    • Step 1:Before repair

      Can be constructed

      Side radar
      Irradiation area Existing paint film Bumper fascia plastic

    • Step 2: After removing existing paint film

      Can be constructed

      Side radar
      Irradiation area Existing paint film Bumper fascia plastic

    • Step 3:After constructing color base painting and clear painting

      Can be constructed

      Side radar
      Irradiation area Existing paint film Bumper fascia plastic
      Clear paint film Color base paint film

    Color base painting: The conditions that construction is impossible

    • When painting on existing paint film. (Both block painting and fade-out painting are prohibited)

      Cannot be constructed

      Side radar
      Irradiation area Clear paint film Color base paint film
      Existing paint film *1 Bumper fascia plastic

      *1:It cannot be constructed when existing paint film is remains.

    • When recoat color base painting (No recoating)

      Cannot be constructed

      Side radar
      Irradiation area Clear paint film Color base paint film
      Bumper fascia plastic

    Clear painting: Can be constructed (With conditions).

    • It is possible to apply clear paint only once on the existing paint film (including the paint film of the color bumper replaced with a new one) for the side radar irradiation area. *Definition of once:It is once until the clear coating is formed. (It is not number of sprays)

    • The conditions that clear coating is possible are as follows.

    • When color base painting area (primer for plastic parts, putty, primer surfacer, pearl base, color clear base and under clear, etc.) does not cover the irradiation area and clear paint is uniformly block painting.

      Can be constructed

      Side radar
      Irradiation area Clear paint film Color base paint film
      Existing paint film Bumper fascia plastic

    • When clear paint is uniformly block painting in the irradiation area. (Painting whole the parts)

      Can be constructed

      Side radar
      Irradiation area Clear paint film Existing paint film
      Bumper fascia plastic

    Clear painting: The conditions that construction is impossible.

    • When clear paint is not uniformly block painting in the irradiation area. (Clear paint fade-out is prohibited)

      Cannot be constructed

      Side radar
      Irradiation area Clear paint film Color base paint film
      Existing paint film Bumper fascia plastic

    • When re-paint the clear paint in the irradiation area.

      Cannot be constructed

      Side radar
      Irradiation area Clear paint film Existing paint film
      Bumper fascia plastic

  5. Polishing on paint surface

    Polishing is possible. (For dust on the paint surface removal, gloss improvement, base treatment before coating and so on.)

Front Grille Nissan Ariya

Exploded View

Front grille upper Front grille Front emblem bracket
Front emblem Front camera (if equipped)
: Pawl

Removal & Installation

REMOVAL

Fully open hood assembly.

Remove front grille upper mounting bolts and fixing clips .

Remove front grille upper fixing screws on the back of front grille, and then remove front grille upper.

Apply protective tapes (A) on the part to protect it from damage.

Disengage front grille fixing pawls from back side while pulling front grille toward Nissan Ariya vehicle front.

: Pawl

Disconnect front camera and distance sensor harness connector. (if equipped)

Remove front grille.

Remove the following parts after removing front grille.

  • Front camera (if equipped). Refer to Removal and Installation.

  • Distance sensor. Refer to Removal and Installation.

  • Front emblem.

  • Front emblem bracket.

INSTALLATION

Note the following item, and then install in the reverse order of removal.

Active Grille Shutter Nissan Ariya 2023

Exploded View

Front bumper reinforcement Front bumper reinforcement lower Active grille shutter

Removal & Installation

REMOVAL

Remove front bumper energy absorber and front bumper energy absorber lower. Refer to Removal & Installation.

Remove ambient sensor. Refer to Removal and Installation.

Disconnect harness connector .

Disconnect active grille shutter harness connector .

Remove active grille shutter fixing clips .

Disconnect harness connector.

Remove harness clips, and then remove active grille shutter.

INSTALLATION

Install in the reverse order of removal.

Cowl Top Nissan Ariya first Gen

Exploded View

Cowl top seal Cowl top cover Cap
Cowl top member Cowl top extension Cowl top stay
EPT seal [t: 5.0 mm (0.197 in)]
: Clip
: Always replace after every disassembly.

Removal & Installation

REMOVAL

Fully open hood assembly.

Remove front wiper arm. Refer to Removal & Installation.

Remove fender cover. Refer to Removal & Installation.

Remove cowl top cover fixing clips .

Remove harness clip . (if equipped)

Pull forward to release cowl top cover from windshield glass.

Remove front washer tube B from joint, and then remove cowl top cover.

Remove the following parts after removing cowl top cover.

  • Front washer tube B. Refer to Removal & Installation.

  • Tube connector. Refer to Removal & Installation.

  • EPT seal

  • Cowl top seal

Remove front wiper drive assembly. Refer to Removal & Installation.

Remove cowl top stay mounting bolts, and then remove cowl top stay.

Remove high voltage power delivery assembly. Refer to HIGH VOLTAGE POWER DELIVERY ASSEMBLY : Removal & Installation.

Remove cowl top member mounting bolts, nuts and harness clip, and then remove cowl top member.

Remove cowl top extension mounting bolts, and then remove cowl top extension.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

Fender Finisher Nissan Ariya

Exploded View

Fender finisher
: Clip

Removal & Installation

REMOVAL

Fully open front door.

Apply protective tapes (A) on the part to protect it from damage.

Remove fender finisher fixing clips using a remover tool (A), and then remove fender finisher.

: Clip

INSTALLATION

Install in the reverse order of removal.

Fillet Molding Nissan Ariya first Gen

Exploded View

Grommet Front fillet molding Double-sided tape [t : 1.2 mm (0.047 in)]
Rear fillet molding
: Clip
: Pawl
: Nissan Ariya Vehicle front
: Always replace after every disassembly.

Front Fillet Molding Nissan Ariya first Gen

Removal & Installation

REMOVAL

Remove front fillet molding fixing clips .

Disengage front fillet molding fixing pawls according to numerical order 1→2 indicated by arrows as shown in the figure.

:Pawl

Apply protective tape (A) on the part to protect it from damage.

Remove front fillet molding fixing clips using a remover tool (A), and then remove front fillet molding.

: Clip

Remove grommet after removing front fillet molding.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

Rear Fillet Molding Nissan Ariya: FE0

Removal & Installation

REMOVAL

Remove rear fillet molding fixing clips .

Disengage rear fillet molding fixing pawls according to numerical order 1→2 indicated by arrows as shown in the figure.

: Pawl

Apply protective tapes (A) on the part to protect it from damage.

Cut double-sided tape using a remover tool (A) and cutter (B).

Remove rear fillet molding fixing clips using a remover tool (A), and then remove rear fillet molding.

: Clip

Remove grommet after removing rear fillet molding.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

Fender Protector Nissan Ariya 2023

Exploded View

AIR GUIDE

Plastic nut Air guide
: Nissan Ariya Vehicle front
: N·m (kg-m, in-lb)

FENDER PROTECTOR

Fender protector Spring nut Screw grommet
: Nissan Ariya Vehicle front

Removal & Installation

REMOVAL

Remove air guide fixing screws and clip, and then remove air guide.

Remove mounting bolts that are fastened to front under cover. Refer to Removal & Installation.

Remove front fillet molding. Refer to Removal & Installation.

Remove front side of sill cover. Refer to Removal & Installation.

Remove fender protector fixing screws and clips, and then remove fender protector.

INSTALLATION

Install in the reverse order of removal.

Rear Wheel House Protector Nissan Ariya: FE0

Exploded View

Rear wheel house protector Grommet U nut
: Nissan Ariya Vehicle front

Removal & Installation

REMOVAL

Remove rear fillet molding. Refer to Removal & Installation.

Remove rear deflector. Refer to Removal & Installation.

Remove back side of sill cover. Refer to Removal & Installation.

Remove fixing screws that are fastened to rear bumper fascia assembly.

Remove rear wheel protector fixing screws, clips and plastic nuts, and then remove rear wheel house protector.

INSTALLATION

Install in the reverse order of removal.

Front Under Cover Nissan Ariya 1st generation

Exploded View

Front under cover bracket A Front under cover bracket B Front under cover front
Front under cover rear
: Nissan Ariya Vehicle front
N·m (kg-m, in-lb)
N·m (kg-m, ft-lb)

Removal & Installation

REMOVAL

  1. Remove front under cover front mounting bolts and fixing clips, and then remove front under cover front.

  2. Remove front under cover rear bracket A and B mounting bolts.

  3. Remove front under cover rear mounting bolts, and then remove front under cover rear, front under cover rear bracket A and front under cover rear B as a set.

  4. Remove front under cover rear bracket A and B fixing clips from front under cover rear.

INSTALLATION

Install in the reverse order of removal.

Rear Diffuser Nissan Ariya SUV

Exploded View

2WD

Rear diffuser bracket A Rear diffuser bracket B RH Rear diffuser bracket C RH
Rear diffuser bracket C LH Rear diffuser bracket B LH Rear diffuser front
Rear diffuser rear
: Nissan Ariya Vehicle front
: N·m (kg-m, in-lb)

AWD

Rear diffuser bracket A Rear diffuser bracket B RH Rear diffuser bracket B LH
Rear diffuser front Rear diffuser rear
: Nissan Ariya Vehicle front
: N·m (kg-m, in-lb)

Removal & Installation

REMOVAL

Rear Diffuser Front

Remove rear diffuser front mounting bolts and fixing clips, and then remove rear diffuser front.

Remove rear diffuser bracket mounting bolts, and then remove rear diffuser bracket.

Rear Diffuser Rear

Remove rear diffuser rear mounting nuts and fixing clips, and then remove rear diffuser rear.

INSTALLATION

Install in the reverse order of removal.

Roof Rail Nissan Ariya: FE0

Exploded View

Roof rail Roof panel
: N·m (kg-m, ft-lb)

Removal & Installation

REMOVAL

Remove headlining assembly. Refer to Removal & Installation.

Remove curtain air bag module mounting bolts and harness clip to make work space. Refer to Removal & Installation.

Remove roof rail mounting nuts, and then remove roof rail.

INSTALLATION

Install in the reverse order of removal.

Door Sash Cover Nissan Ariya SUV

Exploded View

Front door panel Front door sash cover front Front door sash cover rear
Rear door sash cover front Rear door sash cover rear Rear door panel
Double-sided tape [t : 2.5 mm (0.098 in)] Double-sided tape [t : 0.8 mm (0.031 in)] EPT seal [t : 3.0 mm (0.118 in)]
: Clip
: Pawl
: Nissan Ariya Vehicle front
: Always replace after every disassembly.

Front Door Sash Cover Nissan Ariya first Gen

Removal & Installation

REMOVAL

Front Door Sash Cover Front

Fully open front door.

Apply protective tape (A) on front door panel to protect the painted surface from damage.

Remove front door sash cover front fixing clip using a remover tool (A), and then remove front door sash cover front while cutting double-sided tape with a cutter.

: Clip

Front Door Sash Cover Rear

Remove front door outside molding. Refer to Removal & Installation.

Apply protective tapes (A) on front door panel to protect the painted surface from damage.

Disengage front door sash cover rear of upper side fixing pawl using a remove tool (A).

: Pawl

Insert a remover tool (A) between front door sash cover rear and front door panel, cut double-sided tape using a cutter (B) while lifting front door sash cover rear.

Remove front door sash cover rear.

INSTALLATION

Front Door Sash Cover Front

Note the following items, and then install in the reverse order of removal.

Insert front door sash cover front into the part of glass run.

Align the holes in front door panel with clip in front door sash cover front, and then install front door sash cover rear.

Crimp double-sided tape.

Front Door Sash Cover Rear

Note the following items, and then install in the reverse order of removal.

Align the pawl of front door glass run with upper side of front door sash cover rear.

Align with positioning pin of front door sash cover rear and insertion part of front door panel.

Install front door sash cover rear, and then crimp double-sided tape.

Install front door outside molding. Refer to Removal & Installation.

Rear Door Sash Cover Nissan Ariya 2026

Removal & Installation

REMOVAL

Rear Door Sash Cover Front

Remove rear door outside molding. Refer to Removal & Installation.

Apply protective tapes (A) on rear door panel to protect the painted surface from damage.

Disengage rear door sash cover front of upper side fixing pawl using a remove tool (A).

: Pawl

Insert a remover tool (A) between rear door sash cover front and rear door panel, cut double-sided tape using a cutter (B) while lifting rear door sash cover front.

Remove rear door sash cover front.

Rear Door Sash Cover Rear

Remove rear door outside molding. Refer to Removal & Installation.

Apply protective tapes (A) on rear door panel to protect the painted surface from damage.

Disengage rear door sash cover rear of upper side fixing pawl using a remove tool (A).

: Pawl

Insert a remover tool (A) between rear door sash cover rear and rear door panel, cut double-sided tape using a cutter (B) while lifting rear door sash cover rear.

: Clip

Remove rear door sash cover rear.

INSTALLATION

Rear Door Sash Cover Front

Note the following items, and then install in the reverse order of removal.

Align the pawl of rear door glass run with upper side of rear door sash cover front.

Align with positioning pin of rear door sash cover front and insertion part of rear door panel.

Install rear door sash cover front, and then Crimp double-sided tape.

Install rear door outside molding. Refer to Removal & Installation.

Rear Door Sash Cover Rear

Note the following items, and then install in the reverse order of removal.

Align the pawl of rear door glass run with upper side of rear door sash cover rear.

Align with positioning pin of rear door sash cover rear and insertion part of rear door panel.

Install rear door sash cover rear, and then Crimp double-sided tape.

Install rear door outside molding. Refer to Removal & Installation.

Door Outside Molding Nissan Ariya 2026

Exploded View

Front door panel Front door outside molding Rear door outside molding
Rear door Panel
: Pawl
: Nissan Ariya Vehicle front

Front Door Outside Molding Nissan Ariya 1st generation

Removal & Installation

REMOVAL

Fully open front door glass.

Remove front door sash cover front. Refer to Removal & Installation.

Apply protective tape (A) on the part to protect it from damage.

Disengage rear end of front door outside molding fixing pawl using remover tool (A) and (B).

: Pawl

Twist front door outside molding toward the direction of the arrow in the figure, and then lift up and remove it.

INSTALLATION

Install in the reverse order of removal.

Side Guard Molding Nissan Ariya: FE0

Exploded View

Front door panel Front side guard molding Rear side guard molding
Rear side guard molding rear Rear door panel Double-sided tape [t : 1.2 mm (0.047 in )]
Clip
: Clip
: Nissan Ariya Vehicle front
: Always replace after every disassembly.

Front Side Guard Molding Nissan Ariya 1st generation

Removal & Installation

REMOVAL

Fully open front door.

Apply protective tape (A) on the part to protect it from damage.

Insert a remover tool (A) between front side guard molding and front door panel, and then cut double-sided tape using a cutter (B) while lifting front side guard molding.

Disengage front door side guard molding fixing clips using a remover tool (A).

: Clip

Cut double-sided tape on the front side of front side guard molding, and then remove front side guard molding.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

Rear Side Guard Molding Nissan Ariya 2026

Removal & Installation

REMOVAL

Rear Side Guard Molding

Remove rear side guard molding rear.

Apply protective tape (A) on the part to protect it from damage.

Insert a remover tool (A) between rear side guard molding and rear door panel, and then cut double-sided tape using a cutter (B) while lifting rear side guard molding.

Disengage rear door side guard molding fixing clips using a remover tool (A).

: Clip

Cut double-sided tape on the front side of rear side guard molding, and then remove rear side guard molding.

Rear Side Guard Molding Rear

Fully open rear door.

Apply protective tape (A) on the part to protect it from damage.

Disengage rear door side guard rear molding fixing clips using a remover tool (A).

: Clip

Cut double-sided tape on the front side of rear side guard molding rear, and then remove rear side guard molding rear.

INSTALLATION

Rear Side Guard Molding

Note the following items, and then install in the reverse order of removal.

Rear Side Guard Molding Rear

Note the following items, and then install in the reverse order of removal.

Rear Deflector Nissan Ariya

Exploded View

Grommet Rear deflector
: Nissan Ariya Vehicle front
: Indicates that the part is connected at points with same symbol in actual Nissan Ariya vehicle.

Removal & Installation

REMOVAL

Remove rear deflector fixing clips .

Remove rear deflector fixing screws , and then remove rear deflector.

INSTALLATION

Note the following items, install in the reverse order of removal.

Sill Cover Nissan Ariya first Gen

Exploded View

Grommet Sill cover Screw grommet
:Clip
:Nissan Ariya Vehicle front

Removal & Installation

REMOVAL

Remove front fillet molding. Refer to Removal & Installation.

Remove rear deflector. Refer to Removal & Installation.

Remove sill cover fixing screw of front side.

Remove sill cover fixing screw of rear side.

Remove sill cover fixing screws in the bottom of sill cover.

Apply protective tapes (A) to the part to protect it from damage.

Remove sill cover of front side fixing clip using a remover tool (A).

:Clip

Remove sill cover fixing clips using a remover tool (A), and then remove sill cover.

:Clip
Nissan Ariya Vehicle front

INSTALLATION

Note the following item, and then install in the reverse order of removal.

Rear Fender Cover Nissan Ariya first Gen

Exploded View

Rear fender cover Double-sided tape [t: 2.0 mm (0.079 in)]
:Clip
: Always replace after every disassembly.
: Indicates that the part is connected at points with same symbol in actual Nissan Ariya vehicle.

Removal & Installation

REMOVAL

Fully open back door.

Remove rear fender cover fixing clips .

Apply protective tapes (A) on the part to protect it from damage.

Remove rear fender cover fixing clips using a remover tool (A).

:Clip

Cut double-sided tape, and then remove rear fender cover.

INSTALLATION

Note the following item, and then install in the reverse order of removal.

Rear Spoiler Nissan Ariya

Exploded View

Rear spoiler Rear washer nozzle Rear side spoiler cover
Grommet Back door panel High-mounted stop lamp
EPT seal [t : 3.0 mm (0.118 in)] Double-sided tape [t : 3.0 mm (0.118 in)]
: Clip
: Pawl
: Nissan Ariya Vehicle front
: Always replace after every disassembly.

Removal & Installation

REMOVAL

Remove back door upper finisher. Refer to Removal & Installation.

Remove cap using a remover tool (A).

Remove rear spoiler mounting nuts .

Disconnect harness connector .

Disconnect rear washer tube B .

Apply protective tapes (A) on the part to protect it from damage.

Remove rear spoiler fixing clips, and then remove rear spoiler while cutting double-sided tape with a cutter.

: Clip

Disengage rear spoiler cover fixing pawls while cutting EPT seal with a cutter, and then remove rear spoiler cover.

: Pawl

Remove rear washer nozzle. Refer to Removal & Installation.

Remove high-mounted stop lamp. Refer to Removal & Installation.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

Emblem Nissan Ariya 2026

Exploded view

Emblem A Emblem B

Removal and Installation

REMOVAL

Remove emblem from the panel while warming using an industrial dryer

INSTALLATION