Basic Inspection
- Diagnosis and Repair Work Flow
- Additional Service When Replacing Air Bag Diagnosis Sensor Unit
- Configuration (air Bag Diagnosis Sensor Unit)
- Additional Service When Replacing Occupant Detection System Control Unit
- Zero Point Reset
Diagnosis and Repair Work Flow Nissan Ariya
Work Flow
OVERALL SEQUENCE

DETAILED FLOW
GET INFORMATION FOR SYMPTOM
Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurs).
Check operation condition of the function that is malfunctioning.
GO TO 2.
CHECK DTC
Check DTC.
Perform the following procedure if DTC is detected.
Record DTC (Print them out using CONSULT).
Erase DTC.
Study the relationship between the cause detected by DTC and the symptom described by the customer.
Check related service bulletins for information.
Are any symptoms described and any DTC detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC is detected>>GO TO 5.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.
>>GO TO 5.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.
>>GO TO 6.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected again.
Is DTC detected?
YES>>GO TO 7.
NO>>Check according to Intermittent Incident.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step 4, and determine the trouble diagnosis order based on possible causes and symptom.
>>GO TO 7.
DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?
YES>>GO TO 8.
NO>>Check according to Intermittent Incident.
REPAIR OR REPLACE THE MALFUNCTIONING PART
Repair or replace the malfunctioning part.
Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replacement.
Check DTC. If DTC is detected, erase it.
GO TO 9.
FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the malfunction is repaired securely.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the symptom is not detected.
Is DTC detected and does symptom remain?
YES-1>>DTC is detected: GO TO 7.
YES-2>>Symptom remains: GO TO 4.
NO>>Before returning the Nissan Ariya vehicle to the customer, always erase DTC.
Additional Service When Replacing Air Bag Diagnosis Sensor Unit Nissan Ariya 2023
Description
After replaced air bag diagnosis sensor unit, it is necessary to perform control unit configuration with CONSULT. For details, refer to Work Procedure.
Work Procedure
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
Replace air bag diagnosis sensor unit. Refer to Removal & Installation.
>>GO TO 2.
WRITING Nissan Ariya Vehicle SPECIFICATION
Perform configuration for air bag diagnosis sensor unit. Refer to Description.
>>WORK END
Configuration (air Bag Diagnosis Sensor Unit) Nissan Ariya SUV
Description
Vehicle specification needs to be written with CONSULT because it is not written after replacing the air bag diagnosis sensor unit.
CONSULT connects to network and then it downloads the configuration data from the server. Then CONSULT writes the Nissan Ariya vehicle specification to the air bag diagnosis sensor unit. Refer to Work Procedure.
Work Procedure
WRITING VEHICLE SPECIFICATION
With CONSULT
Perform writing Nissan Ariya vehicle specification to air bag diagnosis sensor unit according to "Replace ECU" in "CONSULT Operation Manual".
>>GO TO 2
CHECK ALL ECU SELF-DIAGNOSIS RESULTS
With CONSULT
Erase all ECU self-diagnosis results using CONSULT.
Power switch OFF.
Power switch ON.
Check that all ECU self-diagnosis results have no DTC.
WORK END
Additional Service When Replacing Occupant Detection System Control Unit Nissan Ariya first Gen
Description
When replacing occupant detection system control unit or removing and installing passenger seat, always perform zero point reset so that occupant detection system is activated normally. Refer to Work Procedure.
Work Procedure
PERFORM ZERO POINT RESET
Perform zero point reset. Refer to Description.
>>WORK END
Zero Point Reset Nissan Ariya 2026
Description
Zero point reset is an initializing procedure for occupant detection system that must be performed when replacing occupant detection system control unit or removing and installing passenger seat.
If zero point reset is not performed, the initialization is incomplete and occupant detection system does not operate normally. Refer to Work Procedure.
Work Procedure
PERFORM ZERO POINT RESET
Perform zero point reset.
Perform zero point reset after installing passenger seat to the Nissan Ariya vehicle
Never put any objects on passenger seat
Never apply excessive vibration to the Nissan Ariya vehicle
Never touch the vehicle
Never tilt the vehicle
Select start on “Zero point reset function” screen from, WORK SUPPORT of CONSULT “OCCUPANT DETECTION”.
“Zero point reset” starts.
GO TO 2.
CONFIRMATION OF SETTING
Proceed to “Zero point reset function” screen from work support of CONSULT “OCCUPANT DETECTION”.
Check that “Already performed” or “Not yet performed” is displayed on “Zero point reset current status”.
Is condition “Already performed”?
YES>>WORK END
NO>>Check condition as per the following, and perform zero point reset again.
Passenger seat is occupied by an object.
Excessive vibration is applied while performing zero point reset.
Occupant detection system is malfunctioning.
Passenger seat is occupied by an object.
Excessive vibration is applied while performing zero point reset.
Occupant detection system is malfunctioning.