Dcdc (dc/dc Converter)

In this manual: Dcdc (dc/dc Converter)
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
37steps
~222min
5/5difficulty
Done 0 of 37
  • P1aa5-A2 Control Unit Supply Voltage
  • P1aa6-9e Input Voltage Sensor/ecu Switch
  • P1aad-48 High Voltage Current Sensor Error
  • P1aae-4b Temperature Sensor/system Error 1
  • P1aba-17 Low Voltage Value
  • P1abc-16 High Voltage Input Voltage

P1aa5-A2 Control Unit Supply Voltage Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTCCONSULT screen termsDTC detecting condition
P1AA5 A2 Control unit supply voltage Diagnosis condition READY, AUTO ACC or power switch ON
Signal DC/DC converter internal voltage
Threshold DC/DC converter internal voltage is less than 6.1 V
Detection time 1 second

POSSIBLE CAUSE

  • 12 V battery

  • Harness and connector

  • DC/DC converter

FAIL-SAFE

Not applicable

Confirmation Procedure

PRECONDITIONING

  • Press the power switch OFF with the driver's side door open, get out of the Nissan Ariya vehicle, close the driver's side door and wait for at least 4 minutes.

  • Check that 12 V battery voltage is 11 V or more.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Erase “self-diagnostic result” in “DC/DC CONVERTER” using CONSULT.

  2. Set the Nissan Ariya vehicle to READY and wait at least 1 second.

  3. Check “self-diagnostic result” in “DC/DC CONVERTER” using CONSULT.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

Check 12V battery. Refer to Work Flow.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace 12V battery. Refer to 12V BATTERY : Removal & Installation.

CHECK DC/DC CONVERTER CAN COMMUNICATION LINE

Check DC/DC converter CAN communication line installation condition visually and tactually.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

PERFORM SELF-DIAGNOSIS OF VCM

With CONSULT

  1. Power switch ON.

  2. Check “self-diagnostic result” in “EV/HEV” using CONSULT.

Is DTC detected?

YES>>

Perform the trouble diagnosis for the detected DTC.

NO>>

GO TO 4.

CHECK DC/DC CONVERTER OUTPUT VOLTAGE

Check voltage between 12V battery plus terminal and ground.

+-Voltage
12V battery
12V battery plus terminal Ground Approximately 13 - 15.5 V

Is the inspection result normal

YES>>

Replace DC/DC converter. Refer to DC/DC CONVERTER : Disassembly & Assembly.

NO>>

GO TO 5.

CHECK DC/DC CONVERTER 12V BATTERY VOLTAGE

+−Voltage
DC/DC converter
ConnectorTerminal
H4 7 Ground 12V battery voltage

YES>>

GO TO 6.

NO>>

GO TO 7.

CHECK DC/DC CONVERTER GROUND CIRCUIT

Check for continuation between the metal parts of the DC/DC converter and ground.

Is there continuation?

YES>>

Perform trouble cause simulation test. Refer to Intermittent Incident.

NO>>

Repair or replace error-detected parts.

CHECK FUSIBLE LINK

Check that the fusible link below is not blown.

Fusible link numberCapacity
A 450 A

Is the fusible link blown?

YES>>

Replace the fusible link after repairing the applicable circuit.

NO>>

GO TO 8.

CHECK 12V BATTERY CIRCUIT

  1. Disconnect battery terminal integrated fusible link harness connector.

  2. Disconnect DC/DC converter harness connector.

  3. Check for continuation between battery terminal integrated fusible link and DC/DC converter.

    Battery terminal integrated fusible linkDC/DC converterContinuity
    ConnectorTerminalConnectorTerminal
    H3 9 H4 7 Existing

  4. Also check harness for short to ground.

Is the inspection result normal?

YES>>

Check 12V battery power supply circuit.

NO>>

Repair or replace error-detected parts.

P1aa6-9e Input Voltage Sensor/ecu Switch Nissan Ariya 1st generation

DTC Description

DTC DETECTION LOGIC

DTCCONSULT screen termsDTC detecting condition
P1AA6 9E Input voltage sensor/ECU switch Diagnosis condition READY, AUTO ACC or power switch ON
Signal —
Threshold DC/DC converter cannot be shut off. Alternatively the shut off time is too long.
Detection time —

POSSIBLE CAUSE

DC/DC converter

FAIL-SAFE

Not applicable

Confirmation Procedure

PRECONDITIONING

  • Press the power switch OFF with the driver's side door open, get out of the Nissan Ariya vehicle, close the driver's side door and wait for at least 4 minutes.

  • Check that 12 V battery voltage is 11 V or more.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Erase “self-diagnostic result” in “DC/DC CONVERTER” using CONSULT.

  2. Set the Nissan Ariya vehicle to READY.

  3. Check “self-diagnostic result” in “DC/DC CONVERTER” using CONSULT.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

With CONSULT

Perform DTC confirmation procedure again. Refer to Confirmation Procedure.

Is DTC P1AA6-9E detected again?

YES>>

Replace DC/DC converter. Refer to DC/DC CONVERTER : Disassembly & Assembly.

NO>>

INSPECTION END

P1aad-48 High Voltage Current Sensor Error Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTCCONSULT screen termsDTC detecting condition
P1AAD 48 High voltage current sensor error Diagnosis condition READY, AUTO ACC or power switch ON
Signal —
Threshold An error in the DC/DC converter internal system is detected.
Detection time 1 second

POSSIBLE CAUSE

DC/DC converter

FAIL-SAFE

DC/DC converter output is stopped

Confirmation Procedure

PRECONDITIONING

  • Press the power switch OFF with the driver's side door open, get out of the Nissan Ariya vehicle, close the driver's side door and wait for at least 4 minutes.

  • Check that 12 V battery voltage is 11 V or more.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Erase “self-diagnostic result” in “DC/DC CONVERTER” using CONSULT.

  2. Set the Nissan Ariya vehicle to READY and wait at least 1 second.

  3. Check “self-diagnostic result” in “DC/DC CONVERTER” using CONSULT.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM SELF-DIAGNOSIS OF VCM

With CONSULT

  1. Power switch ON.

  2. Check “self-diagnostic result” result in “EV/HEV” using CONSULT.

Is DTC detected?

YES>>

Perform the trouble diagnosis for the detected DTC.

NO>>

GO TO 2.

PERFORM SELF-DIAGNOSIS OF HV BATTERY

With CONSULT

Check “self-diagnostic result” result in “HIGH VOLTAGE BATTERY” and “HIGH VOLTAGE BATTERY 2” using CONSULT.

Is DTC detected?

YES>>

Perform the trouble diagnosis for the detected DTC.

NO>>

GO TO 3.

PERFORM SELF-DIAGNOSIS OF INVERTER

With CONSULT

Check “self-diagnostic result” result in “MOTOR CONTROL” using CONSULT.

Is DTC detected?

YES>>

Perform the trouble diagnosis for the detected DTC.

NO>>

GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

With CONSULT

Perform DTC confirmation procedure again. Refer to Confirmation Procedure.

Is DTC P1AAD-48 detected again?

YES>>

Replace DC/DC converter.Refer to DC/DC CONVERTER : Disassembly & Assembly.

NO>>

INSPECTION END

P1aae-4b Temperature Sensor/system Error 1 Nissan Ariya SUV

DTC Description

DTC DETECTION LOGIC

DTCCONSULT screen termsDTC detecting condition
P1AAE 4B Temperature sensor/System error 1 Diagnosis condition READY, AUTO ACC or power switch ON
Signal —
Threshold An overheating error of the DC/DC converter is detected.
Detection time 1 second

POSSIBLE CAUSE

  • DC/DC converter coolant circuit

  • DC/DC converter

FAIL-SAFE

DC/DC converter output current is stopped

Confirmation Procedure

PRECONDITIONING

  • Move the vehicle to a cool place, press the power switch OFF with the driver's side door open, get out of the Nissan Ariya vehicle and after that close the driver's side door and wait for at least 10 minutes.

  • Check that 12 V battery voltage is 11 V or more.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Erase “self-diagnostic result” in “DC/DC CONVERTER” using CONSULT.

  2. Set the Nissan Ariya vehicle to READY and wait at least 1 second.

  3. Check “self-diagnostic result” in “DC/DC CONVERTER” using CONSULT.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC RELATED TO HIGH VOLTAGE COOLANT SYSTEM

Check “self-diagnostic result” result in “EV/HEV” using CONSULT.

Is DTC detected?

YES>>

Inspect items of detected DTC. Refer to DTC Index.

NO>>

GO TO 2.

HIGH VOLTAGE COOLANT SYSTEM INSPECTION

Inspect high voltage coolant system for coolant amount and leakage. Refer to COOLANT : Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

With CONSULT

Perform DTC confirmation procedure again. Refer to Confirmation Procedure.

Is DTC P1AAE-4B detected again?

YES>>

Replace DC/DC converter. Refer to DC/DC CONVERTER : Disassembly & Assembly.

NO>>

INSPECTION END

P1aba-17 Low Voltage Value Nissan Ariya

DTC Description

DTC DETECTION LOGIC

DTCCONSULT screen termsDTC detecting condition
P1ABA 17 Low voltage value Diagnosis condition READY, AUTO ACC or power switch ON
Signal —
Threshold When it is detected that more than 15.7 V is applied to the low voltage side of the DC/DC converter
Detection time 1 second

POSSIBLE CAUSE

  • 12 V battery

  • Other electrical components

FAIL-SAFE

DC/DC converter output is stopped

Confirmation Procedure

PRECONDITIONING

  • Press the power switch OFF with the driver's side door open, get out of the Nissan Ariya vehicle, close the driver's side door and wait for at least 4 minutes.

  • Check that 12 V battery voltage is 11 V or more.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Erase “self-diagnostic result” in “DC/DC CONVERTER” using CONSULT.

  2. Set the Nissan Ariya vehicle to READY and wait at least 1 second.

  3. Check “self-diagnostic result” in “DC/DC CONVERTER” using CONSULT.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK 12V BATTERY

Check 12V battery. Refer to Work Flow.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace 12V battery. Refer to 12V BATTERY : Removal & Installation.

PERFORM FULL SELF-DIAGNOSIS

With CONSULT

  1. Power switch ON.

  2. Check if a power supply circuit DTC is detected at another control unit using CONSULT.

Is DTC detected?

YES>>

Check the detected DTC.

NO>>

Check 12V battery power supply circuit.

P1abc-16 High Voltage Input Voltage Nissan Ariya first Gen

DTC Description

DTC DETECTION LOGIC

DTCCONSULT screen termsDTC detecting condition
P1ABC 16 High voltage input voltage Diagnosis condition READY, AUTO ACC or power switch ON
Signal —
Threshold The input voltage to the DC/DC converter is below 215 V
Detection time 1 second

POSSIBLE CAUSE

  • ECU related to EV system

  • High voltage harness

  • DC/DC converter

FAIL-SAFE

DC/DC converter output is stopped

Confirmation Procedure

PRECONDITIONING

  • Press the power switch OFF with the driver's side door open, get out of the Nissan Ariya vehicle, close the driver's side door and wait for at least 4 minutes.

  • Check that 12 V battery voltage is 11 V or more.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Erase “self-diagnostic result” in “DC/DC CONVERTER” using CONSULT.

  2. Set the Nissan Ariya vehicle to READY.

  3. Check the displayed “INPUT VOLTAGE” in the “DATA MONITOR” of “DC/DC CONVERTER” using CONSULT.

Is it below 215 V?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC RELATED TO HIGH VOLTAGE SYSTEM

With CONSULT

  1. Set the Nissan Ariya vehicle to READY and wait for at least 120 seconds.

  2. Check DTC related to high voltage system using CONSULT.

Is DTC related to high voltage system detected?

YES>>

Check the detected DTC.

NO>>

GO TO 2.

PRECONDITIONING

  1. Disconnect the high voltage circuit. Refer to HOW TO DISCONNECT HIGH VOLTAGE : Precautions.

  2. Check the voltage in the high voltage circuit. Refer to CHECK VOLTAGE IN HIGH VOLTAGE CIRCUIT : Precautions.

>>

GO TO 3.

CHECK HIGH VOLTAGE HARNESS-1

  1. Disconnect the high voltage junction box high voltage harness connector.

  2. Disconnect the inverter (front) high voltage harness connector.

  3. Check for continuation of the high voltage harness between the high voltage junction box side connector and the inverter (front) side connector.

    High voltage junction boxInverter (front)Continuity
    ConnectorTerminalConnectorTerminal
    H10 N H12 N Existing
    P P

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK HIGH VOLTAGE HARNESS-2

  1. Disconnect the Li-ion battery high voltage harness connector.

  2. Check for continuation of the high voltage harness between the inverter (front) side connector and the Li-ion battery side connector.

    Inverter (front)Li-ion batteryContinuity
    ConnectorTerminalConnectorTerminal
    H6 N H5 37 Existing
    P 38

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

With CONSULT

Perform DTC confirmation procedure again. Refer to Confirmation Procedure.

Is DTC P1ABC-16 detected again?

YES>>

Replace DC/DC converter. Refer to DC/DC CONVERTER : Disassembly & Assembly.

NO>>

INSPECTION END