Basic Inspection

In this manual: Basic Inspection
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
4steps
~24min
5/5difficulty
Done 0 of 4
  • Diagnosis and Repair Work Flow
  • Refrigerant
  • Lubricant
  • Performance Test

Diagnosis and Repair Work Flow Nissan Ariya: FE0

Work Flow

DESCRIPTION OF TROUBLE DIAGNOSIS FLOWCHART

DETAILS OF TROUBLE DIAGNOSIS FLOWCHART

INTERVIEW FOR MALFUNCTION

Interview the customer to obtain the malfunction information.

>>

GO TO 2.

SYMPTOM CHECK

Check the malfunction based on the information obtained from the customer. Check if any other malfunctions are present.

Insufficient cooling·Insufficient heating>>

GO TO 3.

Coolant leakage>>

GO TO 6.

Noise>>

GO TO 7.

CONTROL SYSTEM DIAGNOSIS

Perform control system diagnosis.Refer to Work Flow. in “HAC Heater & Air Conditioner Control System.“

No malfunction detected>>

GO TO 4.

Malfunctioning is detected>>

GO TO 8.

PERFORMANCE TEST

Perform the performance inspection. Refer to Inspection.

>>

GO TO 5.

TROUBLE DIAGNOSIS FOR UNUSUAL PRESSURE

Perform diagnosis based on the gauge pressure diagnosis table, and identify the location of the malfunction. Refer to Symptom Table.

Insufficient refrigerant>>

GO TO 6.

Other than the above>>

GO TO 8.

CHECK REFRIGERANT FOR LEAKAGE

Perform the refrigerant leakage check and identify the location of the leak. Refer to Leak Test.

>>

GO TO 8.

TROUBLE DIAGNOSIS FOR NOISE

Perform diagnosis based on the noise diagnosis table, and identify the location of the malfunction. Refer to Symptom Table.

>>

GO TO 8.

MALFUNCTION PARTS REPAIR

Repair or replace malfunctioning part.

>>

GO TO 9.

REPAIR CHECK (OPERATION CHECK)

Check operation and verify that the system is operating normally.

Is check result normal?

YES>>

Trouble diagnosis is complete.

NO>>

GO TO 2.

Refrigerant Nissan Ariya 1st generation

Description

CONNECTION OF SERVICE TOOLS AND EQUIPMENT

Be certain to follow the manufacturer’s instructions for connecting to the machine.

Leak Test

DETECTING LEAKAGES WITH FLUORESCENT INDICATOR

CHECK REFRIGERANT LEAKAGE USING ELECTRICAL LEAK DETECTOR

  • Never allow refrigerant vapor, shop chemical vapors, cigarette smoke, or others around the Nissan Ariya vehicle.

  • Always check refrigerant leakage in a low air flow environment so that refrigerant may not disperse when leakage occurs.

Connect recovery/recycling/recharging equipment (for HFO-1234yf) or manifold gauge to A/C service valve.

Check that refrigerant gas pressure is 345 kPa (3.5 bar, 3.5 kg/cm2, 50 psi) or more when temperature is 16 °C or more. When pressure is lower than the specified value, fully recover all refrigerant and then charge with refrigerant from the service can to the specified level.

Clean area where refrigerant leakage check is performed, and check refrigerant leakage along all surfaces of pipe connections and A/C system components using electrical leak detector probe.

Repair or replace parts where refrigerant leakage is detected. (Leakage is detected but leakage location is unknown. GO TO 5.)

Start the Nissan Ariya vehicle and set A/C control in the following conditions.

  • A/C switch: ON

  • HEAT switch: OFF

  • Mode switch: Ventilation set

  • Intake switch: Recirculation set

  • Temperature setting: Full cold

  • Blower motor speed: Maximum speed set

Operate A/C for 2 minutes or longer.

Stop the A/C. Check again for refrigerant leakage. GO TO 3.

Recycle Refrigerant

Perform oil return operation. Refer to Perform Lubricant Return Operation. (If refrigerant or lubricant leakage is detected in a large amount, omit this step, and then GO TO 2.)

Check gauge pressure readings of recovery/recycling/recharging equipment (for HFO-1234yf ). When remaining pressure exists, recycle refrigerant from high-pressure hose and low-pressure hose.

Remove A/C service valve cap from the Nissan Ariya vehicle.

Connect recovery/recycling/recharging equipment (for HFO-1234yf ) to the A/C service valve.

Operate recovery/recycling/recharging equipment (for HFO-1234yf), and recycle refrigerant from the Nissan Ariya vehicle.

Evacuate air for 10 minutes or more to remove any remaining refrigerant integrated to compressor lubricant, etc.

Refrigerant recycle operation is complete.

Charge Refrigerant

Connect manifold gauge (for HFO-1234yf) to the service valve.

Connect vacuum pump to manifold gauge and operate the pump. Apply vacuum to the cooler cycle for approximately 25 minutes or longer.

Check the airtightness of A/C system for 25 minutes or more. If pressure raises more than the specified level, charge A/C system with approximately 200 g (0.4 lb) refrigerant and check that there is no refrigerant leakage. Refer to Leak Test.

If parts other than compressor were replaced, add compressor oil according to parts that were replaced. Refer to Lubricant Adjusting Procedure for Components Replacement Except Compressor.

Charge the A/C system from a service can with the specified amount of refrigerant.

Check that A/C system operates normally.

Disconnect manifold gauge.

Install A/C service valve cap.

Refrigerant charge is complete.

Lubricant Nissan Ariya SUV

Description

MAINTENANCE OF LUBRICANT LEVEL

The compressor lubricant is circulating in the system together with the refrigerant. It is necessary to fill compressor with lubricant when replacing A/C system parts or when a large amount of refrigerant leakage is detected. It is important to always maintain lubricant level within the specified level. Or otherwise, the following conditions may occur.

  • Insufficient lubricant amount: Stuck compressor

  • Excessive lubricant amount: Insufficient cooling (caused by insufficient heat exchange)

Specified lubricant Refer to Lubricant.

Inspection

If there is a malfunction (abnormal noise from inside, cooling failure) in electric compressor unit, check compressor oil.

  1. Remove electric compressor. Refer to Removal & Installation.

  2. Refer to the diagram and judge drained compressor oil.

  • Judgement result 1 : Replace only electric compressor.

  • Judgement result 2 : Replace electric compressor and accumulator.

Perform Lubricant Return Operation

Start the vehicle and set to the following conditions.

  • A/C switch: ON

  • HEAT switch: OFF

  • Blower motor speed: Maximum speed set

  • Intake switch: Recirculation set

  • Temperature setting: Full cold

Perform lubricant return operation for approximately 10 minutes.

Stop A/C operation.

Lubricant return operation is complete.

Lubricant Adjusting Procedure for Components Replacement Except Electric Compressor

Fill with lubricant for the amount that is calculated according to the following conditions.

Example: Lubricant amount to be added when replacing evaporator and inner condenser [m (US fl oz, Imp fl oz)] = 40 (1.4, 1.4) + 20 (0.7, 0.7) + α

ItemLubricant amount to be added to A/C system m (US fl oz, Imp fl oz)
Replace evaporator 40 (1.4, 1.4)
Replace condenser 20 (0.7, 0.7)
Replace inner condenser 20 (0.7, 0.7)
Replace battery coolant chiller 10 (0.3, 0.4)
Replace accumulator 40 (1.4, 1.4) + The amount of lubrication extracted from the removed accumulator.
Refrigerant leakage is detected Large amount leakage 30 (1.0, 1.1)
Small amount leakage —
Lubricant amount that is recycled together with refrigerant during recycle operation α

Lubricant Adjusting Procedure for Electric Compressor Replacement

Drain lubricant from removed electric compressor and measure lubricant amount.Turn electric compressor so that it faces downward, and drain compressor oil from high-pressure port and low-pressure port .

Measure total amount of lubricant that is drained from removed electric compressor.

Drain lubricant from a new electric compressor that is calculated according to the following conditions.

: New electric compressor
: Removed electric compressor

Amount to be drained (A)

[m (US fl oz, Imp fl oz)] = FC − (DC + SC + R + α)
FC : Lubricant amount that a new electric compressor contains [220 (7.4, 7.7)]
DC : Lubricant amount that is drained from removed electric compressor
SC : Lubricant amount that remains inside of removed electric compressor [20 (0.7, 0.7)]
R : Lubricant amount to be added according to components that are removed except electric compressor
α : Lubricant amount that is recycled together with refrigerant during recycle operation

ItemLubricant amount to be added to A/C system m (US fl oz, Imp fl oz)
Replace evaporator 40 (1.4, 1.4)
Replace condenser 20 (0.7, 0.7)
Replace inner condenser 20 (0.7, 0.7)
Replace battery coolant chiller 10 (0.3, 0.4)
Replace accumulator 40 (1.4, 1.4) + The amount of lubrication extracted from the removed accumulator.

Example: Lubricant amount to be drained from a new electric compressor when replacing electric compressor and condenser [m (US fl oz, Imp fl oz)] [DC = 60 (2.0, 2.1), α = 5 (0.2, 0.2)]

220 (7.4, 7.7) − [60 (2.0, 2.1) + 20 (0.7, 0.7) + 20 (0.7, 0.7) + 5 (0.2, 0.2)] = 115 (3.9, 4.0)

Install electric compressor and check the operation.

Performance Test Nissan Ariya first Gen

Inspection

INSPECTION PROCEDURE

  1. Connect the manifold gauge.

  2. Set the vehicle, and set to the following condition.

Test condition
Surrounding conditionIndoors or in the shade (in a well-ventilated place)
Nissan Ariya Vehicle condition Door Closed
Door glass Full open
Hood Open
A/C condition Temperature control switch or dial Full cold
A/C switch ON
HEAT switch OFF
Mode switch (Ventilation) set
Intake switch (Recirculation) set
Blower motor speed Maximum speed set

Maintain test condition until A/C system becomes stable. (Approximately 10 minutes)

Check that the characteristics for “intake temperature vs. discharge temperature” and “ambient temperature vs. pressure” are within the standard values.

When test results are within the specified value, inspection is complete.

If any of test result is out of the specified value, perform diagnosis by gauge pressure. Refer to Symptom Table.

RECIRCULATING-TO-DISCHARGE AIR TEMPERATURE TABLE

Inside air (Recirculating air) at blower assembly inlet

Discharge air temperature from center ventilator

°C (°F)

Relative humidity

%

Air temperature

°C (°F)
50 – 60 20 (68) 7.2 – 9.3 (45.0 – 48.7)
25 (77) 10.5 – 13.0 (50.9 – 55.4)
30 (86) 13.9 – 16.8 (57.0 – 62.2)
35 (95) 18.0 – 21.3 (64.4 – 70.3)
60 – 70 20 (68) 9.3 – 11.3 (48.7 – 52.3)
25 (77) 13.0 – 15.5 (55.4 – 59.9)
30 (86) 16.8 – 19.7 (62.2 – 67.5)
35 (95) 21.3 – 24.6 (70.3 – 76.3)

AMBIENT AIR TEMPERATURE-TO-OPERATING PRESSURE TABLE

Fresh air

High-pressure (Discharge side)

kPa (kg/cm2, psi)

Low-pressure (Suction side)

kPa (kg/cm2, psi)

Relative humidity

%

Air temperature

°C (°F)
50 – 70 25 (77)

979 – 1,197

(10.0 – 12.2, 142.0 – 173.6)

233 – 285

(2.4 – 2.9, 33.8 – 41.3)
30 (86)

1,182 – 1,444

(12.1 – 14.7, 171.4 – 209.4)

266 – 326

(2.7 – 3.3, 38.6 – 47.3)
35 (95)

1,360 – 1,662

(13.9 – 17.0, 197.2 – 241.0)

314 – 384

(3.2 – 3.9, 45.5 – 55.7)
40 (104)

1,499 – 1,833

(15.3 – 18.7, 217.4 – 265.8 )

373 – 455

(3.8 – 4.6, 54.1 – 66.0)