Dtc/circuit Diagnosis

In this manual: Dtc/circuit Diagnosis
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
100steps
~600min
4/5difficulty
Done 0 of 100
  • B2c76-04 Ambient Light 1
  • Interior Room Lamp Power Supply Circuit
  • Interior Room Lamp Circuit
  • Interior Room Lamp Control Circuit
  • Personal Lamp Circuit
  • Accent Lighting Control Circuit
  • Luggage Room Lamp Control Circuit
  • Power Switch Illumination Circuit
  • Illumination Emblem Circuit

B2c76-04 Ambient Light 1 Nissan Ariya 2026

DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen termsDTC detection condition
B2C76-04 Ambient light 1 Diagnosis condition Power switch ON
Signal (terminal) Advanced ambient light signal
Threshold Detected advanced ambient light signal error
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector

  • Advanced ambient light (instrument upper RH)

  • BCM

FAIL SAFE

Advanced ambient light (instrument upper RH) OFF or dimmed lighting.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Power switch ON.

  2. Set the brightness to 100% with Nissan Ariya vehicle setting "Ambient Lighting" of combination meter.

  3. Select “Self Diagnostic Result” mode of “BCM” using CONSULT.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK SELF-DIAGNOSIS RESULT 1

With CONSULT

  1. Power switch ON.

  2. Set the brightness to 0% with Nissan Ariya vehicle setting "Ambient Lighting" of combination meter.

  3. Move the vehicle into the shade and wait 10 minutes.

  4. Set the brightness to 100% with Nissan Ariya vehicle setting "Ambient Lighting" of combination meter.

  5. Select “Self Diagnostic Result” mode of “BCM” using CONSULT.

Is DTC B2C76-04 detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK SELF-DIAGNOSIS RESULT 2

With CONSULT

Select “Self Diagnostic Result” mode of “BCM” using CONSULT.

Are the DTC B2C77-04, B2C78-04, and B2C79-04 detecting?

YES-1>>

All of the above DTCs are detected.: Perform diagnosis of DTC U1C03-08. Refer to DTC Description.

YES-2>>

Any of the above DTCs is detected.: After performing diagnosis of DTC B2C76-04, perform the diagnosis of the detected DTC. GO TO 3 .

NO>>

All of the above DTCs are not detected.: GO TO 3.

CHECK ADVANCED AMBIENT LIGHT POWER SUPPLY CIRCUIT

  1. Power switch OFF.

  2. Disconnect fuse block (J/B) connector and advanced ambient light (instrument upper RH) connector.

  3. Check continuity between fuse block (J/B) harness connector and advanced ambient light (instrument upper RH) harness connector.

    Fuse block (J/B)Advanced ambient light (instrument upper RH)Continuity
    ConnectorTerminalConnectorTerminal
    M74 93 M77 1 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK ADVANCED AMBIENT LIGHT GROUND CIRCUIT

Check continuity between advanced ambient light (instrument upper RH) harness connector and ground.

Advanced ambient light (instrument upper RH)—Continuity
ConnectorTerminal
M77 4 Ground Existed

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness.

CHECK ADVANCED AMBIENT LIGHT SIGNAL CIRCUIT

  1. Disconnect BCM connector.

  2. Check continuity between BCM harness connector and advanced ambient light (instrument upper RH) harness connector.

    BCMAdvanced ambient light (instrument upper RH)Continuity
    ConnectorTerminalConnectorTerminal
    M8 3 M77 2 Existed

Is the inspection result normal?

YES>>

Replace advanced ambient light (instrument upper RH). Refer to Replacement.

NO>>

Repair or replace harness.

Interior Room Lamp Power Supply Circuit Nissan Ariya 2026

Diagnosis Procedure

CHECK SYMPTOM

Check symptom (A or B).

A

All the following lamps do not turn ON.

  • Map lamp

  • Personal lamp

  • Accent light

  • Advanced ambient light

  • Luggage room lamp

  • Glove box lamp

  • Center box lamp

  • Flexible center storage lamp

  • Vanity mirror lamp

B Interior room lamp battery saver does not activate.
A>>

GO TO 2.

B>>

GO TO 8.

CHECK FUSE

  1. Power switch OFF.

  2. Check that the following fuse is not blown (open).

    LocationFuse No.Capacity
    Fuse block (J/B) 30 10 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the cause of blown (open).

NO>>

GO TO 3.

CHECK INTERIOR ROOM LAMP POWER SUPPLY

  1. Remove interior room lamp relay.

  2. Check voltage between interior room lamp relay harness connector and ground.

    (+)(-)Voltage
    Interior room lamp relay
    Terminal
    Coil upstream side Ground Battery voltage
    Switch upstream side

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness

CHECK INTERIOR ROOM LAMP RELAY 1

Check interior room lamp relay. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace interior room lamp relay.

CHECK INTERIOR ROOM LAMP RELAY CONTROL CIRCUIT 1

With CONSULT

  1. Install interior room lamp relay.

  2. Power switch ON.

  3. Select “Interior lamp” of "BCM (INT LAMP)" active test item.

  4. With operating the test items, check voltage between BCM harness connector and ground.

    (+)(–)ConditionVoltage
    BCM
    ConnectorTerminal
    M8 37 Ground Interior lamp ON 0 – 1 V
    OFF 9 – 16 V

Is the inspection result normal?

YES>>

GO TO 7.

NO-1>>

Continuity exists and remains unchanged: GO TO 6.

NO-2>>

Continuity does not exist and remains unchanged: Replace BCM. Refer to Removal and Installation.

CHECK INTERIOR ROOM LAMP RELAY CONTROL CIRCUIT 2

  1. Power switch OFF.

  2. Disconnect BCM connector and fuse block (J/B) connector.

  3. Check continuity between BCM harness connector and fuse block (J/B) harness connector.

    BCMFuse block (J/B)Continuity
    ConnectorTerminalConnectorTerminal
    M8 37 M72 126 Existed

Is the inspection result normal?

YES>>

Replace fuse block (J/B).

NO>>

Repair or replace harness.

CHECK INTERIOR ROOM LAMP POWER SUPPLY CIRCUIT

  1. Power switch OFF.

  2. Disconnect fuse block (J/B) connector and map lamp connector.

  3. Check continuity between fuse block (J/B) harness connector and map lamp harness connector.

    Fuse block (J/B)Map lampContinuity
    ConnectorTerminalConnectorTerminal
    M74 93 R9 1 Existed

Is the inspection result normal?

YES>>

Replace fuse block (J/B).

NO>>

Repair or replace harness.

CHECK INTERIOR ROOM LAMP RELAY 2

Check interior room lamp relay. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Replace interior room lamp relay.

CHECK INTERIOR ROOM LAMP RELAY CONTROL CIRCUIT 3

  1. Power switch OFF.

  2. Remove interior room lamp relay.

  3. Disconnect BCM connector.

  4. Check continuity between BCM harness connector and ground.

    BCM—Continuity
    ConnectorTerminal
    M8 37 Ground Not existed

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harnesses.

Component Inspection

CHECK INTERIOR ROOM LAMP RELAY

  1. Power switch OFF.

  2. Remove interior room lamp relay.

  3. Check continuity between interior room lamp relay terminals.

    Interior room lamp relayConditionContinuity
    Terminal
    12 V direct current supply between terminals and . Existed
    No current supply Not existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace interior room lamp relay.

Interior Room Lamp Circuit Nissan Ariya

Diagnosis Procedure

CHECK INTERIOR ROOM LAMP POWER SUPPLY CIRCUIT

  1. Power switch OFF.

  2. Disconnect following connectors.

    • Fuse block (J/B)

    • Map lamp

    • Personal lamp

    • Vanity mirror lamp

    • Glove box lamp

    • Center box lamp

    • Flexible center storage lamp

  3. Check continuity between fuse block (J/B) harness connector and each interior room lamp harness connector.

    Fuse block (J/B)Each interior room lampContinuity
    ConnectorTerminalConnectorTerminal
    M74 93 Map lamp R9 8 Existed
    Personal lamp RH R33 1
    Personal lamp LH R8
    Vanity mirror lamp RH R11 2
    Vanity mirror lamp LH R10
    Glove box lamp M59 1
    Center box lamp M168 10
    Flexible center storage lamp M623 1

Is the inspection result normal?

YES-1>>

Except flexible center storage lamp: GO TO 2.

YES-2>>

Flexible center storage lamp: GO TO 3.

NO>>

Repair or replace harnesses.

CHECK INTERIOR ROOM LAMP GROUND CIRCUIT 1

Check continuity between each interior room lamp harness connector and ground.

Each interior room lamp—Continuity
ConnectorTerminal
Map lamp R9 4 Ground Existed
Personal lamp RH R33 4
Personal lamp LH R8
Vanity mirror lamp RH R11 3
Vanity mirror lamp LH R10
Glove box lamp M59 4
Center box lamp M168 5

Is the inspection result normal?

YES-1>>

Map lamp: Replace map lamp. Refer to Removal & Installation.

YES-2>>

Personal lamp: Replace corresponding personal lamp. Refer to Removal & Installation.

YES-3>>

Vanity mirror lamp: Replace corresponding vanity mirror lamp. Refer to Removal & Installation.

YES-4>>

Glove box lamp: Replace glove box lamp. Refer to Replacement.

YES-5>>

Center box lamp. Replace center box lamp. Refer to Replacement.

NO>>

Repair or replace harnesses.

CHECK INTERIOR ROOM LAMP GROUND CIRCUIT 2

  1. Disconnect flexible center storage control module connector.

  2. Check continuity between flexible center storage lamp harness connector and flexible center storage control module harness connector.

    Flexible center storage lampFlexible center storage control moduleContinuity
    ConnectorTerminalConnectorTerminal
    M623 2 M621 12 Existed

Is the inspection result normal?

YES>>

Replace flexible center storage lamp. Refer to Replacement.

NO>>

Repair or replace harness.

Interior Room Lamp Control Circuit Nissan Ariya 2026

Component Function Check

CHECK MAP LAMP OPERATION

With CONSULT

  1. Turn map lamp door link switch ON.

  2. Open the front door (driver side).

  3. Power switch ON.

  4. Select “Front lamp” of "BCM (HEAD LAMP)" active test item.

  5. With operating the test items, check that map lamp turns ON/OFF.

    ON : Map lamp turns ON
    OFF : Map lamp turns OFF

Does the map lamp turns ON/OFF?

YES>>

Interior room lamp control circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK INTERIOR ROOM LAMP CONTROL SIGNAL CIRCUIT 1

With CONSULT

  1. Power switch OFF.

  2. Disconnect map lamp connector.

  3. Power switch ON.

  4. Select "Front lamp" of "BCM (HEAD LAMP)" active test.

  5. With operating the test item, check continuity BCM harness connector and ground.

    BCM—Test itemContinuity
    ConnectorTerminal
    B14 130 Ground Front lamp ON Existed
    OFF Not existed

Is the inspection result normal?

YES>>

GO TO 2.

NO-1>>

Continuity exists and remains unchanged: GO TO 3.

NO-2>>

Continuity does not exist and remains unchanged: Replace BCM. Refer to Removal and Installation.

CHECK INTERIOR ROOM LAMP CONTROL SIGNAL CIRCUIT 2

  1. Power switch OFF.

  2. Disconnect BCM connector.

  3. Check continuity between BCM harness connector and map lamp harness connector.

    BCMMap lampContinuity
    ConnectorTerminalConnectorTerminal
    B14 130 R9 2 Existed

Is the inspection result normal?

YES>>

Replace map lamp. Refer to Removal & Installation.

NO>>

Repair or replace harnesses.

CHECK INTERIOR ROOM LAMP CONTROL SIGNAL CIRCUIT 3

  1. Power switch OFF.

  2. Disconnect BCM connector.

  3. Check continuity between BCM harness connector and ground.

    BCM—Continuity
    ConnectorTerminal
    B14 130 Ground Not existed

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harnesses.

Personal Lamp Circuit Nissan Ariya: FE0

Component Function Check

CHECK PERSONAL LAMP OPERATION

  1. Power switch ON.

  2. With operating the map lamp all switch, check that personal lamp turns ON/OFF.

    ON : Personal lamp turns ON
    OFF : Personal lamp turns OFF

Does the personal lamp turns ON/OFF?

YES>>

Personal lamp circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK MAP LAMP OUTPUT

  1. Power switch ON.

  2. Turn map lamp all switch ON.

  3. Check voltage between map lamp harness connector and ground.

    (+)(-)Voltage
    Map lamp
    ConnectorTerminal
    R9 8 Ground 4.5 – 5.5 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace map lamp. Refer to Removal & Installation.

CHECK MAP LAMP OUTPUT CIRCUIT

  1. Power switch OFF.

  2. Turn map lamp all switch OFF.

  3. Disconnect map lamp connector and personal lamp connector.

  4. Check continuity between map lamp harness connector and personal lamp harness connector.

    Map lampPersonal lampContinuity
    ConnectorTerminalConnectorTerminal
    R9 8 RH R33 2 Existed
    LH R8

Is the inspection result normal?

YES>>

Replace corresponding personal lamp. Refer to Removal & Installation.

NO>>

Repair or replace harnesses.

Accent Lighting Control Circuit Nissan Ariya first Gen

Component Function Check

CHECK ACCENT LIGHT OPERATION

With operating the front door (driver side), check that accent light turns ON/OFF.

OPEN : Accent light turns ON
CLOSE : Accent light turns OFF

Does the accent light turns ON/OFF?

YES>>

Accent lighting control circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK ACCENT LIGHT POWER SUPPLY CIRCUIT

  1. Power switch OFF.

  2. Disconnect fuse block (J/B) connector and accent light connector.

  3. Check continuity between fuse block (J/B) harness connector and accent light harness connector.

    Fuse block (J/B)Accent lightContinuity
    ConnectorTerminalConnectorTerminal
    M74 93 Front door RH D10 1 Existed
    Front door LH D50
    Instrument lower M60 1

Is the inspection normal?

YES>>

GO TO 2.

NO>>

Repair or replace harness.

CHECK ACCENT LIGHT CONTROL SIGNAL CIRCUIT 1

Check continuity between BCM harness connector and ground.

BCM—ConditionContinuity
ConnectorTerminal
B15 150 Ground Driver side door Open Existed
Close Not existed

Is the inspection result normal?

YES>>

GO TO 3.

NO-1>>

Continuity exists and remains unchanged: GO TO 4.

NO-2>>

Continuity does not exist and remains unchanged: Replace BCM. Refer to Removal and Installation.

CHECK ACCENT LIGHT CONTROL SIGNAL CIRCUIT 2

  1. Disconnect BCM connector.

  2. Check continuity between BCM harness connector and accent light harness connector.

    BCMAccent lightContinuity
    ConnectorTerminalConnectorTerminal
    B15 150 Front door RH D10 4 Existed
    Front door LH D50
    Instrument lower M60 4

Is the inspection result normal?

YES-1>>

Front door: Replace corresponding accent light (front door). Refer to Exploded View.

YES-2>>

Instrument lower: Replace accent light (instrument lower). Refer to Replacement.

NO>>

Repair or replace harnesses.

CHECK ACCENT LIGHT CONTROL SIGNAL CIRCUIT 3

  1. Disconnect BCM connector.

  2. Check continuity between BCM harness connector and ground.

    BCM—Continuity
    ConnectorTerminal
    B15 150 Ground Not existed

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harnesses.

Luggage Room Lamp Control Circuit Nissan Ariya

Component Function Check

CHECK LUGGAGE ROOM LAMP OPERATION

With CONSULT

  1. Power switch ON.

  2. Select “Trunk/luggage lamp” of "BCM (TRUNK)" active test item.

  3. With operating the test items, check that luggage room lamp turns ON/OFF.

    ON : Luggage room lamp ON
    OFF : Luggage room lamp OFF

Does luggage room lamp turns ON/OFF?

YES>>

Luggage room lamp control circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK LUGGAGE ROOM LAMP POWER SUPPLY CIRCUIT

  1. Power switch OFF.

  2. Disconnect fuse block (J/B) and luggage room lamp connector.

  3. Check continuity between fuse block (J/B) harness connector and luggage room lamp harness connector.

    Fuse block (J/B)Luggage room lampContinuity
    ConnectorTerminalConnectorTerminal
    M74 93 RH B134 2 Existed
    LH B133

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace harnesses.

CHECK LUGGAGE ROOM LAMP CONTROL SIGNAL

With CONSULT

  1. Connect fuse block (J/B) connector.

  2. Power switch ON.

  3. Select "Trunk/luggage lamp" of "BCM (TRUNK)" active test.

  4. With operating the test item, check continuity BCM harness connector and ground.

    BCM—Test itemContinuity
    ConnectorTerminal
    M8 30 Ground Trunk/luggage lamp ON Existed
    OFF Not existed

Is the inspection result normal?

YES>>

GO TO 3.

NO-1>>

Continuity exists and remains unchanged: GO TO 4.

NO-2>>

Continuity does not exist and remains unchanged: Replace BCM. Refer to Removal and Installation.

CHECK LUGGAGE ROOM LAMP CONTROL SIGNAL CIRCUIT 1

  1. Power switch OFF.

  2. Disconnect BCM connector.

  3. Check continuity between BCM harness connector and luggage room lamp harness connector.

    BCMLuggage room lampContinuity
    ConnectorTerminalConnectorTerminal
    M8 30 RH B133 3 Existed
    LH B134

Is the inspection result normal?

YES>>

Replace corresponding luggage room lamp. Refer to Removal & Installation.

NO>>

Repair or replace harness.

CHECK LUGGAGE ROOM LAMP CONTROL SIGNAL CIRCUIT 2

  1. Power switch OFF.

  2. Disconnect BCM connector.

  3. Check continuity between BCM harness connector and ground.

    BCM—Continuity
    ConnectorTerminal
    M8 30 Ground Not existed

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

Power Switch Illumination Circuit Nissan Ariya 1st generation

Diagnosis Procedure

CHECK POWER SWITCH ILLUMINATION POWER SUPPLY

  1. Power switch ON.

  2. Check voltage between Intelligent Key unit harness connector and the ground.

    (+)(-)ConditionVoltage
    Intelligent Key unit
    ConnectorTerminal
    M79 10 Ground Power switch illumination ON
    OFF 0 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace Intelligent Key unit. Refer to Removal and Installation.

CHECK POWER SWITCH ILLUMINATION CIRCUIT

  1. Power switch OFF.

  2. Disconnect Intelligent Key unit connector and power switch connector.

  3. Check continuity between Intelligent Key unit harness connector and power switch harness connector.

    Intelligent Key unitPower switchContinuity
    ConnectorTerminalConnectorTerminal
    M79 10 M143 5 Existed
  4. Check continuity between Intelligent Key unit harness connector and ground.

    Intelligent Key unit—Continuity
    ConnectorTerminal
    M79 10 Ground Not existed

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harnesses.

CHECK POWER SWITCH ILLUMINATION GROUND CIRCUIT

Check continuity between power switch harness connector and ground.

Power switch—Continuity
ConnectorTerminal
M143 6 Ground Existed

Is the inspection result normal?

YES>>

Replace power switch. Refer to Removal and Installation.

NO>>

Repair or replace harnesses.

Illumination Emblem Circuit Nissan Ariya: FE0

Component Function Check

CHECK ILLUMINATION EMBLEM OPERATION

Check that illumination emblem turns ON/OFF when the Nissan Ariya vehicle is set to READY.

READY : Illumination emblem turns ON
Except READY : Illumination emblem turns OFF

Does the illumination emblem turns ON/OFF?

YES>>

Illumination emblem circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK ILLUMINATION EMBLEM POWER SUPPLY

With set the Nissan Ariya vehicle to READY, check voltage between illumination emblem harness connector and ground.

(+)(-)ConditionVoltage
Illumination emblem
ConnectorTerminal
B138 1 Ground Nissan Ariya Vehicle condition READY 6 – 16 V
Except READY 0 – 1 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK ILLUMINATION EMBLEM POWER SUPPLY CIRCUIT

  1. Power switch OFF.

  2. Disconnect IPDM E/R connector and illumination emblem connector.

  3. Check continuity between IPDM E/R harness connector and illumination emblem harness connector.

    IPDM E/RIllumination emblemContinuity
    ConnectorTerminalConnectorTerminal
    E42 56 B138 1 Existed
  4. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R—Continuity
    ConnectorTerminal
    E42 56 Ground Not existed

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK ILLUMINATION EMBLEM GROUND CIRCUIT

  1. Power switch OFF.

  2. Disconnect illumination emblem connector.

  3. Check continuity between illumination emblem harness connector and ground.

    Illumination emblem—Continuity
    ConnectorTerminal
    B138 2 Ground Existed

Is the inspection result normal?

YES>>

Replace illumination emblem. Refer to Replacement.

NO>>

Repair or replace harness.