Removal and Installation

In this manual: Removal and Installation
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
~14min read
  • Rear Wheel Hub and Housing
  • Rear Drive Shaft

Rear Wheel Hub and Housing Nissan Ariya

Exploded View

Axle housing Bushing Hub cap
Back plate Hub bolt Wheel hub and bearing assembly
Disc rotor Wheel hub lock nut Cotter pin
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

Removal and Installation

REMOVAL

Remove tires. Refer to Exploded View.

Remove wheel sensor from axle housing. Refer to Removal & Installation.

Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to Exploded View.

Remove disc rotor.

Remove wheel hub lock nut. Refer to Exploded View.

Remove wheel hub and bearing assembly mounting bolts .

Remove wheel hub and bearing assembly and back plate.

Remove radius rod. Refer to Removal & Installation.

Remove front lower link. Refer to Removal & Installation.

Remove coil spring. Refer to Removal & Installation.

Remove rear suspension arm mounting bolts and nuts from axle housing .

Separate rear suspension arm, and then remove axle housing.

Remove hub bolts from wheel hub and bearing assembly, using the ball joint remover (A) (commercial service tool).

Perform inspection after removal. Refer to Inspection.

INSTALLATION

Note the following, and install in the reverse order of removal.

  • Place a washer as shown in the figure to install the hub bolts by using the tightening force of the nut .

  • Align the matching marks made during removal when reusing the disc rotor.

  • Perform inspection after installation. Refer to Inspection.

Inspection

INSPECTION AFTER REMOVAL

Check wheel hub and bearing assembly for wear, cracks, and damage. Replace if there are.

INSPECTION AFTER INSTALLATION

Check wheel sensor harness for proper connection. Refer to Exploded View.

If pressing the piston of rear brake caliper assembly, perform "REMOVAL/REPLACEMENT OF REAR BRAKE PAD OR REAR BRAKE CALIPER". Refer to Removal & Installation.

Check wheel alignment. Refer to Inspection.

Adjust neutral position of steering angle sensor. Refer to Work Procedure.

Rear Drive Shaft Nissan Ariya SUV

Exploded View

FOR RH DRIVE SHAFT

Joint sub-assembly Circular clip Boot band
Boot Shaft Stopper ring
Spider assembly Snap ring Housing
Circular clip O-ring Bearing
Link SFT Bearing bracket
: Wheel side
: N·m (kg-m, ft-lb)
1 : Nissan genuine designated grease (Refer to parts catalog)
2 : Apply paste [service parts (440037S000)]
: Always replace after every disassembly.

FOR LH DRIVE SHAFT

Circular clip Dust shield Housing
Snap ring Spider assembly Stopper ring
Boot band Boot Shaft
Circular clip Joint sub-assembly
: Wheel side
: Fill NISSAN genuine grease or an equivalent.
: Always replace after every disassembly.

Removal and Installation

REMOVAL

Remove tires. Refer to Removal & Installation.

Remove wheel sensor from wheel hub and bearing assembly. Refer to Removal & Installation.

Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to Removal & Installation.

Remove disc rotor. If disc rotor cannot be removed, remove as follows.

Remove cotter pin, and then loosen wheel hub lock nut, using a wheel hub lock nut wrench (A) (SST: KV40104000).

Patch hub lock nut with a piece of wood. Hammer the wood to disengage wheel hub and bearing assembly from drive shaft.

Remove wheel hub and bearing assembly.

Remove back plate.

Remove hub cap.

Remove the rear drive shaft from transaxle assembly.

Remove the rear drive shaft from the rear final drive.

  • Use the drive shaft attachment (A) (SST: KV40107500) and a sliding hammer (B) while inserting tip of the drive shaft attachment between housing and final drive assembly.

Perform inspection after removal. Refer to Inspection.

INSTALLATION

Note the following, and install in the reverse order of removal.

RH SIDE

  • Install New O-ring to link shaft.

    • Insert drive shaft and slide the slide joint of drive shaft like a hammering to securely install it.

    LH SIDE

    When inserting drive shaft, attach a protector (special tool: KV38107900) (A) to oil seal to prevent damage to the side oil seal of the reducer. Then, insert drive shaft and slide the slide joint of drive shaft like a hammering to securely install it.

  • Align the matching marks made during removal when reusing the disc rotor.

  • Perform final tightening of bolts and nuts at suspension arm (rubber bushing), under unladen conditions with tires on level ground.

  • Tighten the wheel hub lock nut to the specified torque. Refer to Exploded View.

  • Perform inspection after installation. Refer to Inspection.

Disassembly and Assembly

DISASSEMBLY

Final Drive Side

Fix shaft with a vise.

Remove boot bands, and then remove boot from housing.

Remove stopper ring.

Put matching marks on housing and shaft.

Put matching marks on the spider assembly and shaft.

Remove snap ring , and then remove spider assembly from shaft.

Remove boot from shaft.

Remove circular clip housing. (For LH drive shaft)

Remove dust shield to housing. (For LH drive shaft)

Remove old grease on housing with paper towels.

Perform inspection after disassembly. Refer to Inspection.

Wheel Side

Fix shaft with a vise.

Remove boot bands. Then remove boot from joint sub-assembly.

Screw drive shaft puller (A) (commercial service tool) into joint sub-assembly screw part to a length 30 mm (1.18 in) or more. Support drive shaft with one hand and pull out joint sub-assembly from shaft.

Remove circular clip from shaft.

Remove boot from shaft.

Remove old grease on joint sub-assembly with paper towels.

Perform inspection after disassembly. Refer to Inspection.

ASSEMBLY

Final drive Side

Wrap serration on shaft with tape to protect boot from damage. Install new boot and boot band to shaft.

Remove the tape wrapped around the serrated on shaft.

To install the spider assembly , align it with the matching marks on the shaft during the removal, and direct the serration mounting surface to the shaft.

Secure spider assembly onto shaft with snap ring .

Assemble the housing onto spider assembly, and apply the balance of the specified amount grease.

Standard
Grease amount : Refer to Service Data.

Install stopper ring.

Align matching marks painted when housing were removed.

Install boot securely into grooves (indicated by “*” marks) shown in the figure.

To prevent from deformation of the boot, adjust the boot installation length to the value shown below (L) by inserting the suitable tool into the inside of boot from the large diameter side of boot and discharging inside air.

Standard
L : Refer to Service Data.

Install new boot bands securely.

  • For low profile type band

    1. Set boot band to the drive shaft boot groove and temporarily fix pawl of boot band to of boot band.

    2. Tighten boot band protrusions with boot band crimping tool (SST: KV40107310) (A) in the direction shown by arrows ().

  • For omega type band

    1. Secure the boot bands using the boot band crimping tool (A) (SST: KV40107300).

      Specified value
      M : 1.0 - 4.0 mm

Secure housing and shaft, and then make sure that they are in the correct position when rotating boot. Install them with new boot band when the mounting positions become incorrect.

Install dust shield to housing. (For LH drive shaft)

Install circular clip to housing. (For LH drive shaft)

Perform inspection after assembly. Refer to Inspection.

Wheel Side

Fill serration slot joint sub-assembly with NISSAN genuine grease or equivalent until the serration slot and ball groove become full to the brim.

Wrap serrated part of shaft with tape . Install boot band and boot to shaft. Be careful not to damage boot.

Remove the tape wrapped around the serrated on shaft.

Position the circular clip on groove at the shaft edge.

Align both center axles of the shaft edge and joint sub-assembly. Then assemble shaft with circular clip joint sub-assembly.

Install joint sub-assembly to shaft using plastic hammer.

Pull the joint sub-assembly in the axial direction away from transaxle assembly. Confirm that the joint sub assembly cannot be pulled out from shaft.

Fill into the joint sub-assembly inside with the remaining amount of grease from large diameter side of boot.

Total grease amount : Refer to Service Data.

Apply the balance of the specified amount of grease into the boot inside from large diameter side of boot.

Standard
Grease amount : Refer to Service Data.

Install the boot securely into grooves (indicated by “*” marks) shown in the figure.

To prevent from deformation of the boot, adjust the boot installation length to the specified value shown below (L) by inserting the suitable tool into inside of the boot from the large diameter side of boot and discharging the inside air.

Standard
L : Refer to Service Data.

Secure large and small ends of boot with new boot bands as shown in the figure.

  • For low profile type band

    1. Set boot band to the drive shaft boot groove and temporarily fix pawl of boot band to of boot band.

    2. Tighten boot band protrusions with boot band crimping tool (SST: KV40107310) (A) in the direction shown by arrows ().

  • For omega type band

    1. Secure the boot bands using the boot band crimping tool (A) (SST: KV40107300).

      Specified value
      M : 1.0 - 4.0 mm

Secure housing and shaft, and then make sure that they are in the correct position when rotating boot. Install them with new boot band when the mounting positions become incorrect.

Inspection

INSPECTION AFTER REMOVAL

  • Move joint up/down, left/right, and in the axial direction. Check for motion that is not smooth and for significant looseness.

  • Check boot for cracks or other damage, and also for grease leakage.

  • If a malfunction is found, disassemble drive shaft, and then replace with new one.

INSPECTION AFTER DISASSEMBLY

Shaft

Check shaft for runout, cracks, or other damage. Replace if there are any abnormal condition.

Joint Sub-Assembly (Wheel Side)

Check the following:

  • Joint sub-assembly for rough rotation and excessive axial looseness.

  • The inside of the joint sub-assembly for entry of foreign material.

  • Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly.

Replace joint sub-assembly if there are any non-standard conditions of components.

Housing and Spider assembly (Final Drive Side)

Replace housing and spider assembly if there is scratching or wear of housing roller contact surface or spider roller contact surface.

INSPECTION AFTER INSTALLATION

Check wheel sensor harness for proper connection. Refer to Exploded View.

If pressing the piston of rear brake caliper assembly, perform "REMOVAL/REPLACEMENT OF REAR BRAKE PAD OR REAR BRAKE CALIPER". Refer to Removal & Installation.

Check wheel alignment. Refer to Inspection.

Adjust neutral position of steering angle sensor. Refer to Work Procedure.