Removal and Installation

In this manual: Removal and Installation
How to Use This Manual — 1Precautions — 1Preparation — 1Vehicle Information — 1Basic Inspection — 1Preparation. Commercial Service Tools Or/and Repair Part — 1Description — 1Component Parts — 1System — 1Diagnosis System (vcm) — 1Ecu Diagnosis Information. Vcm — 1Ev Control System — 1Ev/hev (vcm) — 1Component Parts /circuit Diagnosis — 1Ev Control System — 1Periodic Maintenance. Ev System Warning Lamp — 1Removal and Installation. Vcm — 1Traction Motor System :: Front Traction Motor — 1Preparation — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Traction Motor System :: Rear Traction Motor — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Ev Battery System :: 66kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 2Service Data — 1Ev Battery System :: 91kwh Li-Ion Battery — 1Description — 4Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Disassembly and Assembly — 1Service Data — 2Preparation. Vehicle Charging System — 1Vehicle Charging System :: Description — 1Component Parts — 2System — 1Diagnosis System (on-Board Charger) — 1Diagnosis System (dc/dc Converter) — 1Ecu Diagnosis Information — 1Vehicle Charging System — 1Charger/pd Module (on-Board Charger) — 1Cplc (cplc) — 1Dcdc (dc/dc Converter) — 1Component Parts/circuit Diagnosis — 1Symptom Diagnosis — 1Evse Inspection — 1Periodic Maintenance — 1Removal and Installation — 1Disassembly and Assembly — 1Preparation. High Voltage Cooling System — 1Description — 1Symptom Diagnosis. Overheating Cause Analysis — 1Periodic Maintenance — 1Coolant — 1Removal and Installation — 1Radiator — 1Service Data — 1Removal and Installation. Accelerator Control System — 1Reduction Gear: Re1f62a — 1Removal and Installation — 1Transaxle & Transmission :: Electric Shift — 1Description — 3Basic Inspection — 2Dtc Diagnosis — 2Component Parts /circuit Diagnosis — 1Removal and Installation — 1Rear Final Drive: Rn1r62a — 1Removal and Installation — 1Preparation. Front Axle System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data. Front Drive Shaft — 12wd — 14wd — 1Periodic Maintenance — 1Removal and Installation — 1Preparation. Front Suspension System — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Road Wheels & Tires System — 1Description — 1System — 1Ecu Diagnosis Information. Bcm (body Control Module) — 1Tpms — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Road Wheels & Tires — 1Removal and Installation — 1Service Data — 1Preparation. Brake System — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Electrically-Driven Intelligent Brake Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1Service Data — 1Preparation. Parking Brake System — 1System Description — 1Component Parts — 1System — 1Ecu Diagnosis Information. Abs Actuator and Electric Unit (control Unit) — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Brake Control System :: With Vdc — 1System Description — 3Basic Inspection — 2Dtc/circuit Diagnosis — 1Symptom Diagnosis — 2Removal and Installation — 1Brake Control System :: Automatic Brake Hold — 1System Description — 3Component Parts /circuit Diagnosis — 1Removal and Installation — 1Brake Control System :: E-Step — 1System Description — 3Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Symptom Diagnosis — 1Rear Automatic Braking — 1System Description — 1Basic Inspection — 1Preparation. Steering System — 1System Description — 1Component Parts — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance. Steering Wheel — 1Removal and Installation — 1Service Data — 1System Description — 1Component Parts — 1Steering Control System — 1Ecu Diagnosis Information. Power Steering Control Module — 1Dtc/circuit Diagnosis — 1Component Parts /circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation. Power Steering Control Module — 1System Description — 1Removal and Installation — 1System Description — 1System — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Component Parts — 1Basic Inspection — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information. Air Bag Diagnosis Sensor Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1System Description. Description. Ventilation System — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1Basic Inspection — 1Symptom Diagnosis — 1Removal and Installation — 1Electric Compressor — 1Cooler Pipe and Hose — 1A/c Unit Assembly Cover — 1A/c Unit Assembly — 1Heater & Air Conditioning Control System :: Automatic Air Conditioning — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 2Dtc Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 2Preparation. Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Preparation. Instrument Panel — 1Component Parts — 1System — 1Ecu Diagnosis Information. Flexible Center Storage Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information. Driver Lumbar Support Control Module — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1System — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Manual Function Does Not Operate — 1Memory Function Does Not Operate — 1Removal and Installation — 1Preparation. Preparation — 1System Description — 1System (intelligent Key System) — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1U2141-87 Can Comm Circuit — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Automatic Back Door Operation Does Not Operate — 1Back Door Does Not Open — 1Door Does Not Lock/unlock with Door Lock and Unlock Switch — 1Removal and Installation — 1Hood — 1Radiator Core Support — 1Charge Port Lid — 1Front Fender — 1Front Door — 1Rear Door — 1Back Door — 1Hood Lock — 1Front Door Lock — 1Rear Door Lock — 1Back Door Lock — 1Outside Key Antenna — 1System Description — 1System — 1Ecu Diagnosis Information. Inverter (front), Inverter (rear), Bcm, Intelligent Key Unit — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Preparation — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Front Passenger Side Power Window Does Not Operate — 1Rear Lh Side Power Window Does Not Operate — 1Rear Rh Side Power Window Does Not Operate — 1Removal and Installation. Power Window Main Switch — 1Preparation. Preparation — 1System Description — 1Ecu Diagnosis Information — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Sunroof Switch Assembly — 1Symptom Diagnosis — 1Auto Operation Does Not Operate — 1Removal and Installation — 1Preparation — 1Description — 1Symptom Diagnosis. Squeak and Rattle Trouble Diagnoses — 1Removal and Installation — 1Service Information — 6Repair Information — 1Precaution — 1Preparation — 1Removal and Installation — 1Service Data — 1Preparation. Preparation — 1Component Parts — 1System — 1Ecu Diagnosis Information — 1Wiring Diagram. Door Mirror — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Power Supply and Ground Circuit — 1Symptom Diagnosis — 1Removal and Installation — 1Exterior Lighting System :: Led Headlamp — 1System Description — 3Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Periodic Maintenance — 1Removal and Installation — 1System Description — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm, Intelligent Key Unit — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis. Interior Lighting System Symptom — 1Removal and Installation — 1Service Data. Bulb Specifications — 1System Description — 1System — 1Ecu Diagnosis Information. Bcm, Ipdm E/r — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1System Description — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection. Diagnosis and Repair Work Flow — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Preparation. Preparation — 1Removal and Installation. Horn — 1Preparation. Commercial Service Tools Or/and Repair Part — 1System Description — 1Component Parts — 1Ecu Diagnosis Information. Approaching Vehicle Sound for Pedestrians (vsp) Control Unit — 1Approaching Vehicle Sound for Pedestrians (vsp) — 1Vsp [approaching Vehicle Sound for Pedestrians (vsp) Control Unit] — 1Approaching Vehicle Sound for Pedestrians (vsp) System — 1Removal and Installation — 1Removal and Installation — 1Wireless Charger — 1System Description — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Removal and Installation — 1Component Parts — 1System — 1Diagnosis System (bcm) — 1Ecu Diagnosis Information. Bcm — 1Basic Inspection — 1Dtc/circuit Diagnosis — 1Symptom Diagnosis — 1Removal and Installation — 1Can Fundamental — 1Description — 1Trouble Diagnosis — 1Can (controller Area Network) — 1Description — 1
6steps
~36min
5/5difficulty
Done 0 of 6
  • Front Coil Spring and Strut
  • Transverse Link
  • Front Stabilizer
  • Front Suspension Member

Front Coil Spring and Strut Nissan Ariya 2023

FRONT COIL SPRING AND STRUT : Exploded View

Piston rod lock nut Mounting insulator Mounting bearing
Bound bumper Upper rubber seat Coil spring
Lower rubber seat Strut Steering knuckle
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

FRONT COIL SPRING AND STRUT : Removal & Installation

REMOVAL

Remove cowl top cover. Refer to Removal and Installation.

Remove tires. Refer to ROAD WHEEL TIRE : Removal and Installation.

Remove wheel hub lock nut. Refer to FRONT WHEEL HUB AND KNUCKLE : Removal and Installation.

Remove front brake hose lock prate. Refer to FRONT BRAKE PIPING : Removal and Installation.

Remove front wheel sensor. Refer to FRONT WHEEL SENSOR : Removal and Installation.

Remove cylinder body from torque member and hang cylinder body with wire while preventing brake hose from being stretched.

Remove disc rotor.

Remove steering outer socket. Refer to STEERING GEAR AND LINKAGE: Exploded view.

Remove transverse link. Refer to TRANSVERSE LINK: Removal and Installation.

Separate stabilizer connecting rod from strut assembly.

Remove grommet in front of strut assembly mounting bolt.

: Nissan Ariya Vehicle front

Remove steering knuckle and strut assembly from vehicle.

Separate the connection of strut assembly and steering knuckle as follows.

  1. Remove strut connecting bolts from steering knuckle.

  2. Measure the gap (A) of the steering knuckle and then put mark of enlarged limit (B) on the chisel.

    Enlarged limit (B) = Gap (A) + 2.5 mm (0.098 in)

    Specified gap : 6.9 ± 0.5 mm (0.272 ± 0.02 in)

  3. Enlarge the gap of the steering knuckle with the chisel (A) (commercial service tool) not to surpass a limit as shown in the figure.

  4. Separate the connection of strut assembly and steering knuckle.

INSTALLATION

Note the followings, and install in the reverse order of removal.

Strut Assembly

When installing strut assembly to the vehicle, set the mounting insulator to the direction shown in the figure.

: Nissan Ariya Vehicle front

Strut Assembly and Steering Knuckle Connection

Install the steering knuckle to strut assembly as follows.

  • Align the gap of steering knuckle to the projection part of strut.

  • Tighten mounting bolt of steering knuckle until contacts stopper bracket end face while pushing it up with suitable jack.

  • When installing suspension component parts, the final tightening of rubber bush is performed while Nissan Ariya vehicle is under unladen conditions with tires on level ground.

  • Perform inspection after installation. Refer to FRONT COIL SPRING AND STRUT: Inspection.

  • After replacing strut, always follow the disposal procedure to discard the strut. Refer to FRONT COIL SPRING AND STRUT: Disposal.

FRONT COIL SPRING AND STRUT : Disassembly & Assembly

DISASSEMBLY

Install strut attachment (A) (SST: ST35652000) to strut assembly and secure it in a vise.

Using a spring compressor (A) (commercial service tool), compress coil spring between spring upper seat and lower seat (strut assembly) until coil spring with a spring compressor is free.

Check coil spring with spring compressor between spring upper seat and lower seat (strut assembly) is free. Remove piston rod lock nut while securing the piston rod tip not to turn piston rod.

Remove mounting insulator, mounting bearing upper rubber seat and bound bumper from strut.

After removing coil spring, gradually release the spring compressor (commercial service tool).

Remove lower rubber seat.

Remove strut attachment (A) (SST: ST35652000) from strut.

Perform inspection after disassembly. Refer to Inspection.

ASSEMBLY

Install strut attachment (SST: ST35652000) to strut and secure it in a vise.

Align protrusion at bottom of lower rubber seat with hole in the strut and then install lower rubber seat.

Compress coil spring using the spring compressor (commercial service tool), and install it to strut assembly.

Set bound bumper to piston rod of strut.

Install mounting bearing and upper rubber seat to strut.

Set the mounting insulator to the direction shown in the figure, and then install the mounting insulator and the upper rubber seat with the mounting bearing to the strut.

: Nissan Ariya Vehicle front

Dimension (A) : 5 mm (0.20 in) or less

Secure piston rod tip to prevent piston rod from turning, then tighten piston rod lock nut to the specified tightening torque.

Gradually release the spring compressor (A) (commercial service tool), and remove coil spring.

Remove the strut attachment (A) (SST: ST35652000) from strut.

FRONT COIL SPRING AND STRUT : Inspection

INSPECTION AFTER DISASSEMBLY

Strut

Check the following items, and replace the parts if necessary.

  • Strut for deformation, cracks or damage

  • Piston rod for damage, uneven wear or distortion

  • Oil leakage

Strut Mounting Insulator, Bound Bumper, Upper Rubber Seat and Lower Rubber Seat

Check strut mounting insulator, bound bumper, upper rubber seat and lower rubber seat for cracks, wear or damage, and replace the parts if necessary.

Coil Spring

Check coil spring for cracks, wear or damage and replace the parts if necessary.

INSPECTION AFTER INSTALLATION

  • Check wheel sensor harness for proper connector. Refer to FRONT WHEEL SENSOR : Exploded View.

  • Check wheel alignment. Refer to WHEEL ALIGNMENT : Inspection.

  • Adjust neutral position of steering angle sensor. Refer to Work Procedure.

FRONT COIL SPRING AND STRUT : Disposal

Set strut assembly horizontally to the ground with the piston rod fully extracted.

Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position () from top as shown in the figure to release gas gradually.

Dimension A : 20 – 30 mm (0.79 – 1.18 in)

Drain oil from drain hole by moving the piston rod several times.

Transverse Link Nissan Ariya 2026

TRANSVERSE LINK : Exploded View

Front suspension member Stopper Transverse link
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.

TRANSVERSE LINK : Removal & Installation

REMOVAL

Remove protector of water tube for battery.

Remove transverse link mounting bolts and nuts , and then remove transverse link from suspension member.

Remove transverse link from steering knuckle. Refer to Exploded view.

Perform inspection after removal. Refer to Inspection.

INSTALLATION

Note the following, and install in the reverse order of removal.

  • Never reuse transverse link mounting nut.

  • Perform final tightening of bolts and nuts at installation position of rubber bushing to the Nissan Ariya vehicle, under unladen conditions with tires on level ground.

  • Perform inspection after installation. Refer to Inspection.

TRANSVERSE LINK : Inspection

INSPECTION AFTER REMOVAL

Visual Inspection

Check the following items, and replace the parts if necessary.

  • Transverse link for deformation, cracks or damage.

  • Bushing for complete separation. (If completely separated, inner metal can be pulled out from transverse link.)

  • Ball joint boot for cracks or other damage, and also for grease leakage.

Ball Joint Check

Move the ball stud by hand and check that it moves smoothly without catching.

Swing Torque

  • Hook a spring balance (A) at cutout on ball stud and pull it. When ball stud begins moving, measure spring balance value. The specified value is as follows;

    Specified Value
    Swing torque : BALL JOINT : Service Data
    Measurement value of spring balance (cutout on ball stud) : BALL JOINT : Service Data
  • If swing torque exceeds specified range, replace transverse link assembly due to disassembly prohibited.

Axial end play

  1. Move ball stud at least ten times by hand to check for smooth movement.

  2. Move tip of ball stud in axial direction to check for looseness.

    • If there is axial end play, replace transverse link assembly.

Move the ball stud by hand and check that it moves smoothly without catching.

INSPECTION AFTER INSTALLATION

Check wheel sensor harness for proper connection. Refer to FRONT WHEEL SENSOR : Exploded View.

Check wheel alignment. Refer to WHEEL ALIGNMENT : Inspection.

Adjust neutral position of steering angle sensor. Refer to Work Procedure.

Front Stabilizer Nissan Ariya: FE0

FRONT STABILIZER : Exploded View

Front suspension member Stabilizer bar assembly Stabilizer connecting rod
Strut
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)

FRONT STABILIZER : Removal & Installation

REMOVAL

Remove tires. Refer to Removal and Installation.

Remove motor room under cover.

Remove stabilizer connecting rod. Refer to Exploded view.

Remove mounting bolts and the remove stabilizer assembly from suspension member.

Perform inspection after removal. Refer to Inspection.

INSTALLATION

Note the following, and install in the reverse order of removal.

  • When installing the stabilizer clamp mounting bolts, tighten in numerical order.

    Temporary tightening (by hand) : 1 – 3
    Temporary tightening (by tool) : 4→7
    Final tightening (Specified torque) : 8→11
    : Nissan Ariya Vehicle front
  • To install stabilizer connecting rod , tighten the mounting nut with the hexagonal part (A) on the stabilizer connecting rod side fixed.

  • Preform inspection after installation. Refer to Inspection.

FRONT STABILIZER : Inspection

INSPECTION AFTER REMOVAL

Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks or damage. Replace it if necessary.

INSPECTION AFTER INSTALLATION

Check wheel alignment. Refer to WHEEL ALIGNMENT : Inspection.

Adjust neutral position of steering angle sensor. Refer to Work Procedure.

Front Suspension Member Nissan Ariya 1st generation

FRONT SUSPENSION MEMBER : Exploded View

Front suspension member Front member stay (Right side) Reinforcement
Front member stay (Left side)
Comply with the assembly procedure when tightening. Refer to Removal and Installation (For 66 KWH) and Removal and Installation (For 91 KWH).
: Nissan Ariya Vehicle front
: N·m (kg-m, ft-lb)

FRONT SUSPENSION MEMBER : Removal & Installation

DANGER:

Because hybrid vehicles and electric vehicles contain a high voltage battery, there is a risk of electric shock, electric leakage, or similar accidents if the Nissan Ariya vehicle is handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.

REMOVAL

  • Disconnect high voltage circuit. Refer to HOW TO DISCONNECT HIGH VOLTAGE : Precautions.

  • Check voltage of high voltage circuit. Refer to CHECK VOLTAGE IN HIGH VOLTAGE CIRCUIT : Precautions.

Remove minus terminal of 12 V battery. Refer to 12 V BATTERY : Removal and Installation.

Remove tires. Refer to Removal and Installation.

Remove front under cover . Refer to Front under Cover : Removal and Installation.

: Nissan Ariya Vehicle front
: Li-ion battery under cover (front)

Remove Li-ion battery under cover (front) . Refer to Removal and Installation (For 66 KWH) and Removal and Installation (For 91 KWH).

: Nissan Ariya Vehicle front
: Front under cover

Drain coolant of Li-ion battery and high voltage system. Refer to COOLANT : Draining.

Drain oil from reducer. Refer to REDUCTION GEAR OIL : Draining.

Discharge A/C refrigerant gas. Refer to Recycle Refrigerant.

Remove right and left front fender protectors. Refer to Removal and Installation.

Remove right and left stabilizer connecting rods. Refer to Removal and Installation.

Remove right and left drive shafts. Refer to FRONT DRIVE SHAFT : Removal and Installation.

Remove high voltage supply unit.

Remove A/C pipe and A/C flexible hose .

: Nissan Ariya Vehicle front

Remove bus bar cover .

: Nissan Ariya Vehicle front

Remove bus bar mounting bolts and high voltage harness fixing bolts .

: Nissan Ariya Vehicle front

Cover High voltage area.

Remove high voltage harness mounting bracket from reduction gear.

: Nissan Ariya Vehicle front

Remove high voltage harness from bracket .

: Nissan Ariya Vehicle front

Remove mounting bolts and the remove reinforcement .

: Nissan Ariya Vehicle front

Disconnect high voltage harness from Li-ion battery and the remove bracket from Nissan Ariya vehicle.

: Nissan Ariya Vehicle front

Cover high voltage area.

Hold high voltage harness to Nissan Ariya vehicle side with rope (A).

: Nissan Ariya Vehicle front

Remove vehicle harness and harness clips.

  • Reduction gear (Upper side)

  • Traction motor (front and rear)

  • In-Nissan Ariya vehicle charger

  • Water pump for Li-ion battery

  • Water pump for high voltage system cooling

  • Power steering motor

Remove ground to body.

: Nissan Ariya Vehicle front
: Nissan Ariya Vehicle right side
: Nissan Ariya Vehicle left side

Remove water hose

  • Vehicle right side: Remove water hose from water pump for Li-ion battery.

    : Nissan Ariya Vehicle front

  • Vehicle left side: Remove water hose from water pump for high voltage cooling system.

    : Nissan Ariya Vehicle front

  • Vehicle left side: Remove water hose .

    : Nissan Ariya Vehicle front

Remove joint of steering shaft lower.

Remove under cover brackets .

: Nissan Ariya Vehicle front

Set jack to front suspension member.

Remove right and left member stays.

Remove mounting bolts of front suspension member. Refer to Removal and Installation.

Gradually lower the jack and remove front suspension member together with traction motor inverter, traction motor, and reduction gear from Nissan Ariya vehicle.

Remove traction motor inverter, traction motor and reduction gear from front suspension member. Refer to FRONT TRACTION MOTOR : Removal and Installation.

Remove rear motor mounting from front suspension member.

Remove the following parts from front suspension member.

  • Steering gear assembly: Refer to STEERING GEAR AND LINKAGE : Removal and Installation.

  • Front stabilizer: Refer to Removal and Installation.

  • Transverse Link: Refer to Removal and Installation.

Preform inspection after installation. Refer to Inspection.

INSTALLATION

Note the followings, and install in the reverse order of removal.

  • When installing member stay and front suspension member mounting bolts, temporarily tighten the bolts and then tighten to the specified torque. Refer to the following numerical tightening order:

    Temporary tightening : 1 → 2 → 3 → 4
    Final tightening (Specified torque) : 5 → 6 → 7 → 8

    : Nissan Ariya Vehicle front

  • Check wheel sensor harness for proper connection. Refer to Exploded view.

  • Check wheel alignment. Refer to WHEEL ALIGNMENT : Service Data.

  • When installing suspension component parts, the final tightening of rubber bush is performed while Nissan Ariya vehicle is under unladen conditions with tires on level ground.

  • Perform inspection after installation. Refer to Inspection.

FRONT SUSPENSION MEMBER : Inspection

INSPECTION AFTER REMOVAL

Check front suspension member for remarkable deformation, cracks, wear or damage. Replace it if necessary.

INSPECTION AFTER INSTALLATION

Check front wheel sensor harness for proper connection. Refer to FRONT WHEEL SENSOR : Exploded View.

Check wheel alignment. Refer to WHEEL ALIGNMENT : Inspection.

Adjust neutral position of steering angle sensor. Refer to Work Procedure.