Dtc/circuit Diagnosis

In this manual: Dtc/circuit Diagnosis
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
125steps
~750min
4/5difficulty
Done 0 of 125
  • B2490-13 Front Seat Heater Lh
  • B2490-19 Front Seat Heater Lh
  • B2491-13 Seat Blower Motor Lh
  • B2491-19 Seat Blower Motor Lh
  • U1ca6-02 Front Seat Heater Rh Communication
  • Power Supply and Ground Circuit
  • Lumbar Support Switch
  • Lumbar Support Pump
  • Front Seat Heater Lh
  • Rear Heated Seat Switch Lh
  • Rear Heated Seat Switch Indicator Lh
  • Seat Blower Motor Lh

B2490-13 Front Seat Heater Lh Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC detection condition
B2490-13 Front seat heater LH A Diagnosis condition Power switch ON and front heated seat switch LH ON
Signal (terminal) —
Threshold CPU inside the front seat heater LH detected a heater current of 0.2 A or less
Diagnosis delay time 6 minuites or more
B Diagnosis condition Power switch ON and front heated seat switch LH ON
Signal (terminal) —
Threshold CPU inside the front seat heater LH detected heater sensor signal voltage of 4.94 V or more
Diagnosis delay time 94 seconds or more

POSSIBLE CAUSE

Front seat cushion heater LH

FAIL-SAFE

Front seat heater LH operation is stopped

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Power switch ON.

  2. Front heated seat switch LH ON and wait at least 6 minutes or more.

  3. Check “Self Diagnostic Result” of “HVAC” using CONSULT.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

REPLACE SEAT CUSHION PAD

Replace seat cushion pad. Refer to Disassembly & Assembly.

>>

INSPECTION END

B2490-19 Front Seat Heater Lh Nissan Ariya: FE0

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC detection condition
B2490-19 Front seat heater LH A Diagnosis condition Power switch ON and front heated seat switch LH ON
Signal (terminal) —
Threshold CPU inside the front seat heater LH detected a heater current of 14 A or more
Diagnosis delay time 2 seconds or more
B Diagnosis condition Power switch ON and front heated seat switch LH ON
Signal (terminal) —
Threshold CPU inside the front seat heater LH detected a heater sensor signal voltage of 0.31 V or less
Diagnosis delay time 4 minuites or more
C Diagnosis condition Power switch ON and front heated seat switch LH ON
Signal (terminal) —
Threshold CPU inside the front seat heater LH counted 15,000 errors
Diagnosis delay time —

POSSIBLE CAUSE

  • Front seat cushion heater LH

  • Front seatback heater LH

FAIL-SAFE

Front seat heater LH operation is stopped

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Power switch ON.

  2. Front heated seat switch LH ON and wait at least 4 minutes or more.

  3. Check “Self Diagnostic Result” of “HVAC” using CONSULT.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK FRONT SEATBACK HEATER LH

Check front seatback heater LH. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace seat cushion pad. Refer to Disassembly & Assembly.

NO>>

Replace seatback assembly. Refer to Disassembly & Assembly.

Component Inspection

CHECK FRONT SEATBACK HEATER LH

  1. Power switch OFF.

  2. Disconnect front seatback heater LH connector.

  3. Check resistance between front seatback heater LH terminals.

    Front seatback heater LHResistance
    Terminal
    2 1 4.61 – 5.63 Ω

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace seatback assembly. Refer to Disassembly & Assembly.

B2491-13 Seat Blower Motor Lh Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC detection condition
B2491-13 Seat blower motor LH Diagnosis condition Power switch ON and front ventilation seat switch LH ON
Signal (terminal) —
Threshold CPU inside the front seat heater LH detected a seat blower motor current of 0.112 A or less
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Front seat cushion blower motor LH

  • Front seat cushion heater LH

FAIL-SAFE

Seat blower motor LH operation is stopped

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Power switch ON.

  2. Front ventilation seat switch LH ON and wait at least 2 minutes or more.

  3. Check “Self Diagnostic Result” of “HVAC” using CONSULT.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

REPLACE SEAT CUSHION PAD

Replace seat cushion pad. Refer to Disassembly & Assembly.

>>

INSPECTION END

B2491-19 Seat Blower Motor Lh Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC detection condition
B2491-19 Seat blower motor LH A Diagnosis condition Power switch ON and front ventilation seat switch LH ON
Signal (terminal) —
Threshold CPU inside the front seat heater LH detected a seat blower motor current of 4.52 A or more
Diagnosis delay time 2 seconds or more
B Diagnosis condition Power switch ON and front ventilation seat switch LH ON
Signal (terminal) —
Threshold CPU inside the front seat heater LH detected a seat blower motor speed control signal voltage of 1.0 V or less
Diagnosis delay time 1.5 seconds or more

POSSIBLE CAUSE

  • Front seat cushion blower motor LH

  • Front seatback blower motor LH

  • Front seat cushion heater LH

FAIL-SAFE

Seat blower motor LH operation is stopped

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Power switch ON.

  2. Front ventilation seat switch LH ON and wait at least 2 seconds or more.

  3. Check “Self Diagnostic Result” of “HVAC” using CONSULT.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Power switch OFF.

  2. Disconnect seatback blower motor LH connector.

  3. Power switch ON.

  4. Front ventilation seat switch LH ON and wait at least 2 seconds or more.

  5. Check “Self Diagnostic Result” of “HVAC” using CONSULT.

Is DTC detected?

YES>>

Replace seat cushion pad. Refer to Disassembly & Assembly.

NO>>

Replace seatback blower motor. Refer to Removal and Installation.

U1ca6-02 Front Seat Heater Rh Communication Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen itemsDTC detection condition
U1CA6-02 Front seat heater RH communication Diagnosis condition Power switch ON
Signal (terminal) LIN (heated seat) signal (terminal #45)
Threshold A/C auto amp. is not transmitting or receiving LIN communication with front seat heater RH
Diagnosis delay time 30 seconds or more

POSSIBLE CAUSE

  • Fuse

  • Harness or connectors (Front seat heater RH circuit is open or short to ground)

  • Front seat cushion heater RH

  • A/C auto amp.

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Power switch ON and wait at least 30 seconds or more.

  2. Check “Self Diagnostic Result” of “HVAC” using CONSULT.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK FUSE

  1. Power switch OFF.

  2. Check that the following fuse is not blown (open).

    Signal nameFuse No.
    Front seat heater RH power supply 83 (15A)

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK FRONT SEAT HEATER RH POWER SUPPLY VOLTAGE

  1. Disconnect front seat heater RH connector.

  2. Power switch ON.

  3. Check voltage between front seat heater RH harness connector and ground.

    +-Voltage
    Front seat heater RH
    ConnectorTerminal
    B470 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the front seat heater RH power supply circuit.

CHECK FRONT SEAT HEATER RH GROUND CIRCUIT (OPEN)

  1. Power switch OFF.

  2. Check continuity between front seat heater RH harness connector and ground.

    Front seat heater RHーContinuity
    ConnectorTerminal
    B470 4 Ground Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair the harness or connector.

CHECK FRONT SEAT HEATER RH LIN SIGNAL

  1. Power switch ON.

  2. Confirm output waveform between front seat heater RH harness connector and A/C auto amp. harness connector with oscilloscope.

    +–Output waveform
    Front seat heater RHA/C auto amp.
    ConnectorTerminalConnectorTerminal
    B470 3 M1 58

Is the inspection result normal?

YES>>

Replace seat cushion pad. Refer to Disassembly & Assembly.

NO>>

GO TO 5.

CHECK FRONT SEAT HEATER RH LIN SIGNAL CIRCUIT (OPEN)

  1. Power switch OFF.

  2. Disconnect A/C auto amp. connector.

  3. Check continuity between front seat heater RH harness connector and A/C auto amp. harness connector.

    Front seat heater RHA/C auto amp.Continuity
    ConnectorTerminalConnectorTerminal
    B470 3 M1 45 Existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair the harness or connector.

CHECK FRONT SEAT HEATER RH LIN SIGNAL CIRCUIT (SHORT TO GROUND)

  1. Disconnect the following connectors that are connected to terminal 45 of the A/C auto amp.

    • Front seat heater LH

    • Rear seat heater LH

    • Rear seat heater RH

    • Humidity sensor

  2. Check continuity between front seat heater RH harness connector and ground.

    Front seat heater RH—Continuity
    ConnectorTerminal
    B470 3 Ground Not existed

Is the inspection result normal?

YES>>

Replace A/C auto amp. Refer to Removal & Installation.

NO>>

Repair the harness or connector.

Power Supply and Ground Circuit Nissan Ariya 2023

Diagnosis Procedure

CHECK FUSE

  1. Power switch OFF.

  2. Check that the following fuse is not blown (open).

    Signal nameFuse No.
    Battery power supply 58 (20A)

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK DRIVER LUMBAR SUPPORT CONTROL MODULE BATTERY POWER SUPPLY VOLTAGE

  1. Disconnect driver lumbar support control module connector.

  2. Check voltage between driver lumbar support control module harness connector and ground.

    +-Voltage
    Driver lumbar support control module
    ConnectorTerminal
    B724 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the driver lumbar support control module battery power supply circuit.

CHECK DRIVER LUMBAR SUPPORT CONTROL MODULE GROUND CIRCUIT (OPEN)

Check continuity between driver lumbar support control module harness connector and ground.

Driver lumbar support control module—Continuity
ConnectorTerminal
B724 10 Ground Existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair the harness or connector.

Lumbar Support Switch Nissan Ariya 1st generation

Component Function Check

CHECK LUMBAR SUPPORT SWITCH FUNCTION

Operate the lumbar support switch and check that the seatback support operates.

Is the inspection result normal?

YES>>

Lumbar support switch is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK LUMBAR SUPPORT SWITCH POWER SUPPLY VOLTAGE

  1. Power switch OFF.

  2. Disconnect lumbar support switch connector.

  3. Check voltage between lumbar support switch harness connector and ground.

    +-

    Voltage

    (Approx.)
    Lumbar support switch
    ConnectorTerminal
    B725 80 Ground 12.5 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 2.

CHECK LUMBAR SUPPORT SWITCH SIGNAL CIRCUIT (OPEN)

  1. Disconnect driver lumbar support control module connector.

  2. Check continuity between lumbar support switch harness connector and driver lumbar support control module harness connector.

    Lumbar support switchDriver lumbar support control moduleContinuity
    ConnectorTerminalConnectorTerminal
    B725 80 B724 80 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK LUMBAR SUPPORT SWITCH SIGNAL CIRCUIT (SHORT TO GROUND)

Check continuity between lumbar support switch harness connector and ground.

Lumbar support switch—Continuity
ConnectorTerminal
B725 80 Ground Not existed

Is the inspection result normal?

YES>>

Replace lumbar support unit. Refer to Disassembly & Assembly.

NO>>

Repair the harness or connector.

CHECK LUMBAR SUPPORT SWITCH GROUND CIRCUIT (OPEN)

  1. Disconnect driver lumbar support control module connector.

  2. Check continuity between lumbar support switch harness connector and driver lumbar support control module harness connector.

    Lumbar support switchDriver lumbar support control moduleContinuity
    ConnectorTerminalConnectorTerminal
    B725 81 B724 81 Existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair the harness or connector.

CHECK LUMBAR SUPPORT SWITCH

Check lumbar support switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace lumbar support unit. Refer to Disassembly & Assembly.

NO>>

Replace lumbar support switch. Refer to Removal and Installation.

Component Inspection

CHECK LUMBAR SUPPORT SWITCH

  1. Power switch OFF.

  2. Disconnect lumbar support switch connector.

  3. Check resistance between lumbar support switch terminals.

    Lumbar support switchConditionResistance: kΩ
    Terminal
    80 81 Lumbar support switch Operate (upward) 3.855 – 4.217
    Operate (downward) 1.440 – 1.622
    Operate (forward) 0.640 – 0.742
    Operate (backward) 0.241 – 0.287
    Release ∞

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace lumbar support switch. Refer to Removal and Installation.

Lumbar Support Pump Nissan Ariya 2026

Component Function Check

CHECK LUMBAR SUPPORT PUMP FUNCTION

Operate the lumbar support switch forward / upward / downward, and check from the sound that the lumbar support pump operates.

Is the inspection result normal?

YES>>

Lumbar support pump is OK

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK LUMBAR SUPPORT PUMP POWER SUPPLY VOLTAGE

  1. Power switch OFF.

  2. Disconnect lumbar support pump connector.

  3. Check voltage between lumbar support pump harness connector and ground.

    +-Condition

    Voltage

    (Approx.)
    Lumbar support pump
    ConnectorTerminal
    B726 82 Ground Lumbar support Forward/upward/downward 12 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 2.

CHECK LUMBAR SUPPORT PUMP POWER SUPPLY CIRCUIT (OPEN)

  1. Disconnect driver lumbar support control module connector.

  2. Check continuity between lumbar support pump harness connector and driver lumbar support control module harness connector.

    Lumbar support pumpDriver lumbar support control moduleContinuity
    ConnectorTerminalConnectorTerminal
    B726 82 B724 82 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK LUMBAR SUPPORT PUMP POWER SUPPLY CIRCUIT (SHORT TO GROUND)

Check continuity between lumbar support pump harness connector and ground.

Lumbar support pump—Continuity
ConnectorTerminal
B726 82 Ground Not existed

Is the inspection result normal?

YES>>

Replace lumbar support unit. Refer to Disassembly & Assembly.

NO>>

Repair the harness or connector.

CHECK LUMBAR SUPPORT PUMP GROUND CIRCUIT

  1. Disconnect driver lumbar support control module connector.

  2. Check continuity between lumbar support pump harness connector and driver lumbar support control module harness connector.

    Lumbar support pumpDriver lumbar support control moduleContinuity
    ConnectorTerminalConnectorTerminal
    B726 83 B724 83 Existed

Is the inspection result normal?

YES>>

Replace lumbar support unit. Refer to Disassembly & Assembly.

NO>>

Repair the harness or connector.

Front Seat Heater Lh Nissan Ariya 2023

Component Function Check

CHECK FRONT SEAT HEATER LH FUNCTION

  1. Power switch ON.

  2. Check that seat cushion and seatback of front seat LH warms when operating front heated seat switch LH.

Is the inspection result normal?

YES>>

Front seat heater LH is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK FUSE

  1. Power switch OFF.

  2. Check that the following fuse is not blown (open).

    Signal nameFuse No.
    Front seat heater LH power supply 84 (15A)

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK FRONT SEAT HEATER LH POWER SUPPLY VOLTAGE

  1. Disconnect front seat heater LH connector.

  2. Power switch ON.

  3. Check voltage between front seat heater LH harness connector and ground.

    +-Voltage
    Front seat heater LH
    ConnectorTerminal
    B472 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the front seat heater LH power supply circuit.

CHECK FRONT SEAT HEATER LH GROUND CIRCUIT (OPEN)

  1. Power switch OFF.

  2. Check continuity between front seat heater LH harness connector and ground.

    Front seat heater LHーContinuity
    ConnectorTerminal
    B472 4 Ground Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair the harness or connector.

CHECK FRONT SEAT HEATER LH LIN SIGNAL

  1. Power switch ON.

  2. Confirm output waveform between front seat heater LH harness connector and A/C auto amp. harness connector with oscilloscope.

    +–Output waveform
    Front seat heater LHA/C auto amp.
    ConnectorTerminalConnectorTerminal
    B472 3 M1 58

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 5.

CHECK FRONT SEAT HEATER LH LIN SIGNAL CIRCUIT (OPEN)

  1. Power switch OFF.

  2. Disconnect A/C auto amp. connector.

  3. Check continuity between front seat heater LH harness connector and A/C auto amp. harness connector.

    Front seat heater LHA/C auto amp.Continuity
    ConnectorTerminalConnectorTerminal
    B472 3 M1 45 Existed

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair the harness or connector.

CHECK FRONT SEAT HEATER LH LIN SIGNAL CIRCUIT (SHORT TO GROUND)

  1. Disconnect the following connectors that are connected to terminal 45 of the A/C auto amp.

    • Front seat heater RH

    • Rear seat heater LH

    • Rear seat heater RH

    • Humidity sensor

  2. Check continuity between front seat heater LH harness connector and ground.

    Front seat heater LH—Continuity
    ConnectorTerminal
    B472 3 Ground Not existed

Is the inspection result normal?

YES>>

Replace A/C auto amp. Refer to Removal & Installation.

NO>>

Repair the harness or connector.

CHECK FRONT SEATBACK HEATER LH

Check front seatback heater LH. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace seat cushion pad. Refer to Disassembly & Assembly.

NO>>

Replace seatback assembly. Refer to Disassembly & Assembly.

Component Inspection

CHECK FRONT SEATBACK HEATER LH

  1. Power switch OFF.

  2. Disconnect front seatback heater LH connector.

  3. Check resistance between front seatback heater LH terminals.

    Front seatback heater LHResistance
    Terminal
    2 1 4.61 – 5.63 Ω

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace seatback assembly. Refer to Disassembly & Assembly.

Rear Heated Seat Switch Lh Nissan Ariya 2026

Component Function Check

CHECK REAR HEATED SEAT SWITCH LH FUNCTION

  1. Set the Nissan Ariya vehicle to READY.

  2. Check that rear heated seat switch LH indicator (Low, Mid, High) turns ON when operating rear heated seat switch LH.

Is the inspection result normal?

YES>>

Rear heated seat switch LH is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK REAR HEATED SEAT SWITCH LH POWER SUPPLY VOLTAGE

  1. Power switch OFF.

  2. Disconnect rear heated seat switch LH connector.

  3. Power switch ON.

  4. Check voltage between rear heated seat switch LH harness connector and ground.

    +-

    Voltage

    (Approx.)
    Rear heated seat switch LH
    ConnectorTerminal
    M209 5 Ground 12 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 2.

CHECK REAR HEATED SEAT SWITCH LH SIGNAL CIRCUIT (OPEN)

  1. Power switch OFF.

  2. Disconnect A/C control connector.

  3. Check continuity between rear heated seat switch LH harness connector and A/C control harness connector.

    Rear heated seat switch LHA/C controlContinuity
    ConnectorTerminalConnectorTerminal
    M209 5 M69 8 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK REAR HEATED SEAT SWITCH LH SIGNAL CIRCUIT (SHORT TO GROUND)

Check continuity between rear heated seat switch LH harness connector and ground.

Rear heated seat switch LH—Continuity
ConnectorTerminal
M209 5 Ground Not existed

Is the inspection result normal?

YES>>

Replace A/C control. Refer to Removal & Installation.

NO>>

Repair the harness or connector.

CHECK REAR HEATED SEAT SWITCH LH GROUND CIRCUIT (OPEN)

  1. Power switch OFF.

  2. Check continuity between rear heated seat switch LH harness connector and ground.

    Rear heated seat switch LHーContinuity
    ConnectorTerminal
    M209 7 Ground Existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair the harness or connector.

CHECK REAR HEATED SEAT SWITCH LH

Check rear heated seat switch LH. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Replace rear heated seat switch LH. Refer to Removal and Installation.

REPLACE A/C CONTROL

  1. Replace A/C control. Refer to Removal & Installation.

  2. Reconnect all connectors.

  3. Set the Nissan Ariya vehicle to READY.

  4. Check that rear heated seat switch LH indicator (Low, Mid, High) turns ON when operating rear heated seat switch LH.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace A/C auto amp. Refer to Removal & Installation.

Component Inspection

CHECK REAR HEATED SEAT SWITCH LH

  1. Power switch OFF.

  2. Disconnect rear heated sseat switch LH connector.

  3. Check continuity between rear heated seat switch LH terminals.

    Rear heated seat switch LHConditionContinuity
    Terminal
    5 7 Rear heated seat switch LH Pressed Existed
    Not pressed Not existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace rear heated seat switch LH. Refer to Removal and Installation.

Rear Heated Seat Switch Indicator Lh Nissan Ariya: FE0

Component Function Check

CHECK REAR HEATED SEAT SWITCH LH FUNCTION

  1. Set the Nissan Ariya vehicle to READY.

  2. Check that rear heated seat switch LH indicator (Low, Mid, High) turns ON when operating rear heated seat switch LH.

Is the inspection result normal?

YES>>

Rear heated seat switch LH is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK FUSE

  1. Power switch OFF.

  2. Check that the following fuse is not blown (open).

Signal nameFuse No.
Rear heated seat switch LH indicator power supply 8 (10A)

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK REAR HEATED SEAT SWITCH LH INDICATOR POWER SUPPLY VOLTAGE

  1. Disconnect rear heated seat switch LH connector.

  2. Power switch ON.

  3. Check voltage between rear heated seat switch LH harness connector and ground.

    +-Voltage
    Rear heated seat switch LH
    ConnectorTerminal
    M209 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the rear heated seat switch LH indicator power supply circuit.

CHECK REAR HEATED SEAT SWITCH LH INDICATOR SIGNAL VOLTAGE

  1. Power switch OFF.

  2. Reconnect rear heated seat switch LH connector.

  3. Disconnect A/C control connector.

  4. Power switch ON.

  5. Check voltage between A/C control harness connector and ground.

    +-Voltage
    A/C control
    ConnectorTerminal
    M69 9 Ground Battery voltage
    10
    11

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

CHECK REAR HEATED SEAT SWITCH LH INDICATOR SIGNAL CIRCUIT (OPEN)

  1. Power switch OFF.

  2. Disconnect rear heated seat switch LH connector.

  3. Check continuity between rear heated seat switch LH harness connector and A/C control harness connector.

    Rear heated seat switch LHA/C controlContinuity
    ConnectorTerminalConnectorTerminal
    M209 2 M69 9 Existed
    3 10
    4 11

Is the inspection result normal?

YES>>

Replace rear heated seat switch LH. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

REPLACE A/C CONTROL

  1. Replace A/C control. Refer to Removal & Installation.

  2. Reconnect all connectors.

  3. Set the Nissan Ariya vehicle to READY.

  4. Check that rear heated seat switch LH indicator (Low, Mid, High) turns ON when operating rear heated seat switch LH.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace A/C auto amp. Refer to Removal & Installation.

Seat Blower Motor Lh Nissan Ariya first Gen

Component Function Check

CHECK SEAT BLOWER MOTOR LH FUNCTION

  1. Power switch ON.

  2. Operate the front ventilation seat switch LH, and check that the seat cushion blower motor LH and seatback blower motor LH operates.

Is the inspection result normal?

YES>>

Seat blower motor LH is OK.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK SEATBACK BLOWER MOTOR LH POWER SUPPLY

  1. Power switch OFF.

  2. Disconnect seatback blower motor LH connector.

  3. Power switch ON.

  4. Check voltage between seatback blower motor LH harness connector and ground.

    +-Condition

    Voltage

    (Approx.)
    Seatback blower motor LH
    ConnectorTerminal
    B722 1 Ground Front ventilation seat switch LH Low 13 V
    Mid
    High
    OFF 0 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace seat cushion pad. Refer to Disassembly & Assembly.

CHECK SEATBACK BLOWER MOTOR LH GROUND CIRCUIT (OPEN)

  1. Power switch OFF.

  2. Disconnect front seat heater LH connector.

  3. Check continuity between seatback blower motor LH harness connector and front seat heater LH terminal.

    Seatback blower motor LHFront seat heater LHContinuity
    ConnectorTerminalTerminal
    B722 3 4 Existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace seat cushion pad. Refer to Disassembly & Assembly.

CHECK SEATBACK BLOWER MOTOR LH SPEED CONTROL SIGNAL VOLTAGE

  1. Connect front seat heater LH connector.

  2. Power switch ON.

  3. Check voltage between seatback blower motor LH harness connector and ground.

    +-Condition

    Voltage

    (Approx.)
    Seatback blower motor LH
    ConnectorTerminal
    B723 2 Ground Front ventilation seat switch LH Low 7.5 V
    Mid 10.0 V
    High 12.5 V
    OFF 0 V

Is the inspection result normal?

YES>>

Replace seatback blower motor. Refer to Removal and Installation.

NO>>

Replace seat cushion pad. Refer to Disassembly & Assembly.